Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:
gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'
and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):
sysfs: cannot create duplicate filename '/class/gpio/CBUS0'
Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: Johan Hovold <johan@kernel.org>
While we currently grab a runtime PM ref in nouveau's normal connector
detection code, we apparently don't do this for MST. This means if we're
in a scenario where the GPU is suspended and userspace attempts to do a
connector probe on an MSTC connector, the probe will fail entirely due
to the DP aux channel and GPU not being woken up:
[ 316.633489] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.635713] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.637785] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
...
So, grab a runtime PM ref here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds a mode where the vcore scheduling logic in HV KVM limits itself
to scheduling only virtual cores from the same VM on any given physical
core. This is enabled via a new module parameter on the kvm-hv module
called "one_vm_per_core". For this to work on POWER9, it is necessary to
set indep_threads_mode=N. (On POWER8, hardware limitations mean that KVM
is never in independent threads mode, regardless of the indep_threads_mode
setting.)
Thus the settings needed for this to work are:
1. The host is in SMT1 mode.
2. On POWER8, the host is not in 2-way or 4-way static split-core mode.
3. On POWER9, the indep_threads_mode parameter is N.
4. The one_vm_per_core parameter is Y.
With these settings, KVM can run up to 4 vcpus on a core at the same
time on POWER9, or up to 8 vcpus on POWER8 (depending on the guest
threading mode), and will ensure that all of the vcpus belong to the
same VM.
This is intended for use in security-conscious settings where users are
concerned about possible side-channel attacks between threads which could
perhaps enable one VM to attack another VM on the same core, or the host.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When an OS (currently only classic Mac OS) is running in KVM-PR and makes a
linked jump from code with split hack addressing enabled into code that does
not, LR is not correctly updated and reflects the previously munged PC.
To fix this, this patch undoes the address munge when exiting split
hack mode so that code relying on LR being a proper address will now
execute. This does not affect OS X or other operating systems running
on KVM-PR.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Consolidate metrics handling for ipv4 and ipv6
As part of the IPv6 fib info refactoring, the intent was to make metrics
handling for ipv6 identical to ipv4. One oversight in ip6_dst_destroy
led to confusion and a couple of incomplete attempts at finding and
fixing the resulting memory leak which was ultimately resolved by
ce7ea4af08 ("ipv6: fix memory leak on dst->_metrics").
Refactor metrics hanlding make the code really identical for v4 and v6,
and add a few test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv4 and ipv6 test cases for metrics (mtu) when fib entries are
created. Can be used with kmemleak to see leaks with both fib entries
and dst_entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the respective NAT helper module if the flow uses it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_block_dev() doesn't seem to be used anywhere in the tree.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Misc. bug fixes.
4 small bug fixes related to setting firmware message enables bits, possible
memory leak when probe fails, and ring accouting when RDMA driver is loaded.
Please queue these for -stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473e ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0 ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an unfortunate interaction between commit fbe1a850b3
("crypto: lrw - Fix out-of bounds access on counter overflow") and
commit c778f96bf3 ("crypto: lrw - Optimize tweak computation"),
we ended up with a version of next_index() that always returns 127.
Fixes: c778f96bf3 ("crypto: lrw - Optimize tweak computation")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
replace pci_enable_msix_exact() with pci_alloc_irq_vectors(). get the
required vector count from pci_msix_vec_count().
use struct nitrox_q_vector as the argument to tasklets.
Signed-off-by: Srikanth Jampala <Jampala.Srikanth@cavium.com>
Reviewed-by: Gadam Sreerama <sgadam@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use node based allocations for queues. consider the dma address
alignment changes, while calculating the queue base address.
added checks in cleanup functions. Minor changes to queue variable names
Signed-off-by: Srikanth Jampala <Jampala.Srikanth@cavium.com>
Reviewed-by: Gadam Sreerama <sgadam@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
check the flr capability using pcie_has_flr() and do the flr.
Signed-off-by: Srikanth Jampala <Jampala.Srikanth@cavium.com>
Reviewed-by: Gadam Sreerama <sgadam@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
fix compilation warnings with nitrox_debugfs.c while printing
atomic64_t types on arm64. typecast the atomic64_read() value to u64
This issue is reported by Ard Biesheuvel
drivers/crypto/cavium/nitrox/nitrox_debugfs.c:62:30:
warning: format ‘%lld’ expects argument of type ‘long long int’,
but argument 3 has type ‘long int’ [-Wformat=]
seq_printf(s, " Posted: %lld\n", atomic64_read(&ndev->stats.posted));
^
Fixes: 2a8780be9c (crypto: cavium/nitrox - updated debugfs information)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Srikanth Jampala <Jampala.Srikanth@cavium.com>
Reviewed-by: Gadam Sreerama <sgadam@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sparse complains thusly:
CHECK arch/x86/crypto/morus640-sse2-glue.c
arch/x86/crypto/morus640-sse2-glue.c:38:1: warning: symbol 'crypto_morus640_sse2_algs' was not declared. Should it be static?
CHECK arch/x86/crypto/morus1280-sse2-glue.c
arch/x86/crypto/morus1280-sse2-glue.c:38:1: warning: symbol 'crypto_morus1280_sse2_algs' was not declared. Should it be static?
CHECK arch/x86/crypto/morus1280-avx2-glue.c
arch/x86/crypto/morus1280-avx2-glue.c:38:1: warning: symbol 'crypto_morus1280_avx2_algs' was not declared. Should it be static?
and sparse is correct - these don't need to be global and polluting the namespace.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Ondrej Mosnacek <omosnacek@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver implements a (part of a) network driver, and fails to
build if we have turned off networking support:
drivers/crypto/caam/caamalg_qi2.o: In function `dpaa2_caam_fqdan_cb':
caamalg_qi2.c:(.text+0x577c): undefined reference to `napi_schedule_prep'
caamalg_qi2.c:(.text+0x578c): undefined reference to `__napi_schedule_irqoff'
drivers/crypto/caam/caamalg_qi2.o: In function `dpaa2_dpseci_poll':
caamalg_qi2.c:(.text+0x59b8): undefined reference to `napi_complete_done'
drivers/crypto/caam/caamalg_qi2.o: In function `dpaa2_caam_remove':
caamalg_qi2.c:(.text.unlikely+0x4e0): undefined reference to `napi_disable'
caamalg_qi2.c:(.text.unlikely+0x4e8): undefined reference to `netif_napi_del'
drivers/crypto/caam/caamalg_qi2.o: In function `dpaa2_dpseci_setup':
caamalg_qi2.c:(.text.unlikely+0xc98): undefined reference to `netif_napi_add'
From what I can tell, CONFIG_NETDEVICES is the correct dependency here,
and adding it fixes the randconfig failures.
Fixes: 8d818c1055 ("crypto: caam/qi2 - add DPAA2-CAAM driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Arnd reports that with Kees's latest VLA patches applied, the HMAC
handling in the QAT driver uses a worst case estimate of 160 bytes
for the SHA blocksize, allowing the compiler to determine the size
of the stack frame at compile time and throw a warning:
drivers/crypto/qat/qat_common/qat_algs.c: In function 'qat_alg_do_precomputes':
drivers/crypto/qat/qat_common/qat_algs.c:257:1: error: the frame size
of 1112 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Given that this worst case estimate is only 32 bytes larger than the
actual block size of SHA-512, the use of a VLA here was hiding the
excessive size of the stack frame from the compiler, and so we should
try to move these buffers off the stack.
So move the ipad/opad buffers and the various SHA state descriptors
into the tfm context struct. Since qat_alg_do_precomputes() is only
called in the context of a setkey() operation, this should be safe.
Using SHA512_BLOCK_SIZE for the size of the ipad/opad buffers allows
them to be used by SHA-1/SHA-256 as well.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes the following sparse warning:
drivers/crypto/ccp/psp-dev.c:444:5: warning:
symbol 'sev_get_firmware' was not declared. Should it be static?
Fixes: e93720606e ("crypto: ccp - Allow SEV firmware to be chosen based on Family and Model")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
quality field is currently documented as being 'per mill'. In fact the
math involved is:
add_hwgenerator_randomness((void *)rng_fillbuf, rc,
rc * current_quality * 8 >> 10);
thus the actual definition is "bits of entropy per 1024 bits of input".
The current documentation seems to have confused multiple people
in the past, let's fix the documentation to match code.
An alternative is to change core to match driver expectations, replacing
rc * current_quality * 8 >> 10
with
rc * current_quality / 1000
but that has performance costs, so probably isn't a good option.
Fixes: 0f734e6e76 ("hwrng: add per-device entropy derating")
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clang emits a warning about this construct:
drivers/crypto/ccp/sp-platform.c:36:36: warning: tentative array
definition assumed to have one element
static const struct acpi_device_id sp_acpi_match[];
^
1 warning generated.
Just remove the forward declarations and move the initializations up
so that they can be used in sp_get_of_version and sp_get_acpi_version.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For historical reasons, the AES-NI based implementation of the PCBC
chaining mode uses a special FPU chaining mode wrapper template to
amortize the FPU start/stop overhead over multiple blocks.
When this FPU wrapper was introduced, it supported widely used
chaining modes such as XTS and CTR (as well as LRW), but currently,
PCBC is the only remaining user.
Since there are no known users of pcbc(aes) in the kernel, let's remove
this special driver, and rely on the generic pcbc driver to encapsulate
the AES-NI core cipher.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It is best practice to have 1 binding per file, so board level bindings
should be separate for various misc SoC bindings. Move the Alpine CPU
control to al,alpine-smp and we can also remove a cross reference.
Cc: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
syzbot was able to trigger rcu stalls by calling write()
with large number of bytes.
Add a cond_resched() in the loop to avoid this.
Link: https://lkml.org/lkml/2018/8/23/1106
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+9436b02171ac0894d33e@syzkaller.appspotmail.com
Reviewed-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=slnZ
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2018-10-05' of git://anongit.freedesktop.org/drm/drm
Dave writes:
"amdgpu and two core fixes
Two fixes for amdgpu:
one corrects a use of process->mm
one fix for display code race condition that can result in a crash
Two core fixes:
One for a use-after-free in the leasing code
One for a cma/fbdev crash."
* tag 'drm-fixes-2018-10-05' of git://anongit.freedesktop.org/drm/drm:
drm/amdkfd: Fix incorrect use of process->mm
drm/amd/display: Signal hw_done() after waiting for flip_done()
drm/cma-helper: Fix crash in fbdev error path
drm: fix use-after-free read in drm_mode_create_lease_ioctl()
Fix a simple typo: Completetion -> Completion
Signed-off-by: Konrad Djimeli <kdjimeli@igalia.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The PCI bus config accessors could be inlined into other accessor
functions, which makes it so they can't be traced. Force them to never be
inlined so that ftrace can hook into these functions.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The type of a cache might not be specified by architectural mechanisms (ie
system registers), but its type might be specified in the PPTT. In this
case, we should populate the type of the cache, rather than leave it
undefined.
This fixes the issue where the cacheinfo driver will not populate sysfs
for such caches, resulting in the information missing from utilities like
lstopo and lscpu, thus degrading the user experience.
Fixes: 2bd00bcd73 (ACPI/PPTT: Add Processor Properties Topology Table parsing)
Reported-by: Vijaya Kumar K <vkilari@codeaurora.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a cache has an unknown type because neither the hardware nor the
firmware told us, an entry in the sysfs tree will be made, but the type
file will not be present. lscpu depends on the type file being present
for every entry, and will error out without printing system information
if lscpu cannot open the type file.
Presenting information about a cache without indicating its type is not
useful, therefore if we hit a cache with an unknown type, stop populating
sysfs so that userspace has the maximum amount of useful information.
This addresses the following lscpu error, which prevents any output.
lscpu: cannot open /sys/devices/system/cpu/cpu0/cache/index3/type: No such
file or directory
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the storage array in place it's now trivial to support CLOCK_TAI in
the vdso. Extend the base time storage array and add the update code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Matt Rickard <matt@softrans.com.au>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.823878601@linutronix.de
Dereferencing gtod->cycle_last all over the place and foing the cycles <
last comparison in the vclock read functions generates horrible code. Doing
it at the call site is much better and gains a few cycles both for TSC and
pvclock.
Caveat: This adds the comparison to the hyperv vclock as well, but I have
no way to test that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.741440803@linutronix.de
The code flow for the vclocks is convoluted as it requires the vclocks
which can be invalidated separately from the vsyscall_gtod_data sequence to
store the fact in a separate variable. That's inefficient.
Restructure the code so the vclock readout returns cycles and the
conversion to nanoseconds is handled at the call site.
If the clock gets invalidated or vclock is already VCLOCK_NONE, return
U64_MAX as the cycle value, which is invalid for all clocks and leave the
sequence loop immediately in that case by calling the fallback function
directly.
This allows to remove the gettimeofday fallback as it now uses the
clock_gettime() fallback and does the nanoseconds to microseconds
conversion in the same way as it does when the vclock is functional. It
does not make a difference whether the division by 1000 happens in the
kernel fallback or in userspace.
Generates way better code and gains a few cycles back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.657928937@linutronix.de
Now that the time getter functions use the clockid as index into the
storage array for the base time access, the switch case can be replaced.
- Check for clockid >= MAX_CLOCKS and for negative clockid (CPU/FD) first
and call the fallback function right away.
- After establishing that clockid is < MAX_CLOCKS, convert the clockid to a
bitmask
- Check for the supported high resolution and coarse functions by anding
the bitmask of supported clocks and check whether a bit is set.
This completely avoids jump tables, reduces the number of conditionals and
makes the VDSO extensible for other clock ids.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.574315796@linutronix.de
do_realtime_coarse() and do_monotonic_coarse() are now the same except for
the storage array index. Hand the index in as an argument and collapse the
functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.490733779@linutronix.de
do_realtime() and do_monotonic() are now the same except for the storage
array index. Hand the index in as an argument and collapse the functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.407955860@linutronix.de
It's desired to support more clocks in the VDSO, e.g. CLOCK_TAI. This
results either in indirect calls due to the larger switch case, which then
requires retpolines or when the compiler is forced to avoid jump tables it
results in even more conditionals.
To avoid both variants which are bad for performance the high resolution
functions and the coarse grained functions will be collapsed into one for
each. That requires to store the clock specific base time in an array.
Introcude struct vgtod_ts for storage and convert the data store, the
update function and the individual clock functions over to use it.
The new storage does not longer use gtod_long_t for seconds depending on 32
or 64 bit compile because this needs to be the full 64bit value even for
32bit when a Y2038 function is added. No point in keeping the distinction
alive in the internal representation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.324679401@linutronix.de
The sequence count in vgtod_data is unsigned int, but the call sites use
unsigned long, which is a pointless exercise. Fix the call sites and
replace 'unsigned' with unsinged 'int' while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.236250416@linutronix.de
All VDSO clock sources are TSC based and use CLOCKSOURCE_MASK(64). There is
no point in masking with all FF. Get rid of it and enforce the mask in the
sanity checker.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.151963007@linutronix.de
Runtime validate the VCLOCK_MODE in clocksource::archdata and disable
VCLOCK if invalid, which disables the VDSO but keeps the system running.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130707.069167446@linutronix.de