Fixes the following sparse warning:
net/sched/sch_generic.c:944:6: warning:
symbol 'qdisc_free_cb' was not declared. Should it be static?
Fixes: 3a7d0d07a3 ("net: sched: extend Qdisc with rcu")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe r4.0, sec 7.5.1.1.4 defines a new bit in the Status Register:
Immediate Readiness – This optional bit, when Set, indicates the Function
is guaranteed to be ready to successfully complete valid configuration
accesses at any time following any reset that the host is capable of
issuing Configuration Requests to this Function.
When this bit is Set, for accesses to this Function, software is exempt
from all requirements to delay configuration accesses following any type
of reset, including but not limited to the timing requirements defined in
Section 6.6.
This means that all delays after a Conventional or Function Reset can be
skipped.
This patch reads such bit and caches its value in a flag inside struct
pci_dev to be checked later if we should delay or can skip delays after a
reset. While at that, also move the explicit msleep(100) call from
pcie_flr() and pci_af_flr() to pci_dev_wait().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bhelgaas: rename PCI_STATUS_IMMEDIATE to PCI_STATUS_IMM_READY]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We apply a smoothing to the scale changes in order to keep sawtoothy
behavior from occurring. However our window for checking if we've
missed our target can sometimes be lower than the smoothing interval
(500ms), especially on faster drives like ssd's. In order to deal with
this keep track of the running tally of the previous intervals that we
threw away because we had already done a scale event recently.
This is needed for the ssd case as these low latency drives will have
bursts of latency, and if it happens to be ok for the window that
directly follows the opening of the scale window we could unthrottle
when previous windows we were missing our target.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We use an average latency approach for determining if we're missing our
latency target. This works well for rotational storage where we have
generally consistent latencies, but for ssd's and other low latency
devices you have more of a spikey behavior, which means we often won't
throttle misbehaving groups because a lot of IO completes at drastically
faster times than our latency target. Instead keep track of how many
IO's miss our target and how many IO's are done in our time window. If
the p(90) latency is above our target then we know we need to throttle.
With this change in place we are seeing the same throttling behavior
with our testcase on ssd's as we see with rotational drives.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is logic to keep cgroups that haven't done a lot of IO in the most
recent scale window from being punished for over-active higher priority
groups. However for things like ssd's where the windows are pretty
short we'll end up with small numbers of samples, so 5% of samples will
come out to 0 if there aren't enough. Make the floor 1 sample to keep
us from improperly bailing out of scaling down.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hitting the case where blk_queue_depth() returned 1 uncovered the fact
that iolatency doesn't actually handle this case properly, it simply
doesn't scale down anybody. For this case we should go straight into
applying the time delay, which we weren't doing. Since we already limit
the floor at 1 request this if statement is not needed, and this allows
us to set our depth to 1 which allows us to apply the delay if needed.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We were using blk_queue_depth() assuming that it would return
nr_requests, but we hit a case in production on drives that had to have
NCQ turned off in order for them to not shit the bed which resulted in a
qd of 1, even though the nr_requests was much larger. iolatency really
only cares about requests we are allowed to queue up, as any io that
get's onto the request list is going to be serviced soonish, so we want
to be throttling before the bio gets onto the request list. To make
iolatency work as expected, simply use q->nr_requests instead of
blk_queue_depth() as that is what we actually care about.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This test adds an fdb entry with the sticky flag and sends traffic from
a different port with the same mac as a source address expecting the entry
to not change ports if the flag is operating correctly.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to explicitly zero is_sticky when creating a new fdb, otherwise
we might get a stale value for a new entry.
Fixes: 435f2e7cc0 ("net: bridge: add support for sticky fdb entries")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* two new spectre-v1 mitigations in nl80211
* TX status fix in general, and mesh in particular
* powersave vs. offchannel fix
* regulatory initialization fix
* fix for a queue hang due to a bad return value
* allocate TXQs for active monitor interfaces, fixing my
earlier patch to avoid unnecessary allocations where I
missed this case needed them
* fix TDLS data frames priority assignment
* fix scan results processing to take into account duplicate
channel numbers (over different operating classes, but we
don't necessarily know the operating class)
* various hwsim fixes for radio destruction and new radio
announcement messages
* remove an extraneous kernel-doc line
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlusvBUACgkQB8qZga/f
l8RGlg/+LeQVHh62PJcawXxxa7UyxBhapgkrXC/Np8hnd39xUL41SNMz2wIt7snu
W2iY+5DOJZ9UyrVL70hMZ26lOLonoafhRdH0utQX3U13iD+3g35Xrps/NETlZxcy
QftxstUeh9ojdKcOmTtOlHt3PkLCSVa6kS6TsfFGXnMeAgpbmBlPpJQhsCf1x2M4
ZBUn92sdQu4c8goFUIj8XhgccJbIuAi9pOgQDOE7EXTrxq+Y1SBl1qYCH1bjOkPd
O5lvV74Sr1SPWfWE6IgUPyRGTEjrImfKm5M/1aegcQ6KRk3LZYtNfjxcrRQg9uzA
5FMO6zNpu5EEyspS18F1F/9cLo5meqVW4A+Qr6FQ8NwAJ7O31CerEFHUwSHtLfgL
EjMuWfoKbFaj8YOeShdR3N305Eitc5/uF4m+FVee1tig3GnmUEFzNB0ngMqwFmed
esHbLlVPDYqoKzN7wZYFB/rTDcQxtcHX8m1SQfMqRgmLVkfKS1AUHk0kql++pivW
ZzNlePz3gzacurTeU8FqktxXQfdB8CRyeLqKapTE+3mY9HgYZxnKz1wV6lyoMGiM
yfn0FjsRaYgNXeB0hJ8J6w/+DJWRwahVyas1QbCZKjcY9A67LRpiRlUwEGVGtu/j
OaNWDFLPVkERYNg/7qhMym5h0RyvcBumYd9TVzwupnTiV3T1ScY=
=ySdv
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
More patches than I'd like perhaps, but each seems reasonable:
* two new spectre-v1 mitigations in nl80211
* TX status fix in general, and mesh in particular
* powersave vs. offchannel fix
* regulatory initialization fix
* fix for a queue hang due to a bad return value
* allocate TXQs for active monitor interfaces, fixing my
earlier patch to avoid unnecessary allocations where I
missed this case needed them
* fix TDLS data frames priority assignment
* fix scan results processing to take into account duplicate
channel numbers (over different operating classes, but we
don't necessarily know the operating class)
* various hwsim fixes for radio destruction and new radio
announcement messages
* remove an extraneous kernel-doc line
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids BUG_ON when f2fs_get_meta_page_nofail got EIO during
xfstests/generic/475.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The structure shared between driver and the management FW (mfw) differ in
sizes. This would lead to issues when driver try to access the structure
members which are not-aligned with the mfw copy e.g., data_ptr usage in the
case of mfw_tlv request.
Align the driver structure with mfw copy, add reserved field(s) to driver
structure for the members not used by the driver.
Fixes: dd006921d6 ("qed: Add MFW interfaces for TLV request support.)
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Salil Mehta says:
====================
Cleanups, minor additions & fixes for HNS3 driver
This patch-set contains cleans-ups, minor changes and fixes to the HNS3 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_tm_schd_info_update should return an error when num_tc is greater
than alloc_tqps.
This patch changes the return type of hnae3_register_ae_algo from void
to int.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.
This patch fixes it by not returning when the setting fails.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.
This patch fixes it by rounding up packet size when calculating.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds serdes parallel inner loopback support for self test.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, our implementation of mac loopback is the implementation of app
loopback now. Current name is wrong. This patch renames mac loopback to
app loopback.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our loop mode includes mac loop, serdes loop and phy loop. Not all of them
are related with mac. This patch corrects their names.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra mac address of pause param is used to do double check
for pause frame. This patch set it to HW. If we do not do that,
pfc pause frame will be transferred protocol stack when normal
flow control mode is enabled.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sctp checksum offload.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ameen Rahman <Ameen.Rahman@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I haven't been doing reviews only but not active development on bridge
code for several years. Roopa and Nikolay have been doing most of
the new features and have agreed to take over as new co-maintainers.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
When there is an error in either ath3k_load_firmware() or
ath3k_load_fwfile(), the inlined function ath3k_log_failed_loading() is
called receiving the error returned and both the block size requested to
load and the size actually loaded. These values are printed in an error
message using the macro BT_ERR.
This patch changes that function in order to print the variable "count"
as well, to show more information when a failing firmware loading
operation happens. The calls to the older function were changed to the
new one.
This event is being monitored in a laptop with an adapter which
identifies itself as 0cf3:0036, where sometimes there are errors in the
firmware loading process.
Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-09-26
please apply two qeth patches for -net. The first is a trivial cleanup
required for patch #2 by Jean, which fixes a potential endless loop.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions qeth_get_ipa_msg and qeth_get_ipa_cmd_name are modifying
the last member of global arrays without any locking that I can see.
If two instances of either function are running at the same time,
it could cause a race ultimately leading to an array overrun (the
contents of the last entry of the array is the only guarantee that
the loop will ever stop).
Performing the lookups without modifying the arrays is admittedly
slower (two comparisons per iteration instead of one) but these
are operations which are rare (should only be needed in error
cases or when debugging, not during successful operation) and it
seems still less costly than introducing a mutex to protect the
arrays in question.
As a side bonus, it allows us to declare both arrays as const data.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Cc: Ursula Braun <ubraun@linux.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the common code ARRAY_SIZE macro instead of a private implementation.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bit positions of PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE and
PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE in CTRL_CORE_SMA_SW_7 are
incorrectly documented in the TRM. In fact, the bit positions are
swapped. Update the DT bindings for PCIe EP to reflect the same.
Fixes: d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:
drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
static int unimac_mdio_suspend(struct device *d)
Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.
Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out that the length of the temporary buffer may not be sufficient for
large numbers of leds:
drivers/net/phy/mscc.c: In function 'vsc85xx_probe':
drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=]
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~
drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
While we can make a reasonable assumption that the number of LEDs is small,
the cost of making the buffer a little bigger is insignificant as well.
Fixes: 11bfdabb7f ("net: phy: mscc: factorize code for LEDs mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the only users of the oldadv/newadv variables
accidentally left the now-unused declarations behind:
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam':
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable]
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable]
Fixes: 70814e819c ("net: ethernet: Add helper for set_pauseparam for Asym Pause")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning:
symbol 'aq_fw1x_set_power' was not declared. Should it be static?
Fixes: a0da96c08c ("net: aquantia: implement WOL support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/tls/tls_sw.c:655:16: warning:
symbol 'get_rec' was not declared. Should it be static?
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/core/gen_stats.c:166:1: warning:
symbol '___gnet_stats_copy_basic' was not declared. Should it be static?
Fixes: 5e111210a4 ("net/core: Add new basic hardware counter")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_delete_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:354:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_join_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:463:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
Since commit 1eec2437d1 ("qed: Make OOO archipelagos into an array"),
'p_archipelago' is no longer in use.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
netlink: nested policy validation
This adds nested policy validation, which lets you specify the
nested attribute type, e.g. NLA_NESTED with sub-policy, or the
new NLA_NESTED_ARRAY with sub-sub-policy.
Changes in v2:
* move setting the bad attr pointer/message into validate_nla()
* remove the recursion patch since that's no longer needed
* simply skip the generic bad attr pointer/message setting in
case of nested nla_validate() failing since that could fail
only due to validate_nla() failing inside, which already sets
the extack information
Changes in v3:
* fix NLA_REJECT to have an error message if none is in policy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes nested netlink attributes are just used as arrays, with
the nla_type() of each not being used; we have this in nl80211 and
e.g. NFTA_SET_ELEM_LIST_ELEMENTS.
Add the ability to validate this type of message directly in the
policy, by adding the type NLA_NESTED_ARRAY which does exactly
this: require a first level of nesting but ignore the attribute
type, and then inside each require a second level of nested and
validate those attributes against a given policy (if present).
Note that some nested array types actually require that all of
the entries have the same index, this is possible to express in
a nested policy already, apart from the validation that only the
one allowed type is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a validation_data pointer, and the len field in
the policy is unused for NLA_NESTED, we can allow using them both
to have nested validation. This can be nice in code, although we
still have to use nla_parse_nested() or similar which would also
take a policy; however, it also serves as documentation in the
policy without requiring a look at the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the code between nla_parse() which sets the bad
attribute pointer and an error message, and nla_validate()
which only sets the bad attribute pointer.
It also cleans up the code for NLA_REJECT and paves the way
for nested policy validation, as it will allow us to easily
skip setting the "generic" message without any extra args
like the **error_msg now, just passing the extack through is
now enough.
While at it, remove the unnecessary label in nla_parse().
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The validation data is only used within the policy that
should usually already be const, and isn't changed in any
code that uses it. Therefore, make the validation_data
pointer const.
While at it, remove the duplicate variable in the bitfield
validation that I'd otherwise have to change to const.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This isn't used anywhere, so we might as well get rid of it.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 3.3 has been retired for a while, use PTRS_PER_PGD and remove the
asm-offsets.h inclusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20814/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org