Re-organize things so the state variable is not read unlocked. The first
attempt to go directly from ADDR_BOUND immediately tells us if the ID is
already bound, if we can't do that then the attempt inside
rdma_bind_addr() to go from IDLE to ADDR_BOUND confirms the ID needs
binding.
Link: https://lore.kernel.org/r/20200902081122.745412-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It is currently a bit confusing, but the design is if the handler_mutex
is held, and the state is in RDMA_CM_CONNECT, then the state cannot leave
RDMA_CM_CONNECT without also serializing with the handler_mutex.
Make this clearer by adding a direct assertion, fixing the usage in
rdma_connect and generally using READ_ONCE to read the state value.
Link: https://lore.kernel.org/r/20200902081122.745412-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
- Add compatible strings for three more Broadcom STB chips: 7278, 7216,
7211 (STB version of RPi4).
- Add new property 'brcm,scb-sizes'.
- Add new property 'resets'.
- Add new property 'reset-names' for 7216 only.
- Allow 'ranges' and 'dma-ranges' to have more than one item and update
the example to show this.
Link: https://lore.kernel.org/r/20200911175232.19016-3-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The K3 AM65x and J721E SoCs have the next generation of the PRU-ICSS IP,
commonly called ICSSG. The PRUSS INTC present within the ICSSG supports
more System Events (160 vs 64), more Interrupt Channels and Host Interrupts
(20 vs 10) compared to the previous generation PRUSS INTC instances. The
first 2 and the last 10 of these host interrupt lines are used by the
PRU and other auxiliary cores and sub-modules within the ICSSG, with 8
host interrupts connected to MPU. The host interrupts 5, 6, 7 are also
connected to the other ICSSG instances within the SoC and can be
partitioned as per system integration through the board dts files.
Enhance the PRUSS INTC driver to add support for this ICSSG INTC
instance.
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
This implements the irq_get_irqchip_state and irq_set_irqchip_state
callbacks for the TI PRUSS INTC driver. The set callback can be used
by drivers to "kick" a PRU by injecting a PRU system event.
Co-developed-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The PRUSS INTC has a fixed number of output interrupt lines that are
connected to a number of processors or other PRUSS instances or other
devices (like DMA) on the SoC. The output interrupt lines 2 through 9
are usually connected to the main Arm host processor and are referred
to as host interrupts 0 through 7 from ARM/MPU perspective.
All of these 8 host interrupts are not always exclusively connected
to the Arm interrupt controller. Some SoCs have some interrupt lines
not connected to the Arm interrupt controller at all, while a few others
have the interrupt lines connected to multiple processors in which they
need to be partitioned as per SoC integration needs. For example, AM437x
and 66AK2G SoCs have 2 PRUSS instances each and have the host interrupt 5
connected to the other PRUSS, while AM335x has host interrupt 0 shared
between MPU and TSC_ADC and host interrupts 6 & 7 shared between MPU and
a DMA controller.
Add logic to the PRUSS INTC driver to ignore both these shared and
invalid interrupts.
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The Programmable Real-Time Unit Subsystem (PRUSS) contains a local
interrupt controller (INTC) that can handle various system input events
and post interrupts back to the device-level initiators. The INTC can
support upto 64 input events with individual control configuration and
hardware prioritization. These events are mapped onto 10 output interrupt
lines through two levels of many-to-one mapping support. Different
interrupt lines are routed to the individual PRU cores or to the host
CPU, or to other devices on the SoC. Some of these events are sourced
from peripherals or other sub-modules within that PRUSS, while a few
others are sourced from SoC-level peripherals/devices.
The PRUSS INTC platform driver manages this PRUSS interrupt controller
and implements an irqchip driver to provide a Linux standard way for
the PRU client users to enable/disable/ack/re-trigger a PRUSS system
event. The system events to interrupt channels and output interrupts
relies on the mapping configuration provided either through the PRU
firmware blob (for interrupts routed to PRU cores) or via the PRU
application's device tree node (for interrupt routed to the main CPU).
In the first case the mappings will be programmed on PRU remoteproc
driver demand (via irq_create_fwspec_mapping) during the boot of a PRU
core and cleaned up after the PRU core is stopped.
Reference counting is used to allow multiple system events to share a
single channel and to allow multiple channels to share a single host
event.
The PRUSS INTC module is reference counted during the interrupt
setup phase through the irqchip's irq_request_resources() and
irq_release_resources() ops. This restricts the module from being
removed as long as there are active interrupt users.
The driver currently supports and can be built for OMAP architecture
based AM335x, AM437x and AM57xx SoCs; Keystone2 architecture based
66AK2G SoCs and Davinci architecture based OMAP-L13x/AM18x/DA850 SoCs.
All of these SoCs support 64 system events, 10 interrupt channels and
10 output interrupt lines per PRUSS INTC with a few SoC integration
differences.
NOTE:
Each PRU-ICSS's INTC on AM57xx SoCs is preceded by a Crossbar that
enables multiple external events to be routed to a specific number
of input interrupt events. Any non-default external interrupt event
directed towards PRUSS needs this crossbar to be setup properly.
Co-developed-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Andrew F. Davis <afd@ti.com>
Co-developed-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: David Lechner <david@lechnology.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The Programmable Real-Time Unit and Industrial Communication Subsystem
(PRU-ICSS or simply PRUSS) contains an interrupt controller (INTC) that
can handle various system input events and post interrupts back to the
device-level initiators. The INTC can support up to 64 input events on
most SoCs with individual control configuration and h/w prioritization.
These events are mapped onto 10 output interrupt lines through two levels
of many-to-one mapping support. Different interrupt lines are routed to
the individual PRU cores or to the host CPU or to other PRUSS instances.
The K3 AM65x and J721E SoCs have the next generation of the PRU-ICSS IP,
commonly called ICSSG. The ICSSG interrupt controller on K3 SoCs provide
a higher number of host interrupts (20 vs 10) and can handle an increased
number of input events (160 vs 64) from various SoC interrupt sources.
Add the bindings document for these interrupt controllers on all the
applicable SoCs. It covers the OMAP architecture SoCs - AM33xx, AM437x
and AM57xx; the Keystone 2 architecture based 66AK2G SoC; the Davinci
architecture based OMAPL138 SoCs, and the K3 architecture based AM65x
and J721E SoCs.
Co-developed-by: Andrew F. Davis <afd@ti.com>
Co-developed-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Running the eBPF test_verifier leads to random errors looking like this:
[ 6525.735488] Unexpected kernel BRK exception at EL1
[ 6525.735502] Internal error: ptrace BRK handler: f2000100 [#1] SMP
[ 6525.741609] Modules linked in: nls_utf8 cifs libdes libarc4 dns_resolver fscache binfmt_misc nls_ascii nls_cp437 vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher ghash_ce gf128mul efi_pstore sha2_ce sha256_arm64 sha1_ce evdev efivars efivarfs ip_tables x_tables autofs4 btrfs blake2b_generic xor xor_neon zstd_compress raid6_pq libcrc32c crc32c_generic ahci xhci_pci libahci xhci_hcd igb libata i2c_algo_bit nvme realtek usbcore nvme_core scsi_mod t10_pi netsec mdio_devres of_mdio gpio_keys fixed_phy libphy gpio_mb86s7x
[ 6525.787760] CPU: 3 PID: 7881 Comm: test_verifier Tainted: G W 5.9.0-rc1+ #47
[ 6525.796111] Hardware name: Socionext SynQuacer E-series DeveloperBox, BIOS build #1 Jun 6 2020
[ 6525.804812] pstate: 20000005 (nzCv daif -PAN -UAO BTYPE=--)
[ 6525.810390] pc : bpf_prog_c3d01833289b6311_F+0xc8/0x9f4
[ 6525.815613] lr : bpf_prog_d53bb52e3f4483f9_F+0x38/0xc8c
[ 6525.820832] sp : ffff8000130cbb80
[ 6525.824141] x29: ffff8000130cbbb0 x28: 0000000000000000
[ 6525.829451] x27: 000005ef6fcbf39b x26: 0000000000000000
[ 6525.834759] x25: ffff8000130cbb80 x24: ffff800011dc7038
[ 6525.840067] x23: ffff8000130cbd00 x22: ffff0008f624d080
[ 6525.845375] x21: 0000000000000001 x20: ffff800011dc7000
[ 6525.850682] x19: 0000000000000000 x18: 0000000000000000
[ 6525.855990] x17: 0000000000000000 x16: 0000000000000000
[ 6525.861298] x15: 0000000000000000 x14: 0000000000000000
[ 6525.866606] x13: 0000000000000000 x12: 0000000000000000
[ 6525.871913] x11: 0000000000000001 x10: ffff8000000a660c
[ 6525.877220] x9 : ffff800010951810 x8 : ffff8000130cbc38
[ 6525.882528] x7 : 0000000000000000 x6 : 0000009864cfa881
[ 6525.887836] x5 : 00ffffffffffffff x4 : 002880ba1a0b3e9f
[ 6525.893144] x3 : 0000000000000018 x2 : ffff8000000a4374
[ 6525.898452] x1 : 000000000000000a x0 : 0000000000000009
[ 6525.903760] Call trace:
[ 6525.906202] bpf_prog_c3d01833289b6311_F+0xc8/0x9f4
[ 6525.911076] bpf_prog_d53bb52e3f4483f9_F+0x38/0xc8c
[ 6525.915957] bpf_dispatcher_xdp_func+0x14/0x20
[ 6525.920398] bpf_test_run+0x70/0x1b0
[ 6525.923969] bpf_prog_test_run_xdp+0xec/0x190
[ 6525.928326] __do_sys_bpf+0xc88/0x1b28
[ 6525.932072] __arm64_sys_bpf+0x24/0x30
[ 6525.935820] el0_svc_common.constprop.0+0x70/0x168
[ 6525.940607] do_el0_svc+0x28/0x88
[ 6525.943920] el0_sync_handler+0x88/0x190
[ 6525.947838] el0_sync+0x140/0x180
[ 6525.951154] Code: d4202000 d4202000 d4202000 d4202000 (d4202000)
[ 6525.957249] ---[ end trace cecc3f93b14927e2 ]---
The reason is the offset[] creation and later usage, while building
the eBPF body. The code currently omits the first instruction, since
build_insn() will increase our ctx->idx before saving it.
That was fine up until bounded eBPF loops were introduced. After that
introduction, offset[0] must be the offset of the end of prologue which
is the start of the 1st insn while, offset[n] holds the
offset of the end of n-th insn.
When "taken loop with back jump to 1st insn" test runs, it will
eventually call bpf2a64_offset(-1, 2, ctx). Since negative indexing is
permitted, the current outcome depends on the value stored in
ctx->offset[-1], which has nothing to do with our array.
If the value happens to be 0 the tests will work. If not this error
triggers.
commit 7c2e988f40 ("bpf: fix x64 JIT code generation for jmp to 1st insn")
fixed an indentical bug on x86 when eBPF bounded loops were introduced.
So let's fix it by creating the ctx->offset[] differently. Track the
beginning of instruction and account for the extra instruction while
calculating the arm instruction offsets.
Fixes: 2589726d12 ("bpf: introduce bounded loops")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Jiri Olsa <jolsa@kernel.org>
Co-developed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Co-developed-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200917084925.177348-1-ilias.apalodimas@linaro.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This code should use "vma[1]" instead of "vma". The "vma" variable is a
valid pointer.
Fixes: 6b05030496 ("drm/i915: Convert i915_gem_object/client_blt.c to use ww locking as well, v2.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200911075243.GG12635@kadam
Currently Tegra DRM driver manually manages display panel, but this
management could be moved out into DRM core if we'll wrap panel into
DRM bridge. This patch wraps RGB panel into a DRM bridge and removes
manual handling of the panel from the RGB output code.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Newer Tegra device-trees will specify a video output graph, which involves
LVDS encoder bridge. This patch adds support for the LVDS encoder bridge
to the RGB output, allowing us to model the display hardware properly.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Newer Tegra device-trees will specify a video output graph which involves
a bridge. This patch adds initial support for the DRM bridges to the Tegra
DRM output.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OF node should be put before returning error in tegra_output_probe(),
otherwise node's refcount will be leaked.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the of_get_i2c_adapter_by_node(), which is similar to the existing
call to of_find_i2c_adapter_by_node() except that it also takes a
reference to the owner module of the I2C adapter. In order to properly
balance this out, call i2c_put_adapter() to release the reference to the
I2C adapter and its owner module.
For the special case where the DDC comes from the DPAUX, care must be
taken to perform the same steps (i.e. get_device() and module_get()) so
that the reference counts are all balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's possible for a GPIO chip to not have a parent device (whose
properties we inspect for 'gpio-line-names'). In this case we should
simply return from devprop_gpiochip_set_names(). Add an appropriate
check for this use-case.
Fixes: 7cba1a4d5e ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the CPU clock registration two parent clocks are required, these
are now being passed as struct clk_hw pointers, rather than by the
global scope names. That allows us to avoid __clk_lookup() calls
and simplifies a bit the CPU clock registration function.
While at it drop unneeded extern keyword in the function declaration.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20200826171529.23618-3-s.nawrocki@samsung.com
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use non-zero clock IDs in definitions of the CPU parent clocks
for exynos5420, exynos5250 SoCs. This will allow us to reference
the parent clocks directly in the driver by cached struct clk_hw
pointers, rather than doing clk lookup by name.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20200826171529.23618-2-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add clock ID definitions for the CPU parent clocks for SoCs
which don't have such definitions yet. This will allow us to
reference the parent clocks directly by cached struct clk_hw
pointers in the clock provider, rather than doing clk lookup
by name.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200826171529.23618-1-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds a clk ID to the mout_sw_aclk_g3d clk definition so related
clk pointer gets cached in the driver's private data and can be used
later instead of a __clk_lookup() call.
With that we have all clocks used in the clk_prepare_enable() calls in the
clk provider init callback cached in clk_data.hws[] and we can reference
the clk pointers directly rather than using __clk_lookup() with global names.
Link: https://lore.kernel.org/r/20200811151251.31613-2-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds ID for the mout_sw_aclk_g3d (SW_CLKMUX_ACLK_G3D) clock,
mostly for internal use in the CMU driver. It will allow to avoid the
__clk_lookup() call when setting up the clock during the clock provider
initialization.
Link: https://lore.kernel.org/r/20200811151251.31613-1-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The introduced line event handling ABI in the commit
61f922db72 ("gpio: userspace ABI for reading GPIO line events")
missed the fact that 64-bit kernel may serve for 32-bit applications.
In such case the very first check in the lineevent_read() will fail
due to alignment differences.
To workaround this introduce lineevent_get_size() helper which returns actual
size of the structure in user space.
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
As warned by smatch:
drivers/media/test-drivers/vidtv/vidtv_psi.c:93 vidtv_psi_update_version_num() warn: impossible condition '(h->version > 32) => (0-31 > 32)'
h_version is declared as:
u8 version:5;
Meaning that its value ranges from 0 to 31. Incrementing 31 on such
data will overflow to zero, as expected.
So, just drop the uneeded overflow check.
While here, use "foo++" instead of "++foo", as this is a much
more common pattern.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to use u64 over there. In a matter of fact,
the div is not even needed, as it is multiplying by 1000 and
dividing by 1000.
So, simplify the logic.
While here, constrain the buffer size to a certain range
(between the current value and 10 times it)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following error for builds on 32bit architectures:
ERROR: modpost: "__udivdi3"
[drivers/media/test-drivers/vidtv/dvb-vidtv-bridge.ko] undefined!
Which is due to 64bit divisions that did not go through the helpers
in linux/math64.h
As vidtv_mux_check_mux_rate was not operational in its current form,
drop the entire function while it is not fixed properly.
For now, call vidtv_mux_pad_with_nulls with a constant number of packets
to avoid warnings due to unused functions when building this driver.
The 64bit division used in the s302m is not needed, remove them and use
a fixed number of frames and a constant PTS increment instead.
Fixes: f90cf6079b ("media: vidtv: add a bridge driver")
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Keep playing a single tone is not too nice, and prevents
checking some weird things.
So, instead, implement a simple tone generator, changing
the code to play a public domain song (5th Symphony of
Beethoven), using sinusoidal waves.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A typical digital TV stream has errors that are corrected
by Viterbi. While the error rate after Viterbi is usually
zero, with good signals, there are some chances of getting
random errors before that, which are auto-corrected by
the error code algorithm.
Add a poor guy's implementation that would show some
noise at the pre-BER part of the demod.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The virtual driver has now a minimal set of frequencies for a
single transponder to be found by each DVB standard.
Document it, and update related information about the
simulated LNBf.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Satellite setups are different than terrestrial and cable ones,
as there is a device coupled at the antenna, called LNBf, which
converts the frequency from a GHz range at C-Band or Ku-Band
into an intermediate frequency at S-Band (ranging up to ~2GHz).
There are several different models of LNBf, with different
IF conversions, but the most common nowadays is called
Universal LNBf. Those got their frequency ranges extended in the
past, when Astra 19.2E sattellite was launched.
The universal LNBf has two local oscilators:
- 9.75 GHz
- 10.6 GHz
The first one is used when the frequency is between 10.7 GHz
up to 11.7 GHz. The second one is for frequencies between
11.7 GHz to 12.75 GHz.
With that, the IF signal will be at 950 MHz to 2,150 MHz range.
Add support for doing the above math, and make clear that
the frequencies expected by the driver should be at Ku-Band
range.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Unexport ttm_check_under_lowerlimit.
Make ttm_bo_acc_size static and unexport it.
Remove ttm_get_kernel_zone_memory_size.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/390515/
Grab a reference to the transport driver to ensure it can't be unloaded
while a passthrough controller is active.
Fixes: c1fef73f79 ("nvmet: add passthru code to process commands")
Reported-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Updates to the UEFI 2.8 Memory Error Record allow splitting the bank field
into bank address and bank group, and using the last 3 bits of the extended
field as a chip identifier.
When needed, print correct version of bank field, bank group, and chip
identification.
Based on UEFI 2.8 Table 299. Memory Error Record.
Signed-off-by: Alex Kluver <alex.kluver@hpe.com>
Reviewed-by: Russ Anderson <russ.anderson@hpe.com>
Reviewed-by: Kyle Meyer <kyle.meyer@hpe.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20200819143544.155096-3-alex.kluver@hpe.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Memory errors could be printed with incorrect row values since the DIMM
size has outgrown the 16 bit row field in the CPER structure. UEFI
Specification Version 2.8 has increased the size of row by allowing it to
use the first 2 bits from a previously reserved space within the structure.
When needed, add the extension bits to the row value printed.
Based on UEFI 2.8 Table 299. Memory Error Record
Signed-off-by: Alex Kluver <alex.kluver@hpe.com>
Tested-by: Russ Anderson <russ.anderson@hpe.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Kyle Meyer <kyle.meyer@hpe.com>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20200819143544.155096-2-alex.kluver@hpe.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
At least some versions of Dell EFI firmware pass the entire
EFI_LOAD_OPTION descriptor, rather than just the OptionalData part, to
the loaded image. This was verified with firmware revision 2.15.0 on a
Dell Precision T3620 by Jacobo Pantoja.
To handle this, add a quirk to check if the options look like a valid
EFI_LOAD_OPTION descriptor, and if so, use the OptionalData part as the
command line.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Reported-by: Jacobo Pantoja <jacobopantoja@gmail.com>
Link: https://lore.kernel.org/linux-efi/20200907170021.GA2284449@rani.riverdale.lan/
Link: https://lore.kernel.org/r/20200914213535.933454-2-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
There is one overlooked situation under which a driver must not do IO to
allocate memory. You cannot do that while disconnecting a device. A
device being disconnected is no longer functional in most cases, yet IO
may fail only when the handler runs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916191544.5104-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please pull a set of fixes for various DRM drivers that finally resolve
incorrect usage of the scatterlists (struct sg_table nents and orig_nents
entries), what causes issues when IOMMU is used.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910080505.24456-1-m.szyprowski@samsung.com
[Why]
DTM topology updates happens by default now. This results in DTM
warnings when hdcp is not even being enabled. This spams the dmesg
and doesn't effect normal display functionality so it is better to log it
using DRM_DEBUG_KMS()
[How]
Change the DRM_WARN() to DRM_DEBUG_KMS()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The firmware provided via MODULE_FIRMWARE appears in the
module information. External tools(eg. dracut) may use the
list of fw files to include them as appropriate in an initramfs,
thus missing declaration will lead to request firmware failure
in boot time.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tianci Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
