A clk driver can be a module but the gdsc code is in the common module.
Export this symbol so that allmodconfig builds keep working.
Cc: Jonathan Marek <jonathan@marek.ca>
Fixes: 0638226dd0 ("clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200724094025.3261266-1-sboyd@kernel.org
Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-18-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL).
For these, split the PLL clock in two: fractional clock and
divider clock. In case PLLs supports multiple outputs (since these
outputs are dividers (with different settings) sharing the same
fractional part), it will register one fractional clock and multiple
divider clocks (dividers sharing the fractional clock).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some peripheral clocks on SAMA7G5 supports requesting parent to change
its rate (image related clocks: csi, csi2dc, isc). Add support
so that if registered with this option the clock rate to be
requested from parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pass the ID of changeable parent at registration. This will allow
the scalability of this clock driver with regards to the changeable
parent ID for versions of this IP where changeable parent is not the
last one in the parents list (e.g. SAMA7G5). With this the clock flags
are set to zero in case we have no changeable parent. Also in
clk_generated_best_diff() the *best_diff variable is check against
tmp_diff variable using ">=" operator instead of ">" so that in case
the requested frequency could be obtained using fix parents + gck
dividers but the clock also supports changeable parent to be able
to force the usage of the changeable parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In commit a436c2a447 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
__clk_determine_rate() may return error. Skip the current step
in case of error.
Fixes: 1a1a36d72e ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.
Use device_node_to_regmap to resolve this as it looks up the regmap in
the same list but doesn't care about the clocks. This issue is detected
by lockdep when booting the sama5d3 with a device tree containing the
new clk bindings.
This fix already happened in 6956eb33ab ("clk: at91: fix possible
deadlock") for the drivers that had been migrated to the new clk binding
back then. This does the same for the new drivers as well.
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200703073236.23923-1-a.fatoum@pengutronix.de
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
1.Add "PRID_COMP_INGENIC_13" and "PRID_IMP_XBURST2" for X2000.
2.Add X2000 system type for cat /proc/cpuinfo to give out X2000.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
if of_find_device_by_node() succeed, dwc3_octeon_device_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 93e502b3c2 ("MIPS: OCTEON: Platform support for OCTEON III USB controller")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
For test and debug purposes, it's simple enough to enable or disable
clocks from shell. Add a new debugfs file 'clk_prepare_enable' that
calls clk_prepare_enable() when writing "1" and clk_disable_unprepare()
when writing "0".
This can have security implications, so only support it when the code
has been modified to #define CLOCK_ALLOW_WRITE_DEBUGFS.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200630003024.6282-1-mdtipton@codeaurora.org
[sboyd@kernel.org: Reword commit text and remove comment update]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change from 'DIV_ROUND_UP' to 'DIV_ROUND_CLOSEST' when calculating the
clock divisor in the iProc ASIU clock driver to allow to get to the
closest clock rate.
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Link: https://lore.kernel.org/r/20200612225212.124301-1-ray.jui@broadcom.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
paravirt machine was introduced for Cavium's partial virtualization
technology, however, it's host side support and QEMU support never
landed in upstream.
As Cavium was acquired by Marvel and they have no intention to maintain
their MIPS product line, also paravirt is unlikely to be utilized by
community users, it's time to retire it if nobody steps in to maintain
it.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the graphics clock controller found on SM8250
based devices.
This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-12-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SM8150
based devices.
This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-11-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
All gpucc drivers need this, so move it to common code instead of
duplicating it in every gpucc driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-10-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-9-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
After page requests are handled, software must respond to the device
which raised the page request with the result. This is done through
the iommu ops.page_response if the request was reported to outside of
vendor iommu driver through iommu_report_device_fault(). This adds the
VT-d implementation of page_response ops.
Co-developed-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Co-developed-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-12-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A pasid might be bound to a page table from a VM guest via the iommu
ops.sva_bind_gpasid. In this case, when a DMA page fault is detected
on the physical IOMMU, we need to inject the page fault request into
the guest. After the guest completes handling the page fault, a page
response need to be sent back via the iommu ops.page_response().
This adds support to report a page request fault. Any external module
which is interested in handling this fault should regiester a notifier
with iommu_register_device_fault_handler().
Co-developed-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Co-developed-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-11-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There are several places in the code that need to get the pointers of
svm and sdev according to a pasid and device. Add a helper to achieve
this for code consolidation and readability.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It is refactored in two ways:
- Make it global so that it could be used in other files.
- Make bus/devfn optional so that callers could ignore these two returned
values when they only want to get the coresponding iommu pointer.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-9-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For the unlikely use case where multiple aux domains from the same pdev
are attached to a single guest and then bound to a single process
(thus same PASID) within that guest, we cannot easily support this case
by refcounting the number of users. As there is only one SL page table
per PASID while we have multiple aux domains thus multiple SL page tables
for the same PASID.
Extra unbinding guest PASID can happen due to race between normal and
exception cases. Termination of one aux domain may affect others unless
we actively track and switch aux domains to ensure the validity of SL
page tables and TLB states in the shared PASID entry.
Support for sharing second level PGDs across domains can reduce the
complexity but this is not available due to the limitations on VFIO
container architecture. We can revisit this decision once sharing PGDs
are available.
Overall, the complexity and potential glitch do not warrant this unlikely
use case thereby removed by this patch.
Fixes: 56722a4398 ("iommu/vt-d: Add bind guest PASID support")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For guest requested IOTLB invalidation, address and mask are provided as
part of the invalidation data. VT-d HW silently ignores any address bits
below the mask. SW shall also allow such case but give warning if
address does not align with the mask. This patch relax the fault
handling from error to warning and proceed with invalidation request
with the given mask.
Fixes: 6ee1b77ba3 ("iommu/vt-d: Add svm/sva invalidate function")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For guest SVA usage, in order to optimize for less VMEXIT, guest request
of IOTLB flush also includes device TLB.
On the host side, IOMMU driver performs IOTLB and implicit devTLB
invalidation. When PASID-selective granularity is requested by the guest
we need to derive the equivalent address range for devTLB instead of
using the address information in the UAPI data. The reason for that is,
unlike IOTLB flush, devTLB flush does not support PASID-selective
granularity. This is to say, we need to set the following in the PASID
based devTLB invalidation descriptor:
- entire 64 bit range in address ~(0x1 << 63)
- S bit = 1 (VT-d CH 6.5.2.6).
Without this fix, device TLB flush range is not set properly for PASID
selective granularity. This patch also merged devTLB flush code for both
implicit and explicit cases.
Fixes: 6ee1b77ba3 ("iommu/vt-d: Add svm/sva invalidate function")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Address information for device TLB invalidation comes from userspace
when device is directly assigned to a guest with vIOMMU support.
VT-d requires page aligned address. This patch checks and enforce
address to be page aligned, otherwise reserved bits can be set in the
invalidation descriptor. Unrecoverable fault will be reported due to
non-zero value in the reserved bits.
Fixes: 61a06a16e3 ("iommu/vt-d: Support flushing more translation cache types")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8150 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-8-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DevTLB flush can be used for both DMA request with and without PASIDs.
The former uses PASID#0 (RID2PASID), latter uses non-zero PASID for SVA
usage.
This patch adds a check for PASID value such that devTLB flush with
PASID is used for SVA case. This is more efficient in that multiple
PASIDs can be used by a single device, when tearing down a PASID entry
we shall flush only the devTLB specific to a PASID.
Fixes: 6f7db75e1c ("iommu/vt-d: Add second level page table")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Set proper masks to avoid invalid input spillover to reserved bits.
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
These two bindings are almost identical, so combine them into one. This
will make it easier to add the sm8150 and sm8250 gpucc bindings.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-7-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The fixed alpha pll ops only use it for clamping in round_rate, which is
unnecessary. This is consistent with SM8250 GCC not using vco_table.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-6-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
