[ Upstream commit 585e4dc071 ]
Fix rk3288 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding with some reordering
to align with the (new) documentation about
property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cc3a9b4f-076d-4660-b464-615003b6a066@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79978bff2e ]
We identified that the PHYs actually do not work since commit 7da7b84fee
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497f ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c4bf0e4 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb5193 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 090c409457 ]
External clocks should be defined as zero-Hz clocks in the SoC .dtsi,
and overridden in the board .dts when present.
Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal
oscillator present on the APE6-EVM board.
Fixes: a76809a329 ("ARM: shmobile: r8a73a4: Common clock framework DT description")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1692bc8cd465d62168cbf110522ad62a7af3f606.1705315614.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f02b0f0dc2 ]
The dtc interrupt_map warning is off because its dependency,
interrupt_provider, is off by default. Fix all the warnings so it can be
enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fd598e9c ]
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f98643d8da ]
The binding doesn't define interrupts and adding such a definition was
refused because it's unclear how they should ever be used and the
relevant registers are outside the PWM range. So drop them fixing
several dtbs_check warnings like:
arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dtb: pwm@10280030: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pwm/pwm-rockchip.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240129113205.2453029-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d0 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ab7ad6f7 ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b929f587 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c248e53597 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f0 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478 ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882 ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc3 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07e6a553c2 ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property
Subtract 0xfa600000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba2a45a485 ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@11800000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@11800000: missing or empty reg/ranges property
Subtract 0x11800000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 455a4c46e0 ]
As the vendor DTS files were moved to per-vendor subdirs, there no need
to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file.
This makes 32-bit qcom/ dts files closer to arm64 ones.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-8-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eab4f56d3e ]
After more investigation, I've found that it's not the panel driver
config that needs to be modified to invert the data polarity, but
the FIMD config.
Add the missing invert-vclk option that is required to get the display
to work correctly.
Fixes: ee37a457af ("ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240105-tab3-display-fixes-v2-1-904d1207bf6f@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 710dd03464 upstream.
The USB SS PHY interrupt needs to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states.
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de95f13939 upstream.
The USB DP/DM HS PHY interrupts need to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states and to be able to detect disconnect events, which requires
triggering on falling edges.
A recent commit updated the trigger type but failed to change the
interrupt provider as required. This leads to the current Linux driver
failing to probe instead of printing an error during suspend and USB
wakeup not working as intended.
Fixes: d0ec3c4c11 ("ARM: dts: qcom: sdx55: fix USB wakeup interrupt types")
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84228d5e29 upstream.
The kernel hangs for a good 12 seconds without any info being printed to
dmesg, very early in the boot process, if this regulator is not enabled.
Force-enable it to work around this issue, until we know more about the
underlying problem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0ec3c4c11 upstream.
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231120164331.8116-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b76bbf835d upstream.
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfc3c6743d ]
The binding erroneously decreed that the SCMI variants of the ST
evaluation kits are compatible with the non-SCMI variants.
This is not correct, as a kernel or bootloader compatible with the non-SCMI
variant is not necessarily able to function, when direct access
to resources is replaced by having to talk SCMI to the secure monitor.
The binding has been adjusted to reflect thus, so synchronize the device
trees now.
Fixes: 5b7e58313a ("ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554557542e ]
The XOADC is present at the address 0x197 rather than just 197. It
doesn't change a lot (since the driver hardcodes all register
addresses), but the DT should present correct address anyway.
Fixes: c4b70883ee ("ARM: dts: add XOADC and IIO HWMON to APQ8064")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 836d083524 ]
Some mmcc clocks have dsi0pll & dsi0pllbyte as clock parents so we
should provide them in the dt, which I missed in the commit adding the
mdss nodes.
Fixes: d5fb01ad5e ("ARM: dts: qcom: msm8226: Add mdss nodes")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230712-msm8226-dsi-clock-fixup-v1-1-71010b0b89ca@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b6a51aab5 upstream.
With subtle timings changes, we can now sometimes get an external abort on
non-linefetch error booting am3 devices at sysc_reset(). This is because
of a missing reset delay needed for the usb target module.
Looks like we never enabled the delay earlier for am3, although a similar
issue was seen earlier with a similar usb setup for dm814x as described in
commit ebf2441480 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x").
Cc: stable@vger.kernel.org
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e5caee2ba ]
This node can access any part of the L3 configuration registers space,
including CLK1 and CLK2 which are 0x800000 offset. Restore this area
size to include these areas.
Fixes: 7f2659ce65 ("ARM: dts: Move dra7 l3 noc to a separate node")
Signed-off-by: Andrew Davis <afd@ti.com>
Message-ID: <20231113181604.546444-1-afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ef8fc9bc ]
Per root-node.yaml, 'model' is a required property.
Pass it to fix the following dt-schema warning:
imx28-xea.dtb: /: 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 445ae16ac1 ("ARM: dts: imx28: Add DTS description of imx28 based XEA board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d951f8f5f2 ]
Since commit c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
Fixes: c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc761f11af ]
The LED ACT which is included from bcm2711-rpi-4-b doesn't exists
on the Raspberry Pi 400. So the bcm2711-rpi-400.dts tries to
use the delete-node directive in order to remove the complete
node. Unfortunately the usage get broken in commit 1156e3a78b
("ARM: dts: bcm283x: Move ACT LED into separate dtsi")
and now ACT and PWR LED using the same GPIO and this prevent
probing of led-gpios on Raspberry Pi 400:
leds-gpio: probe of leds failed with error -16
So fix the delete-node directive.
Fixes: 1156e3a78b ("ARM: dts: bcm283x: Move ACT LED into separate dtsi")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231118124252.14838-3-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
