[ Upstream commit 41cf11946b ]
Allow autosuspend to be used by xhci plat device. For Qualcomm SoCs,
when in host mode, it is intended that the controller goes to suspend
state to save power and wait for interrupts from connected peripheral
to wake it up. This is particularly used in cases where a HID or Audio
device is connected. In such scenarios, the usb controller can enter
auto suspend and resume action after getting interrupts from the
connected device.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250916120436.3617598-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 368ed48a5e ]
The usbmon binary interface currently truncates captures of large
transfers from higher-speed USB devices. Because a single event capture
is limited to one-fifth of the total buffer size, the current maximum
size of a captured URB is around 240 KiB. This is insufficient when
capturing traffic from modern devices that use transfers of several
hundred kilobytes or more, as truncated URBs can make it impossible for
user-space USB analysis tools like Wireshark to properly defragment and
reassemble higher-level protocol packets in the captured data.
The root cause of this issue is the 1200 KiB BUFF_MAX limit, which has
not been changed since the binary interface was introduced in 2006.
To resolve this issue, this patch increases BUFF_MAX to 64 MiB. The
original comment for BUFF_MAX based the limit's calculation on a
saturated 480 Mbit/s bus. Applying the same logic to a modern USB 3.2
Gen 2×2 20 Gbit/s bus (~2500 MB/s over a 20ms window) indicates the
buffer should be at least 50 MB. The new limit of 64 MiB covers that,
plus a little extra for any overhead.
With this change, both users and developers should now be able to debug
and reverse engineer modern USB devices even when running unmodified
distro kernels.
Please note that this change does not affect the default buffer size. A
larger buffer is only allocated when a user explicitly requests it via
the MON_IOCT_RING_SIZE ioctl, so the change to the maximum buffer size
should not unduly increase memory usage for users that don't
deliberately request a larger buffer.
Link: https://lore.kernel.org/CAO3ALPzdUkmMr0YMrODLeDSLZqNCkWcAP8NumuPHLjNJ8wC1kQ@mail.gmail.com
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/CAO3ALPxU5RzcoueC454L=WZ1qGMfAcnxm+T+p+9D8O9mcrUbCQ@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c5ff5615 ]
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250905094842.1232-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed6f727c57 ]
Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956606bafb ]
This fix is already present in f_ecm.c and was never
propagated to f_ncm.c
When creating multiple NCM ethernet devices
on a composite usb gadget device
each MAC address on the HOST side will be identical.
Having the same MAC on different network interfaces is bad.
This fix updates the MAC address inside the
ncm_strings_defs global during the ncm_bind call.
This ensures each device has a unique MAC.
In f_ecm.c ecm_string_defs is updated in the same way.
The defunct MAC assignment in ncm_alloc has been removed.
Signed-off-by: raub camaioni <raubcameo@gmail.com>
Link: https://lore.kernel.org/r/20250815131358.1047525-1-raubcameo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cfd6f1a7b4 upstream.
A race condition occurs when ffs_func_eps_enable() runs concurrently
with ffs_data_reset(). The ffs_data_clear() called in ffs_data_reset()
sets ffs->epfiles to NULL before resetting ffs->eps_count to 0, leading
to a NULL pointer dereference when accessing epfile->ep in
ffs_func_eps_enable() after successful usb_ep_enable().
The ffs->epfiles pointer is set to NULL in both ffs_data_clear() and
ffs_data_close() functions, and its modification is protected by the
spinlock ffs->eps_lock. And the whole ffs_func_eps_enable() function
is also protected by ffs->eps_lock.
Thus, add NULL pointer handling for ffs->epfiles in the
ffs_func_eps_enable() function to fix issues
Signed-off-by: Owen Gu <guhuinan@xiaomi.com>
Link: https://lore.kernel.org/r/20250915092907.17802-1-guhuinan@xiaomi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3d12ec847 ]
DbC may add 1024 bogus bytes to the beginneing of the receiving endpoint
if DbC hw triggers a STALL event before any Transfer Blocks (TRBs) for
incoming data are queued, but driver handles the event after it queued
the TRBs.
This is possible as xHCI DbC hardware may trigger spurious STALL transfer
events even if endpoint is empty. The STALL event contains a pointer
to the stalled TRB, and "remaining" untransferred data length.
As there are no TRBs queued yet the STALL event will just point to first
TRB position of the empty ring, with '0' bytes remaining untransferred.
DbC driver is polling for events, and may not handle the STALL event
before /dev/ttyDBC0 is opened and incoming data TRBs are queued.
The DbC event handler will now assume the first queued TRB (length 1024)
has stalled with '0' bytes remaining untransferred, and copies the data
This race situation can be practically mitigated by making sure the event
handler handles all pending transfer events when DbC reaches configured
state, and only then create dev/ttyDbC0, and start queueing transfers.
The event handler can this way detect the STALL events on empty rings
and discard them before any transfers are queued.
This does in practice solve the issue, but still leaves a small possible
gap for the race to trigger.
We still need a way to distinguish spurious STALLs on empty rings with '0'
bytes remaing, from actual STALL events with all bytes transmitted.
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cab63934c3 ]
Event polling delay is set to 0 if there are any pending requests in
either rx or tx requests lists. Checking for pending requests does
not work well for "IN" transfers as the tty driver always queues
requests to the list and TRBs to the ring, preparing to receive data
from the host.
This causes unnecessary busylooping and cpu hogging.
Only set the event polling delay to 0 if there are pending tx "write"
transfers, or if it was less than 10ms since last active data transfer
in any direction.
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Fixes: fb18e5bb96 ("xhci: dbc: poll at different rate depending on data transfer activity")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250505125630.561699-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f3d12ec847 ("xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03e3d9c2bd ]
Queue event polling work with 0 delay in case there are pending transfers
queued up. This is part 2 of a 3 part series that roughly triples dbc
performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
First performance improvement patch was commit 31128e7492
("xhci: dbc: add dbgtty request to end of list once it completes")
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f3d12ec847 ("xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de3edd47a1 ]
xhci DbC driver polls the host controller for DbC events at a reduced
rate when DbC is enabled but there are no active data transfers.
Allow users to modify this reduced poll interval via dbc_poll_interval_ms
sysfs entry. Unit is milliseconds and accepted range is 0 to 5000.
Max interval of 5000 ms is selected as it matches the common 5 second
timeout used in usb stack.
Default value is 64 milliseconds.
A long interval is useful when users know there won't be any activity
on systems connected via DbC for long periods, and want to avoid
battery drainage due to unnecessary CPU usage.
Example being Android Debugger (ADB) usage over DbC on ChromeOS systems
running Android Runtime.
[minor changes and rewording -Mathias]
Co-developed-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f3d12ec847 ("xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb18e5bb96 ]
DbC driver starts polling for events immediately when DbC is enabled.
The current polling interval is 1ms, which keeps the CPU busy, impacting
power management even when there are no active data transfers.
Solve this by polling at a slower rate, with a 64ms interval as default
until a transfer request is queued, or if there are still are pending
unhandled transfers at event completion.
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f3d12ec847 ("xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edf1664f32 ]
When DbC is enabled the first port on the xHC host acts as a usb device.
xHC provides the descriptors automatically when the DbC device is
enumerated. Most of the values are hardcoded, but some fields such as
idProduct, idVendor, bcdDevice and bInterfaceProtocol can be modified.
Add sysfs entries that allow userspace to change these.
User can only change them before dbc is enabled, i.e. before writing
"enable" to dbc sysfs file as we don't want these values to change while
device is connected, or during enumeration.
Add documentation for these entries in
Documentation/ABI/testing/sysfs-bus-pci-drivers-xhci_hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f3d12ec847 ("xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47b2116e54 ]
After an bind/unbind cycle, the acm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
gs_free_req+0x30/0x44
acm_bind+0x1b8/0x1f4
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 1f1ba11b64 ("usb gadget: issue notifications from ACM function")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75a5b8d4dd ]
After an bind/unbind cycle, the ncm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
ncm_bind+0x39c/0x3dc
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfb1d99d96 ]
Gadget function drivers often have goto-based error handling in their
bind paths, which can be bug-prone. Refactoring these paths to use
__free() scope-based cleanup is desirable, but currently blocked.
The blocker is that usb_ep_free_request(ep, req) requires two
parameters, while the __free() mechanism can only pass a pointer to the
request itself.
Store an endpoint pointer in the struct usb_request. The pointer is
populated centrally in usb_ep_alloc_request() on every successful
allocation, making the request object self-contained.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Stable-dep-of: 75a5b8d4dd ("usb: gadget: f_ncm: Refactor bind path to use __free()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bbd38fcd2 upstream.
DbC is currently only enabled back if it's in configured state during
suspend.
If system is suspended after DbC is enabled, but before the device is
properly enumerated by the host, then DbC would not be enabled back in
resume.
Always enable DbC back in resume if it's suspended in enabled,
connected, or configured state
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37b9dd0d11 upstream.
Drop the check on the maximum transfer length in Raw Gadget for both
control and non-control transfers.
Limiting the transfer length causes a problem with emulating USB devices
whose full configuration descriptor exceeds PAGE_SIZE in length.
Overall, there does not appear to be any reason to enforce any kind of
transfer length limit on the Raw Gadget side for either control or
non-control transfers, so let's just drop the related check.
Cc: stable <stable@kernel.org>
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://patch.msgid.link/a6024e8eab679043e9b8a5defdb41c4bda62f02b.1761085528.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc2cf4dca upstream.
The list of Huawei LTE modules needing the quirk fixing spurious wakeups
was missing the IDs of the Huawei ME906S module, therefore suspend did not
work.
Cc: stable <stable@kernel.org>
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20251020134304.35079-1-wse@tuxedocomputers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c206324e upstream.
The cdnsp-pci driver uses pcim_enable_device() to enable a PCI device,
which means the device will be automatically disabled on driver detach
through the managed device framework. The manual pci_disable_device()
call in the error path is therefore redundant.
Found via static anlaysis and this is similar to commit 99ca0b57e4
("thermal: intel: int340x: processor: Fix warning during module unload").
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250903141613.2535472-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e40b984b6c ]
The VHCI platform driver aims to forbid entering system suspend when at
least one of the virtual USB ports are bound to an active USB/IP
connection.
However, in some cases, the detection logic doesn't work reliably, i.e.
when all devices attached to the virtual root hub have been already
suspended, leading to a broken suspend state, with unrecoverable resume.
Ensure the virtually attached devices do not enter suspend by setting
the syscore PM flag. Note this is currently limited to the client side
only, since the server side doesn't implement system suspend prevention.
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250902-vhci-hcd-suspend-fix-v3-1-864e4e833559@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fa726e66 ]
This reverts commit 28a76fcc4c.
No actual HW bugs are known where Endpoint Context shows Running state
but Stop Endpoint fails repeatedly with Context State Error and leaves
the endpoint state unchanged. Stop Endpoint retries on Running EPs have
been performed since early 2021 with no such issues reported so far.
Trying to handle this hypothetical case brings a more realistic danger:
if Stop Endpoint fails on an endpoint which hasn't yet started after a
doorbell ring and enough latency occurs before this completion event is
handled, the driver may time out and begin removing cancelled TDs from
a running endpoint, even though one more retry would stop it reliably.
Such high latency is rare but not impossible, and removing TDs from a
running endpoint can cause more damage than not giving back a cancelled
URB (which wasn't happening anyway). So err on the side of caution and
revert to the old policy of always retrying if the EP appears running.
[Remove stable tag as we are dealing with theoretical cases -Mathias]
Fixes: 28a76fcc4c ("usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250917210726.97100-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e271cc0d25 ]
Once the use_os_string flag is set to true for some functions
(e.g. adb/mtp) which need to response the OS string, and then
if we re-bind the ConfigFS gadget to use the other functions
(e.g. hid) which should not to response the OS string, however,
because the use_os_string flag is still true, so the usb gadget
response the OS string descriptor incorrectly, this can cause
the USB device to be unrecognizable on the Windows system.
An example of this as follows:
echo 1 > os_desc/use
ln -s functions/ffs.adb configs/b.1/function0
start adbd
echo "<udc device>" > UDC #succeed
stop adbd
rm configs/b.1/function0
echo 0 > os_desc/use
ln -s functions/hid.gs0 configs/b.1/function0
echo "<udc device>" > UDC #fail to connect on Windows
This patch sets the use_os_string flag to false at bind if
the functions not support OS Descriptors.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Fixes: 87213d388e ("usb: gadget: configfs: OS String support")
Link: https://lore.kernel.org/r/1755833769-25434-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b570b346dd ]
In the twl6030_usb_probe(), the variable ret is declared as
a u32 type. However, since ret may receive -ENODEV when accepting
the return value of omap_usb2_set_comparator().Therefore, its type
should be changed to int.
Fixes: 0e98de67ba ("usb: otg: make twl6030_usb as a comparator driver to omap_usb2")
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250822092224.30645-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 186e8f2bdb ]
The kthread_run() function returns error pointers so the
max3421_hcd->spi_thread pointer can be either error pointers or NULL.
Check for both before dereferencing it.
Fixes: 05dfa5c9bc ("usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJTMVAPtRe5H6jug@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c428fce0 ]
Use "0x%x" format for quirks debug print to clarify it's a hexadecimal
value. Improves readability and consistency with other hex outputs.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20250603071045.3243699-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d63c83d8e ]
Yunseong Kim and the syzbot fuzzer both reported a problem in
RT-enabled kernels caused by the way dummy-hcd mixes interrupt
management and spin-locking. The pattern was:
local_irq_save(flags);
spin_lock(&dum->lock);
...
spin_unlock(&dum->lock);
... // calls usb_gadget_giveback_request()
local_irq_restore(flags);
The code was written this way because usb_gadget_giveback_request()
needs to be called with interrupts disabled and the private lock not
held.
While this pattern works fine in non-RT kernels, it's not good when RT
is enabled. RT kernels handle spinlocks much like mutexes; in particular,
spin_lock() may sleep. But sleeping is not allowed while local
interrupts are disabled.
To fix the problem, rewrite the code to conform to the pattern used
elsewhere in dummy-hcd and other UDC drivers:
spin_lock_irqsave(&dum->lock, flags);
...
spin_unlock(&dum->lock);
usb_gadget_giveback_request(...);
spin_lock(&dum->lock);
...
spin_unlock_irqrestore(&dum->lock, flags);
This approach satisfies the RT requirements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Fixes: b4dbda1a22 ("USB: dummy-hcd: disable interrupts during req->complete")
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: <https://lore.kernel.org/linux-usb/5b337389-73b9-4ee4-a83e-7e82bf5af87a@kzalloc.com/>
Reported-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
Closes: <https://lore.kernel.org/linux-usb/68ac2411.050a0220.37038e.0087.GAE@google.com/>
Tested-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
CC: stable@vger.kernel.org
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/bb192ae2-4eee-48ee-981f-3efdbbd0d8f0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7975f080d3 ]
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable [1].
Link: https://lore.kernel.org/all/YhdfEIwI4EdtHdym@kroah.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220308171818.384491-26-jakobkoschel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8d63c83d8e ("USB: gadget: dummy-hcd: Fix locking bug in RT-enabled kernels")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5c98e8b13 ]
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 220a0ffde0 ]
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2eb0337615 ]
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953e ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45eae113dc upstream.
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58577118cc upstream.
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98da66a70a upstream.
Since 'bcs->Residue' has the data type '__le32', convert it to the
correct byte order of the CPU using this driver when assigning it to
the local variable 'residue'.
Cc: stable <stable@kernel.org>
Fixes: 50a6cb932d ("USB: usb_storage: add ums-realtek driver")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20250813145247.184717-3-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9420f4757 upstream.
Increase the External ROM access timeouts to prevent failures during
programming of External SPI EEPROM chips. The current timeouts are
too short for some SPI EEPROMs used with uPD720201 controllers.
The current timeout for Chip Erase in renesas_rom_erase() is 100 ms ,
the current timeout for Sector Erase issued by the controller before
Page Program in renesas_fw_download_image() is also 100 ms. Neither
timeout is sufficient for e.g. the Macronix MX25L5121E or MX25V5126F.
MX25L5121E reference manual [1] page 35 section "ERASE AND PROGRAMMING
PERFORMANCE" and page 23 section "Table 8. AC CHARACTERISTICS (Temperature
= 0°C to 70°C for Commercial grade, VCC = 2.7V ~ 3.6V)" row "tCE" indicate
that the maximum time required for Chip Erase opcode to complete is 2 s,
and for Sector Erase it is 300 ms .
MX25V5126F reference manual [2] page 47 section "13. ERASE AND PROGRAMMING
PERFORMANCE (2.3V - 3.6V)" and page 42 section "Table 8. AC CHARACTERISTICS
(Temperature = -40°C to 85°C for Industrial grade, VCC = 2.3V - 3.6V)" row
"tCE" indicate that the maximum time required for Chip Erase opcode to
complete is 3.2 s, and for Sector Erase it is 400 ms .
Update the timeouts such, that Chip Erase timeout is set to 5 seconds,
and Sector Erase timeout is set to 500 ms. Such lengthy timeouts ought
to be sufficient for majority of SPI EEPROM chips.
[1] https://www.macronix.com/Lists/Datasheet/Attachments/8634/MX25L5121E,%203V,%20512Kb,%20v1.3.pdf
[2] https://www.macronix.com/Lists/Datasheet/Attachments/8750/MX25V5126F,%202.5V,%20512Kb,%20v1.1.pdf
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20250802225526.25431-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fe06185e1 upstream.
The USB core will unmap urb->transfer_dma after SETUP stage completes.
Then the USB controller will access unmapped memory when it received
device descriptor. If iommu is equipped, the entire test can't be
completed due to the memory accessing is blocked.
Fix it by calling map_urb_for_dma() again for IN stage. To reduce
redundant map for urb->transfer_buffer, this will also set
URB_NO_TRANSFER_DMA_MAP flag before first map_urb_for_dma() to skip
dma map for urb->transfer_buffer and clear URB_NO_TRANSFER_DMA_MAP
flag before second map_urb_for_dma().
Fixes: 216e0e563d ("usb: core: hcd: use map_urb_for_dma for single step set feature urb")
Cc: stable <stable@kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250806083955.3325299-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e664036cf3 upstream.
Another SanDisk 3.2Gen1 Flash Drive also need DELAY_INIT quick,
or it will randomly work incorrectly on Huawei hisi platforms
when doing reboot test.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250801082728.469406-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 086a0e516f ]
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1473e9e767 ]
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Removed populate_irqs-related goto changes ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb020bf522 ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230405141009.3400693-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1473e9e767 ("usb: musb: omap2430: fix device leak at unbind")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e61f6ab08 ]
This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.
I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:
1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
(tcpm_set_pd_rx is enabled again, even though it is still on)
At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.
I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.
Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)
As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:
On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.
Fixes: c034a43e72 ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ replaced str_on_off(on) with ternary operator ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2521106fc7 ]
Hub driver warm-resets ports in SS.Inactive or Compliance mode to
recover a possible connected device. The port reset code correctly
detects if a connection is lost during reset, but hub driver
port_event() fails to take this into account in some cases.
port_event() ends up using stale values and assumes there is a
connected device, and will try all means to recover it, including
power-cycling the port.
Details:
This case was triggered when xHC host was suspended with DbC (Debug
Capability) enabled and connected. DbC turns one xHC port into a simple
usb debug device, allowing debugging a system with an A-to-A USB debug
cable.
xhci DbC code disables DbC when xHC is system suspended to D3, and
enables it back during resume.
We essentially end up with two hosts connected to each other during
suspend, and, for a short while during resume, until DbC is enabled back.
The suspended xHC host notices some activity on the roothub port, but
can't train the link due to being suspended, so xHC hardware sets a CAS
(Cold Attach Status) flag for this port to inform xhci host driver that
the port needs to be warm reset once xHC resumes.
CAS is xHCI specific, and not part of USB specification, so xhci driver
tells usb core that the port has a connection and link is in compliance
mode. Recovery from complinace mode is similar to CAS recovery.
xhci CAS driver support that fakes a compliance mode connection was added
in commit 8bea2bd37d ("usb: Add support for root hub port status CAS")
Once xHCI resumes and DbC is enabled back, all activity on the xHC
roothub host side port disappears. The hub driver will anyway think
port has a connection and link is in compliance mode, and hub driver
will try to recover it.
The port power-cycle during recovery seems to cause issues to the active
DbC connection.
Fix this by clearing connect_change flag if hub_port_reset() returns
-ENOTCONN, thus avoiding the whole unnecessary port recovery and
initialization attempt.
Cc: stable@vger.kernel.org
Fixes: 8bea2bd37d ("usb: Add support for root hub port status CAS")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250623133947.3144608-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f59f93cd1d ]
During disconnect USB-3 ports often go via SS.Inactive link error state
before the missing terminations are noticed, and link finally goes to
RxDetect state
Avoid immediately warm-resetting ports in SS.Inactive state.
Let ports settle for a while and re-read the link status a few times 20ms
apart to see if the ports transitions out of SS.Inactive.
According to USB 3.x spec 7.5.2, a port in SS.Inactive should
automatically check for missing far-end receiver termination every
12 ms (SSInactiveQuietTimeout)
The futile multiple warm reset retries of a disconnected device takes
a lot of time, also the resetting of a removed devices has caused cases
where the reset bit got stuck for a long time on xHCI roothub.
This lead to issues in detecting new devices connected to the same port
shortly after.
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210111653.1378381-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2521106fc7 ("usb: hub: Don't try to recover devices lost during warm reset.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
