The patch cleans up the HT40 extension channels setup for EEPROM
band 6 and 7 to make it more readable.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver's first notification of a new station from mac80211 can be through rate
selection API. This patch fixes a bug where, in this code path, the HT
capabilities of the new station were ignored.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_chan_width entry is never used, supported_chan_width is used instead.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With EDCA and HCCA we have 16 potential tid values. This is accommodated by
mac80211, but iwlwifi only supports EDCA. With this implementation it is
thus possible for mac80211 to request a tid that will cause iwlwifi to read
outside array bounds. A similar problem exists if traffic is received in an
unsupported category.
We add error checking to catch these situations.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_wext_siwfreq() should be exported with EXPORT_SYMBOL_GPL.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW TX power control init still needs work.
The SW init is complete according to the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The V4 dummy transmission has two extra bools in its prototype,
so update all callers with the 2 bools.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current PCM core has the following problems regarding PCM draining
in non-blocking mode:
- the current f_flags isn't checked in snd_pcm_drain(), thus changing
the mode dynamically via snd_pcm_nonblock() after open doesn't work.
- calling drain in non-blocking mode just return -EAGAIN error, but
doesn't provide any way to sync with draining.
This patch fixes these issues.
- check file->f_flags in snd_pcm_drain() properly
- when O_NONBLOCK is set, PCM core sets the stream(s) to DRAIN state
but quits ioctl immediately without waiting the whole drain; the
caller can sync the drain manually via poll()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are seeing a number of crashes in SMM, when VT-d is enabled while
'Legacy USB support' is enabled in various BIOSes.
The BIOS is supposed to indicate which addresses it uses for DMA in a
special ACPI table ("RMRR"), so that we can punch a hole for it when we
set up the IOMMU.
The problem is, as usual, that BIOS engineers are totally incompetent.
They write code which will crash if the DMA goes AWOL, and then they
either neglect to provide an RMRR table at all, or they put the wrong
addresses in it. And of course they don't do _any_ QA, since that would
take too much time away from their crack-smoking habit.
The real fix, of course, is for consumers to refuse to buy motherboards
which only have closed-source firmware available. If we had _open_
firmware, bugs like this would be easy to fix.
Since that's something I can only dream about, this patch implements an
alternative -- ensuring that the USB controllers are handed off from the
BIOS and quiesced _before_ the IOMMU is initialised. That would have
been a much better design than this RMRR nonsense in the first place, of
course. The bootloader has no business doing DMA after the OS has booted
anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace for loop with the macro for_each_class to cleanup.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
LKML-Reference: <4A8A277D.4090304@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
hiddev userspace driver uses a rignbuffer to store the parsed usages
that should be returned through read(). This buffer is 64 bytes long,
which is sufficient for queueing single USB 1.0 low-speed report, which
is of maximum size 48 bytes.
There are however USB HID devices which are full-speed USB devices, and
therefore they are free to produce reports 64 bytes long. This is correctly
handled by HID core, but read() on hiddev node gets stuck forever, because
the ring buffer loops infinitely (as it is exactly 64 bytes long as well),
never advancing the buffer pointer.
Plus, the core driver is ready to handle highspeed devices, so we should be
able to handle reports from such devices in the hiddev driver as well, which
means we need larger ringbuffer.
Reported-by: Michael Zeisel <michael.zeisel@philips.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the Xilinx Ethernet Lite device. The
soft logic core from Xilinx is typically used on Virtex and Spartan
designs attached to either a PowerPC or a Microblaze processor.
Signed-off-by: Sadanand M <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ibm_newemac netdev instance is shutdown with "ifconfig down",
the netdev interface does not go properly down. netif_carrier_ok()
keeps returning TRUE even after "ifconfig down".
The problem can be seen when ibm_newemac instances are slaves of
a bonding interface. The bonding interface code uses netif_carrier_ok()
to determine the link status of its slaves. When ibm_newemac slave is
shutdown with "ifconfig down", the bonding interface won't detect any
link status change because netif_carrier_ok() keeps returning TRUE.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ttm:
Fix error paths when kobject_add returns an error.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm:
Remove a stray debug printout.
Remove a re-init of the lru spinlock at device init.
radeon:
Fix the size of the bo_global allocation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When get_mmu_context() runs out of new ASIDs it flushes the TLB and
wraps around. Despite the fact the ASIDs are tracked per-CPU, a global
TLB flush was being used. Switch this over to a local one, as matches
the intent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The alignment calculation of xcbc_tfm_ctx uses alg->cra_alignmask
and not alg->cra_alignmask + 1 as it should. This led to frequent
crashes during the selftest of xcbc(aes-asm) on x86_64
machines. This patch fixes this. Also we use the alignmask
of xcbc and not the alignmask of the underlying algorithm
for the alignmnent calculation in xcbc_create now.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
What about something like this? It defaults the CPRNG to m and makes FIPS
dependent on the CPRNG. That way you get a module build by default, but you can
change it to y manually during config and still satisfy the dependency, and if
you select N it disables FIPS as well. I rather like that better than making
FIPS a tristate. I just tested it out here and it seems to work well. Let me
know what you think
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:
- In the DSP restore case a0 needs to be popped off before a0g,
or the value of a0g is clobbered by the MSB of a0 in the case
of sign extension.
- Beyond that, the save and restore orders were out of sync,
so this fixes that up as well. At the same time, we switch over
to using movs.l for both the save and restore of the general DSP
registers as opposed to using sts.l (which was initially put in
place to work around a bug in ancient binutils versions which
the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- removed spinlock protection, it's handled by the rtc class
- use platform_driver_probe
- return appropriate code for rtc_read_time
- style issues
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves the disable_controller() function in the
r8a66597-udc driver to disable all interrupts and also clear
status flags. With this patch in place the driver survives
kexec.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the r8a66597-udc buffer management code.
Use fixed buffers for bulk and isochronous pipes, also make
sure to handle the isochronous-as-bulk case. With fixed buffers
there is no need to keep track of used buffers with bi_bufnum.
Also, this fixes a potential buffer offset problem where the
base offset incorrectly varies with the number of pipes used.
The m66592 driver recently got fixed in a similar way.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the clock framework to the r8a66597 gadget driver.
This is needed to control the clock driving the USB block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While in-tree support for the R8A66597 host side has been supported for
some time, the peripheral side has so far been unsupported. This adds a
new USB gadget driver which bridges the gap and finally wires up the
peripheral side as well.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently _edata does not include several data sections, this causes
the kernel's report of memory usage at boot to not match reality, and
also prevents kmemleak from working - because it scan between _sdata
and _edata for pointers to allocated memory.
This mirrors a similar change made recently to the x86 linker script.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make it possible to enable GCOV code coverage measurement on powerpc.
Lightly tested on 64-bit, seems to work as expected.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Check whether index is within bounds prior to calculating a
possibly-invalid address.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Bernd Petrovitsch <bernd@firmix.at>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hardirq.h on powerpc defines a __last_jiffy_stamp field, but it's not
actually used anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Map the GART table uncached, so we don't always need to flush the CPU caches
explicitly after updates.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using the radeon KMS test functionality, I verified that the AGP bridge of the
Intrepid2 chipset in my PowerBook supports aperture sizes up to 256M. So allow
aperture sizes up to 256M on pre-U3 bridges as well, and bump the default size
to 256M. It's possible that older revisions only support smaller sizes, but
it'll be easy to verify that with the raden KMS test functionality. Also,
there's only a problem on an actual attempt to access the aperture beyond the
maximum size supported by the hardware, and non-KMS X still defaults to using
only 32M.
Also use ARRAY_SIZE for the aperture size arrays.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Check whether index is within bounds before grabbing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>