set_infra_mode() tried to restore wpa keys using add_wep_key(). This never
worked so prevent driver from trying.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split add_wpa_key() from rndis_iw_set_encode_ext so that conversion to cfg80211
would be easier later on.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver uses some unnamed bits to control encryption setup. Move these to
enumerations with proper names explaining their meaning.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature measurement by uCode for 5150 and 5000 are different
CSR_HW_REV_TYPE_5150: temperature sensor output voltage
CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.
To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.
Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.
This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.
SD8688 firmware introduces a new register for firmware status
which will never be overwritten.
Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.
In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.
When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).
This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688: IF_SDIO_SCRATCH (0x34/0x35)
Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN 0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in. This
can lead, for example, to the card failing to re-associate. This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").
This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I tried to run with 300 active counters and the tools bailed out
because our limit was at 64. So increase the counter limit to 1024
and the CPU limit to 4096.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
MIPS: IP32: Fix build error due to uninitialized variable.
MIPS: Fix sparse warning in incompatiable argument type of clear_user.
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The WM9081 is designed to provide high power output at low distortion
levels in space-constrained portable applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give unique stream names for the two playback streams so
DAPM can figure out which codec_dai is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They are unneeded and as the issue fixed in lmo commit
63f7ec59053e3f850ab67a9938e631bcba64c6ce shows even harmful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip32/ip32-reset.o
cc1: warnings being treated as errors
arch/mips/sgi-ip32/ip32-reset.c: In function 'debounce':
arch/mips/sgi-ip32/ip32-reset.c:97: error: 'reg_a' is used uninitialized in this function
The issues is old but due to the volatile keyword gcc older than 4.4 did
not warn about this obvious bug.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The type of the second argument of access_ok should be (void __user *).
The unnecessary conversion of the clear_user address argument was causing
sparse to emit warnings on the __chk_user_ptr check.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a new memory leak problem in garbage collection. The
problem was brought by the bugfix patch ("nilfs2: fix lock order
reversal in nilfs_clean_segments ioctl").
Thanks to Kentaro Suzuki for finding this problem.
Reported-by: Kentaro Suzuki <k_suzuki@ms.sylc.co.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
When monitoring a process and its descendants with a set of inherited
counters, we can often get the situation in a context switch where
both the old (outgoing) and new (incoming) process have the same set
of counters, and their values are ultimately going to be added together.
In that situation it doesn't matter which set of counters are used to
count the activity for the new process, so there is really no need to
go through the process of reading the hardware counters and updating
the old task's counters and then setting up the PMU for the new task.
This optimizes the context switch in this situation. Instead of
scheduling out the perf_counter_context for the old task and
scheduling in the new context, we simply transfer the old context
to the new task and keep using it without interruption. The new
context gets transferred to the old task. This means that both
tasks still have a valid perf_counter_context, so no special case
is introduced when the old task gets scheduled in again, either on
this CPU or another CPU.
The equivalence of contexts is detected by keeping a pointer in
each cloned context pointing to the context it was cloned from.
To cope with the situation where a context is changed by adding
or removing counters after it has been cloned, we also keep a
generation number on each context which is incremented every time
a context is changed. When a context is cloned we take a copy
of the parent's generation number, and two cloned contexts are
equivalent only if they have the same parent and the same
generation number. In order that the parent context pointer
remains valid (and is not reused), we increment the parent
context's reference count for each context cloned from it.
Since we don't have individual fds for the counters in a cloned
context, the only thing that can make two clones of a given parent
different after they have been cloned is enabling or disabling all
counters with prctl. To account for this, we keep a count of the
number of enabled counters in each context. Two contexts must have
the same number of enabled counters to be considered equivalent.
Here are some measurements of the context switch time as measured with
the lat_ctx benchmark from lmbench, comparing the times obtained with
and without this patch series:
-----Unmodified----- With this patch series
Counters: none 2 HW 4H+4S none 2 HW 4H+4S
2 processes:
Average 3.44 6.45 11.24 3.12 3.39 3.60
St dev 0.04 0.04 0.13 0.05 0.17 0.19
8 processes:
Average 6.45 8.79 14.00 5.57 6.23 7.57
St dev 1.27 1.04 0.88 1.42 1.46 1.42
32 processes:
Average 5.56 8.43 13.78 5.28 5.55 7.15
St dev 0.41 0.47 0.53 0.54 0.57 0.81
The numbers are the mean and standard deviation of 20 runs of
lat_ctx. The "none" columns are lat_ctx run directly without any
counters. The "2 HW" columns are with lat_ctx run under perfstat,
counting cycles and instructions. The "4H+4S" columns are lat_ctx run
under perfstat with 4 hardware counters and 4 software counters
(cycles, instructions, cache references, cache misses, task
clock, context switch, cpu migrations, and page faults).
[ Impact: performance optimization of counter context-switches ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18966.10666.517218.332164@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This replaces the struct perf_counter_context in the task_struct with
a pointer to a dynamically allocated perf_counter_context struct. The
main reason for doing is this is to allow us to transfer a
perf_counter_context from one task to another when we do lazy PMU
switching in a later patch.
This has a few side-benefits: the task_struct becomes a little smaller,
we save some memory because only tasks that have perf_counters attached
get a perf_counter_context allocated for them, and we can remove the
inclusion of <linux/perf_counter.h> in sched.h, meaning that we don't
end up recompiling nearly everything whenever perf_counter.h changes.
The perf_counter_context structures are reference-counted and freed
when the last reference is dropped. A context can have references
from its task and the counters on its task. Counters can outlive the
task so it is possible that a context will be freed well after its
task has exited.
Contexts are allocated on fork if the parent had a context, or
otherwise the first time that a per-task counter is created on a task.
In the latter case, we set the context pointer in the task struct
locklessly using an atomic compare-and-exchange operation in case we
raced with some other task in creating a context for the subject task.
This also removes the task pointer from the perf_counter struct. The
task pointer was not used anywhere and would make it harder to move a
context from one task to another. Anything that needed to know which
task a counter was attached to was already using counter->ctx->task.
The __perf_counter_init_context function moves up in perf_counter.c
so that it can be called from find_get_context, and now initializes
the refcount, but is otherwise unchanged.
We were potentially calling list_del_counter twice: once from
__perf_counter_exit_task when the task exits and once from
__perf_counter_remove_from_context when the counter's fd gets closed.
This adds a check in list_del_counter so it doesn't do anything if
the counter has already been removed from the lists.
Since perf_counter_task_sched_in doesn't do anything if the task doesn't
have a context, and leaves cpuctx->task_ctx = NULL, this adds code to
__perf_install_in_context to set cpuctx->task_ctx if necessary, i.e. in
the case where the current task adds the first counter to itself and
thus creates a context for itself.
This also adds similar code to __perf_counter_enable to handle a
similar situation which can arise when the counters have been disabled
using prctl; that also leaves cpuctx->task_ctx = NULL.
[ Impact: refactor counter context management to prepare for new feature ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18966.10075.781053.231153@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch modifies parameter of clksrc_read() from 'void' to
'struct clocksource *cs', which fixes compile warning for
incompatible parameter type.
Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>