In some cases, we need access to information before it becomes available
to the 'event' handler. In particular, for some devices we cannot properly
process the finger data without first knowing the "contact count" at the
very end of the report (e.g. the Cintiq 24HDT touch screen, when forced
through the GENERIC codepath).
Since the HID subsystem doesn't provide a way to take action before 'event'
is called, we take a cue from hid-multitouch.c and add a pre-process step
within the 'report' handler that performs the same function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch extends the reporting of the RSS key and hash table by
adding support for X550 VFs. The difference is that X550 VFs have
their own registers for RSS key and indirection table, so there is
no need to query the PF.
The RSS key and indirection table are stored in the adapter structure
during the configuration of VFRSSRK and VFRETA which in turn can be
used in ethtool for reporting.
The logic for writing VFRETA is also changed to make sure that the
indirection table is reported correctly.
In addition this patch adds defines for the VFRETA entries and number
of VFRSSRK registers as well as some whitespace cleanups.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PRCM IRQ entry. This is needed for I/O wakeup support.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: added I/O wakeup note in commit description]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRM IRQ register offsets. This is needed to support PRM I/O
wakeup on AM43xx.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: improved patch description, moved the PRM_IO_PMCTRL macro
out of the CM section]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
PRM_IO_PMCTRL_OFFSET need not be same for all SOCs hence
remove hardcoding and use the value provided by the omap_prcm_irq_setup
structure. This is done to support IO wakeup on am437x series.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
ST's Low Power Controller can now operate in three supported modes;
Watchdog, Real Time Clock and most recently as a Clocksource. This new
define will allow the LPC IP to be configured for Clocksource from DT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the common 'platform' registration module, and move the crypto
compression driver registration into each of the pSeries and PowerNV
platform NX 842 drivers. Change the nx-842.c code into simple common
functions that each platform driver uses to perform constraints-based
buffer changes, i.e. realigning and/or resizing buffers to match the
driver's hardware requirements.
The common 'platform' module was my mistake to create - since each
platform driver will only load/operate when running on its own
platform (i.e. a pSeries platform or a PowerNV platform), they can
directly register with the crypto subsystem, using the same alg and
driver name. This removes unneeded complexity.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The last commit merged nx-842.c's code into nx-842-crypto.c. It
did not rename nx-842-crypto.c to nx-842.c, in order to let the
patch more clearly show what was merged. This just renames
nx-842-crypto.c to nx-842.c, with no changes to its code.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge the nx-842.c code into nx-842-crypto.c.
This allows later patches to remove the 'platform' driver, and instead
allow each platform driver to directly register with the crypto
compression api.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the duplicated finishing code (set destination buffer length and
set return code to 0) in the case of decompressing a buffer with no header
with a goto to the success case of decompressing a buffer with a header.
This is a trivial change that allows both success cases to use common code,
and includes the pr_debug() msg in both cases as well.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't register the pSeries driver when parsing the device tree returns
ENODEV.
The nx842_probe() function in the pSeries driver returns error instead
of registering as a crypto compression driver, when it receives an
error return value from the nx842_OF_upd() function that probes the
device tree nodes, except when ENODEV is returned. However ENODEV
should not be a special case and the driver should not register when
there is no hw device, or the hw device is disabled.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the kzalloc() calls in nx842_probe() and nx842_OF_upd() to the top
of the functions, before taking the devdata spinlock.
Since kzalloc() without GFP_ATOMIC can sleep, it can't be called while
holding a spinlock. Move the calls to before taking the lock.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the 'status' field from the pSeries NX driver data.
The 'status' field isn't used by the driver at all; it simply checks the
devicetree status node at initialization, and returns success if 'okay'
and failure otherwise.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the __init and __exit modifiers from the VIO driver probe and
remove functions.
The driver functions should not be marked __init/__exit because they
can/will be called during runtime, not only at module init and exit.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When multiple devices are present in the system the driver attempts
to register the same algorithm many times.
Changes in v2:
- use proper synchronization mechanizm between register and unregister
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes a bogus BUG_ON in the ablkcipher path that
triggers when the destination buffer is different from the source
buffer and is scattered.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The synchronization method used atomic was bogus.
Use a proper synchronization with mutex.
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After commit 0fd972a7d9 ("module: relocate module_init from init.h to module.h")
ans-lcd module fails to build with:
drivers/macintosh/ans-lcd.c:201:1: warning: data definition has no type or storage class [enabled by default]
module_init(anslcd_init);
^
drivers/macintosh/ans-lcd.c:201:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
drivers/macintosh/ans-lcd.c:201:1: warning: parameter names (without types) in function declaration [enabled by default]
drivers/macintosh/ans-lcd.c:202:1: warning: data definition has no type or storage class [enabled by default]
module_exit(anslcd_exit);
^
drivers/macintosh/ans-lcd.c:202:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
drivers/macintosh/ans-lcd.c:202:1: warning: parameter names (without types) in function declaration [enabled by default]
drivers/macintosh/ans-lcd.c:155:1: warning: 'anslcd_init' defined but not used [-Wunused-function]
anslcd_init(void)
^
drivers/macintosh/ans-lcd.c:195:1: warning: 'anslcd_exit' defined but not used [-Wunused-function]
anslcd_exit(void)
^
This commit fixes it by replacing linux/init.h by linux/module.h.
Fixes: 0fd972a7d9 ("module: relocate module_init from init.h to module.h")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The existing code stores the amount of memory allocated for a TCE table.
At the moment it uses @offset which is a virtual offset in the TCE table
which is only correct for a one level tables and it does not include
memory allocated for intermediate levels. When multilevel TCE table is
requested, WARN_ON in tce_iommu_create_table() prints a warning.
This adds an additional counter to pnv_pci_ioda2_table_do_alloc_pages()
to count actually allocated memory.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hardware RNG on POWER8 and POWER7+ can be relatively slow, since
it can only supply one 64-bit value per microsecond. Currently we
read it in arch_get_random_long(), but that slows down reading from
/dev/urandom since the code in random.c calls arch_get_random_long()
for every longword read from /dev/urandom.
Since the hardware RNG supplies high-quality entropy on every read, it
matches the semantics of arch_get_random_seed_long() better than those
of arch_get_random_long(). Therefore this commit makes the code use
the POWER8/7+ hardware RNG only for arch_get_random_seed_{long,int}
and not for arch_get_random_{long,int}.
This won't affect any other PowerPC-based platforms because none of
them currently support a hardware RNG. To make it clear that the
ppc_md function pointer is used for arch_get_random_seed_*, we rename
it from get_random_long to get_random_seed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6
Call Trace:
[c00000007ffe7b90] [c000000000807670] dump_stack+0xa0/0xdc (unreliable)
[c00000007ffe7bc0] [c0000000000e1f14] ___might_sleep+0x134/0x180
[c00000007ffe7c20] [c00000000002aec0] rtas_busy_delay+0x30/0xd0
[c00000007ffe7c50] [c00000000002bde4] rtas_get_sensor+0x74/0xe0
[c00000007ffe7ce0] [c000000000083264] ras_epow_interrupt+0x44/0x450
[c00000007ffe7d90] [c000000000120260] handle_irq_event_percpu+0xa0/0x300
[c00000007ffe7e70] [c000000000120524] handle_irq_event+0x64/0xc0
[c00000007ffe7eb0] [c000000000124dbc] handle_fasteoi_irq+0xec/0x260
[c00000007ffe7ef0] [c00000000011f4f0] generic_handle_irq+0x50/0x80
[c00000007ffe7f20] [c000000000010f3c] __do_irq+0x8c/0x200
[c00000007ffe7f90] [c0000000000236cc] call_do_irq+0x14/0x24
[c00000007e6f39e0] [c000000000011144] do_IRQ+0x94/0x110
[c00000007e6f3a30] [c000000000002594] hardware_interrupt_common+0x114/0x180
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd ("powerpc/pseries: Use rtas_get_sensor in RAS code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the pin controller probes before the GPIO driver it needs to
populate the GPIO driver state containers ahead of the actual
driver probe as the addresses are used by both halves of the
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of indexing around the GPIO ranges to find a chip, look directly
in the local array of state containers for nmk_gpio_chip:s.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Break out the function that allocates the nomadik GPIO chip state
container to its own function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can disable CD unconditionally when there is no assigned device.
KVM now forces guest PAT to all-writeback in that case, so it makes
sense to also force CR0.CD=0.
When there are assigned devices, emulate cache-disabled operation
through the page tables. This behavior is consistent with VMX
microcode, where CD/NW are not touched by vmentry/vmexit. However,
keep this dependent on the quirk because OVMF enables the caches
too late.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow a nested hypervisor to single step its guests.
Signed-off-by: Mihai Donțu <mihai.dontu@gmail.com>
[Fix overlong line. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sending of notification is done by exiting vcpu to user space
if KVM_REQ_HV_CRASH is enabled for vcpu. At exit to user space
the kvm_run structure contains system_event with type
KVM_SYSTEM_EVENT_CRASH to notify about guest crash occurred.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vcpu_debug is useful macro like kvm_debug but additionally
includes vcpu context inside output.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduce Hyper-V related source code file - hyperv.c and
per vm and per vcpu hyperv context structures.
All Hyper-V MSR's and hypercall code moved into hyperv.c.
All Hyper-V kvm/vcpu fields moved into appropriate hyperv context
structures. Copyrights and authors information copied from x86.c
to hyperv.c.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
rtas.h already has some nice #defines for RTAS return status
codes - let's use them instead of hard-coded "magic" values!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
According to Intel SDM several checks must be applied for memory operands
of VMX instructions.
Long mode: #GP(0) or #SS(0) depending on the segment must be thrown
if the memory address is in a non-canonical form.
Protected mode, checks in chronological order:
- The segment type must be checked with access type (read or write) taken
into account.
For write access: #GP(0) must be generated if the destination operand
is located in a read-only data segment or any code segment.
For read access: #GP(0) must be generated if if the source operand is
located in an execute-only code segment.
- Usability of the segment must be checked. #GP(0) or #SS(0) depending on the
segment must be thrown if the segment is unusable.
- Limit check. #GP(0) or #SS(0) depending on the segment must be
thrown if the memory operand effective address is outside the segment
limit.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make them clearly architecture-dependent; the capability is valid for
all architectures, but the argument is not.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF depends on WB to boot fast, because it only clears caches after
it has set up MTRRs---which is too late.
Let's do writeback if CR0.CD is set to make it happy, similar to what
SVM is already doing.
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic of the disabled_quirks field usually results in a double
negation. Wrap it in a simple function that checks the bit and
negates it.
Based on a patch from Xiao Guangrong.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mtrr_get_guest_memory_type never returns -1 which is implied
in the current code since if @type = -1 (means no MTRR contains the
range), iter.partial_map must be true
Simplify the code to indicate this fact
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently code uses default memory type if MTRR is fully disabled,
fix it by using UC instead.
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces use of linux,stdout-path by stdout-path as per
"chosen" DT bindings documentation.
Doing that, the "console" argument is no more needed in kernel command
line.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
chrdev_open() increases reference counter on cdev->owner. Instead of
assigning the owner to mei subsystem, the owner has to be set to the
underlaying HW module (mei_me or mei_txe), so once the device is opened
the HW module cannot be unloaded.
Cc: <stable@vger.kernel.org> #3.17+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename init_hal_dm to rtl92e_dm_init.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename init_firmware to rtl92e_init_fw.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename rtllib_ips_leave_wq to rtl92e_rtllib_ips_leave_wq.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename rtllib_ips_leave to rtl92e_rtllib_ips_leave.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_wakeup_wq to rtl92e_hw_wakeup_wq.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_wakeup to rtl92e_hw_wakeup.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_to_sleep to rtl92e_enter_sleep.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
