With reworked device tree files for Compulab CM-A510 SoM and SBC-A510
base board, now add the correspoding board file to Makefile again.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Existing dts file for Compulab CM-A510 was very limited due to missing
hardware. Now that we actually found somebody with that board, properly
rework it to provide a CoM/SoM include and a board file for Compulab's
SBC-A510.
Both the CM-A510 SoM and the SBC-A510 can be configured with different
options, so we only enable a minimum set of options. The actual board
configuration will have to be set by either the bootloader or user.
Although functionally not required, repeat even disabled nodes again
to increse their visibility in the dtsi/dts files.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Gabriel Dobato <dobatog@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Prior reworking Dove based Compulab CM-A510 device tree, remove it
from the compiled device tree files.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This adds a i2c-mux-pinctrl node to dove.dtsi for the internal i2c
mux found on Dove SoCs. Up to now, we had no board using any of the
two additional i2c busses, so make sure the change does not break
any existing boards.
Therefore, we rename the i2c-controller node label to "i2c" and
enable it by default. Also, the dedicated sub-bus (now "i2c0") is
enabled by default. The two optional sub-busses require additional
external pin-muxing, so disable them by default.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The chandef of the current channel context might be wider (though
compatible). The TDLS link cares only about the channel of the BSS.
In addition make sure to specify the VHT operation IE when VHT is supported
on a non-2.4GHz band, as required by IEEE802.11ac-2013. This is not the
same as HT-operation, to be specified only if the BSS doesn't support HT.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove checking tailroom when adding IV as it uses only
headroom, and move the check to the ICV generation that
actually needs the tailroom.
In other case I hit such warning and datapath don't work,
when testing:
- IBSS + WEP
- ath9k with hw crypt enabled
- IPv6 data (ping6)
WARNING: CPU: 3 PID: 13301 at net/mac80211/wep.c:102 ieee80211_wep_add_iv+0x129/0x190 [mac80211]()
[...]
Call Trace:
[<ffffffff817bf491>] dump_stack+0x45/0x57
[<ffffffff8107746a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8107755a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc09ae109>] ieee80211_wep_add_iv+0x129/0x190 [mac80211]
[<ffffffffc09ae7ab>] ieee80211_crypto_wep_encrypt+0x6b/0xd0 [mac80211]
[<ffffffffc09d3fb1>] invoke_tx_handlers+0xc51/0xf30 [mac80211]
[...]
Cc: stable@vger.kernel.org
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enables the headset microphone on Dell Inspiron 5548,
or at least some variants of it.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1452175
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
same as legitimize_mnt(), except that it does *not* drop and regain
rcu_read_lock; return values are
0 => grabbed a reference, we are fine
1 => failed, just go away
-1 => failed, go away and mntput(bastard) when outside of rcu_read_lock
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We *can't* call that audit garbage in RCU mode - it's doing a weird
mix of allocations (GFP_NOFS, immediately followed by GFP_KERNEL)
and I'm not touching that... thing again.
So if this security sclero^Whardening feature gets triggered when
we are in RCU mode, tough - we'll fail with -ECHILD and have
everything restarted in non-RCU mode. Only to hit the same test
and fail, this time with EACCES and with (oh, rapture) an audit spew
produced.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
very simple - just make path_put() conditional on !RCU.
Note that right now it doesn't get called in RCU mode -
we leave it before getting anything into stack.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
inode_follow_link now takes an inode and rcu flag as well as the
dentry.
inode is used in preference to d_backing_inode(dentry), particularly
in RCU-walk mode.
selinux_inode_follow_link() gets dentry_has_perm() and
inode_has_perm() open-coded into it so that it can call
avc_has_perm_flags() in way that is safe if LOOKUP_RCU is set.
Calling avc_has_perm_flags() with rcu_read_lock() held means
that when avc_has_perm_noaudit calls avc_compute_av(), the attempt
to rcu_read_unlock() before calling security_compute_av() will not
actually drop the RCU read-lock.
However as security_compute_av() is completely in a read_lock()ed
region, it should be safe with the RCU read-lock held.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This allows MAY_NOT_BLOCK to be passed, in RCU-walk mode, through
the new avc_has_perm_flags() to avc_audit() and thence the slow_avc_audit.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make use of d_backing_inode() in pathwalk to gain access to an
inode or dentry that's on a lower layer.
Signed-off-by: David Howells <dhowells@redhat.com>
Lift it from link_path_walk(), trailing_symlink(), lookup_last(),
mountpoint_last(), complete_walk() and do_last(). A _lot_ of
those suckers merge.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make trailing_symlink() return the pathname to traverse or ERR_PTR(-E...).
A subtle point is that for "magic" symlinks it returns "" now - that
leads to link_path_walk("", nd), which is immediately returning 0 and
we are back to the treatment of the last component, at whereever the
damn thing has left us.
Reduces the stack footprint - link_path_walk() called on more shallow
stack now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* lift link_path_walk() into callers; moving it down into path_init()
had been a mistake. Stack footprint, among other things...
* do _not_ call path_cleanup() after path_init() failure; on all failure
exits out of it we have nothing for path_cleanup() to do
* have path_init() return pathname or ERR_PTR(-E...)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Mostly a bunch of fixes, reworks and optimizations for s390.
There is one new feature (EDAT-2 inside the guest), which boils
down to 2GB pages.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=ovvI
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150508' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes and features for 4.2 (kvm/next)
Mostly a bunch of fixes, reworks and optimizations for s390.
There is one new feature (EDAT-2 inside the guest), which boils
down to 2GB pages.
we can do fdput() under rcu_read_lock() just fine; all we need to take
care of is fetching nd->inode value first.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When an IBSS station gets QoS enabled after having been added,
check fast-xmit to make sure the QoS header gets added to the
cache properly and frames can go out with QoS and higher rates.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch enables full AHCI feature support for APM X-Gene SoC SATA
host controller. The following errata's are removed:
1. 2a0bdff6b9 ("ahci-xgene: fix the dma state machine lockup for the
IDENTIFY DEVICE PIO mode command")
2. 09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command")
3. 1540035da7 ("ahci_xgene: Implement the xgene_ahci_poll_reg_val to
support PMP")
4. a3a84bc7c8 ("ahci_xgene: Implement the workaround to support PMP
enumeration and discovery")
5. 1102407bb7 ("ahci_xgene: Fix the DMA state machine lockup for the
ATA_CMD_PACKET PIO mode command")
6. 72f79f9e35 ("ahci_xgene: Removing NCQ support from the APM X-Gene
SoC AHCI SATA Host Controller driver")
In addition, enable PMP support for APM X-Gene SoC and enable FBS
support for second generation APM X-Gene SoC.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVT9fTAAoJEHm+PkMAQRiGrbYH/276n6aKSORO0B6DrEnebu8Y
oxfJeacg90/N5aLx/B5GEplO24uTENaAfB342WkexziXdY+7P02J0Y36eSh5WiL2
qcL+gkiZVaApZIjVeO/y2ByL7nLprPeIsxl5gGLhI+qYYMaQ8gtzxC7sDLnNqjPS
w8WYQB7LdWeGFqcuvySEX2C6Q62aHpZWoSsV3LYdrfoDJz2lv1DJrOpRhqXPagl7
oX1c1CWQ4yWdFf9xm8vaiZw7EskxEnObQm7n7vWlZ0xAhXZ/3a7bPdc+fj2V+nve
xjZV/EhEL0u3ME86bVtcqbO3lgMjivyWHjQglCwG6keS+iIHkL0xMlQabkrFJhw=
=LGDf
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc3' into patchwork
Linux 4.1-rc3
* tag 'v4.1-rc3': (381 commits)
Linux 4.1-rc3
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
m32r: make flush_cpumask non-volatile.
mnt: Fix fs_fully_visible to verify the root directory is visible
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
...
OpenPower BMC machines do not place any sysparams in the device tree, so
at every boot we get a warning:
[ 0.437176] SYSPARAM: Opal sysparam node not found
Remove the warning, and reorder the init so we don't peform allocations
when there is no sysparam node in the device tree.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Traffic on the cbe-oss-dev list is more or less non-existent, other than
CC's from linuxppc.
It's seems like we may as well just send everyone to linuxppc and
archive the list.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The only little endian configuration we support is ppc64le. As such if
we're building little endian we don't need a 32-bit VDSO, because there
is no 32-bit userspace.
This patch is a fairly ugly mess of #ifdefs, but is the minimal logic
required to disable the 32-bit VDSO. We can hopefully clean up the
result in future with some further refactoring.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In vdso_fixup_features() we have start64/start32 and size64/size32, but
they have the same types, ie. void * and unsigned long.
They're only used to save the return value from find_sectionXX() for the
subsequent call to do_feature_fixups(), so there's no overlap in their
usage either.
So we can just consolidate them into start/size and avoid the
duplication.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a bug in binutils 2.24 which causes miscompilation if we're
building little endian and using weak symbols (which the kernel does).
It is fixed in binutils commit 57fa7b8c7e59 "Correct elf_merge_st_other
arguments for weak symbols", which is in binutils 2.25 and has been
backported to the binutils 2.24 branch and has been picked up by most
distros it seems.
However if we're running stock 2.24 (no extra version) then the bug is
present, so check for that and bail.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables the uncore Memory Controller (IMC) PMU
support for Intel Broadwell-U (Model 61) mobile processors.
The IMC PMU enables measuring memory bandwidth.
To use with perf:
$ perf stat -a -I 1000 -e
uncore_imc/data_reads/,uncore_imc/data_writes/ sleep 10
Tested-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kan.liang@intel.com
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/20150423065642.GA4890@thinkpad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have several checks for bad gcc versions in our Makefile. These don't
apply if we're building with clang, so skip them in that case.
The obvious check would be for ${COMPILER} = "gcc", but because of the
way the logic in the top level Makefile conditionally sets COMPILER,
it's possible that we're building with gcc but COMPILER was not set.
So instead check for ${COMPILER} != "clang", which we know is currently
the only other possibility.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ACPI specification knows two types of GPIOs: GpioIo and GpioInt. The latter
is used to describe that a given device interrupt line is connected to a
specific GPIO pin. Typical ACPI _CRS entry for such device looks like
below:
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x004A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C6",
0x00, ResourceConsumer)
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\_SB.GPO0",
0x00, ResourceConsumer)
{
0x004B
}
GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x004C
}
})
Currently drivers need to request a GPIO corresponding to the right GpioInt
and then translate that to Linux IRQ number. This adds unnecessary lines of
boiler-plate code.
We can ease this a bit by introducing acpi_dev_gpio_irq_get() analogous to
of_irq_get(). This function translates given GpioInt resource under the
device in question to the suitable Linux IRQ number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we print "Starting Linux PPC64" at boot. But we don't mention
anywhere whether the kernel is big or little endian.
If we print the utsname->machine value instead we get either "ppc64" or
"ppc64le" which is much more informative, eg:
Starting Linux ppc64le #1 SMP Wed Apr 15 12:12:20 AEST 2015
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pasemi MSI code is currently always built when MPIC=y && PCI_MSI=y.
It should not have any effect on other platforms, because it immediately
checks the MPIC's compatible property for "pasemi,pwrficient-openpic".
However it's odd that it's still built even when PASEMI=n. It also
needn't be in sysdev, as it's only used by pasemi. So move it into
platforms/pasemi, whereby it will only be built for PASEMI=y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch doesn't change any logic.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1429776428-4475-1-git-send-email-decui@microsoft.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The STRICT_MM_TYPECHECKS code has bit-rotted over the years. To make it
possible to easily build test it, make it a CONFIG option.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All supported iMX GPIO controllers store configured GPIO output value
in GPIO_DR data register, which is represented by GPIO generic reg_set.
Provide a BGPIOF_READ_OUTPUT_REG_SET flag to bgpio_init() to allow
correct getting of previously set output value.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding a BGPIOF_READ_OUTPUT_REG_SET initialization flag to GPIO
generic MMIO driver makes possible to remove a private get() value
function from the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change introduces BGPIOF_READ_OUTPUT_REG_SET flag for gpio-generic
GPIO chip implementation, which allows to get correct configured value
from reg_set register, input value is still get from reg_dat.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock-frequency property became obsolete since the rework of the main
clock driver in 3.16 (see commit 27cb1c2083).
It now get and uses the clock-frequency from the main_xtal node.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
