Revert the problematic part of commit 470805eb9f ("ASoC: tegra:
Convert to managed resources"). Before this commit, PM cleanup was
performed after the component was unregistered. But returning
directly will skip PM cleanup. So, to be on safe side it is better
to use snd_soc_register_component instead of
devm_snd_soc_register_component.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If DMA interrupt comes and is latched by IRQ controller during the
execution of dma_terminate_all(), dma_irq routine will be executed
after dma terminated, and it will cause kernel panic.
We clear DMA interrupts in dma_terminate_all() to avoid this useless
interrupt.
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add device tree bindings documentation for the
lpc1850-dmamux DMA router.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA on NXP LPC18xx/43xx platforms which has
a multiplexer in front of the PL080 dma request lines.
The mux is a single register in the LPC18xx/43xx CREG block
and can multiplex up to 4 request lines to each of the 16
lines on the PL080.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This introduces device tree bindings for the PL08x DMA controllers
when used with fixed signal assignment per channel, i.e. if each
channel on the PL08x is assigned precisely one burst/single signal
set.
[je: remove channel sub-node parsing, use cell value to assign AHB]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following error:
drivers/dma/pxa_dma.c: In function ‘dbg_show_requester_chan’:
drivers/dma/pxa_dma.c:192:2: error: void value not ignored as it ought to be
pos += seq_printf(s, "DMA channel %d requester :\n", phy->idx);
^
drivers/dma/pxa_dma.c:197:8: error: void value not ignored as it ought to be
!!(drcmr & DRCMR_MAPVLD));
^
scripts/Makefile.build:258: recipe for target 'drivers/dma/pxa_dma.o' failed
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The variable called "this_base" is confusing because its name suggests
it's of "struct hrtimer_clock_base" type, along with "base" and "new_base"
which doesn't help understanding this complicated function.
Make its name clearer and fix the misleading comment while at it.
[ tglx: Fixed the comment for real ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1439907509-9553-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the topology API is still in sufficient flux for changes to be
identified disable the use of the userspace ABI by adding #error
statements to the code, ensuring that nobody relies on the headers as
currently defined. It is expected that this change will be reverted for
v4.3.
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_readable() returns false if map->format.format_write is set.
For .reg_bits = 7, .val_bits = 9, setting,
map->format.format_write = regmap_format_7_9_write;
Even current code has implemented map->readable_reg, regmap_readable()
still returns false anyway. Thus drop the misleading readable_reg callback
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Alex Deucher, Mark Rustad and Alexander Holler reported a regression
with the latest v4.2-rc4 kernel, which breaks some SATA controllers.
With multi-MSI capable SATA controllers, only the first port works,
all other ports time out when executing SATA commands.
This happens because the first argument to assign_irq_vector_policy()
is always the base linux irq number of the multi MSI interrupt block,
so all subsequent vector assignments operate on the base linux irq
number, so all MSI irqs are handled as the first irq number. Therefor
the other MSI irqs of a device are never set up correctly and never
fire.
Add the loop iterator to the base irq number so all vectors are
assigned correctly.
Fixes: b5dc8e6c21 "x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors"
Reported-and-tested-by: Alex Deucher <alexdeucher@gmail.com>
Reported-and-tested-by: Mark Rustad <mrustad@gmail.com>
Reported-and-tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439911228-9880-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The logic in nvme_dev_add to enumerate namespaces was moved to
nvme_dev_scan. When moved, the nn variable is no longer used. This patch
removes it.
Fixes: a5768aai ("NVMe: Automatic namespace rescan")
Signed-off-by: Matias Bjørling <m@bjorling.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There's a typo in commit e39758e0ea in linux-next, which incorrectly
spells "msi_desc_to_pci_sysdata()" as "msi_desc_to_pci_sys_data()" and
causes build failure:
> ../drivers/pci/host/pcie-xilinx.c:235:3: error: implicit declaration
of function 'msi_desc_to_pci_sys_data' [-Werror=implicit-function-declaration]
Fixes: e39758e0ea "PCI: Use helper functions to access fields in struct msi_desc"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Srikanth Thokala <sthokal@xilinx.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Link: http://lkml.kernel.org/r/1439912763-10645-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__blkdev_issue_discard_async() doesn't need to worry about further
splitting because the upper layer blkdev_issue_discard() will have
already handled splitting bios such that the bi_size isn't
overflowed.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
The routines in scsi_rpm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by calling the block layer's runtime-PM
routines only if the device's driver really does have a runtime-PM
callback routine. Since ses doesn't define any such callbacks, the
crash won't occur.
This fixes Bugzilla #101371.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stanisław Pitucha <viraptor@gmail.com>
Reported-by: Ilan Cohen <ilanco@gmail.com>
Tested-by: Ilan Cohen <ilanco@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We added changes in fnic driver patch 1.6.0.16 to acquire
io_req_lock in fnic_queuecommand() before issuing I/O so that io completion
is serialized. But when releasing the lock we check for the I/O flag and
this could be modified if IO abort occurs before I/O completion. In this case
we wont release the lock and causes deadlock in some scenerios. Using the
local variable to check the IO lock status will resolve the problem.
Fixes: 41df7b02db
Signed-off-by: Hiral Shah <hishah@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Anil Chintalapati <achintal@cisco.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull drm fixes from Dave Airlie:
"These came in late last week, I wanted to look over the mst one before
forwarding, but it seems good.
Just three i915 and one MST fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
drm/dp/mst: Remove port after removing connector.
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV0uQxAAoJEC0Llv5uNjIBA3MQAKrYe0QQlty150wuXaJwys/1
CmdtcVSytafaCPchmPL4O73m8Z5kGv9yhktyY9dYGexMkgiqInzHRo3IWIO0eTFQ
83xrwdplxbv2j1gs6peNT5ojsXDVawiFcrAKbM3SXFyUTZCblnjPGXledmMH3S+f
L3cypj4j97HhyGnksm5kOiH+3LOfS/+JWW6LS9Z1/nEuehrykS1v5noUhgntlmTq
jy2BlocQxEKe89o1bbaG8s3BEL8l5O+Te4z7bhV0k/aX/jzcybQOf0bX+5nUswq/
YoZtHapd9vS6/z/dZiohDS4Db8HwqXjiFTgGhwu8lsxiI828pZlnBubNoSfsacyh
6UDXEqfP8bFcmWUf5vrG9eabxU008CBZ4pEuXHH/JV3DB9PRHVZ+bXtznMqzJtI0
1B0Mlc+iXB2sBhQqzMjinRM395cLipIhImriBfYDHoa/NiUIeZYTYwmwTdwWVXzh
d1OgtiqPRZMpWISON6/hcOARthOwj4per4Dieoy1vdyXhS2Fbz6edxIo4E2XW89C
AgWtJnsvZ1uTOhb/Ei6xiTtYEW9k8Dkb8i5SmcpZBNHAxLhD2SiNR4ZFLfUyluLB
eauZEDIcCoeCj+itYD4mguQlQHMlTcn+qaKXnWZWpTxUObkJpb2JUzaoyfJtka1F
ZrMX6X4dVmL6nJqL6rb7
=9i6F
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-18' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
lock_timer_base() cannot prevent the following :
CPU1 ( in __mod_timer()
timer->flags |= TIMER_MIGRATING;
spin_unlock(&base->lock);
base = new_base;
spin_lock(&base->lock);
// The next line clears TIMER_MIGRATING
timer->flags &= ~TIMER_BASEMASK;
CPU2 (in lock_timer_base())
see timer base is cpu0 base
spin_lock_irqsave(&base->lock, *flags);
if (timer->flags == tf)
return base; // oops, wrong base
timer->flags |= base->cpu // too late
We must write timer->flags in one go, otherwise we can fool other cpus.
Fixes: bc7a34b8b9 ("timer: Reduce timer migration overhead if disabled")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Christopherson <jon@jons.org>
Cc: David Miller <davem@davemloft.net>
Cc: xen-devel@lists.xen.org
Cc: david.vrabel@citrix.com
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Link: http://lkml.kernel.org/r/1439831928.32680.11.camel@edumazet-glaptop2.roam.corp.google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Enabling irq wake could potentially fail and calling disable_irq_wake
after a failed call to enable_irq_wake could result in an unbalanced irq
warning. This patch warns if enable_irq_wake fails and avoids other
potential issues caused by calling disable_irq_wake on resume after
enable_irq_wake failed during suspend.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current generation of "Intuos" tablets (i.e. INTUOSHT) report touch
width and height data just like the "Intuos Pro" do. This commit changes
the code to allow these tablets to use the appropriate codepath instead
of the one intended for Intuos5/Bamboo.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This gamepad advertise 5 absolute axis while 4 are actually used.
The second Z axis shows some garbage, so it has to be ignored by HID.
The first Z axis and the Rz one are actually Rx and Ry. Remap them.
We could also just remap and ignore the axis in .input_mapping(). I
went ahead with .report_fixup() first, so here it is.
Reported-by: Orivej Desh <orivej@gmx.fr>
Tested-by: Orivej Desh <orivej@gmx.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All architectures except arm that define DMA_ERROR_CODE are casting it
to (dma_addr_t) - as it is always compared to dma_addr_t in arm as well
this could be harmonized.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use BIT_MASK() and BIT_WORD() rather than hard-coding the size
of the "long" type.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The chain of of_address_to_resource() and ioremap() can be replaced
with of_iomap().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add early fixmap support, initially to support permanent, fixed
mapping support for early console. A temporary, early pte is
created which is migrated to a permanent mapping in paging_init.
This is also needed since the attributes may change as the memory
types are initialized. The 3MiB range of fixmap spans two pte
tables, but currently only one pte is created for early fixmap
support.
Re-add FIX_KMAP_BEGIN to the index calculation in highmem.c since
the index for kmap does not start at zero anymore. This reverts
4221e2e6b3 ("ARM: 8031/1: fixmap: remove FIX_KMAP_BEGIN and
FIX_KMAP_END") to some extent.
Cc: Mark Salter <msalter@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
U-Boot is often used to boot the kernel on ARM boards, but uImage
is not built by "make all", so we are often inclined to do
"make all uImage" to generate DTBs, modules and uImage in a single
command, but we should notice a pitfall behind it. In fact,
"make all uImage" could generate an invalid uImage if it is run with
the parallel option (-j).
You can reproduce this problem with the following procedure:
[1] First, build "all" and "uImage" separately.
You will get a valid uImage
$ git clean -f -x -d
$ export CROSS_COMPILE=<your-tools-prefix>
$ make -s -j8 ARCH=arm multi_v7_defconfig
$ make -s -j8 ARCH=arm all
$ make -j8 ARCH=arm UIMAGE_LOADADDR=0x80208000 uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CHK include/generated/timeconst.h
CHK include/generated/bounds.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
UIMAGE arch/arm/boot/uImage
Image Name: Linux-4.2.0-rc5-00156-gdd2384a-d
Created: Sat Aug 8 23:21:35 2015
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6138648 Bytes = 5994.77 kB = 5.85 MB
Load Address: 80208000
Entry Point: 80208000
Image arch/arm/boot/uImage is ready
$ ls -l arch/arm/boot/*Image
-rwxrwxr-x 1 masahiro masahiro 13766656 Aug 8 23:20 arch/arm/boot/Image
-rw-rw-r-- 1 masahiro masahiro 6138712 Aug 8 23:21 arch/arm/boot/uImage
-rwxrwxr-x 1 masahiro masahiro 6138648 Aug 8 23:20 arch/arm/boot/zImage
[2] Update some source file(s)
$ touch init/main.c
[3] Then, re-build "all" and "uImage" simultaneously.
You will get an invalid uImage at random.
$ make -j8 ARCH=arm UIMAGE_LOADADDR=0x80208000 all uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CHK include/generated/timeconst.h
CHK include/generated/bounds.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CC init/main.o
CHK include/generated/compile.h
LD init/built-in.o
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
KSYM .tmp_kallsyms1.o
KSYM .tmp_kallsyms2.o
LD vmlinux
SORTEX vmlinux
SYSMAP System.map
OBJCOPY arch/arm/boot/Image
Building modules, stage 2.
Kernel: arch/arm/boot/Image is ready
GZIP arch/arm/boot/compressed/piggy.gzip
AS arch/arm/boot/compressed/piggy.gzip.o
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
GZIP arch/arm/boot/compressed/piggy.gzip
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
UIMAGE arch/arm/boot/uImage
Image Name: Linux-4.2.0-rc5-00156-gdd2384a-d
Created: Sat Aug 8 23:23:14 2015
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 26472 Bytes = 25.85 kB = 0.03 MB
Load Address: 80208000
Entry Point: 80208000
Image arch/arm/boot/uImage is ready
MODPOST 192 modules
AS arch/arm/boot/compressed/piggy.gzip.o
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
$ ls -l arch/arm/boot/*Image
-rwxrwxr-x 1 masahiro masahiro 13766656 Aug 8 23:23 arch/arm/boot/Image
-rw-rw-r-- 1 masahiro masahiro 26536 Aug 8 23:23 arch/arm/boot/uImage
-rwxrwxr-x 1 masahiro masahiro 6138648 Aug 8 23:23 arch/arm/boot/zImage
Please notice the uImage is extremely small when this issue is
encountered. Besides, "Kernel: arch/arm/boot/zImage is ready" is
displayed twice, before and after the uImage log.
The root cause of this is the race condition between zImage and
uImage. Actually, uImage depends on zImage, but the dependency
between the two is only described in arch/arm/boot/Makefile.
Because arch/arm/boot/Makefile is not included from the top-level
Makefile, it cannot know the dependency between zImage and uImage.
Consequently, when we run make with the parallel option, Kbuild
updates vmlinux first, and then two different threads descends into
the arch/arm/boot/Makefile almost at the same time, one for updating
zImage and the other for uImage. While one thread is re-generating
zImage, the other also tries to update zImage before creating uImage
on top of that. zImage is overwritten by the slower thread and then
uImage is created based on the half-written zImage.
This is the reason why "Kernel: arch/arm/boot/zImage is ready" is
displayed twice, and a broken uImage is created.
The same problem could happen on bootpImage.
This commit adds dependencies among Image, zImage, uImage, and
bootpImage to arch/arm/Makefile, which is included from the
top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmap semaphore should not be taken when page faults are disabled.
Since pagefault_disable() no longer disables preemption, we now need
to use faulthandler_disabled() in place of in_atomic().
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a function to find the start of the SADs in the ELD. This
complements the helper to retrieve the SAD count.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Matthew Fortune <Matthew.Fortune@imgtec.com> reports:
The genex.S file appears to mix the case of a macro between its definition and
use. A cut down example of this is below. The macro __build_clear_none has
lower case 'build' but ends up being instantiated with upper case BUILD. Can
this be fixed on master. It has been picked up by the LLVM integrated assembler
which is currently case sensitive. We are likely to fix the assembler as well
but the code is currently inconsistent in the kernel.
.macro __build_clear_none
.endm
.macro __BUILD_HANDLER exception handler clear verbose ext
.align 5
.globl handle_\exception; .align 2; .type handle_\exception, @function; .ent
handle_\exception, 0; handle_\exception: .frame $29, 184, $29
.set noat
.globl handle_\exception\ext; .type handle_\exception\ext, @function;
handle_\exception\ext:
__BUILD_clear_\clear
.endm
.macro BUILD_HANDLER exception handler clear verbose
__BUILD_HANDLER \exception \handler \clear \verbose _int
.endm
BUILD_HANDLER ftlb ftlb none silent
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Matthew Fortune <Matthew.Fortune@imgtec.com>
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
