commit 90f91b1298 upstream.
It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 300f77c08d upstream.
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb686231fc upstream.
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 31a418986a upstream.
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ce0e5c522d upstream.
Commit e9ce7cb6b1 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a935865c82 upstream.
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 397a253af5 upstream.
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7e14069651 upstream.
RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.
This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.
Fixes: a59a4d1921 ("phy: add the EEE support and the way to access to the MMD registers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ea345c145f upstream.
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 44f6731d8b upstream.
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2439fc4d71 upstream.
adapter->tx_ring is set to NULL where rx_ring should be.
Fixes: 5536d2102a ("igb: Combine q_vector and ring allocation into a single function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c0a06ee185 upstream.
When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.
- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
misleads igb_poll() to determine that it has an rx ring although it
actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
(q_vector->ring[0].skb) has a value that was used as tx_stats before.
Fix these problems by zeroing it out on reuseing it.
Fixes: 02ef6e1d0b ("igb: Fix queue allocation method to accommodate changing during runtime")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5793affe8c upstream.
Using IDR_SRR in RXFIFO_ID to test for the presence of data is only
valid for standard frames. For extended frames the bit is always 1 and
IDR_RTR should be used instead. This patch switches the check to use
CAN_RTR_FLAG which is correctly set when reading the ID.
The patch also changes the DW1/DW2 to be read unconditionally, since
this is necessary to remove the frame from the RXFIFO.
Signed-off-by: Jeppe Ledet-Pedersen <jlp@gomspace.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 414b7e3b9c upstream.
The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to
usb_control_msg() with a timeout value of 0. In some instances where the
interface is shutting down, this infinite wait results in a CPU deadlock. A
one second timeout fixes this problem without affecting any normal operations.
This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786.
Reported-by: Bernhard Wiedemann <bwiedemann@suse.com>
Tested-by: Bernhard Wiedemann <bwiedemann@suse.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bernhard Wiedemann <bwiedemann@suse.com>
Cc: Takashi Iwai<tiwai@suse.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f94813f3c1 upstream.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e7 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 07841f9d94 upstream.
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 42eab005a5 upstream.
By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Ido Shamay <idos@mellanox.com>
Fixes: d03a68f ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 59d2d18cc4 upstream.
If CONFIG_ARCH_DMA_ADDR_T_64BIT enabled for x86 systems and physical
memory is more than 4GB, dma_map_page may return a valid memory
address which greater than 0xffffffff. As a result, the mlx5 device page
allocator RB tree will be initialized with valid addresses greater than
0xfffffff.
However, (addr & PAGE_MASK) set the high four bytes to zeros. So, it's
impossible for the function, free_4k, to release the pages whose
addresses greater than 4GB. Memory leaks. And mlx5_ib module can't
release the pages when user try to remove the module, as a result,
system hang.
[root@rdma05 root]# dmesg | grep addr | head
addr = 3fe384000
addr & PAGE_MASK = fe384000
[root@rdma05 root]# rmmod mlx5_ib <---- hang on
---------------------- cosnole log -----------------
mlx5_ib 0000:04:00.0: irq 138 for MSI/MSI-X
alloc irq_desc for 139 on node -1
alloc kstat_irqs on node -1
mlx5_ib 0000:04:00.0: irq 139 for MSI/MSI-X
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
---------------------- cosnole log -----------------
Fixes: bf0bf77f65 ('mlx5: Support communicating arbitrary host page size to firmware')
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a3fa71c40f upstream.
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e8 ("wl18xx: use new fw stats structures")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 08e8331654 upstream.
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
[...]
Call Trace:
[<ffffffff81195445>] put_page+0x55/0x60
[<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
[<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
[<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
[<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
[<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
[<ffffffff81647050>] dev_set_mtu+0xa0/0x140
[<ffffffff81664218>] do_setlink+0x218/0xac0
[<ffffffff814459e9>] ? nla_parse+0xb9/0x120
[<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
[<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
[<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260
By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers. The allocator is set back to a sane value in
e1000_configure_rx.
Fixes: edbbb3ca10 ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2f92b314f4 upstream.
USB ID 2001:330d is used for a D-Link DWA-131.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9374e7d2fd upstream.
Add new ID for ASUS N10 WiFi dongle.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3dfb05340e upstream.
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f5e2dc5d7f upstream.
Before commit 3900f29021 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.
The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7a1e890e21 upstream.
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1e9e39f4a2 upstream.
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0c36820e2a upstream.
xen-netfront limits transmitted skbs to be at most 44 segments in size. However,
GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448
bytes each. This slight reduction in the size of packets means a slight loss in
efficiency.
Since c/s 9ecd1a75d, xen-netfront sets gso_max_size to
XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER,
where XEN_NETIF_MAX_TX_SIZE is 65535 bytes.
The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s
6c09fa09d) in determining when to split an skb into two is
sk->sk_gso_max_size - 1 - MAX_TCP_HEADER.
So the maximum permitted size of an skb is calculated to be
(XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER.
Intuitively, this looks like the wrong formula -- we don't need two TCP headers.
Instead, there is no need to deviate from the default gso_max_size of 65536 as
this already accommodates the size of the header.
Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments
of 1448 bytes each), as observed via tcpdump. This patch makes netfront send
skbs of up to 65160 bytes (45 segments of 1448 bytes each).
Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as
it relates to the size of the whole packet, including the header.
Fixes: 9ecd1a75d9 ("xen-netfront: reduce gso_max_size to account for max TCP header")
Signed-off-by: Jonathan Davies <jonathan.davies@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e5eda89d97 upstream.
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0cc ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 555828ef45 upstream.
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9c8928f517 upstream.
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 87f966d97b upstream.
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a9dc960c37 upstream.
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8d006e0105 upstream.
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2fec5104f9 upstream.
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit deb2701cf7 upstream.
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 969439016d upstream.
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit da29370056 upstream.
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 61132bf7fb upstream.
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d3 ("qlge: Enhance nested VLAN (Q-in-Q) handling.")
Cc: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8bfae4f993 upstream.
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbe ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbe ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9215f437b8 upstream.
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 42c972a1f3 upstream.
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2f1d8b9e8a upstream.
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 57e5956319 upstream.
Currently following race is possible in team:
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 54da5a8be3 upstream.
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34 ("net: phy: fix a bug when verify the EEE support")
Fixes: 3e7077067e ("phy: Expand phy speed/duplex settings array")
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8997c27ec4 upstream.
src_net points to the netns where the netlink message has been received. This
netns may be different from the netns where the interface is created (because
the user may add IFLA_NET_NS_[PID|FD]). In this case, src_net is the link netns.
It seems wrong to override the netns in the newlink() handler because if it
was not already src_net, it means that the user explicitly asks to create the
netdevice in another netns.
CC: Sjur Brændeland <sjur.brandeland@stericsson.com>
CC: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Fixes: 8391c4aab1 ("caif: Bugfixes in CAIF netdevice for close and flow control")
Fixes: c412540063 ("caif-hsi: Add rtnl support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit fd66fc1caf upstream.
When iwl_mvm_power_update_mac() is called, we have already added the
mac context, so if this call fails we should remove the mac.
Fixes: commit e5e7aa8e25 ('iwlwifi: mvm: refactor power code')
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cd8f438405 upstream.
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5523d11cc4 upstream.
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2cee4762c5 upstream.
These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d953ca4ddf upstream.
The existing code frees the skb in EAGAIN case, in which the skb will be
retried from upper layer and used again.
Also, the existing code doesn't free send buffer slot in error case, because
there is no completion message for unsent packets.
This patch fixes these problems.
(Please also include this patch for stable trees. Thanks!)
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
