The controller driver nacked the master request but didn't emit a
STOP to end the transaction. The driver shall refuse the unsupported
requests and return the controller state to IDLE by emitting a STOP.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-4-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The target can send the MDB byte followed by additional data bytes.
The readl on MRDATAB reads one actual byte, but the readsl advances
the destination pointer by 4 bytes. This causes the subsequent payload
to be copied to wrong position in the destination buffer.
Cc: stable@kernel.org
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The code does not add IBI rules for devices with controller capability.
However, the secondary controller has the controller capability and works
at target mode when the device is probed. Therefore, add IBI rules for
such devices.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use asm_inline for all inline assemblies which make use of the EX_TABLE or
ALTERNATIVE macros.
These macros expand to many lines and the compiler assumes the number of
lines within an inline assembly is the same as the number of instructions
within an inline assembly. This has an effect on inlining and loop
unrolling decisions.
In order to avoid incorrect assumptions use asm_inline, which tells the
compiler that an inline assembly has the smallest possible size.
In order to avoid confusion when asm_inline should be used or not, since a
couple of inline assemblies are quite large: the rule is to always use
asm_inline whenever the EX_TABLE or ALTERNATIVE macro is used. In specific
cases there may be reasons to not follow this guideline, but that should
be documented with the corresponding code.
Using the inline qualifier everywhere has only a small effect on the kernel
image size:
add/remove: 0/10 grow/shrink: 19/8 up/down: 1492/-1858 (-366)
The only location where this seems to matter is load_unaligned_zeropad()
from word-at-a-time.h where the compiler inlines more functions within the
dcache code, which is indeed code where performance matters.
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit d08d4e7cd6 ("s390/mm: use full 4KB page for 2KB PTE"),
there is no longer any reason to avoid splitting the kfence pool into
4k mappings in arch_kfence_init_pool(). Remove the architecture-specific
kfence_split_mapping().
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With recent ftrace changes, argument tracing has been added to the
function tracer. As a result, ftrace opportunistically reads the first
FTRACE_REGS_MAX_ARGS (i.e., 6) registers. On s390, only five arguments are
passed in registers, and the 6-th is read from the stack. If a function
has fewer than 6 arguments, the following KASAN report may be observed:
BUG: KASAN: stack-out-of-bounds in regs_get_kernel_stack_nth+0xa8/0xb0
Read of size 8 at addr 00007f7fe066fdb8 by task swapper/31/0
CPU: 31 UID: 0 PID: 0 Comm: swapper/31 Not tainted 6.14.0-rc4-00006-g76fe0337c219 #16
Hardware name: IBM 3931 A01 704 (KVM/Linux)
Call Trace:
[<00007fffe0147224>] dump_stack_lvl+0x104/0x168
[<00007fffe011381c>] print_address_description.constprop.0+0x34/0x338
[<00007fffe0113b64>] print_report+0x44/0x138
[<00007fffe0ad9422>] kasan_report+0xc2/0x180
[<00007fffe0159ff8>] regs_get_kernel_stack_nth+0xa8/0xb0
[<00007fffe05ebeda>] trace_function+0x23a/0x4d0
[<00007fffe0615d32>] irqsoff_tracer_call+0xd2/0x110
[<00007fffe2b4e34c>] ftrace_common+0x1c/0x40
[<00007fffe0150826>] arch_cpu_idle_enter+0x6/0x10
[<00007fffe035a1c8>] do_idle+0x168/0x2e0
[<00007fffe035a9d0>] cpu_startup_entry+0x90/0xb0
[<00007fffe017d25a>] smp_start_secondary+0x3da/0x4e0
[<00007fffe2b4e20a>] restart_int_handler+0x72/0x88
no locks held by swapper/31/0.
The buggy address belongs to stack of task swapper/31/0
and is located at offset 0 in frame:
do_idle+0x0/0x2e0
This frame has 1 object:
[32, 40) '__mask'
The buggy address belongs to the virtual mapping at
[00007f7fe0660000, 00007f7fe0671000) created by:
dup_task_struct+0x66/0x4e0
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x80f23
flags: 0x3ffff00000000000(node=0|zone=1|lastcpupid=0x1ffff)
raw: 3ffff00000000000 0000000000000000 0000000000000122 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffff00000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
00007f7fe066fc80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00007f7fe066fd00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>00007f7fe066fd80: 00 00 00 00 00 00 00 f1 f1 f1 f1 00 f3 f3 f3 00
^
00007f7fe066fe00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00007f7fe066fe80: 00 f1 f1 f1 f1 00 f2 f2 f2 00 00 f3 f3 00 00 00
The function regs_get_kernel_stack_nth() verifies that the requested
argument is located on the stack, making it safe to read even if it is
not actually present. Make use of READ_ONCE_NOCHECK() helper to silence
KASAN reports in this case.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When building with CONFIG_VMLINUX_MAP=y, a decompressor vmlinux.map file
is generated in the boot directory.
Add this file to .gitignore to ensure Git does not track it.
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/F884C733016D6715+20250311030824.675683-1-wangyuli@uniontech.com
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove the not needed "vm/allocate_pgste" sysctl. It has no effect
anymore. However this is a user space visible change. It shouldn't cause
any problems, however if it does this needs to be partially reverted.
Note that some distributions set
vm/allocate_pgste=1
in one of the various sysctl configuration files. Besides a warning about
the (now) non-existent procfs file this doesn't cause any problems.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit d08d4e7cd6 ("s390/mm: use full 4KB page for 2KB PTE") always
4k page tables are allocated, however there is still some (now) obsolete
code left which deals with switching from 2k to 4k page tables for qemu/kvm
processes.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Remove the not needed code.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
An mm has pgstes only after s390_enable_sie() has been called, while
mm_alloc_pgste() may be always true (e.g. via sysctl setting).
Limit the calls to gmap_unlink() in pte_free_tlb() to those cases
where there might be something to unlink.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
lghi is the fastest way to clear a register. Use that intead of llilh.
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The compiler inlines do_syscall() into __do_syscall(). Therefore do this in
C code as well, since this makes the code easier to understand.
Also adjust and add various unlikely() and likely() annotations.
Furthermore this allows to replace the separate exit_to_user_mode() and
syscall_exit_to_user_mode_work() calls with a combined
syscall_exit_to_user_mode() call which results in slightly better code.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Implement SPINLOCK_LOCKVAL with an inline assembly, which makes use of the
ALTERNATIVE macro, to read spinlock_lockval from lowcore. Provide an
alternative instruction with a different offset in case lowcore is
relocated.
This replaces sequences of two instructions with one instruction.
Before:
10602a: a7 78 00 00 lhi %r7,0
10602e: a5 8e 00 00 llilh %r8,0
106032: 58 d0 83 ac l %r13,940(%r8)
106036: ba 7d b5 80 cs %r7,%r13,1408(%r11)
After:
10602a: a7 88 00 00 lhi %r8,0
10602e: e3 70 03 ac 00 58 ly %r7,940
106034: ba 87 b5 80 cs %r8,%r7,1408(%r11)
Kernel image size change:
add/remove: 756/750 grow/shrink: 646/3435 up/down: 30778/-46326 (-15548)
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Implement raw_smp_processor_id() with an inline assembly, which makes
use of the ALTERNATIVE macro, to read cpu_nr from lowcore. Provide an
alternative instruction with a different offset in case lowcore is
relocated.
This replaces sequences of two instructions with one instruction.
Before:
1000b6: a5 1e 00 00 llilh %r1,0
1000ba: 58 20 13 a0 l %r2,928(%r1)
After:
1000b6: e3 20 03 a0 00 58 ly %r2,928
Kernel image size change:
add/remove: 753/755 grow/shrink: 230/1510 up/down: 30538/-35832 (-5294)
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Implement current with an inline assembly, which makes use of the
ALTERNATIVE macro, to read current from lowcore. Provide an alternative
instruction with a different offset in case lowcore is relocated.
This replaces sequences of two instructions with one instruction.
Before:
100076: a5 1e 00 00 llilh %r1,0
10007a: e3 40 13 40 00 04 lg %r4,832(%r1)
After:
100076: e3 10 03 40 00 04 lg %r1,832
Kernel image size change:
add/remove: 3/17 grow/shrink: 166/2204 up/down: 7122/-24594 (-17472)
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use asm_inline to let the compiler know that the get_lowcore() inline
assembly has the smallest possible size. The ALTERNATIVE construct is used
to generate a single instruction, however the macro expands to multiple
lines. GCC uses the number of lines of an inline assembly to count the
number of instructions within an inline assembly, which then has an effect
on inlining decisions.
In order to avoid incorrect assumptions use asm_inline. The result is that
more functions are inlined, which results in a small growth of the kernel
image:
add/remove: 59/480 grow/shrink: 854/647 up/down: 168780/-162394 (6386)
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move s390 sysctls (spin_retry and userprocess_debug) into their own
files under arch/s390. Create two new sysctl tables
(2390_{fault,spin}_sysctl_table) which will be initialized with
arch_initcall placing them after their original place in proc_root_init.
This is part of a greater effort to move ctl tables into their
respective subsystems which will reduce the merge conflicts in
kernel/sysctl.c.
Signed-off-by: joel granados <joel.granados@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250306-jag-mv_ctltables-v2-6-71b243c8d3f8@kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Let's assume all these macros should not have a trailing comma, this way
the caller can use a more formal and usual C writing style, as reflected
in the Macronix driver.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch bypasses multi-link errors in TCP mode, allowing dlm
to operate on the first tcp link.
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Merge series from wangweidong.a@awinic.com:
Add the awinic,aw88166 property to support the aw88166 chip.
The driver is for amplifiers aw88166 of Awinic Technology
Corporation. The AW88166 is a high efficiency digital
Smart K audio amplifier
Merge series from Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>:
Add sof support on imx95. This series also includes some changes to
the audio-graph-card2 binding required for the support.
Merge series from Ethan Carter Edwards <ethan@ethancedwards.com>:
Open coded arithmetic in allocator arguments is discouraged. Helper
functions like kcalloc or, in this case, devm_kcalloc are preferred. Not
only for readability purposes but safety purposes.
The changes move `devm_kzalloc(dev, sizeof(var) * n, GFP_KERNEL)` to
the helper function `devm_kcalloc(dev, n, sizeof(var), GFP_KERNEL)`.
Here is a series of four patches within the Intel/avs drivers that make
these changes. They are all compile tested only but should have no
effect on runtime behaviour.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Link: https://github.com/KSPP/linux/issues/162
Add base support for HTU31 temperature and humidity sensor.
Besides temperature and humidity values, the driver also exports a 24-bit
heater control to sysfs and serial number to debugfs.
Signed-off-by: Andrei Lalaev <andrey.lalaev@gmail.com>
Link: https://lore.kernel.org/r/20250217051110.46827-2-andrey.lalaev@gmail.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add trivial binding for HTU31 Temperature and Humidity sensor.
Signed-off-by: Andrei Lalaev <andrey.lalaev@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250217051110.46827-3-andrey.lalaev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Russell King says:
====================
net: stmmac: remove unnecessary of_get_phy_mode() calls
This series removes unnecessary of_get_phy_mode() calls from the stmmac
glue drivers. stmmac_probe_config_dt() / devm_stmmac_probe_config_dt()
already gets the interface mode using device_get_phy_mode() and stores
it in plat_dat->phy_interface.
Therefore, glue drivers using of_get_phy_mode() are just duplicating
the work that has already been done.
This series adjusts the glue drivers to remove their usage of
of_get_phy_mode().
====================
Link: https://patch.msgid.link/Z9FQjQZb0IMaQJ9H@shell.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set gmac->interface from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGx-005v0F-Ev@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
sun8i was using of_get_phy_mode() to set plat_dat->mac_interface, which
defaults to plat_dat->phy_interface when the mac-mode DT property is
not present. As nothing in arch/*/boot/dts sets the mac-mode property,
it is highly likely that these two will be identical, and thus there
is no need for this glue driver to set plat_dat->mac_interface.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGs-005v09-CD@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Pass plat_dat into sti_dwmac_parse_data(), and set dwmac->interface
from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGn-005v02-7G@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set bsp_priv->phy_iface from plat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGi-005uzx-3p@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set dwmac->phy_mode from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGd-005uzr-0C@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Pass plat_dat into ipq806x_gmac_of_parse(), and set gmac->phy_mode from
plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGX-005uzl-TQ@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Rearrange the initialisation order so we can pass plat_dat into
anarion_config_dt(), thereby providing plat_dat->phy_interface as
necessary there.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGS-005uzf-QE@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Initialise priv_plat->phy_mode from plat->phy_interface
inmediatek_dwmac_common_data().
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGN-005uzZ-NG@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it a second time in qcom_ethqos_probe(). Use
plat_dat->phy_interface to initialise ethqos->phy_mode.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIGI-005uzT-KB@rmk-PC.armlinux.org.uk
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge series from Dan Carpenter <dan.carpenter@linaro.org>:
Here are two fixes for Smatch warnings.
Dan Carpenter (2):
spi: sg2044-nor: fix signedness bug in sg2044_spifmc_write()
spi: sg2044-nor: Fix uninitialized variable in probe
drivers/spi/spi-sg2044-nor.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
--
2.47.2
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The unhashed state check in __wait_on_freeing_inode() performed with
->i_lock held against remove_hash_inode() also holding the lock makes
another lock acquire in evict() completely spurious -- all potential
sleepers already dropped the lock before remove_hash_inode() acquired
it or they found the inode to be unhashed and aborted.
Note there is no trickery here: the usual cost of both sides taking
locks is still being paid, it just stops being paid twice.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://lore.kernel.org/r/20250317160707.1694135-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
The routine is used a lot, while the wakeup almost never has anyone to
deal with.
wake_up_all() takes an irq-protected spinlock, wq_has_sleeper() "only"
contains a full fence -- not free by any means, but still cheaper.
Sample result tracing waiters using a custom probe during -j 20 kernel
build (0 - no waiters, 1 - waiters):
@[
wakeprobe+5
__wake_up_common+63
__wake_up+54
__d_add+234
d_splice_alias+146
ext4_lookup+439
path_openat+1746
do_filp_open+195
do_sys_openat2+153
__x64_sys_openat+86
do_syscall_64+82
entry_SYSCALL_64_after_hwframe+118
]:
[0, 1) 13999 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[1, ...) 1 | |
Only 1 call out of 14000 with this backtrace had waiters.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://lore.kernel.org/r/20250316232421.1642758-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
try_lookup_one_len() is identical to lookup_one_unlocked() except that
it doesn't include the call to lookup_slow(). The latter doesn't need
the inode to be locked, so the former cannot either.
So fix the documentation, remove the WARN_ON and fix the only caller to
not take the lock.
Signed-off-by: NeilBrown <neilb@suse.de>
Link: https://lore.kernel.org/r/174190517441.9342.5956460781380903128@noble.neil.brown.name
Signed-off-by: Christian Brauner <brauner@kernel.org>
... except when the table is known to be only used by one thread.
A file pointer can get installed at any moment despite the ->file_lock
being held since the following:
8a81252b77 ("fs/file.c: don't acquire files->file_lock in fd_install()")
Accesses subject to such a race can in principle suffer load tearing.
While here redo the comment in dup_fd -- it only covered a race against
files showing up, still assuming fd_install() takes the lock.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://lore.kernel.org/r/20250313135725.1320914-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Sanju is no longer with AMD. Update the MAINTAINERS file record.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The function call “dmaengine_unmap_put(unmap)” was used in an if branch.
The same call was immediately triggered by a subsequent goto statement.
Thus avoid such a call repetition.
This issue was detected by using the Coccinelle software.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The AMD Image Signal Processor GPIO pin control functionality is only
present on AMD platforms with ISP support, and its platform device is
instantiated by the AMD ISP driver. Hence add a dependency on
DRM_AMD_ISP, to prevent asking the user about this driver when
configuring a kernel that does not support the AMD ISP.
Fixes: e97435ab09 ("pinctrl: amd: isp411: Add amdisp GPIO pinctrl")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/3685561e8e3cd1d94bce220eeb6001d659da615c.1742306024.git.geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure we are not using DB's which were remapped for link status.
Fixes: f6e51c354b ("ntb: intel: split out the gen3 code")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT.
Fixes: 1e2fd202f8 ("ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
At the moment it's a little unclear where initramfs patches should be
sent. This should see them end up on the linux-fsdevel mailing list.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Link: https://lore.kernel.org/r/20250318040711.20683-1-ddiss@suse.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
Currently, fgraph on riscv relies on the infrastructure of
DYNAMIC_FTRACE_WITH_ARGS. However, DYNAMIC_FTRACE_WITH_ARGS may be
turned off on riscv, which will cause the enabled fgraph to be abnormal.
Therefore, let's select HAVE_FUNCTION_GRAPH_TRACER depends on
HAVE_DYNAMIC_FTRACE_WITH_ARGS.
Fixes: a3ed4157b7 ("fgraph: Replace fgraph_ret_regs with ftrace_regs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503160820.dvqMpH0g-lkp@intel.com/
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20250317031214.4138436-1-pulehui@huaweicloud.com
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
If vfs_flush() is called with queue frozen, the queue freeze lock may be
connected with FS internal lock, and lockdep warning can be triggered
because the queue freeze lock is connected with too many global or
sub-system locks.
Fix the warning by moving vfs_fsync() out of loop_update_dio():
- vfs_fsync() is only needed when switching to dio
- only loop_change_fd() and loop_configure() may switch from buffered
IO to direct IO, so call vfs_fsync() directly here. This way is safe
because either loop is in unbound, or new file isn't attached
- for the other two cases of set_status and set_block_size, direct IO
can only become off, so no need to call vfs_fsync()
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Kun Hu <huk23@m.fudan.edu.cn>
Reported-by: Jiaji Qin <jjtan24@m.fudan.edu.cn>
Closes: https://lore.kernel.org/linux-block/359BC288-B0B1-4815-9F01-3A349B12E816@m.fudan.edu.cn/T/#u
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250318072955.3893805-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
