Add TI INA233 Current and Power Monitor bindings.
Signed-off-by: Leo Yang <leo.yang.sy0@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250116085939.1235598-2-leo.yang.sy0@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Congatec Board Controller. This controller exposes
temperature, voltage, current and fan sensors.
The available sensors list cannot be predicted. Some sensors can be
present or not, depending the system.
The driver has an internal list of all possible sensors, for all Congatec
boards. The Board Controller gives to the driver its sensors list, and
their status (active or not).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20250203-congatec-board-controller-hwmon-v4-1-ff6c76a4662c@bootlin.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge series from "Nícolas F. R. A. Prado" <nfraprado@collabora.com>:
This series enables the MT8188-MT6359 sound driver to retrieve the
MT6359 ACCDET sound component from a mediatek,accdet DT property, which
allows detecting jack insertion/removal.
Patch 1 describes the new property in the binding. Patch 2 implements
the sound component retrieval in the common MTK soundcard driver. Patch
4 updates the MT8188-MT6359 sound driver to register the audio jack and
initialize the ACCDET driver for detection, if the property is present.
Patch 3 adds a stub to prevent a linker failure in case the
MT6359-ACCDET config is disabled.
Tested on the Genio 700 EVK board.
Heiner Kallweit says:
====================
net: phy: clean up PHY package MMD access functions
Move declarations of the functions with users to phylib.h, and remove
unused functions.
====================
Link: https://patch.msgid.link/b624fcb7-b493-461a-a0b5-9ca7e9d767bc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
These functions are used by PHY drivers only, therefore move their
declaration to phylib.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/406c8a20-b62e-4ee3-b174-b566724a0876@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tariq Toukan says:
====================
mlx5: Support HWS flow meter/sampler actions in FS core
This series by Moshe adds support for flow meter and flow sampler HW
Steering actions in FS core level. As these actions can be shared by
multiple rules, these patches use refcounts to manage the HWS actions
sharing in FS core level.
====================
Link: https://patch.msgid.link/1741543663-22123-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for HW Steering action of flow sampler destination. For each
flow sampler created cache the hws action by sampler id as a key. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for HW Steering action of flow meter range. Flow meters
range can use one HWS action for the whole range. Thus, share a cached
HWS action among rules that use same flow meter object range. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Counters HWS actions are shared using refcount, to create action on
demand by flow steering rule and destroy only when no rules are using
the action. The method is extensible to other HWS action types, such as
flow meter and sampler actions, in the downstream patches.
Add an API to facilitate the reuse of get/put logic for HWS actions
shared by refcount.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The fault object was designed exclusively for hwpt's IO page faults (PRI).
But its queue implementation can be reused for other purposes too, such as
hardware IRQ and event injections to user space.
Meanwhile, a fault object holds a list of faults. So it's more accurate to
call it a "fault queue". Combining the reusing idea above, abstract a new
iommufd_eventq as a common structure embedded into struct iommufd_fault,
similar to hwpt_paging holding a common hwpt.
Add a common iommufd_eventq_ops and iommufd_eventq_init to prepare for an
IOMMUFD_OBJ_VEVENTQ (vIOMMU Event Queue).
Link: https://patch.msgid.link/r/e7336a857954209aabb466e0694aab323da95d90.1741719725.git.nicolinc@nvidia.com
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The infrastructure of a fault object will be shared with a new vEVENTQ
object in a following change. Add an iommufd_fault_init helper and an
INIT_EVENTQ_FOPS marco for a vEVENTQ allocator to use too.
Reorder the iommufd_ctx_get and refcount_inc, to keep them symmetrical
with the iommufd_fault_fops_release().
Since the new vEVENTQ doesn't need "response" and its "mutex", so keep
the xa_init_flags and mutex_init in their original locations.
Link: https://patch.msgid.link/r/a9522c521909baeb1bd843950b2490478f3d06e0.1741719725.git.nicolinc@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There is no need to keep them in the header. The vEVENTQ version of these
two functions will turn out to be a different implementation and will not
share with this fault version. Thus, move them out of the header.
Link: https://patch.msgid.link/r/7eebe32f3d354799f5e28128c693c3c284740b21.1741719725.git.nicolinc@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Replace kvm_pmu_vcpu_reset() with the generic PMU reloading mechanism to
ensure the consistency with system registers and to reduce code size.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250315-pmc-v5-5-ecee87dab216@daynix.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Commit d0c94c4979 ("KVM: arm64: Restore PMU configuration on first
run") added the code to reload the PMU configuration on first run.
It is also important to keep the correct state even if system registers
are modified after first run, specifically when debugging Windows on
QEMU with GDB; QEMU tries to write back all visible registers when
resuming the VM execution with GDB, corrupting the PMU state. Windows
always uses the PMU so this can cause adverse effects on that particular
OS.
The usual register writes and reset are already handled independently,
but register writes from userspace are not covered.
Trigger the code to reload the PMU configuration for them instead so
that PMU configuration changes made by users will be applied also after
the first run.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250315-pmc-v5-4-ecee87dab216@daynix.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reload the perf event when setting the vPMU counter (vPMC) registers
(PMCCNTR_EL0 and PMEVCNTR<n>_EL0). This is a change corresponding to
commit 9228b26194 ("KVM: arm64: PMU: Fix GET_ONE_REG
for vPMC regs to return the current value") but for SET_ONE_REG.
Values of vPMC registers are saved in sysreg files on certain occasions.
These saved values don't represent the current values of the vPMC
registers if the perf events for the vPMCs count events after the save.
The current values of those registers are the sum of the sysreg file
value and the current perf event counter value. But, when userspace
writes those registers (using KVM_SET_ONE_REG), KVM only updates the
sysreg file value and leaves the current perf event counter value as is.
It is also important to keep the correct state even if userspace writes
them after first run, specifically when debugging Windows on QEMU with
GDB; QEMU tries to write back all visible registers when resuming the VM
execution with GDB, corrupting the PMU state. Windows always uses the
PMU so this can cause adverse effects on that particular OS.
Fix this by releasing the current perf event and trigger recreating one
with KVM_REQ_RELOAD_PMU.
Fixes: 051ff581ce ("arm64: KVM: Add access handler for event counter register")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250315-pmc-v5-3-ecee87dab216@daynix.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Many functions in pmu-emul.c checks kvm_vcpu_has_pmu(vcpu). A favorable
interpretation is defensive programming, but it also has downsides:
- It is confusing as it implies these functions are called without PMU
although most of them are called only when a PMU is present.
- It makes semantics of functions fuzzy. For example, calling
kvm_pmu_disable_counter_mask() without PMU may result in no-op as
there are no enabled counters, but it's unclear what
kvm_pmu_get_counter_value() returns when there is no PMU.
- It allows callers without checking kvm_vcpu_has_pmu(vcpu), but it is
often wrong to call these functions without PMU.
- It is error-prone to duplicate kvm_vcpu_has_pmu(vcpu) checks into
multiple functions. Many functions are called for system registers,
and the system register infrastructure already employs less
error-prone, comprehensive checks.
Check kvm_vcpu_has_pmu(vcpu) in callers of these functions instead,
and remove the obsolete checks from pmu-emul.c. The only exceptions are
the functions that implement ioctls as they have definitive semantics
even when the PMU is not present.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250315-pmc-v5-2-ecee87dab216@daynix.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Commit a45f41d754 ("KVM: arm64: Add {get,set}_user for
PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}") changed KVM_SET_ONE_REG to update
the mentioned registers in a way matching with the behavior of guest
register writes. This is a breaking change of a UAPI though the new
semantics looks cleaner and VMMs are not prepared for this.
Firecracker, QEMU, and crosvm perform migration by listing registers
with KVM_GET_REG_LIST, getting their values with KVM_GET_ONE_REG and
setting them with KVM_SET_ONE_REG. This algorithm assumes
KVM_SET_ONE_REG restores the values retrieved with KVM_GET_ONE_REG
without any alteration. However, bit operations added by the earlier
commit do not preserve the values retried with KVM_GET_ONE_REG and
potentially break migration.
Remove the bit operations that alter the values retrieved with
KVM_GET_ONE_REG.
Cc: stable@vger.kernel.org
Fixes: a45f41d754 ("KVM: arm64: Add {get,set}_user for PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250315-pmc-v5-1-ecee87dab216@daynix.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Add policy and operational documentation for FWCTL CXL.
Link: https://patch.msgid.link/r/20250307205648.1021626-9-dave.jiang@intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add emulation to support Set Feature mailbox command to cxl_test.
The only feature supported is the device patrol scrub feature. The
set feature allows activation of patrol scrub for the cxl_test
emulated device. The command does not support partial data transfer
even though the spec allows it. This restriction is to reduce complexity
of the emulation given the patrol scrub feature is very minimal.
Link: https://patch.msgid.link/r/20250307205648.1021626-8-dave.jiang@intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add emulation of Get Feature command to cxl_test. The feature for
device patrol scrub is returned by the emulation code. This is
the only feature currently supported by cxl_test. It returns
the information for the device patrol scrub feature.
Link: https://patch.msgid.link/r/20250307205648.1021626-7-dave.jiang@intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add helper function to parse the user data from fwctl RPC ioctl and
send the parsed input parameters to cxl_set_feature() call.
Link: https://patch.msgid.link/r/20250307205648.1021626-6-dave.jiang@intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add helper function to parse the user data from fwctl RPC ioctl and
send the parsed input parameters to cxl_get_feature() call.
Link: https://patch.msgid.link/r/20250307205648.1021626-5-dave.jiang@intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
fwctl provides a fwctl_ops->fw_rpc() callback in order to issue ioctls
to a device. The cxl fwctl driver will start by supporting the CXL
Feature commands: Get Supported Features, Get Feature, and Set Feature.
The fw_rpc() callback provides 'enum fwctl_rpc_scope' parameter where
it indicates the security scope of the call. The Get Supported Features
and Get Feature calls can be executed with the scope of
FWCTL_RPC_CONFIGRATION. The Set Feature call is gated by the effects
of the Feature reported by Get Supported Features call for the specific
Feature.
Only "Get Supported Features" is supported in this patch. Additional
commands will be added in follow on patches. "Get Supported Features"
will filter the Features that are exclusive to the kernel. The flag
field of the Feature details will be cleared of the "Changeable"
field and the "set feat size" will be set to 0 to indicate that
the feature is not changeable.
Link: https://patch.msgid.link/r/20250307205648.1021626-4-dave.jiang@intel.com
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In preparation for cxl fwctl enabling, move data structures related to
cxl feature commands to a user header file.
Reviewed-by; Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://patch.msgid.link/r/20250307205648.1021626-3-dave.jiang@intel.com
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add fwctl support code to allow sending of CXL feature commands from
userspace through as ioctls via FWCTL. Provide initial setup bits. The
CXL PCI probe function will call devm_cxl_setup_fwctl() after the
cxl_memdev has been enumerated in order to setup FWCTL char device under
the cxl_memdev like the existing memdev char device for issuing CXL raw
mailbox commands from userspace via ioctls.
Link: https://patch.msgid.link/r/20250307205648.1021626-2-dave.jiang@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In the case of the following call stack for an atomic file,
FI_DIRTY_INODE is set, but FI_ATOMIC_DIRTIED is not subsequently set.
f2fs_file_write_iter
f2fs_map_blocks
f2fs_reserve_new_blocks
inc_valid_block_count
__mark_inode_dirty(dquot)
f2fs_dirty_inode
If FI_ATOMIC_DIRTIED is not set, atomic file can encounter corruption
due to a mismatch between old file size and new data.
To resolve this issue, I changed to set FI_ATOMIC_DIRTIED when
FI_DIRTY_INODE is set. This ensures that FI_DIRTY_INODE, which was
previously cleared by the Writeback thread during the commit atomic, is
set and i_size is updated.
Cc: <stable@vger.kernel.org>
Fixes: fccaa81de8 ("f2fs: prevent atomic file from being dirtied before commit")
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Sunmin Jeong <s_min.jeong@samsung.com>
Signed-off-by: Yeongjin Gil <youngjin.gil@samsung.com>
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/20250310222339.work.654-kees@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Driver does not support get_txpower mac ops because of which
cfg80211 returns vif->bss_conf.txpower to user space. bss_conf.txpower
gets its value from ieee80211_channel->max_reg_power. However, the final
txpower is dependent on few other parameters apart from max regulatory
supported power. It is the firmware which knows about all these
parameters and considers the minimum for each packet transmission.
All ath12k firmware reports the final TX power in firmware pdev stats
which falls under fw_stats. add get_txpower mac ops to get the TX power
from firmware leveraging fw_stats and return it accordingly.
While at it, there is a possibility that repeated stats request WMI
commands are queued to FW if mac80211/userspace does get tx power back
to back(in Multiple BSS cases). This could potentially consume the WMI
queue completely. Hence limit this by fetching the power only for every
5 seconds and reusing the value until the refresh timeout or when there
is a change in channel.
Also remove init_completion(&ar->fw_stats_complete) in
ath12k_mac_hw_register() as ath12k_fw_stats_init() takes care of
it for each ar.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, for 320 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency of the
primary 160 MHz channel segment and center frequency2 as the center
frequency of the 320 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-3-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, for 160 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency
of the primary 80 MHz channel segment and center frequency2 as
the center frequency of the 160 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-2-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
syzbot warns about a potential deadlock, but this is a false positive
resulting from a missing lockdep annotation: iterate_dir() locks the
parent whereas the inode_lock() it warns about locks the child, which is
guaranteed to be a different lock.
So use inode_lock_nested() instead with the appropriate lock class.
Reported-by: syzbot+019072ad24ab1d948228@syzkaller.appspotmail.com
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Add RPMh stats to read low power statistics for various subsystem
and SoC sleep modes.
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250317-add_qcom_stats-v1-1-016ae05ac4b0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The ASoC soc-utils driver does not require the creation of a platform
device. Originally, this approach was chosen for simplicity when the
driver was first implemented.
With the introduction of the lightweight faux device interface, we now
have a more appropriate alternative. Migrate the driver to utilize the
faux bus, given that the platform device it previously created was not
a real one anyway. This will simplify the code, reducing its footprint
while maintaining functionality.
Cc: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: linux-sound@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://patch.msgid.link/20250317-plat2faux_dev-v1-6-5fe67c085ad5@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add CXL Features support. Setup code for enabling in kernel usage of CXL
Features. Expecting EDAC/RAS to utilize CXL Features in kernel for
things such as memory sparing. Also prepartion for enabling of CXL FWCTL
support to issue allowed Features from user space.
Introduce the 'widgets' property, allowing the creation of widgets from
4 template widgets: Microphone, Line, Headphone, and Speaker. Also
introduce the 'hp-det-gpios' property, which allows using headphone
detection using the specified GPIO.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20250311163255.2664-3-laurentiumihalcea111@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding for imx95's CM7 core, used for audio processing.
Additionally, introduce a common binding for NXP audio processors with
Sound Open Firmware (SOF) support.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://patch.msgid.link/20250311163255.2664-2-laurentiumihalcea111@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The new option is CONFIG_NULL_TTY_DEFAULT_CONSOLE.
if enabled, and CONFIG_VT is disabled, ttynull will become the default
primary console device.
ttynull will be the only console device usually with this option enabled.
Some architectures do call add_preferred_console() which may add another
console though.
Motivation:
Many distributions ship with CONFIG_VT enabled. On tested desktop hardware
if CONFIG_VT is disabled, the default console device falls back to
/dev/ttyS0 instead of /dev/tty.
This could cause issues in user space, and hardware problems:
1. The user space issues include the case where /dev/ttyS0 is
disconnected, and the TCGETS ioctl, which some user space libraries use
as a probe to determine if a file is a tty, is called on /dev/console and
fails. Programs that call isatty() on /dev/console and get an incorrect
false value may skip expected logging to /dev/console.
2. The hardware issues include the case if a user has a science instrument
or other device connected to the /dev/ttyS0 port, and they were to upgrade
to a kernel that is disabling the CONFIG_VT option, kernel logs will then
be sent to the device connected to /dev/ttyS0 unless they edit their
kernel command line manually.
The new CONFIG_NULL_TTY_DEFAULT_CONSOLE option will give users and
distribution maintainers an option to avoid this. Disabling CONFIG_VT and
enabling CONFIG_NULL_TTY_DEFAULT_CONSOLE will ensure the default kernel
console behavior is not dependent on hardware configuration by default, and
avoid unexpected new behavior on devices connected to the /dev/ttyS0 serial
port.
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Adam Simonelli <adamsimonelli@gmail.com>
Link: https://lore.kernel.org/r/20250314160749.3286153-2-adamsimonelli@gmail.com
[pmladek@suse.com: Fixed indentation of the commit message.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Since commit dd348f054b ("jbd2: switch to using the crc32c library"),
jbd2_journal_has_csum_v2or3() and jbd2_journal_has_csum_v2or3_feature()
are the same. Remove jbd2_journal_has_csum_v2or3_feature() and just
keep jbd2_journal_has_csum_v2or3().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://patch.msgid.link/20250207031424.42755-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since commit f2b4fa1964 ("ext4: switch to using the crc32c library"),
ext4_has_metadata_csum() is just an alias for
ext4_has_feature_metadata_csum(). ext4_has_feature_metadata_csum() is
generated by EXT4_FEATURE_RO_COMPAT_FUNCS and uses the regular naming
convention for checking a single ext4 feature. Therefore, remove
ext4_has_metadata_csum() and update all its callers to use
ext4_has_feature_metadata_csum() directly.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://patch.msgid.link/20250207031335.42637-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
If a journal is wiped, we will set journal->j_tail to 0. However if
'write' argument is not set (as it happens for read-only device or for
ocfs2), the on-disk superblock is not updated accordingly and thus
jbd2_journal_recover() cat try to recover the wiped journal. Fix the
check in jbd2_journal_recover() to use journal->j_tail for checking
empty journal instead.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20250206094657.20865-4-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Journal emptiness is not determined by sb->s_sequence == 0 but rather by
sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a
valid transaction ID so the check can spuriously trigger. Remove the
invalid WARN_ON.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20250206094657.20865-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
NSSCC driver is needed to enable the ethernet interfaces present
in RDP433 based on IPQ9574. Since this is not necessary for bootup
enabling it as a module.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250313110359.242491-7-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the nss clock controller found on ipq9574 based devices.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250313110359.242491-6-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
