(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader may add MTD partitions in this subnode if present.
Add an empty partitions node which the bootloader will fill with
configured MTD partitions. Remove #size-cells from MTD node
because this is deprecated.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This matches the real hardware and allows to remove
the virtual 3.3V regulator.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a fixed 3.3V rail supplying several hardware on SOM.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board is very similar to the already upstream
imx8mp-skov-revb-mi1010ait-1cp1.dts with the difference that it uses a
different 7" LVDS panel.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The BD500 replaces the touch display with 3 bicolor LEDs and a push
button on top of a Skov i.MX8-CPU revision C.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C bus recovery can be used to recover when SCL/SDA are stuck low.
To be able to use it, add the necessary GPIO and pinctrl entries.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C2 is exposed on a pin header on the base board, so its pinmux is
always the same if it's enabled.
Therefore, move the definition to the common DTSI, so board DTs only
need to override the status to enable it.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Skov i.MX8MP boards share the same baseboard (modulo revisions)
and are booted with the same bootloader image, which samples some
strapping pins at startup and determines which kernel device tree
to use.
For use as bootloader device tree and as fallback, when no matching
device tree has been found, add a basic variant that doesn't configure
any variant-specific peripherals like displays.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Skov i.MX8MP boards are a family of climate controllers.
In preparation for adding device trees for three more variants,
describe their DT compatible in the bindings.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To reduce heat generation, the Skov i.MX8MP boards should run in nominal
drive mode with a VDD_SOC voltage of 850 mV.
At this operating point, not all frequencies that are achievable with
overdrive mode are possible, so import imx8mp-nominal.dtsi to clock down
the clocks.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The comment in the DT mentions that "currently it is not possible to let
display clocks configure automatically, so we need to set them manually".
Since commit ff06ea04e4 ("clk: imx: clk-imx8mp: Allow media_disp pixel
clock reconfigure parent rate"), this is no longer the case.
Make use of this new functionality by dropping the now unneeded
assigned-clock-rates in &media_blk_ctrl.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mp-nominal.dtsi is meant to be included into boards that want to
override the default overdrive clock settings with settings suitable for
running in nominal drive mode at its lower required voltage.
Specifying fsl,operating-mode = "nominal" informs drivers of this fact,
so they can sanity check runtime clock reconfiguration to observe the
limits imposed by nominal mode.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unlike the i.MX8MM and i.MX8MN SoCs added earlier, the device tree for
the i.MX8MP configures some clocks at frequencies that are only validated
for overdrive mode, i.e. when VDD_SOC is 950 mV.
Boards may want to run their SoC at the lower voltage of 850 mV though
to reduce heat generation and power usage. For this to work, clock rates
need to adhere to the limits of the nominal drive mode.
Add an optional DTSI file which can be included by various boards to run
in this mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initialization code for R-Car S4-8 ES1.2 to improve transfer stability.
Using the new code requires downloading firmware and reading calibration
data from E-FUSE. If either fails, the driver falls back to the old
initialization code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Co-developed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/97d83709495c764b2456d4d25846f5f48197cad0.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After refactoring the code, ufs_renesas_reg_control() is no longer needed,
because all operations are simple and can be called directly. Remove the
ufs_renesas_reg_control() helper function, and call udelay() directly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/69500e4c18be1ca1de360f9e797e282ffef04004.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for returning read register values from
ufs_renesas_reg_control(), so ufs_renesas_set_phy() can use the existing
ufs_renesas_write_phy() helper. Remove the now unused code to save to,
set, and restore from a static array inside ufs_renesas_reg_control().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9fa240a9dc0308d6675138f8434eccb77f051650.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since initialization of the UFS controller on R-Car S4-8 ES1.0 requires
only static values, the driver uses initialization data stored in the const
ufs_param[] array. However, other UFS controller variants (R-Car S4-8
ES1.2) require dynamic values, like those obtained from E-FUSE. Refactor
the initialization code to prepare for this.
This also reduces kernel size by almost 30 KiB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3520e27ac7ff512de6508f630eee3c1689a7c73d.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On R-Car S4-8 ES1.2, the E-FUSE block contains PLL and AFE tuning
parameters for the Universal Flash Storage controller. Document the
related NVMEM properties, and update the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f337169f8183d48b7d94ee13565fea804aade84.1741179611.git.geert+renesas@glider.be
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Task Abort support to handle SCSI command timeouts, ensuring recovery
and cleanup of timed-out commands. This completes the error handling
framework for mpi3mr driver, which already includes device reset, target
reset, bus reset, and host reset.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20250304191453.12994-1-chandrakanth.patil@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A lot of other clocks on the i.MX8MP, including the DRAM set up by the
bootloader are already running at overdrive clock rates. While this is a
deviation from the configuration of other i.MX8M* family SoCs, overdrive
is the default for most i.MX8MP boards and only some special purpose
boards will choose to run the SoC at nominal drive rates. Up the GPU and
NPU clock rates to their overdrive level to be consistent with other
clocks set up in the dtsi.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A device tree binding for the Microchip USB5744 hub controller
was added in commit 02be19e914 ("dt-bindings: usb: Add support
for Microchip usb5744 hub controller").
U-Boot will consume this binding in order to perform the
necessary actions to enable the USB hub ports over I2C.
(We previously used our own out-of-tree driver for
this task)
The Ten64 board does not have any switchable supplies
for the voltage rails utilized by the USB5744, so a
pair of dummy supplies have been added to facilitate
operation with U-Boot's hub driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The log statement reports the packet status code as the hv status code
which causes confusion when debugging as "hv" might refer to a hypervisor,
and sometimes to the host part of the Hyper-V virtualization stack.
Fix the name of the datum being logged to clearly indicate the component
reporting the error. Also log it in hexadecimal everywhere for consistency.
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250304000940.9557-2-romank@linux.microsoft.com
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309145044.38586-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309143348.32896-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Expose per-engine activity via perf pmu (Riana, Lucas, Umesh)
- Add support for EU stall sampling (Harish, Ashutosh)
- Allow userspace to provide low latency hint for submission (Tejas)
- GPU SVM and Xe SVM implementation (Matthew Brost)
Cross-subsystem Changes:
- devres handling for component drivers (Lucas)
- Backmege drm-next to allow cross dependent change with i915
- GPU SVM and Xe SVM implementation (Matthew Brost)
Core Changes:
Driver Changes:
- Fixes to userptr and missing validations (Matthew Auld, Thomas
Hellström, Matthew Brost)
- devcoredump typos and error handling improvement (Shuicheng)
- Allow oa_exponent value of 0 (Umesh)
- Finish moving device probe to devm (Lucas)
- Fix race between submission restart and scheduled being freed (Tejas)
- Fix counter overflows in gt_stats (Francois)
- Refactor and add missing workarounds and tunings for pre-Xe2 platforms
(Aradhya, Tvrtko)
- Fix PXP locks interaction with exec queues being killed (Daniele)
- Eliminate TIMESTAMP_OVERRIDE from xe (Matt Roper)
- Change xe_gen_wa_oob to allow building on MacOS (Daniel Gomez)
- New workarounds for Panther Lake (Tejas)
- Fix VF resume errors (Satyanarayana)
- Fix workaround infra skipping some workarounds dependent on engine
initialization (Tvrtko)
- Improve per-IP descriptors (Gustavo)
- Add more error injections to probe sequence (Francois)
-----BEGIN PGP SIGNATURE-----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=98mS
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-next-2025-03-07' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
UAPI Changes:
- Expose per-engine activity via perf pmu (Riana, Lucas, Umesh)
- Add support for EU stall sampling (Harish, Ashutosh)
- Allow userspace to provide low latency hint for submission (Tejas)
- GPU SVM and Xe SVM implementation (Matthew Brost)
Cross-subsystem Changes:
- devres handling for component drivers (Lucas)
- Backmege drm-next to allow cross dependent change with i915
- GPU SVM and Xe SVM implementation (Matthew Brost)
Core Changes:
Driver Changes:
- Fixes to userptr and missing validations (Matthew Auld, Thomas
Hellström, Matthew Brost)
- devcoredump typos and error handling improvement (Shuicheng)
- Allow oa_exponent value of 0 (Umesh)
- Finish moving device probe to devm (Lucas)
- Fix race between submission restart and scheduled being freed (Tejas)
- Fix counter overflows in gt_stats (Francois)
- Refactor and add missing workarounds and tunings for pre-Xe2 platforms
(Aradhya, Tvrtko)
- Fix PXP locks interaction with exec queues being killed (Daniele)
- Eliminate TIMESTAMP_OVERRIDE from xe (Matt Roper)
- Change xe_gen_wa_oob to allow building on MacOS (Daniel Gomez)
- New workarounds for Panther Lake (Tejas)
- Fix VF resume errors (Satyanarayana)
- Fix workaround infra skipping some workarounds dependent on engine
initialization (Tvrtko)
- Improve per-IP descriptors (Gustavo)
- Add more error injections to probe sequence (Francois)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ilc5jvtyaoyi6woyhght5a6sw5jcluiojjueorcyxbynrcpcjp@mw2mi6rd6a7l
The original support for incrementally consumed buffers didn't allow it
to be used with bundles, with the assumption being that incremental
buffers are generally larger, and hence there's less of a nedd to
support it.
But that assumption may not be correct - it's perfectly viable to use
smaller buffers with incremental consumption, and there may be valid
reasons for an application or framework to do so.
As there's really no need to explicitly disable bundles with
incrementally consumed buffers, allow it. This actually makes the peek
side cheaper and simpler, with the completion side basically the same,
just needing to iterate for the consumed length.
Reported-by: Norman Maurer <norman_maurer@apple.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 2a51c327d4.
The kernel registered bvecs do use the iov_iter_advance() API, so we
can't rely on this simplification anymore.
Fixes: 27cb27b6d5 ("io_uring: add support for kernel registered bvecs")
Reported-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Link: https://lore.kernel.org/r/20250310184825.569371-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add UBLK_TEST_QUIET, so we can print test result(PASS/SKIP/FAIL) only.
Also always run from test script's current directory, then the same test
script can be started from other work directory.
This way helps a lot to reuse this test source code and scripts for
other projects(liburing, blktests, ...)
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-12-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add stress_test_01 for running IO vs. killing ublk server, so io_uring exit &
cancel code path can be covered, same with ublk's cancel code path.
Especially IO buffer lifetime is one big thing for ublk zero copy, the added
test can verify if this area works as expected.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-11-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add stress_test_01 for running IO vs. removing device for verifying that
ublk device removal can work as expected when heavy IO workloads are in
progress.
null, loop and loop/zc are covered in this tests.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-10-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Load ublk_drv module in _prep_test(), and unload it in _cleanup_test(),
so that test can always be done in consistent state.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-9-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move zero copy feature check into _add_ublk_dev() since we will have
more tests which requires to cover zero copy.
Then one check function of _check_add_dev() has to be added for dealing
with cleanup since '_add_ublk_dev()' is run in sub-shell, and we can't
exit from it to terminal shell.
Meantime always return error code from _add_ublk_dev().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-8-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
More devices can be created in single tests, so simply remove all
ublk devices in _cleanup_test(), meantime remove the ${dev_id} argument
of _cleanup_test().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-7-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The argument of '-a' doesn't follow any value, so fix it by putting it
with '-z' together.
Fixes: bedc9cbc5f ("selftests: ublk: add ublk zero copy test")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20250303124324.3563605-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the Documentation to be more precise.
v2: Update for clarity
v3: Further details in Todo
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Anusha Srivatsa <asrivats@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/640856/?series=144073&rev=5
Fedora introduced a "MiniDebuginfo" feature, in which an LZMA-compressed
ELF file is placed inside a section named ".gnu_debugdata". This file
contains nothing but a symbol table, which can be used to supplement the
.dynsym section which only contains required symbols for runtime.
It is supported by GDB for stack traces, but it should be useful for
tracing as well. Implement support for loading symbols from
.gnu_debugdata.
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: https://lore.kernel.org/r/20250307232206.2102440-4-stephen.s.brennan@oracle.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Internally lzma_decompress_to_file() creates a FILE from the filename.
Add an API that takes an existing FILE directly. This allows
decompressing already-open files and even buffers opened by fmemopen().
It is necessary for supporting .gnu_debugdata in the next patch.
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: https://lore.kernel.org/r/20250307232206.2102440-3-stephen.s.brennan@oracle.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
This allows us to use them without needing to ifdef the calling code.
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: https://lore.kernel.org/r/20250307232206.2102440-2-stephen.s.brennan@oracle.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
When preparing the mem events for the argv copies are intentionally
made. These copies are leaked and cause runs of perf using address
sanitizer to fail. Rather than leak the memory allocate a chunk of
memory for the mem event names upfront and build the strings in this -
the storage is sized larger than the previous buffer size. The caller
is then responsible for clearing up this memory. As part of this
change, remove the mem_loads_name and mem_stores_name global buffers
then change the perf_pmu__mem_events_name to write to an out argument
buffer.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Thomas Falcon <thomas.falcon@intel.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Link: https://lore.kernel.org/r/20250308012853.1384762-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The SiFive Performance P650 core (including the vector-enabled P670 and
area-optimized P450/P470 variants) updates the P550 microarchitecture.
It brings in the debug, trace, and counter events from newer Bullet
cores, and adds new events for iTLB and dTLB multi-hits.
All other PMU events are unchanged from the P550 core.
Signed-off-by: Eric Lin <eric.lin@sifive.com>
Co-developed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Tested-by: Ian Rogers <irogers@google.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20250213220341.3215660-8-samuel.holland@sifive.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The SiFive Performance P550 core features an out-of-order
microarchitecture which exposes the same PMU events as Bullet,
plus events for UTLB hits and PTE cache misses/hits.
Add support for specifying these events using symbolic names.
Signed-off-by: Eric Lin <eric.lin@sifive.com>
Co-developed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Tested-by: Ian Rogers <irogers@google.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20250213220341.3215660-7-samuel.holland@sifive.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
SiFive Bullet microarchitecture cores with mimpid values starting with
0x0d or greater add new PMU events to count TLB miss stall cycles.
All other PMU events are unchanged from earlier Bullet cores.
Signed-off-by: Eric Lin <eric.lin@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Tested-by: Ian Rogers <irogers@google.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20250213220341.3215660-6-samuel.holland@sifive.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
