On Mobileye EyeQ5, the bootloader will put MAC addresses into memory.
Declare that as reserved memory to be used by the kernel, exposing
nvmem cells. That region has a 12-byte header and a 4-byte trailing CRC.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20241230143035.265518-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Also adapt the dynamic sysfs cell logic to handle the const attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20241230143035.265518-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 3ab1663af6 ("watchdog: stm32_iwdg: Add pretimeout support")
introduces the support for the pre-timeout interrupt.
The support for this interrupt is optional but the driver uses the
platform_get_irq() which produces an error message during the driver
probe if we don't have any `interrupts` property in the DT.
Use the platform_get_irq_optional() API to get rid of the error message
as this property is optional.
Fixes: 3ab1663af6 ("watchdog: stm32_iwdg: Add pretimeout support")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241218092227.771133-1-clement.legoffic@foss.st.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix dp mode valid issue to avoid abnormal display of limit state.
After DP passes link training, it can express the lane count of the
current link status is good. Calculate the maximum bandwidth supported
by DP using the current lane count.
The color format will select the best one based on the bandwidth
requirements of the current timing mode. If the current timing mode
uses RGB and meets the DP link bandwidth requirements, RGB will be used.
If the timing mode uses RGB but does not meet the DP link bandwidthi
requirements, it will continue to check whether YUV422 meets
the DP link bandwidth.
FEC overhead is approximately 2.4% from DP 1.4a spec 2.2.1.4.2.
The down-spread amplitude shall either be disabled (0.0%) or up
to 0.5% from 1.4a 3.5.2.6. Add up to approximately 3% total overhead.
Because rate is already divided by 10,
mode->clock does not need to be multiplied by 10.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Liankun Yang <liankun.yang@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241025083036.8829-3-liankun.yang@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Setting up misc0 for Pixel Encoding Format.
According to the definition of YCbCr in spec 1.2a Table 2-96,
0x1 << 1 should be written to the register.
Use switch case to distinguish RGB, YCbCr422,
and unsupported color formats.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Liankun Yang <liankun.yang@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241025083036.8829-2-liankun.yang@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
We introduced a couple of helpers for copying iomem over iov_iter, and
the functions were formed like the former copy_from/to_user(), and the
return value was adjusted to 0/-EFAULT, which made the code transition
a bit easier at that time.
OTOH, the standard copy_from/to_iter() functions have different
argument orders and the return value, and this difference can be
confusing. It's not only confusing but dangerous; actually I did
write a wrong code due to that once :-<
For reducing the confusion, this patch changes the syntax of those
helpers to align with the standard copy_from/to_iter(). The argument
order is changed and the return value is the size of copied bytes.
The callers of those functions are updated accordingly, too.
Link: https://patch.msgid.link/20241230114903.4959-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit c2d188e137.
Although it's fine to filter the invalid UMP groups at the first probe
time, this will become a problem when UMP groups are updated and
(re-)activated. Then there is no way to re-add the substreams
properly for the legacy rawmidi, and the new active groups will be
still invisible.
So let's revert the change. This will move back to showing the full
16 groups, but it's better than forever lost.
Link: https://patch.msgid.link/20241230114023.3787-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OSS sequencer handles the SysEx messages split in 6 bytes packets, and
ALSA sequencer OSS layer tries to combine those. It stores the data
in the internal buffer and this access is racy as of now, which may
lead to the out-of-bounds access.
As a temporary band-aid fix, introduce a mutex for serializing the
process of the SysEx message packets.
Reported-by: Kun Hu <huk23@m.fudan.edu.cn>
Closes: https://lore.kernel.org/2B7E93E4-B13A-4AE4-8E87-306A8EE9BBB7@m.fudan.edu.cn
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241230110543.32454-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
3d3f43fab4 ("ALSA: compress_offload: improve file descriptors
installation for dma-buf") fixed some of descriptor races in
snd_compr_task_new(), but there's a couple more left.
We need to grab the references to dmabuf before moving them into
descriptor table - trying to do that by descriptor afterwards might
end up getting a different object, with a dangling reference left in
task->{input,output}
Fixes: 3d3f43fab4 ("ALSA: compress_offload: improve file descriptors installation for dma-buf")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Link: https://patch.msgid.link/20241229185232.GA1977892@ZenIV
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only board that actually requires these properties is
meson8b-odroidc1.dts but that already sets it on it's own. Drop these
properties from meson.dtsi because otherwise they can cause dtc
warnings:
/soc/usb@c9040000: unnecessary #address-cells/#size-cells without
"ranges", "dma-ranges" or child "reg" property
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241226220352.965505-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Extended the `mi_enum_attr()` function interface with an additional
parameter, `struct ntfs_inode *ni`, to allow marking the inode
as bad as soon as an error is detected.
Reported-by: syzbot+73d8fc29ec7cba8286fa@syzkaller.appspotmail.com
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
The WDOG_B is connected to external PMIC, so set "fsl,ext-reset-output"
to enable triggering PMIC reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WDOG_B is connected to external PMIC, so set "fsl,ext-reset-output"
to enable triggering PMIC reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WDOG_B is connected to external PMIC, so set "fsl,ext-reset-output"
to enable triggering PMIC reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, kvm doesn't delegate the few traps such as misaligned
load/store, illegal instruction and load/store access faults because it
is not expected to occur in the guest very frequently. Thus, kvm gets a
chance to act upon it or collect statistics about it before redirecting
the traps to the guest.
Collect both guest and host visible statistics during the traps.
Enable them so that both guest and host can collect the stats about
them if required.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241224-kvm_guest_stat-v2-3-08a77ac36b02@rivosinc.com
Signed-off-by: Anup Patel <anup@brainfault.org>
SBI PMU specification defines few firmware counters which can be
used by the guests to collect the statstics about various traps
occurred in the host.
Update these counters whenever a corresponding trap is taken
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241224-kvm_guest_stat-v2-2-08a77ac36b02@rivosinc.com
Signed-off-by: Anup Patel <anup@brainfault.org>
The M-mode redirects an unhandled instruction access
fault trap back to S-mode when not delegating it to
VS-mode(hedeleg). However, KVM running in HS-mode
terminates the VS-mode software when back from M-mode.
The KVM should redirect the trap back to VS-mode, and
let VS-mode trap handler decide the next step.
Signed-off-by: Quan Zhou <zhouquan@iscas.ac.cn>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241224-kvm_guest_stat-v2-1-08a77ac36b02@rivosinc.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Implement a KVM SBI SUSP extension handler. The handler only
validates the system suspend entry criteria and prepares for resuming
in the appropriate state at the resume_addr (as specified by the SBI
spec), but then it forwards the call to the VMM where any system
suspend behavior may be implemented. Since VMM support is needed, KVM
disables the extension by default.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20241017074538.18867-5-ajones@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Add ENETC 0 (1G ethernet port) support for i.MX95-19x19-EVK board. In
addition, because all ENETC instances share MDIO bus, so enable EMDIO
at the same time.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add NETC related nodes for i.MX95.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mdio-gpio is not a valid pattern according to mdio-gpio.yaml.
Use the generic 'mdio' name to fix the following dt-schema warnings:
'mdio-gpio' does not match '^mdio(-(bus|external))?(@.+|-([0-9]+))?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently there are 3 type of boards (imx6q|imx6qp|imx6dl-sabresd)
based on imx6qdl-sabresd.dtsi, they all do not set the dr_mode for
usbotg device node. The chipidea usb driver will configure it to otg
mode by default if the dr_mode is not set, but some testcases need to
parse the dr_mode from DT and decide the follow-up test strategy, here
set the dr_mode to otg explicitly for these 3 imx6qdl-sabresd based
boards.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mm-phg board has an AUO G084SN05 V9 8.4" 800x600 LVDS panel.
Improve the devicetree description by passing the LVDS compatible
string to fix the following dt-schema warning:
imx8mm-phg.dtb: panel: compatible:0: 'panel-lvds' is not one of
['admatec,9904379', 'auo,b101ew05', 'auo,g084sn05',
'chunghwa,claa070wp03xg','edt,etml0700z9ndha', 'hannstar,hsd101pww2',
'hydis,hv070wx2-1e0', 'jenson,bl-jt60050-01a', 'tbs,a711-panel']
...
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support pca9452 on imx93-14x14-evk.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a simple-framebuffer node for U-Boot to further fill and activate.
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board has a pull-up resistor for MDIO pin per PHY design guide.
When MDIO is idle, it needs to be high and open drain is better
to be used here for power saving.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board has a pull-up resistor for MDIO pin per PHY design guide.
When MDIO is idle, it needs to be high and open drain is better
to be used here for power saving.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to adv7180.yaml, the correct property name is
"adi,force-bt656-4".
Update it accordingly to fix several dt-schema warnings:
adv7280@21: 'adv,force-bt656-4' does not match any of the regexes: ...
imx6qdl-apalis.dtsi is the only in-tree kernel user of this property.
BSD does have a adv7180 driver, so should not be impacted.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The regulator handling was introduced by commit `966d731520 (usb: phy:
mxs: enable regulator phy-3p0 to improve signal qualilty, 2024-07-26)`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d731520 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d731520 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only check EC for MKBP events when the ACPI notify value indicates the
notify is due to an MKBP host event. This reduces unnecessary queries to
the EC.
Notify value 0x80 is reserved for devices specific notifies. It is used
by many devices to indicate various events. It's only used by cros_ec
for MKBP events.
Signed-off-by: Rob Barnes <robbarnes@google.com>
Link: https://lore.kernel.org/r/20241218015759.3558830-1-robbarnes@google.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241215-sysfs-const-bin_attr-chrome-v1-1-92249c4bc295@weissschuh.net
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
After applying 4c03a44e26 ("arm64: dts: mediatek: mt8195-cherry: Remove
keyboard-backlight node"), there are no users for using the OF match.
Instead, the device is added via drivers/mfd/cros_ec_dev.c by
970c3a6b7a ("mfd: cros_ec: Register keyboard backlight subdevice").
Remove the DT bindings.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20241206031405.1711996-3-tzungbi@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
After applying 4c03a44e26 ("arm64: dts: mediatek: mt8195-cherry: Remove
keyboard-backlight node"), there are no users for using the OF match.
Instead, the device is added via drivers/mfd/cros_ec_dev.c by
970c3a6b7a ("mfd: cros_ec: Register keyboard backlight subdevice").
Remove the OF match.
Link: https://lore.kernel.org/r/20241206031405.1711996-2-tzungbi@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Remove the retry of the get protocol info command. It is not needed
anymore, because RWSIG continue command is send before start of the
probing. That assures the EC device is ready in RW and there is no
need to try again because FPMCU is not fully booted.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Link: https://lore.kernel.org/r/20241206091514.2538350-3-dawidn@google.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
There are EC devices, like FPMCU, that use RWSIG as a method of
authenticating RW section. After the authentication succeeds, EC device
waits some time before jumping to RW. EC can be probed before the jump,
which means there is a time window after jump to RW in which EC won't
respond, because it is not initialized. It can cause a communication
errors after probing.
To avoid such problems, send the RWSIG continue command first, which
skips waiting for the jump to RW. Send the command more times, to make
sure EC is ready in RW before the start of the actual probing process. If
a EC device doesn't support the RWSIG, it will respond with invalid
command error code and probing will continue as usual.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Link: https://lore.kernel.org/r/20241206091514.2538350-2-dawidn@google.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
