The complete handler will at least be called after 16 requests have
completed, but will still handle all finisher requests. Since we have
to maintain a costant filling in the isoc queue we ensure this by
adding zero length requests.
By counting the amount enqueued requests we can ensure that the queue is
never underrun and only need to get active if the queue is running
critical. This patch is setting 32 as the critical level, which
is twice the request amount that is needed to create interrupts.
To properly solve the amount of zero length requests that needs to
be held in the hardware after one interrupt needs to be measured
and depends on the runtime of the first enqueue run after the interrupt
triggered. For now we just use twice the amount of requests between an
interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-2-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the req_free list will updated if enqueuing one request was not
possible it will be added back to the free list. With every available
free request in the queue it is a valid case for the pump worker to use
it and continue the pending bufferdata into requests for the req_ready
list.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-1-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI does not share the contents of the Enter_USB Message
that was used, so the active mode still has to be always
determined from the enumerated USB device. However, after
UCSI v2.0 it is possible to check separately is USB4 the
active mode.
So with USB2 and USB3 the mode is always determined from the
result of the USB enumeration, and when USB4 USB Mode is
active, UCSI driver can assign the mode directly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB capabilities can be extracted from the response to
the Get Connector Capability command. USB2 and USB3 support
can be checked from the Operation Mode field, and USB4
support from the Extended Operation Mode field.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8450-HDK
Link: https://lore.kernel.org/r/20241016131834.898599-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file shows the supported USB modes (USB 2.0,
USB 3.0 and USB4) of the partner, and the currently active
mode.
The active mode is determined primarily by checking the
speed of the enumerated USB device. When USB Power Delivery
is supported, the active USB mode should be always the mode
that was used with the Enter_USB Message, regardless of the
result of the USB enumeration. The port drivers can
separately assign the mode with a dedicated API.
If USB Power Delivery Identity is supplied for the partner
device, the supported modes are extracted from it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file, named "usb_capability", will show the
supported USB modes, which are USB 2.0, USB 3.2 and USB4.
These modes are defined in the USB Type-C (R2.0) and USB
Power Delivery (R3.0 V2.0) Specifications.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the compatible for the Rockchip RK3576 variant.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241016083224.14839-1-frawang.cn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_mmap() creates VMAs which can only be used through
usbdev_do_ioctl(), which requires FMODE_WRITE; so usbdev_mmap() is only
useful with FMODE_WRITE.
On typical Linux systems, files at /dev/bus/usb/*/* are mode 0664, so
UIDs without any special privileges can't use usbdev_do_ioctl(), but
they can still execute the usbdev_mmap() codepath.
Check for FMODE_WRITE in usbdev_mmap() to reduce attack surface a little
bit.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241016-usbdev-mmap-require-write-v1-1-6f8256414d5c@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 160c826b4d ("selftest: hid: add missing run-hid-tools-tests.sh")
has added the run-hid-tools-tests.sh script for it to be installed, but
I forgot to add the tests directory together.
If running the test case without the tests directory, will results in
the following error message:
make -C tools/testing/selftests/ TARGETS=hid install \
INSTALL_PATH=$KSFT_INSTALL_PATH
cd $KSFT_INSTALL_PATH
./run_kselftest.sh -t hid:hid-core.sh
/usr/lib/python3.11/site-packages/_pytest/config/__init__.py:331: PluggyTeardownRaisedWarning: A plugin raised an exception during an old-style hookwrapper teardown.
Plugin: helpconfig, Hook: pytest_cmdline_parse
UsageError: usage: __main__.py [options] [file_or_dir] [file_or_dir] [...]
__main__.py: error: unrecognized arguments: --udevd
inifile: None
rootdir: /root/linux/kselftest_install/hid
In fact, the run-hid-tools-tests.sh script uses the scripts in the tests
directory to run tests. The tests directory also needs to be added to be
installed.
Fixes: ffb85d5c9e ("selftests: hid: import hid-tools hid-core tests")
Cc: stable@vger.kernel.org
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The battery capacity calibration function continues to be a source of
bugs for end users, especially when coming out of suspend. This occurs
when the device has incorrect readings for voltage, and causes the
current code to set fully charged capacity incorrectly.
Add checks to ensure we don't attempt a capacity calibration when we
have invalid voltage values or no battery present, and remove the code
that attempts to automatically set the fully charged capacity in lieu of
making the value writeable. This way userspace is able to adjust the
fully charged capacity for a degraded battery.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240926144346.94630-3-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver has a thread that checks the battery every 8 seconds. Stop
this thread during device suspend as while the device is suspended not
all values seem to be read correctly (such as battery voltage). The
resume function triggers the thread to start again.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240926144346.94630-2-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use IC status regfield to rewrite the 'get_staus' function. The original
one cannot cover some special scenario like as charger OTG or JEITA case.
Fixes: 4a1a5f6781 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reported-by: Lucas Tsai <lucas_tsai@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/67ba92bb4a9c51d9cafadab30b788a3a2c3048e1.1727252762.git.cy_huang@richtek.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Enabling dtc interrupt_provider check reveals the example is missing
the "interrupt-controller" property as it is a dependency of
"#interrupt-cells". However, the PMIC parent node is not an interrupt
controller at all, so the "#interrupt-cells" is erroneous.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240926213727.3064977-1-robh@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The attribute arrays are only modified during the __init phase.
To protect them against intentional or accidental modification,
mark them as __ro_after_init.
To make sure no modifications are introduced, also mark the return
values of the accessors as const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241005-power-supply-cleanups-v1-3-45303b2d0a4d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since commit ("power: supply: Drop use_cnt check from power_supply_property_is_writeable()"),
this function does not check use_cnt anymore, making it unsuitable for
general usage. As it is only used by the psy core anyways, remove it
from the public header and unexport it to avoid misusage.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241005-power-supply-cleanups-v1-2-45303b2d0a4d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Correct bq27426 registers, according to technical reference manual
it does not have Design Capacity register so it is not register
compatible with bq27421.
Fixes: 5ef6a16033 ("power: supply: bq27xxx: Add support for BQ27426")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20241016-fix_bq27426-v2-1-aa6c0f51a9f6@mainlining.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Zijian Zhang says:
====================
Function msg_verify_data should have context of bytes_cnt and k instead of
assuming they are zero. Otherwise, test_sockmap with data integrity test
will report some errors. I also fix the logic related to size and index j
1/ 6 sockmap::txmsg test passthrough:FAIL
2/ 6 sockmap::txmsg test redirect:FAIL
7/12 sockmap::txmsg test apply:FAIL
10/11 sockmap::txmsg test push_data:FAIL
11/17 sockmap::txmsg test pull-data:FAIL
12/ 9 sockmap::txmsg test pop-data:FAIL
13/ 1 sockmap::txmsg test push/pop data:FAIL
...
Pass: 24 Fail: 52
After fixing msg_verify_data, some of the errors are solved, but for push
pull and pop, we may need more fixes to msg_verify_data, added a TODO
10/11 sockmap::txmsg test push_data:FAIL
11/17 sockmap::txmsg test pull-data:FAIL
12/ 9 sockmap::txmsg test pop-data:FAIL
...
Pass: 37 Fail: 15
Besides, added a custom errno EDATAINTEGRITY for msg_verify_data, we
shall not ignore the error in txmsg_cork case, and fixed the txmsg_redir
in test_txmsg_pull "Test pull + redirect" case.
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
txmsg_redir in "Test pull + redirect" case of test_txmsg_pull should be
1 instead of 0.
Fixes: 328aa08a08 ("bpf: Selftests, break down test_sockmap into subtests")
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Link: https://lore.kernel.org/r/20241012203731.1248619-3-zijianzhang@bytedance.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Function msg_verify_data should have context of bytes_cnt and k instead of
assuming they are zero. Otherwise, test_sockmap with data integrity test
will report some errors. I also fix the logic related to size and index j
1/ 6 sockmap::txmsg test passthrough:FAIL
2/ 6 sockmap::txmsg test redirect:FAIL
7/12 sockmap::txmsg test apply:FAIL
10/11 sockmap::txmsg test push_data:FAIL
11/17 sockmap::txmsg test pull-data:FAIL
12/ 9 sockmap::txmsg test pop-data:FAIL
13/ 1 sockmap::txmsg test push/pop data:FAIL
...
Pass: 24 Fail: 52
After applying this patch, some of the errors are solved, but for push,
pull and pop, we may need more fixes to msg_verify_data, added a TODO
10/11 sockmap::txmsg test push_data:FAIL
11/17 sockmap::txmsg test pull-data:FAIL
12/ 9 sockmap::txmsg test pop-data:FAIL
...
Pass: 37 Fail: 15
Besides, added a custom errno EDATAINTEGRITY for msg_verify_data, we
shall not ignore the error in txmsg_cork case.
Fixes: 753fb2ee09 ("bpf: sockmap, add msg_peek tests to test_sockmap")
Fixes: 16edddfe3c ("selftests/bpf: test_sockmap, check test failure")
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Link: https://lore.kernel.org/r/20241012203731.1248619-2-zijianzhang@bytedance.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Several miscellaneous fixes:
- Many bnxt_re bug fixes - Memory leaks, kasn, NULL pointer deref, soft
lockups, error unwinding and some small functional issues
- Error unwind bug in rdma netlink
- Two issues with incorrect VLAN detection for iWarp
- skb_splice_from_iter() splat in siw
- Give SRP slab caches unique names to resolve the merge window WARN_ON
regression
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZw/9ZAAKCRCFwuHvBreF
Yez7AQCAcC4NB1HYMnYiFIn9GPtxVaqTt+VOIK9h/5mIMGDGMAD8DX+3sOqBLlDX
ZLi/2Se8gej+yoWRqSskrc2Pv2Mfoww=
=ryK4
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Several miscellaneous fixes. A lot of bnxt_re activity, there will be
more rc patches there coming.
- Many bnxt_re bug fixes - Memory leaks, kasn, NULL pointer deref,
soft lockups, error unwinding and some small functional issues
- Error unwind bug in rdma netlink
- Two issues with incorrect VLAN detection for iWarp
- skb_splice_from_iter() splat in siw
- Give SRP slab caches unique names to resolve the merge window
WARN_ON regression"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/bnxt_re: Fix the GID table length
RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages
RDMA/bnxt_re: Change the sequence of updating the CQ toggle value
RDMA/bnxt_re: Fix an error path in bnxt_re_add_device
RDMA/bnxt_re: Avoid CPU lockups due fifo occupancy check loop
RDMA/bnxt_re: Fix a possible NULL pointer dereference
RDMA/bnxt_re: Return more meaningful error
RDMA/bnxt_re: Fix incorrect dereference of srq in async event
RDMA/bnxt_re: Fix out of bound check
RDMA/bnxt_re: Fix the max CQ WQEs for older adapters
RDMA/srpt: Make slab cache names unique
RDMA/irdma: Fix misspelling of "accept*"
RDMA/cxgb4: Fix RDMA_CM_EVENT_UNREACHABLE error for iWARP
RDMA/siw: Add sendpage_ok() check to disable MSG_SPLICE_PAGES
RDMA/core: Fix ENODEV error for iWARP test over vlan
RDMA/nldev: Fix NULL pointer dereferences issue in rdma_nl_notify_event
RDMA/bnxt_re: Fix the max WQEs used in Static WQE mode
RDMA/bnxt_re: Add a check for memory allocation
RDMA/bnxt_re: Fix incorrect AVID type in WQE structure
RDMA/bnxt_re: Fix a possible memory leak
Leverage the existed function perf_pmu__name_from_config() to check if
an event is topdown metrics event. perf_pmu__name_from_config() goes
through the defined formats and figures out the config of pre-defined
topdown events.
This avoids to figure out the config of topdown pre-defined events with
hard-coded format strings "event=" and "umask=" and provides more
flexibility.
Suggested-by: Ian Rogers <irogers@google.com>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20241011110207.1032235-2-dapeng1.mi@linux.intel.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The commit "3b5edc0421 (perf x86/topdown: Don't move topdown metric
events in group)" modifies topdown metrics comparator to move topdown
metrics events which are not in same group with previous event. But it
just modifies the 2nd comparator and causes the comparators become
asymmetric.
Thus modify the 1st topdown metrics comparator and make the two
comparators be symmetric, and refine the comments as well.
Suggested-by: Ian Rogers <irogers@google.com>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20241011110207.1032235-1-dapeng1.mi@linux.intel.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=tFDD
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.12-2024-10-16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge an amd-pstate driver fix for 6.12-rc4 from Mario Limonciello:
"Fix a regression introduced where boost control malfunctioned in
amd-pstate"
* tag 'amd-pstate-v6.12-2024-10-16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled
Resize the GICR register region as it currently seeps into the CPU Control
Processor mailbox RX region.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20240612124056.39230-4-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
For historical reasons syscon-reboot has used an 'offset' property. As a
child on a MMIO bus having a 'reg' property is more appropriate. Accept
'reg' as an alternative to 'offset'.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241015225948.3971924-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The syscon-reboot binding used 'offset' for historical reasons. Having a
reg property is appropriate when these nodes are children of a MMIO bus.
Add a reg property and modify the constraints so that one of 'reg' or
'offset' is expected.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241015225948.3971924-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the description and compatible for PCIe 6a, as it is in fact a
4-lanes controller and PHY, but it can also be used in 2-lanes mode. For
4-lanes mode, it uses the lanes provided by PCIe 6b. For 2-lanes mode,
PCIe 6a uses 2 lanes and then PCIe 6b uses the other 2 lanes. The number
of lanes in which the PHY should be configured depends on a TCSR register
value on each individual board.
Cc: stable+noautosel@kernel.org # Depends on pcie-qcom 16.0 GT/s support
Fixes: 5eb83fc102 ("arm64: dts: qcom: x1e80100: Add PCIe nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009-x1e80100-dts-fixes-pcie6a-v3-1-14a1163e691b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a driver for the charger in the TWL6030/32. For now it does not report
much in sysfs but parameters are set up for USB, charging is enabled with
the specified parameters. It stops charging when full and also restarts
charging.
This prevents ending up in a system setup where you run out of battery
although a charger is plugged in after precharge completed.
Battery voltage behavior was checked via the GPADC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241016080314.222674-3-andreas@kemnade.info
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use a fallback compatible since for especially for generic
defensive setup of parameters, both 6030 and 6032 are the same and
U-Boot actually uses a generic 6030/32 function to enable the
charger.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241016080314.222674-2-andreas@kemnade.info
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The pipediv2_clk's source from the same mux as pipe clock. So they have
same limitation, which is that the PHY sequence requires to enable these
local CBCs before the PHY is actually outputting a clock to them. This
means the clock won't actually turn on when we vote them. Hence, let's
skip the halt bit check of the pipediv2_clk, otherwise pipediv2_clk may
stuck at off state during bootup.
Cc: stable@vger.kernel.org
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Suggested-by: Mike Tipton <quic_mdtipton@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241011104142.1181773-6-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:
kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout
According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:
'When an interrupt transfer involves more data than can fit in one
data payload of the currently established maximum size, all data
payloads are required to be maximum-sized except for the last data
payload, which will contain the remaining data. An interrupt transfer
is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data expected
• Transfers a packet with a payload size less than wMaxPacketSize or
transfers a zero-length packet'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365
Fixes: 7b05933340 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There's issue as follows:
KASAN: maybe wild-memory-access in range [0xdead...108-0xdead...10f]
CPU: 3 UID: 0 PID: 2805 Comm: rmmod Tainted: G W
RIP: 0010:proto_unregister+0xee/0x400
Call Trace:
<TASK>
__do_sys_delete_module+0x318/0x580
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
As bnep_init() ignore bnep_sock_init()'s return value, and bnep_sock_init()
will cleanup all resource. Then when remove bnep module will call
bnep_sock_cleanup() to cleanup sock's resource.
To solve above issue just return bnep_sock_init()'s return value in
bnep_exit().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This partially reverts 81b3e33bb054 ("Bluetooth: btusb: Don't fail
external suspend requests") as it introduced a call to hci_suspend_dev
that assumes the system-suspend which doesn't work well when just the
device is being suspended because wakeup flag is only set for remote
devices that can wakeup the system.
Reported-by: Rafael J. Wysocki <rafael@kernel.org>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Kenneth Crudup <kenny@panix.com>
Fixes: 610712298b ("Bluetooth: btusb: Don't fail external suspend requests")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Rafael J. Wysocki <rafael@kernel.org>
If iso_init() has been called, iso_exit() must be called on module
unload. Without that, the struct proto that iso_init() registered with
proto_register() becomes invalid, which could cause unpredictable
problems later. In my case, with CONFIG_LIST_HARDENED and
CONFIG_BUG_ON_DATA_CORRUPTION enabled, loading the module again usually
triggers this BUG():
list_add corruption. next->prev should be prev (ffffffffb5355fd0),
but was 0000000000000068. (next=ffffffffc0a010d0).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:29!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 4159 Comm: modprobe Not tainted 6.10.11-4+bt2-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x61/0xa0
...
__list_add_valid_or_report+0x61/0xa0
proto_register+0x299/0x320
hci_sock_init+0x16/0xc0 [bluetooth]
bt_init+0x68/0xd0 [bluetooth]
__pfx_bt_init+0x10/0x10 [bluetooth]
do_one_initcall+0x80/0x2f0
do_init_module+0x8b/0x230
__do_sys_init_module+0x15f/0x190
do_syscall_64+0x68/0x110
...
Cc: stable@vger.kernel.org
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If bt_debugfs is not created successfully, which happens if either
CONFIG_DEBUG_FS or CONFIG_DEBUG_FS_ALLOW_ALL is unset, then iso_init()
returns early and does not set iso_inited to true. This means that a
subsequent call to iso_init() will result in duplicate calls to
proto_register(), bt_sock_register(), etc.
With CONFIG_LIST_HARDENED and CONFIG_BUG_ON_DATA_CORRUPTION enabled, the
duplicate call to proto_register() triggers this BUG():
list_add double add: new=ffffffffc0b280d0, prev=ffffffffbab56250,
next=ffffffffc0b280d0.
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:35!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 2 PID: 887 Comm: bluetoothd Not tainted 6.10.11-1-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x9a/0xa0
...
__list_add_valid_or_report+0x9a/0xa0
proto_register+0x2b5/0x340
iso_init+0x23/0x150 [bluetooth]
set_iso_socket_func+0x68/0x1b0 [bluetooth]
kmem_cache_free+0x308/0x330
hci_sock_sendmsg+0x990/0x9e0 [bluetooth]
__sock_sendmsg+0x7b/0x80
sock_write_iter+0x9a/0x110
do_iter_readv_writev+0x11d/0x220
vfs_writev+0x180/0x3e0
do_writev+0xca/0x100
...
This change removes the early return. The check for iso_debugfs being
NULL was unnecessary, it is always NULL when iso_inited is false.
Cc: stable@vger.kernel.org
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Unexport nr_irqs and declare it static now that all code that reads or
modifies nr_irqs has been converted to number_of_interrupts() /
set_number_of_interrupts(). Change the type of 'nr_irqs' from 'int' into
'unsigned int' to match the return type and argument type of the
irq_get_nr_iqs() / irq_set_nr_irqs() functions.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-23-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Cache the result of this function in a local variable in
order not to rely on CSE (common subexpression elimination). Prepare
for changing 'nr_irqs' from an exported global variable into a variable
with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-22-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-21-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-20-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-19-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-18-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-17-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-16-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-15-bvanassche@acm.org
