Implement required changes for mode validation and compute config,
to support Ultrajoiner.
v2:
-Drop changes for HDMI.
-Separate out DSC changes into another patch.
v3: Fix check in can_ultrajoiner. (Ankit)
v4:
-Unify helper to check joiner requirement. (Ville)
-Split patches for ultrajoiner changes for max dsc slices and compressed
bpp.(Ankit)
v5: Fix check for joiner. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-12-ankit.k.nautiyal@intel.com
When bigjoiner is used, we need at least 2 dsc slices per pipe.
Modify the condition in intel_dp_dsc_get_slice_count() to reflect the
same.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-11-ankit.k.nautiyal@intel.com
Add compressed bpp limitations for ultrajoiner.
v2: Fix the case for 1 pipe. (Ankit)
v3: Refactor existing helper separately and add only ultrajoiner
limitation. (Ville)
v4: Separate out function for ultrajoiner_ram_bits.
v5: Make the helper function more concise. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-10-ankit.k.nautiyal@intel.com
Streamline the helper to get max compressed bpp for bigjoiner case, to
effectively use num of pipes joined. This will make the addition of
ultrajoiner limitations easier and improve redability.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-9-ankit.k.nautiyal@intel.com
Currently compressed max_bpp limitations for small joiner ram, big joiner
etc are intermingled. Seprate these limitations into separate functions.
v2: Use num_joined_pipes in small joiner ram helper and other minor
fixes. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-8-ankit.k.nautiyal@intel.com
Add changes to DSC which are required for Ultrajoiner.
v2:
-Use correct helper for setting bits for bigjoiner secondary. (Ankit)
-Use primary/secondary instead of master/slave. (Suraj)
v3: Add the ultrajoiner helpers and use it for setting ultrajoiner
bits (Ankit)
v4: Use num_vdsc_instances *= num_joined_pipes (Ville)
v5: Align the helper to get ultrajoiner enabled pipes with other helpers
(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-7-ankit.k.nautiyal@intel.com
Ultrajoiner mode has some new bits and states to be
read out from the hw. Lets make changes accordingly.
v2: Fix checkpatch warnings. (Ankit)
v3: Add separate functions for computing expected secondary_big/ultrajoiner
pipes. (Ankit)
v4:
-Streamline the helpers for ultrajoiner. (Ville)
-Add fixup to accommodate PIPED check for ultrajoiner. (Ville)
-Add more Ultrajoiner drm_WARNs. (Ville)
v5: Remove spurious newline. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-6-ankit.k.nautiyal@intel.com
Pass the current pipe into enabled_joiner_pipes(), and let it figure out
the proper bitmasks for us. Since the enabled_joiner_pipes now gets the
primary and secondary pipes wrt a given pipe, the helpers
to get primary pipe and secondary pipes are no longer required.
v2:
-Simplify helper get_joiner_primary_pipes. (Ville)
-Nuke get_joiner_secondary_pipes. (Ville)
-Add more drm_WARNs final primary/secondary pipes. (Ville)
v3: Drop ultrajoiner stuff and add it in subsequent patches. (Ville)
v4:
-Replace input variable name primary_pipes to primary_pipe for
enabled_joiner_pipes()
-Avoid get_joiner_primary_pipe and use primary_pipes set by
enabled_joiner_pipes(). (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-5-ankit.k.nautiyal@intel.com
Add sanity checks for primary and secondary bigjoiner/uncompressed
bitmasks, should make it easier to spot possible issues.
v2:
-Streamline the expected masks and add few more drm_WARNs. (Ville)
-Use %#x format specifier for printing joiner masks. (Ville)
-Use struct intel_display instead of struct drm_i915_private. (Ankit)
v3:
-Rename helper to get expected uncompressed joiner pipes. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-3-ankit.k.nautiyal@intel.com
The value is read from the register TXGBE_RX_GEN_CTL3, and it should be
written back to TXGBE_RX_GEN_CTL3 when it changes some fields.
Cc: stable@vger.kernel.org
Fixes: f629acc6f2 ("net: pcs: xpcs: support to switch mode for Wangxun NICs")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20240924022857.865422-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We need to add a new sanity checks and also do
some preparations for adding ultrajoiner hw state readout.
Lets first split reading of the uncompressed joiner and bigjoiner
bit masks into separate functions.
v2: Fixed checkpatch warnings (Ankit)
v3: Use struct intel_display in the new functions. (Ankit)
v4: Use check for bigjoiner before reading the regs. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-2-ankit.k.nautiyal@intel.com
When applying padding, the buffer is not zeroed, which results in memory
disclosure. The mentioned data is observed on the wire. This patch uses
skb_put_padto() to pad Ethernet frames properly. The mentioned function
zeroes the expanded buffer.
In case the packet cannot be padded it is silently dropped. Statistics
are also not incremented. This driver does not support statistics in the
old 32-bit format or the new 64-bit format. These will be added in the
future. In its current form, the patch should be easily backported to
stable versions.
Ethernet MACs on Amazon-SE and Danube cannot do padding of the packets
in hardware, so software padding must be applied.
Fixes: 504d4721ee ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240923214949.231511-2-olek2@wp.pl
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 24ab059d2e ("net: check dev->gso_max_size in gso_features_check()")
added a dev->gso_max_size test to gso_features_check() in order to fall
back to GSO when needed.
This was added as it was noticed that some drivers could misbehave if TSO
packets get too big. However, the check doesn't respect dev->gso_ipv4_max_size
limit. For instance, a device could be configured with BIG TCP for IPv4,
but not IPv6.
Therefore, add a netif_get_gso_max_size() equivalent to netif_get_gro_max_size()
and use the helper to respect both limits before falling back to GSO engine.
Fixes: 24ab059d2e ("net: check dev->gso_max_size in gso_features_check()")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240923212242.15669-2-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a small netif_get_gro_max_size() helper which returns the maximum IPv4
or IPv6 GRO size of the netdevice.
We later add a netif_get_gso_max_size() equivalent as well for GSO, so that
these helpers can be used consistently instead of open-coded checks.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240923212242.15669-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix a checkpatch --strict issue:
CHECK: Alignment should match open parenthesis
#48: FILE: drivers/reset/amlogic/reset-meson-common.c:48:
+static int meson_reset_level(struct reset_controller_dev *rcdev,
+ unsigned long id, bool assert)
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240930-reset-align-amlogic-v1-1-f64ed5c4efc1@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for the reset controller present in the audio clock
controller of the g12 and sm1 SoC families, using the auxiliary bus.
This is expected to replace the driver currently present directly
within the related clock driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-9-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
To prepare the addition of the auxiliary device support, split
out the device coomon functions from the probe of the platform device.
The device core function will be common to both the platform and auxiliary
driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-8-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The meson reset driver will be split in two part, one implemeting the ops,
the other providing the platform driver support. This will be done to
facilitate the addition of the auxiliary bus support.
To avoid making a mess in drivers/reset/ while doing so, move the amlogic
reset drivers to a dedicated directory.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-7-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a callback to check the status of the level reset, as done in
the reset driver of the audio clock controller.
This is done keep the functionality when the audio reset controller
get migrated to meson-reset.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-6-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The reset driver from audio clock controller may register less
reset than a register can hold. To avoid making any change while
switching to auxiliary support, use the number of reset instead of the
register count to define the bounds of the reset controller.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-5-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
To allow using the same driver for the main reset controller and the
auxiliary ones embedded in the clock controllers, allow to customise
the reset offset, same as the level offset. Also add an option to make
the level reset active low or high.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-4-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
register count and offset cannot be negative. Use unsigned integer
for this.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-3-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no need to use the DT specific function to get
matching data, use the generic one instead
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-2-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
To allow using the same driver for the main reset controller and the
auxiliary ones embedded in the clock controllers, convert the
the Amlogic reset driver to regmap.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-1-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The constructor of ConfigMainWindow() calls show*View(), which needs
to calculate symbol values. conf_read() must be called before that.
Fixes: 060e05c3b4 ("kconfig: qconf: remove initial call to conf_changed()")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Since commit 95573cac25 ("kconfig: cache expression values"), xconfig
emits a lot of false-positive "unmet direct dependencies" warnings.
While conf_read() clears val_is_valid flags, 'make xconfig' calculates
symbol values even before the conf_read() call. This is another issue
that should be addressed separately, but it has revealed that the
val_is_valid field is not initialized.
Fixes: 95573cac25 ("kconfig: cache expression values")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Alexander Sverdlin presents 2 problems during shutdown with the
lan9303 driver. One is specific to lan9303 and the other just happens
to reproduce there.
The first problem is that lan9303 is unique among DSA drivers in that it
calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown,
not remove):
phy_state_machine()
-> ...
-> dsa_user_phy_read()
-> ds->ops->phy_read()
-> lan9303_phy_read()
-> chip->ops->phy_read()
-> lan9303_mdio_phy_read()
-> dev_get_drvdata()
But we never stop the phy_state_machine(), so it may continue to run
after dsa_switch_shutdown(). Our common pattern in all DSA drivers is
to set drvdata to NULL to suppress the remove() method that may come
afterwards. But in this case it will result in an NPD.
The second problem is that the way in which we set
dp->conduit->dsa_ptr = NULL; is concurrent with receive packet
processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL,
but afterwards, rather than continuing to use that non-NULL value,
dev->dsa_ptr is dereferenced again and again without NULL checks:
dsa_conduit_find_user() and many other places. In between dereferences,
there is no locking to ensure that what was valid once continues to be
valid.
Both problems have the common aspect that closing the conduit interface
solves them.
In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN
event in dsa_user_netdevice_event() which closes user ports as well.
dsa_port_disable_rt() calls phylink_stop(), which synchronously stops
the phylink state machine, and ds->ops->phy_read() will thus no longer
call into the driver after this point.
In the second case, dev_close(conduit) should do this, as per
Documentation/networking/driver.rst:
| Quiescence
| ----------
|
| After the ndo_stop routine has been called, the hardware must
| not receive or transmit any data. All in flight packets must
| be aborted. If necessary, poll or wait for completion of
| any reset commands.
So it should be sufficient to ensure that later, when we zeroize
conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call
on this conduit.
The addition of the netif_device_detach() function is to ensure that
ioctls, rtnetlinks and ethtool requests on the user ports no longer
propagate down to the driver - we're no longer prepared to handle them.
The race condition actually did not exist when commit 0650bf52b3
("net: dsa: be compatible with masters which unregister on shutdown")
first introduced dsa_switch_shutdown(). It was created later, when we
stopped unregistering the user interfaces from a bad spot, and we just
replaced that sequence with a racy zeroization of conduit->dsa_ptr
(one which doesn't ensure that the interfaces aren't up).
Reported-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Closes: https://lore.kernel.org/netdev/2d2e3bba17203c14a5ffdabc174e3b6bbb9ad438.camel@siemens.com/
Closes: https://lore.kernel.org/netdev/c1bf4de54e829111e0e4a70e7bd1cf523c9550ff.camel@siemens.com/
Fixes: ee534378f0 ("net: dsa: fix panic when DSA master device unbinds on shutdown")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20240913203549.3081071-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CONFIG_DRM_I915_USERFAULT_AUTOSUSPEND is an int, defaulting to 250. When
the wakeref is non-zero, it's either -1 or a dynamically allocated
pointer, depending on CONFIG_DRM_I915_DEBUG_RUNTIME_PM. It's likely that
the code works by coincidence with the bitwise AND, but with
CONFIG_DRM_I915_DEBUG_RUNTIME_PM=y, there's the off chance that the
condition evaluates to false, and intel_wakeref_auto() doesn't get
called. Switch to the intended logical AND.
v2: Use != to avoid clang -Wconstant-logical-operand (Nathan)
Fixes: ad74457a6b ("drm/i915/dgfx: Release mmap on rpm suspend")
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org # v6.1+
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> # v1
Link: https://patchwork.freedesktop.org/patch/msgid/643cc0a4d12f47fd8403d42581e83b1e9c4543c7.1726680898.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 4c1bfe259e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
GPIOs showed up as unclaimed, so they could be muxed to something else
even though they were in use. Mark GPIOs as claimed to avoid that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240930191523.7030-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
GPIOs showed up as unclaimed in debugfs, so they could be muxed to
something else even though they were in use. Mark GPIOs as claimed when
in use to avoid that.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/2862093f7701dcaf29f37c0b2f9268234168338f.1727711124.git.geert+renesas@glider.be
Add compatible for the cpufreq engine representing support on SA8255p.
Signed-off-by: Nikunj Kela <quic_nkela@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The definition of _update_set_required_opps() has been removed since
commit e37440e7e2 ("OPP: Call dev_pm_opp_set_opp() for required
OPPs").
Besides, the definition of _put_opp_list_kref() has been removed since
commit 03758d6026 ("opp: Replace list_kref with a local counter").
Let's remove the empty declarations in header file.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
devm_kasprintf() can return a NULL pointer on failure but this
returned value in qcom_socinfo_probe() is not checked.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20240929072349.202520-1-hanchunchao@inspur.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If CREATE was successful but SMB2_OP_SET_REPARSE failed then remove the
intermediate object created by CREATE. Otherwise empty object stay on the
server when reparse call failed.
This ensures that if the creating of special files is unsupported by the
server then no empty file stay on the server as a result of unsupported
operation.
Fixes: 102466f303 ("smb: client: allow creating special files via reparse points")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20240930112121.95324-25-Julia.Lawall@inria.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SC7280 and derivative platforms GPU by default requires a signed
binary, a660_zap.mbn. Disable GPU by default and enable it only when
the binary is actually available (QCM6490-IDP, RB3gen2). ChromeOS
devices do not use TrustZone, so GPU can be enabled by default in
sc7280-chrome-common.dtsi. FairPhone5 and SHIFTphone8 DTS already
enable GPU (even though it wasn't required beforehand).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-rb3g2-fixes-v1-2-eb9da98e9f80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Newer boards should always use squashed MBN firmware instead of split
MDT+bNN. Use qcom/qcs6490/modem.mbn as the firmware for the modem on
RB3gen2.
Fixes: ac6d35b9b7 ("arm64: dts: qcom: qcs6490-rb3gen2: Enable various remoteprocs")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-rb3g2-fixes-v1-1-eb9da98e9f80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
commit 8b90269ee6 ("MAINTAINERS: Split Qualcomm SoC and linux-arm-msm
entries") included an entry for .../bindings/reserved-memory/qcom.
However, it appears that this should have been a glob as although
there are files that start with that path, no file matches that exact
path.
Address this by making the entry a glob.
Flagged by make htmldocs as:
Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/reserved-memory/qcom
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240908-qcom-glob-v1-1-94a390f36744@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The current way of storing the configuration is very much
unmaintainable. Convert the data to use designated initializers to make
it easier both to understand and add/update the slice configuration
data.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240910-topic-llcc_unwrap-v2-1-f0487c983373@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Matthieu Baerts says:
====================
In this series from Geliang, modifying MPTCP BPF selftests, we have:
- A new MPTCP subflow BPF program setting socket options per subflow: it
looks better to have this old test program in the BPF selftests to
track regressions and to serve as example.
Note: Nicolas is no longer working at Tessares, but he did this work
while working for them, and his email address is no longer available.
- A new hook in the same BPF program to do the verification step.
- A new MPTCP BPF subtest validating the new BPF program added in the
first patch, with the help of the new hook added in the second patch.
---
Changes in v7:
- Patch 2/3: use 'can_loop' instead of 'cond_break'. (Martin)
- Patch 3/3: use bpf_program__attach_cgroup(). (Martin)
- Link to v6: https://lore.kernel.org/r/20240911-upstream-bpf-next-20240506-mptcp-subflow-test-v6-0-7872294c466b@kernel.org
Changes in v6:
- Patch 3/3: use usleep() instead of sleep()
- Series: rebased on top of bpf-next/net
- Link to v5: https://lore.kernel.org/r/20240910-upstream-bpf-next-20240506-mptcp-subflow-test-v5-0-2c664a7da47c@kernel.org
Changes in v5:
- See the individual changelog for more details about them
- Patch 1/3: set TCP on the 2nd subflow
- Patch 2/3: new
- Patch 3/3: use the BPF program from patch 2/3 to do the validation
instead of using ss.
- Series: rebased on top of bpf-next/net
- Link to v4: https://lore.kernel.org/r/20240805-upstream-bpf-next-20240506-mptcp-subflow-test-v4-0-2b4ca6994993@kernel.org
Changes in v4:
- Drop former patch 2/3: MPTCP's pm_nl_ctl requires a new header file:
- I will check later if it is possible to avoid having duplicated
header files in tools/include/uapi, but no need to block this series
for that. Patch 2/3 can be added later if needed.
- Patch 2/2: skip the test if 'ip mptcp' is not available.
- Link to v3: https://lore.kernel.org/r/20240703-upstream-bpf-next-20240506-mptcp-subflow-test-v3-0-ebdc2d494049@kernel.org
Changes in v3:
- Sorry for the delay between v2 and v3, this series was conflicting
with the "add netns helpers", but it looks like it is on hold:
https://lore.kernel.org/cover.1715821541.git.tanggeliang@kylinos.cn
- Patch 1/3 includes "bpf_tracing_net.h", introduced in between.
- New patch 2/3: "selftests/bpf: Add mptcp pm_nl_ctl link".
- Patch 3/3: use the tool introduced in patch 2/3 + SYS_NOFAIL() helper.
- Link to v2: https://lore.kernel.org/r/20240509-upstream-bpf-next-20240506-mptcp-subflow-test-v2-0-4048c2948665@kernel.org
Changes in v2:
- Previous patches 1/4 and 2/4 have been dropped from this series:
- 1/4: "selftests/bpf: Handle SIGINT when creating netns":
- A new version, more generic and no longer specific to MPTCP BPF
selftest will be sent later, as part of a new series. (Alexei)
- 2/4: "selftests/bpf: Add RUN_MPTCP_TEST macro":
- Removed, not to hide helper functions in macros. (Alexei)
- The commit message of patch 1/2 has been clarified to avoid some
possible confusions spot by Alexei.
- Link to v1: https://lore.kernel.org/r/20240507-upstream-bpf-next-20240506-mptcp-subflow-test-v1-0-e2bcbdf49857@kernel.org
---
Geliang Tang (2):
selftests/bpf: Add getsockopt to inspect mptcp subflow
selftests/bpf: Add mptcp subflow subtest
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch adds a subtest named test_subflow in test_mptcp to load and
verify the newly added MPTCP subflow BPF program. To goal is to make
sure it is possible to set different socket options per subflows, while
the userspace socket interface only lets the application to set the same
socket options for the whole MPTCP connection and its multiple subflows.
To check that, a client and a server are started in a dedicated netns,
with veth interfaces to simulate multiple paths. They will exchange data
to allow the creation of an additional subflow.
When the different subflows are being created, the new MPTCP subflow BPF
program will set some socket options: marks and TCP CC. The validation
is done by the same program, when the userspace checks the value of the
modified socket options. On the userspace side, it will see that the
default values are still being used on the MPTCP connection, while the
BPF program will see different options set per subflow of the same MPTCP
connection.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/76
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240926-upstream-bpf-next-20240506-mptcp-subflow-test-v7-3-d26029e15cdd@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch adds a "cgroup/getsockopt" way to inspect the subflows of an
MPTCP socket, and verify the modifications done by the same BPF program
in the previous commit: a different mark per subflow, and a different
TCP CC set on the second one. This new hook will be used by the next
commit to verify the socket options set on each subflow.
This extra "cgroup/getsockopt" prog walks the msk->conn_list and use
bpf_core_cast to cast a pointer for readonly. It allows to inspect all
the fields of a structure.
Note that on the kernel side, the MPTCP socket stores a list of subflows
under 'msk->conn_list'. They can be iterated using the generic 'list'
helpers. They have been imported here, with a small difference:
list_for_each_entry() uses 'can_loop' to limit the number of iterations,
and ease its use. Because only data need to be read here, it is enough
to use this technique. It is planned to use bpf_iter, when BPF programs
will be used to modify data from the different subflows.
mptcp_subflow_tcp_sock() and mptcp_for_each_stubflow() helpers have also
be imported.
Suggested-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240926-upstream-bpf-next-20240506-mptcp-subflow-test-v7-2-d26029e15cdd@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Move Nicolas' patch into bpf selftests directory. This example adds a
different mark (SO_MARK) on each subflow, and changes the TCP CC only on
the first subflow.
From the userspace, an application can do a setsockopt() on an MPTCP
socket, and typically the same value will be propagated to all subflows
(paths). If someone wants to have different values per subflow, the
recommended way is to use BPF. So it is good to add such example here,
and make sure there is no regressions.
This example shows how it is possible to:
Identify the parent msk of an MPTCP subflow.
Put different sockopt for each subflow of a same MPTCP connection.
Here especially, two different behaviours are implemented:
A socket mark (SOL_SOCKET SO_MARK) is put on each subflow of a same
MPTCP connection. The order of creation of the current subflow defines
its mark. The TCP CC algorithm of the very first subflow of an MPTCP
connection is set to "reno".
This is just to show it is possible to identify an MPTCP connection, and
set socket options, from different SOL levels, per subflow. "reno" has
been picked because it is built-in and usually not set as default one.
It is easy to verify with 'ss' that these modifications have been
applied correctly. That's what the next patch is going to do.
Nicolas' code comes from:
commit 4d120186e4d6 ("bpf:examples: update mptcp_set_mark_kern.c")
from the MPTCP repo https://github.com/multipath-tcp/mptcp_net-next (the
"scripts" branch), and it has been adapted by Geliang.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/76
Co-developed-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Nicolas Rybowski <nicolas.rybowski@tessares.net>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240926-upstream-bpf-next-20240506-mptcp-subflow-test-v7-1-d26029e15cdd@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
