Improve robustness by checking for a lost BSY signal during the information
transfer loop. The status register is being polled anyway, so a BSY check
costs nothing. BSY signal loss could be caused by a target error or a
kicked plug etc. A bus reset is another possibility but that is already
handled and hostdata->connected would be NULL.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/d253dddaf4d9bc17b8ee02ea2b731d92f25b16f1.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following an incomplete transfer in MSG IN phase, the driver would not
notice the problem and would make use of invalid data. Initialize 'tmp'
appropriately and bail out if no message was received. For STATUS phase,
preserve the existing status code unless a new value was transferred.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/52e02a8812ae1a2d810d7f9f7fd800c3ccc320c4.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that FLAG_DMA_FIXUP has itself been fixed up, it can be used to enable
scatter/gather. Increase the default value for sg_tablesize to SG_ALL for
those systems which are compatible with FLAG_DMA_FIXUP.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/f155ba5ce93055cbc6ac6d4026673f40f826edb8.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's not an error for a target to change the bus phase during a transfer.
Unfortunately, the FLAG_DMA_FIXUP workaround does not allow for that -- a
phase change produces a DRQ timeout error and the device borken flag will
be set.
Check the phase match bit during FLAG_DMA_FIXUP processing. Don't forget to
decrement the command residual. While we are here, change shost_printk()
into scmd_printk() for better consistency with other DMA error messages.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 55181be8ce ("ncr5380: Replace redundant flags with FLAG_NO_DMA_FIXUP")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/99dc7d1f4c825621b5b120963a69f6cd3e9ca659.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SD cards can produce write latency spikes on the order of a hundred
milliseconds. If the target firmware does not hide that latency during DATA
IN and OUT phases it can cause the PDMA circuitry to raise a processor bus
fault which in turn leads to an unreliable byte count and a DMA overrun.
The Last Byte Sent flag is used to detect the overrun but this mechanism is
unreliable on some systems. Instead, set a DID_ERROR result whenever there
is a bus fault during a PDMA send, unless the cause was a phase mismatch.
Cc: stable@vger.kernel.org # 5.15+
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 7c1f3e3447 ("scsi: mac_scsi: Treat Last Byte Sent time-out as failure")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/cc38df687ace2c4ffc375a683b2502fc476b600d.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before the error handling can be revised, some preparation is needed.
Refactor the polling loop with a new function, macscsi_wait_for_drq().
This function will gain more call sites in the next patch.
Cc: stable@vger.kernel.org # 5.15+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/6a5ffabb4290c0d138c6d285fda8fa3902e926f0.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a bus fault, capture and log the chip registers immediately, if the
NDEBUG_PSEUDO_DMA macro is defined. Remove some printk(KERN_DEBUG ...)
messages that aren't needed any more. Don't skip the debug message when
bytes == 0. Show all of the byte counters in the debug messages.
Cc: stable@vger.kernel.org # 5.15+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/7573c79f4e488fc00af2b8a191e257ca945e0409.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make __fdget() et.al. return struct fd directly.
New helpers: BORROWED_FD(file) and CLONED_FD(file), for
borrowed and cloned file references resp.
NOTE: this might need tuning; in particular, inline on
__fget_light() is there to keep the code generation same as
before - we probably want to keep it inlined in fdget() et.al.
(especially so in fdget_pos()), but that needs profiling.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We want the compiler to see that fdput() on empty instance
is a no-op. The emptiness check is that file reference is NULL,
while fdput() is "fput() if FDPUT_FPUT is present in flags".
The reason why fdput() on empty instance is a no-op is something
compiler can't see - it's that we never generate instances with
NULL file reference combined with non-zero flags.
It's not that hard to deal with - the real primitives behind
fdget() et.al. are returning an unsigned long value, unpacked by (inlined)
__to_fd() into the current struct file * + int. The lower bits are
used to store flags, while the rest encodes the pointer. Linus suggested
that keeping this unsigned long around with the extractions done by inlined
accessors should generate a sane code and that turns out to be the case.
Namely, turning struct fd into a struct-wrapped unsinged long, with
fd_empty(f) => unlikely(f.word == 0)
fd_file(f) => (struct file *)(f.word & ~3)
fdput(f) => if (f.word & 1) fput(fd_file(f))
ends up with compiler doing the right thing. The cost is the patch
footprint, of course - we need to switch f.file to fd_file(f) all over
the tree, and it's not doable with simple search and replace; there are
false positives, etc.
Note that the sole member of that structure is an opaque
unsigned long - all accesses should be done via wrappers and I don't
want to use a name that would invite manual casts to file pointers,
etc. The value of that member is equal either to (unsigned long)p | flags,
p being an address of some struct file instance, or to 0 for an empty fd.
For now the new predicate (fd_empty(f)) has no users; all the
existing checks have form (!fd_file(f)). We will convert to fd_empty()
use later; here we only define it (and tell the compiler that it's
unlikely to return true).
This commit only deals with representation change; there will
be followups.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For any changes of struct fd representation we need to
turn existing accesses to fields into calls of wrappers.
Accesses to struct fd::flags are very few (3 in linux/file.h,
1 in net/socket.c, 3 in fs/overlayfs/file.c and 3 more in
explicit initializers).
Those can be dealt with in the commit converting to
new layout; accesses to struct fd::file are too many for that.
This commit converts (almost) all of f.file to
fd_file(f). It's not entirely mechanical ('file' is used as
a member name more than just in struct fd) and it does not
even attempt to distinguish the uses in pointer context from
those in boolean context; the latter will be eventually turned
into a separate helper (fd_empty()).
NOTE: mass conversion to fd_empty(), tempting as it
might be, is a bad idea; better do that piecewise in commit
that convert from fdget...() to CLASS(...).
[conflicts in fs/fhandle.c, kernel/bpf/syscall.c, mm/memcontrol.c
caught by git; fs/stat.c one got caught by git grep]
[fs/xattr.c conflict]
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add the pinctrl node in the device tree in order to enable the
S32G2/S32G3 pinctrl driver to probe.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of updating the ConsumerIndex of the Admin and Operational
ReplyQueues after processing all replies in the queue, the index will now
be periodically updated after processing every 100 replies.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240808125418.8832-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver masked the loginfo available bit in the iocstatus before passing
it to the applications, causing a mismatch in error messages between Linux
and other operating systems.
Modify driver to return unmasked (complete) iocstatus, including the
loginfo available bit, for the MPI commands sent through the ioctl
interface.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240808125418.8832-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
we are *not* guaranteed that anything past the terminating NUL
is mapped (let alone initialized with anything sane).
Fixes: 0dea116876 ("cgroup: implement eventfd-based generic API for notifications")
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- disable PU/PD if already done with external resistors
- do not configure Schmitt Trigger for outputs
- do not configure DSE / FSEL for inputs
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM starts at 0x80000000.
Fixes: c982ecfa79 ("arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 9748dbc9f2 ("net/smc: Avoid -Wflex-array-member-not-at-end
warnings") introduced tagged `struct smc_clc_v2_extension_fixed` and
`struct smc_clc_smcd_v2_extension_fixed`. We want to ensure that when
new members need to be added to the flexible structures, they are
always included within these tagged structs.
So, we use `static_assert()` to ensure that the memory layout for
both the flexible structure and the tagged struct is the same after
any changes.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Link: https://patch.msgid.link/ZrVBuiqFHAORpFxE@cute
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d88cabfd9a ("nfp: Avoid -Wflex-array-member-not-at-end
warnings") introduced tagged `struct nfp_dump_tl_hdr`. We want
to ensure that when new members need to be added to the flexible
structure, they are always included within this tagged struct.
So, we use `static_assert()` to ensure that the memory layout for
both the flexible structure and the tagged struct is the same after
any changes.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ZrVB43Hen0H5WQFP@cute
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In macb_suspend(), idev->ifa_list is fetched with rcu_access_pointer()
and later the pointer is dereferenced as ifa->ifa_local.
So, idev->ifa_list must be fetched with rcu_dereference().
Fixes: 0cb8de39a7 ("net: macb: Add ARP support to WOL")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240808040021.6971-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A selftest is added such that without the previous patch,
a crash can happen. With the previous patch, the test can
run successfully. The new test is written in a way which
mimics original crash case:
main_prog
static_prog_1
static_prog_2
where static_prog_1 has different paths to static_prog_2
and some path has stack allocated and some other path
does not. A stacksafe() checking in static_prog_2()
triggered the crash.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240812214852.214037-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Hodges reported a kernel verifier crash when playing with sched-ext.
Further investigation shows that the crash is due to invalid memory access
in stacksafe(). More specifically, it is the following code:
if (exact != NOT_EXACT &&
old->stack[spi].slot_type[i % BPF_REG_SIZE] !=
cur->stack[spi].slot_type[i % BPF_REG_SIZE])
return false;
The 'i' iterates old->allocated_stack.
If cur->allocated_stack < old->allocated_stack the out-of-bound
access will happen.
To fix the issue add 'i >= cur->allocated_stack' check such that if
the condition is true, stacksafe() should fail. Otherwise,
cur->stack[spi].slot_type[i % BPF_REG_SIZE] memory access is legal.
Fixes: 2793a8b015 ("bpf: exact states comparison for iterator convergence checks")
Cc: Eduard Zingerman <eddyz87@gmail.com>
Reported-by: Daniel Hodges <hodgesd@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240812214847.213612-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Remove unnecessary flex-array member `pad[]` and refactor the related
code a bit.
Fix the following warning:
net/sched/act_ct.c:57:29: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/ZrY0JMVsImbDbx6r@cute
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit fc44449411 ("scsi: mpi3mr: HDB allocation and posting for hardware
and firmware buffers") added mpi3mr_alloc_diag_bufs() which calls
dma_alloc_coherent() to allocate the trace buffer and the firmware
buffer. mpi3mr_alloc_diag_bufs() decides the buffer sizes from the driver
configuration. In my environment, the sizes are 8MB. With the sizes,
dma_alloc_coherent() fails and report this WARNING:
WARNING: CPU: 4 PID: 438 at mm/page_alloc.c:4676 __alloc_pages_noprof+0x52f/0x640
The WARNING indicates that the order of the allocation size is larger than
MAX_PAGE_ORDER. After this failure, mpi3mr_alloc_diag_bufs() reduces the
buffer sizes and retries dma_alloc_coherent(). In the end, the buffer
allocations succeed with 4MB size in my environment, which corresponds to
MAX_PAGE_ORDER=10. Though the allocations succeed, the WARNING message is
misleading and should be avoided.
To avoid the WARNING, check the orders of the buffer allocation sizes
before calling dma_alloc_coherent(). If the orders are larger than
MAX_PAGE_ORDER, fall back to the retry path.
Fixes: fc44449411 ("scsi: mpi3mr: HDB allocation and posting for hardware and firmware buffers")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240810042701.661841-3-shinichiro.kawasaki@wdc.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Petr Machata says:
====================
net: nexthop: Increase weight to u16
In CLOS networks, as link failures occur at various points in the network,
ECMP weights of the involved nodes are adjusted to compensate. With high
fan-out of the involved nodes, and overall high number of nodes,
a (non-)ECMP weight ratio that we would like to configure does not fit into
8 bits. Instead of, say, 255:254, we might like to configure something like
1000:999. For these deployments, the 8-bit weight may not be enough.
To that end, in this patchset increase the next hop weight from u8 to u16.
Patch #1 adds a flag that indicates whether the reserved fields are zeroed.
This is a follow-up to a new fix merged in commit 6d745cd0e9 ("net:
nexthop: Initialize all fields in dumped nexthops"). The theory behind this
patch is that there is a strict ordering between the fields actually being
zeroed, the kernel declaring that they are, and the kernel repurposing the
fields. Thus clients can use the flag to tell if it is safe to interpret
the reserved fields in any way.
Patch #2 contains the substantial code and the commit message covers the
details of the changes.
Patches #3 to #6 add selftests.
====================
Link: https://patch.msgid.link/cover.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests that exercise full 16 bits of NH weight.
Like in the previous patch, omit the 255:65535 test when KSFT_MACHINE_SLOW.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/a91d6ead9d1b1b4b7e276ca58a71ef814f42b7dd.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests that exercise full 16 bits of NH weight.
To test the 255:65535, it is necessary to run more packets than for the
other tests. On a debug kernel, the test can take up to a minute, therefore
avoid the test when KSFT_MACHINE_SLOW.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/c0c257c00ad30b07afc3fa5e2afd135925405544.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the context of an offloaded datapath, it may take a while for the ip
link stats to be updated. This causes the test to fail when MZ_DELAY is too
low. Sleep after the packets are sent for the link stats to get up to date.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/8b1971d948273afd7de2da3d6a2ba35200540e55.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In CLOS networks, as link failures occur at various points in the network,
ECMP weights of the involved nodes are adjusted to compensate. With high
fan-out of the involved nodes, and overall high number of nodes,
a (non-)ECMP weight ratio that we would like to configure does not fit into
8 bits. Instead of, say, 255:254, we might like to configure something like
1000:999. For these deployments, the 8-bit weight may not be enough.
To that end, in this patch increase the next hop weight from u8 to u16.
Increasing the width of an integral type can be tricky, because while the
code still compiles, the types may not check out anymore, and numerical
errors come up. To prevent this, the conversion was done in two steps.
First the type was changed from u8 to a single-member structure, which
invalidated all uses of the field. This allowed going through them one by
one and audit for type correctness. Then the structure was replaced with a
vanilla u16 again. This should ensure that no place was missed.
The UAPI for configuring nexthop group members is that an attribute
NHA_GROUP carries an array of struct nexthop_grp entries:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 resvd1;
__u16 resvd2;
};
The field resvd1 is currently validated and required to be zero. We can
lift this requirement and carry high-order bits of the weight in the
reserved field:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 weight_high;
__u16 resvd2;
};
Keeping the fields split this way was chosen in case an existing userspace
makes assumptions about the width of the weight field, and to sidestep any
endianness issues.
The weight field is currently encoded as the weight value minus one,
because weight of 0 is invalid. This same trick is impossible for the new
weight_high field, because zero must mean actual zero. With this in place:
- Old userspace is guaranteed to carry weight_high of 0, therefore
configuring 8-bit weights as appropriate. When dumping nexthops with
16-bit weight, it would only show the lower 8 bits. But configuring such
nexthops implies existence of userspace aware of the extension in the
first place.
- New userspace talking to an old kernel will work as long as it only
attempts to configure 8-bit weights, where the high-order bits are zero.
Old kernel will bounce attempts at configuring >8-bit weights.
Renaming reserved fields as they are allocated for some purpose is commonly
done in Linux. Whoever touches a reserved field is doing so at their own
risk. nexthop_grp::resvd1 in particular is currently used by at least
strace, however they carry an own copy of UAPI headers, and the conversion
should be trivial. A helper is provided for decoding the weight out of the
two fields. Forcing a conversion seems preferable to bending backwards and
introducing anonymous unions or whatever.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/483e2fcf4beb0d9135d62e7d27b46fa2685479d4.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are many unpatched kernel versions out there that do not initialize
the reserved fields of struct nexthop_grp. The issue with that is that if
those fields were to be used for some end (i.e. stop being reserved), old
kernels would still keep sending random data through the field, and a new
userspace could not rely on the value.
In this patch, use the existing NHA_OP_FLAGS, which is currently inbound
only, to carry flags back to the userspace. Add a flag to indicate that the
reserved fields in struct nexthop_grp are zeroed before dumping. This is
reliant on the actual fix from commit 6d745cd0e9 ("net: nexthop:
Initialize all fields in dumped nexthops").
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/21037748d4f9d8ff486151f4c09083bcf12d5df8.1723036486.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
topology_is_core_online() checks if the core a CPU belongs to
is online. The core is online if at least one of the sibling
CPUs is online. The first CPU of an online core is also online
in the common case, so this should be fairly quick.
Fixes: 73c58e7e14 ("powerpc: Add HOTPLUG_SMT support")
Signed-off-by: Nysal Jan K.A <nysal@linux.ibm.com>
Reviewed-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240731030126.956210-3-nysal@linux.ibm.com
If a core is offline then enabling SMT should not online CPUs of
this core. By enabling SMT, what is intended is either changing the SMT
value from "off" to "on" or setting the SMT level (threads per core) from a
lower to higher value.
On PowerPC the ppc64_cpu utility can be used, among other things, to
perform the following functions:
ppc64_cpu --cores-on # Get the number of online cores
ppc64_cpu --cores-on=X # Put exactly X cores online
ppc64_cpu --offline-cores=X[,Y,...] # Put specified cores offline
ppc64_cpu --smt={on|off|value} # Enable, disable or change SMT level
If the user has decided to offline certain cores, enabling SMT should
not online CPUs in those cores. This patch fixes the issue and changes
the behaviour as described, by introducing an arch specific function
topology_is_core_online(). It is currently implemented only for PowerPC.
Fixes: 73c58e7e14 ("powerpc: Add HOTPLUG_SMT support")
Reported-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Closes: https://groups.google.com/g/powerpc-utils-devel/c/wrwVzAAnRlI/m/5KJSoqP4BAAJ
Signed-off-by: Nysal Jan K.A <nysal@linux.ibm.com>
Reviewed-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240731030126.956210-2-nysal@linux.ibm.com
as it doesn't seem to offer anything of value.
There's only 1 trivial user:
int lowpan_ndisc_is_useropt(u8 nd_opt_type) {
return nd_opt_type == ND_OPT_6CO;
}
but there's no harm to always treating that as
a useropt...
Cc: David Ahern <dsahern@kernel.org>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://patch.msgid.link/20240730003010.156977-1-maze@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In core function, the instances of some client resource structures are
maintained by IDR. As of kernel v6.0, IDR has been superseded by XArray
and deprecated.
This commit replaces the usage of IDR with XArray to maintain the
resource instances. The instance of XArray is allocated per client with
XA_FLAGS_ALLOC1 so that the index of allocated entry is greater than zero
and returns to user space client as handle of the resource.
Link: https://lore.kernel.org/r/20240812235210.28458-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
This commit is a preparation to use xa_for_each() macro. Current
implementation uses idr_for_each() function and has a disadvantage to
replace with the macro. The IDR framework has idr_for_each_entry() macro
for the similar purpose. This commit replace the function with the
macro with minor code refactoring.
Link: https://lore.kernel.org/r/20240812235210.28458-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
It depends on the function assigned to release member to identify
resource structure.
This commit adds a helper function to identify iso_resource structure.
Link: https://lore.kernel.org/r/20240812235210.28458-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
All of local resource structure commonly have data of client_resource type
in its first member. This design sometimes requires usage of
container_of to retrieve parent structure by the first member.
This commit adds some helper functions for this purpose.
Link: https://lore.kernel.org/r/20240812235210.28458-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Wa_14021821874 applies to xe2_hpg
V2(Himal):
- Use space after define
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240812134117.813670-1-tejas.upadhyay@intel.com
Implement netdev_stat_ops and export the basic per-queue stats.
This interface expect users to set the values that are used
either to zero or to some other preserved value (they are 0xff by
default). So here we export bytes/packets/drops from tx and rx_stats
plus set some of the values that are exposed by queue stats
to zero.
$ cd tools/testing/selftests/drivers/net && ./stats.py
[...]
Totals: pass:4 fail:0 xfail:0 xpass:0 skip:0 error:0
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20240810054322.2766421-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Count packets, bytes and drop on the datapath, and report
to the user. Since queues are completely freed when the
device is down - accumulate the stats in the main netdev struct.
This means that per-queue stats will only report values since
last reset (per qstat recommendation).
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20240810054322.2766421-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce tracepoints to allow tracing the GLINK packets being exchanged
with other subsystems. This is useful for debugging both interaction
with remote processors and client driver issues, as well as tracking
latency through the communication stack.
Channel events are traced with both local and remote channel ids, as
well as the textual representation when possible. The channel ids are
useful when matching traces with traces from the firmware side logs,
while the textual representation is necessary to identify channels when
we're starting to trace an already running system.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20240805-glink-tracepoints-v1-3-a5f3293fb09e@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Align the qcom_glink_send_close_ack() arguments with other functions to
take the struct glink_channel, so that the upcoming tracepoint patch can
access the channel attributes.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20240805-glink-tracepoints-v1-2-a5f3293fb09e@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The operation of advancing the FIFO receive pointer is sprinkled between
the interrupt handler itself, and functions being called from this.
Push all the RX advancement operations to the individual handlers, to
unify the style across the handling of the various messages.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20240805-glink-tracepoints-v1-1-a5f3293fb09e@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
