SII9022 and TVE are connected with IPU DI0 and IPU DI1 respectively, so
they are in two different display pipelines and may run simultaneously.
Keep TVE being enabled as imx53-qsb-common.dtsi does by not setting it's
status property to "disabled".
Fixes: eeb403df95 ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These properties are required by i2c-controller.yaml bindings.
Add them on SoC level, rather than on board level.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pawel Dembicki says:
====================
net: dsa: vsc73xx: fix MDIO bus access and PHY opera
This series are extracted patches from net-next series [0].
The VSC73xx driver has issues with PHY configuration. This patch series
fixes most of them.
The first patch synchronizes the register configuration routine with the
datasheet recommendations.
Patches 2-3 restore proper communication on the MDIO bus. Currently,
the write value isn't sent to the MDIO register, and without a busy check,
communication with the PHY can be interrupted. This causes the PHY to
receive improper configuration and autonegotiation could fail.
The fourth patch removes the PHY reset blockade, as it is no longer
required.
After fixing the MDIO operations, autonegotiation became possible.
The last patch removes the blockade, which became unnecessary after
the MDIO operations fix.
[0] https://patchwork.kernel.org/project/netdevbpf/list/?series=874739&state=%2A&archive=both
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vsc73xx mdio bus work properly, the generic autonegotiation
configuration works well.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the VSC73xx PHY was problematic because the MDIO bus, without
a busy check, read and wrote incorrect register values.
My investigation indicates that resetting the PHY only triggers changes
in configuration. However, improper register values written earlier
were only exposed after a soft reset.
The reset itself wasn't the issue; rather, the problem stemmed from
incorrect read and write operations.
A 'soft_reset' can now proceed normally. There are no reasons to keep
the VSC73xx from being reset.
This commit removes the reset blockade in the 'vsc73xx_phy_write'
function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet description ("Port Mode Procedure" in 5.6.2),
the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode.
The WEXC_DIS bit is responsible for MAC behavior after an excessive
collision. Let's set it as described in the datasheet.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rkisp1-params driver assumes the data buffer format is the only
currently supported "fixed" one. The usage of the "fixed" format is
assumed when allocating memory for the scratch buffers and when
initializing the vb2 queue.
In order to prepare to support the "extensible" format beside the
existing "fixed" one, add support in the driver for both formats by
caching a pointer to the active one in the driver structure and use it
in the vb2 queue operations and subdev pad operations implementations.
Do not yet allow userspace to select between the two formats as the
support for the "extensible" format parsing will be introduced in a later
patch in the series.
While at it, document the un-documented ycbcr_encoding field of
struct rkisp1_params_ops.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The ISP parameters buffers are queued by userspace to the params video
device and appended by the driver to the list of available buffers for
later consumption.
As the parameters buffer is mapped in the userspace process memory,
applications have access to the buffer content after the buffer has
been queued.
To prevent userspace from modifying the contents of the parameters buffer
after it has been queued to the video device, add to 'struct
rkisp1_params_buffer' a scratch buffer where to copy the parameters.
Allocate the scratch buffer in the vb2 buf_init() operation and copy the
buffer content in the buf_prepare() operation. Free the scratch
buffer in the newly introduced buf_cleanup() operation handler.
Modify the ISP configuration function to access the ISP configuration
from the cached copy of the parameters buffer instead of using the
userspace-mapped one.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Create the 'struct rkisp1_params_buffer' type that wraps a
vb2_v4l2_buffer to prepare to hold a copy of the parameters buffer that
will be used to cache the user-provided configuration buffer in the
following patches.
Replace usage of 'struct rkisp1_buffer' with 'struct
rkisp1_params_buffer' in rkisp1-params.c to prepare for that.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The rkisp1 driver stores ISP configuration parameters in the fixed
rkisp1_params_cfg structure. As the members of the structure are part of
the userspace API, the structure layout is immutable and cannot be
extended further. Introducing new parameters or modifying the existing
ones would change the buffer layout and cause breakages in existing
applications.
The allow for future extensions to the ISP parameters, introduce a new
extensible parameters format, with a new format 4CC. Document usage of
the new format in the rkisp1 admin guide.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add to the rkisp1-config.h header data types and documentation of
the extensible parameters format.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
- RK3399 has input/output limit of main path 4416 x 3312
- PX30 has input/output limit of main path 3264 x 2448
- i.MX8MP has input/output limit of main path 4096 x 3072
Use rkisp1_info struct to encode the limits.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When populating devices from a specific node, we don't need to call
of_platform_populate() for every child node manually - the routine
will already do it. We can call it directly from the platform device's
OF node. While at it: use the managed variant of of_platform_populate().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240809-ti-aemif-v1-3-27b1e5001390@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Remove several lines of code and a jump label by using the managed
variant of clk_get() that also prepares and enables the clock (and
disables and unprepares it on driver detach).
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240809-ti-aemif-v1-2-27b1e5001390@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
There are no longer any users of the ti-aemif driver that set up platform
data from board files. We can shrink the driver by removing support for
it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240809-ti-aemif-v1-1-27b1e5001390@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Checkpatch complains about the SPDX-License-Identifier being in the
wrong place. Move it to the top of the file to fix these warnings.
In cases of the license being specified only in text, convert these
to the SPDX-License-Identifier.
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/4d41caabb6af5741d92bd5567a04c93a18e2ebe2.1722842067.git.stano.jakubek@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
DT convention is to have property-names after property.
While at it, cleanup indentation for some clocks.
No functional change.
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/13ea4a27f0d1428a925a6f817f9370673eaec938.1722842067.git.stano.jakubek@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Bindings expect the LED and GPIO keys node names to follow certain
pattern, see dtbs_check warnings:
nuvoton-wpcm450-supermicro-x9sci-ln4f.dtb: gpio-keys: 'uid' does not match any of the regexes: '^(button|event|key|switch|(button|event|key|switch)...
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20240701164915.577068-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Various nodes on the Arm Realview boards have missing or spurious
unit-addresses.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240528191510.1444068-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Neither the imx8dxl-evk or imx8qm-mek have a Rohm DAC on them as far as
I can tell from online documentation, and they certainly do not have a
dh2228fv, as this device does not actually exist! Remove the DAC nodes
from the devicetrees as it is not acceptable to pretend to have a device
on a board in order to bind the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In axiethernet header fix register defines comment description to be
inline with IP documentation. It updates MAC configuration register,
MDIO configuration register and frame filter control description.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't dereference "skb" after calling vcc->push() because the skb
is released.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On macOS, as reported by Daniel Gomez, getline() sets ENOTTY to errno
if it is requested to read from /dev/null.
If this is worth fixing, I would rather pass an empty file to
scripts/kallsyms instead of adding the ugly #ifdef __APPLE__.
Fixes: c442db3f49 ("kbuild: remove PROVIDE() for kallsyms symbols")
Reported-by: Daniel Gomez <da.gomez@samsung.com>
Closes: https://lore.kernel.org/all/20240807-macos-build-support-v1-12-4cd1ded85694@samsung.com/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
These files do not use any macros defined in <linux/version.h>.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Micro SD cards can't be physically write-protected like full-sized
cards. Disable this feature in device-tree to get rid of the kernel
warning:
"host does not support reading read-only switch, assuming write-enable"
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_opregion.[ch] to struct intel_display.
v2:
- Fix declarations for !CONFIG_ACPI (Imre, kernel test robot)
- Pass encoder/connector directly to intel_display() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/aef94503909bbbf95f0244dc382a4d4cd050b903.1723213547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch takes care of the following warnings during documentation
compiling:
./include/uapi/drm/drm_mode.h:869: warning: Function parameter or struct member 'width' not described in 'drm_plane_size_hint'
./include/uapi/drm/drm_mode.h:869: warning: Function parameter or struct member 'height' not described in 'drm_plane_size_hint'
Signed-off-by: Mohammed Anees <pvmohammedanees2003@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240811101653.170223-1-pvmohammedanees2003@gmail.com
Add quirk orientation for Ayn Loki Max model.
This has been tested by JELOS team that uses their
own patched kernel for a while now and confirmed by
users in the ChimeraOS discord servers.
Signed-off-by: Bouke Sybren Haarsma <boukehaarsma23@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240728124731.168452-3-boukehaarsma23@gmail.com
Now that kmsg dump callback has the description parameter, use it in
the user panic screen.
This is the string passed to panic(), like "VFS: Unable to mount root
fs on xxx" or "Attempted to kill init! exitcode=0xxxx".
It gives a hint on why the panic occurred, without being too cryptic.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807134902.458669-6-jfalempe@redhat.com
Move the copyright notice to the top of drm_panic.h, and add the
missing Red Hat copyright notice.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807134902.458669-5-jfalempe@redhat.com
drm_panic_[un]register() are only used by the core drm, and are not
intended to be called by other drm drivers, so move their prototypes
to drm_crtc_internal.h.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807134902.458669-4-jfalempe@redhat.com
drm_panic_[un]register() are called only from the core drm, so there
is no need to export them.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807134902.458669-3-jfalempe@redhat.com
There is no space between the last word, and the punctuation mark in
English.
Suggested-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807134902.458669-2-jfalempe@redhat.com
This patch enables the TI TAS2781 amplifier SoC for the ASUS ROG ALLY X.
This is a design change from the original ASUS ROG ALLY, creating the need
for this patch. All other Realtek Codec settings seem to be re-used from
the original ROG ALLY design (on the ROG ALLY X). This patch maintains the
previous settings for the Realtek codec portion, but enables the I2C
binding for the TI TAS2781 amplifier (instead of the Cirrus CS35L41 amp
used on the original ASUS ROG ALLY).
One other requirement must be met for audio to work on the ASUS ROG ALLY X.
A proper firmware file in the correct location with a proper symlink. We
had reached out to TI engineers and confirmed that the firmware found in
the Windows' driver package has a GPL license. Bazzite Github is hosting
this firmware file for now until proper linux-firmware upstreaming can
occur. https://github.com/ublue-os/bazzite
This firmware file should be placed in
/usr/lib/firmware/ti/tas2781/TAS2XXX1EB3.bin with a symlink to it from
/usr/lib/firmware/TAS2XXX1EB3.bin
Co-developed by: Kyle Gospodnetich <me@kylegospodneti.ch>
Signed-off-by: Kyle Gospodnetich <me@kylegospodneti.ch>
Co-developed by: Jan Drogehoff <sentrycraft123@gmail.com>
Signed-off-by: Jan Drogehoff <sentrycraft123@gmail.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Tested-by: Richard Alvarez <alvarez.richard@gmail.com>
Tested-by: Miles Montierth <cyber_dopamine@intheblackmedia.com>
Signed-off-by: Jonathan LoBue <jlobue10@gmail.com>
Link: https://patch.msgid.link/20240812045325.47736-1-jlobue10@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of these laptop models have quirk IDs that are identical but have
different amplifier parts fitted, this difference is described in the
ACPI information.
The solution introduced for this product family can derive the required
component binding information from ACPI instead of hardcoding it,
supports the new variants of the CS35L56 being used and has generalized
naming that makes it applicable to other ALC+amp combinations.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20240802152215.20831-4-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A patch from Richard Fitzgerald adding dummy versions of the ACPI lookup
functions for SPI:
Provide empty versions of acpi_spi_count_resources(),
acpi_spi_device_alloc() and acpi_spi_find_controller_by_adev()
if the real functions are not being built.
This commit fixes two problems with the original definitions:
1) There wasn't an empty version of these functions
2) The #if only depended on CONFIG_ACPI. But the functions are implemented
in the core spi.c so CONFIG_SPI_MASTER must also be enabled for the real
functions to exist.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmaxKmgACgkQJNaLcl1U
h9DoTwf9FnURHsbLDugoWZlGnqMJoBzseQYCv2F45BoOLzBgIjDHZ80DUq0hgwGa
Igxxk1oMbQtqVHZnnVRhpytpC8F2jAS6tJ68xeBDmWgRFwhcFKyVYk1VLjjmbfSW
0zyxBXE7tiKet4FQpIBNNkk91FTMqnK0YWN1LoArbihrZ2x5YcdnFHc8CjV9PKi3
Y/xTL2sKOqmMNda/7oLYOWDfNXb2Gs3YAoLF+ERT+R+GKT2MGXqrRxVGx+D6ijJb
vPIxJMHWafzR5y+ysvG9wxVqxudAErvewpwP6KQmhPvhdqDolgoYwsFItdRc30Gf
g6xh5rzCFsEsjvII0rdutGzAdIfAJw==
=GsTT
-----END PGP SIGNATURE-----
Merge tag 'spi-acpi-lookup-dummy' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into topic/cirrus-hp-g12
spi: Add empty versions of ACPI lookup functions
A patch from Richard Fitzgerald adding dummy versions of the ACPI lookup
functions for SPI:
Provide empty versions of acpi_spi_count_resources(),
acpi_spi_device_alloc() and acpi_spi_find_controller_by_adev()
if the real functions are not being built.
This commit fixes two problems with the original definitions:
1) There wasn't an empty version of these functions
2) The #if only depended on CONFIG_ACPI. But the functions are implemented
in the core spi.c so CONFIG_SPI_MASTER must also be enabled for the real
functions to exist.
Log the address of the register that caused the timeout
interrupt by reading RMTIMEOUTREG_CAPTURE
--v2:
- Update RMTIMEOUTREG_CAPTURE naming (Suraj)
--v3:
- XeLpdp naming convention.
- Use if condition instead of else if
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807142106.1270213-1-mitulkumar.ajitkumar.golani@intel.com
