The detection of IEEE 1394:1995 and Canon MV5i is just required within
some of the condition branches. In this case, these check can be
capsulated within these branches.
This commit refactors the checks.
Link: https://lore.kernel.org/r/20250908012108.514698-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The gap_count member of fw_card structure is referred when initiate bus
reset. This reference is done out of acquiring lock. This is not good.
This commit takes the reference within the acquiring lock, with
additional code refactoring.
Link: https://lore.kernel.org/r/20250908012108.514698-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The call of bm_work should be done after acquiring spin lock of fw_card.
For asynchronous transaction, the lock should be released temporarily
due to event waiting.
A commit 27310d5616 ("firewire: core: use guard macro to maintain
properties of fw_card") applied scoped_guard() to the bm_work function,
however it looks hard to follow to the control flow.
This commit refactors the spin lock acquisition after the transaction.
Link: https://lore.kernel.org/r/20250908012108.514698-8-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The function local variable, transaction_data, in bm_work function is
conditionally used. In the case, the branch-level variable is sometimes
useful.
This commit uses this idea.
Link: https://lore.kernel.org/r/20250908012108.514698-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
In "bm_work" function, the references to fw_card and fw_node are
released at last. This is achieved by using goto statements. For this
case, the kernel cleanup framework is available.
This commit uses the framework to remove these statements.
Link: https://lore.kernel.org/r/20250908012108.514698-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The data mbmer in fw_node structure is an opaque pointer, while nowadays
it is just used to refer to fw_device associated with the fw_node.
This commit redefines the opaque pointer to a pointer to fw_device
structure, and adds some helper functions to set/get it.
Link: https://lore.kernel.org/r/20250908012108.514698-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The helper macro, retain_and_null_ptr(), introduced by a commit
092d00ead7 ("cleanup: Provide retain_and_null_ptr()") in v6.16 kernel,
is useful in the error path to release the part of structure member.
This commit uses the relatively new function.
Link: https://lore.kernel.org/r/20250908012108.514698-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
When allocating the list of isochronous context structure, a kzalloc()
variant of managed device API is used. In this case, a kcalloc() variant
is available.
This commit replaces these lines with devm_kcalloc().
Link: https://lore.kernel.org/r/20250908012108.514698-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Add support for MPS VR mp2869/mp2869a,mp29608/mp29608a,mp29612/mp29612a
and mp29816/mp29816a/mp29816b/mp29816c controller. This driver exposes
telemetry and limit value readings and writtings.
Signed-off-by: Wensheng Wang <wenswang@yeah.net>
Link: https://lore.kernel.org/r/20250805102020.749850-2-wenswang@yeah.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for MPS mp2869/mp2869a,mp29608/mp29608a,mp29612/mp29612a,
mp29816/mp29816a/mp29816b/mp29816c and mp29502 controller.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Wensheng Wang <wenswang@yeah.net>
Link: https://lore.kernel.org/r/20250805102020.749850-1-wenswang@yeah.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_mutex_init() instead of hand-writing it.
This saves some LoC, improves readability and saves some space in the
generated .o file.
Before:
======
text data bss dec hex filename
25878 11329 128 37335 91d7 drivers/hwmon/nzxt-smart2.o
After:
=====
text data bss dec hex filename
25551 11257 128 36936 9048 drivers/hwmon/nzxt-smart2.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f51fac0871ec7dbe4e28447ee4f774d028a53426.1757240403.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA700 is register compatible to INA780 but has different current, power,
and energy LSB values.
While the chip does not directly report the shunt voltage, report
it anyway by calculating its value from the current register.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Cc: Christian Kahr <christian.kahr@sie.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a compatible string for INA700. The chip is register compatible with
INA780 but implements different ADC ranges and thus needs a separate
compatible entry.
Cc: Christian Kahr <christian.kahr@sie.at>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA780 is similar to the other chips in the series, but does not
support the shunt voltage register. Shunt voltage limit registers
have been renamed to current limit registers, but are otherwise
identical.
While the chip does not directly report the shunt voltage, report
it anyway by calculating its value from the current register.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Prepare for supporting chips with internal shunt resistor by only setting
calibration and shunt resistor registers if no current LSB is configured.
Do not display a log message during probe if a chip does not have shunt
and gain registers since those would otherwise display 0, and a message
just indicating that the driver was loaded would be just noise.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by this driver support configurable active-high
alert priority. This is already documented in the devicetree description.
Add support for it to the driver.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the energy64 attribute type instead of locally defined sysfs attributes
to report the accumulated energy.
No functional change intended.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Order chip type enum and chip configuration data alphabetically
to simplify adding support for additional chips.
No functional change.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the shunt voltage register and the current register now report the
same values, use the shunt voltage limit registers to report and adjust
current limits, using the same LSB as the LSB used for the actual current
register.
Handle current register accuracy differences in separate function to
improve code readability.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the value of the current register and the value of the shunt register
now match each other, it is no longer necessary to read the shunt voltage
register in the first place. Read the current register instead and use it
to calculate the shunt voltage.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The best possible dynamic range for current measurements is achieved
if the shunt register value matches the current register value. Adjust
the calibration register as well as fixed and default shunt resistor
values accordingly to achieve this range.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calculate voltage LSB values in the probe function and use throughout
the code.
Use a single function to read all voltages, independently of the register
width. Use the pre-calculated LSB values to convert register values to
voltages and do not rely on runtime chip specific code.
Use ROUND_CLOSEST functions instead of divide operations to reduce
rounding errors.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current, power, and energy LSB do not change during runtime, so we can
pre-calculate the respective values. The power LSB can be derived from
the current LSB using the equation in the datasheets. Similar, the
energy LSB can be derived from the power LSB.
Also add support for chips with built-in shunt resistor by providing
a chip specific configuration parameter for the current LSB. The
relationship of current -> power -> energy LSB values in those chips
is the same as in chips with external shunt resistor, so configuration
parameters for power and energy LSB are not needed.
Use ROUND_CLOSEST functions instead of divide operations to reduce
rounding errors.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature register is 16 bit wide for all chips. The decimal point
is at the same location (bit 7 = 1 degree C). That means we can use the
resolution to calculate temperatures. Do that to simplify the code.
There is only a single writeable temperature attribute, and it is very
unlikely that the chips supported by this driver will ever require another
one. That means checking for that attribute in the write function is
unnecessary. Drop the check. Rename the write function from
ina238_write_temp() to ina238_write_temp_max() to reflect that a single
attribute is written.
Also extend the accepted temperature value range to the range supported by
the chip registers. Limiting the accepted value range to the temperature
range supported by the chip would make it impossible to read an
out-of-range limit from the chip and to write the same value back into it.
This is undesirable, especially since the maximum temperature register does
contain the maximum register value after a chip reset, not the temperature
limit supported by the chip.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is only a single writeable power attribute, and it is very unlikely
that the chips supported by this driver will ever require another one.
That means checking for that attribute during runtime is unnecessary.
Drop the check. Rename the write function from ina238_write_power() to
ina238_write_power_max() to reflect that a single attribute is written.
No functional change intended.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update driver documentation and Kconfig entry to list all chips supported
by the driver.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are no in-tree users of ina2xx platform data. Drop
support for it. The driver already supports device properties
which can be used as alternative if needed.
Also remove reference to the non-existing shunt_resistor sysfs
attribute from the driver documentation.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many chips require 64-bit variables to display the accumulated energy,
even more so since the energy units are micro-Joule. Add new sensor type
"energy64" to support reporting the chip energy as 64-bit values.
Changing the entire hardware monitoring API is not feasible, and it is only
really necessary to support reading 64-bit values for the "energyX_input"
attribute. For this reason, keep the API as-is and use type casts on both
ends to pass 64-bit pointers when reading the accumulated energy. On the
write side (which is only useful for the energyX_enable attribute), keep
passing the written value as long.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # INA780
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add fan-shutdown-percent property, used to describe fan RPM in percent set
during shutdown. This is used to keep the fan running at fixed RPM after
the kernel shut down, which is useful on hardware that does keep heating
itself even after the kernel did shut down, for example from some sort of
management core. The current behavior of pwm-fan is to unconditionally
stop the fan on shutdown, which is not always the safe and correct thing
to do, so let the hardware description include the expected behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250904202157.170600-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document fan-shutdown-percent property, used to describe fan RPM in percent
set during shutdown. This is used to keep the fan running at fixed RPM after
the kernel shut down, which is useful on hardware that does keep heating
itself even after the kernel did shut down, for example from some sort of
management core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250904202157.170600-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sort all the declarations in the source file. Contributors are asked
to insert new entries keeping alphabetical order, but the existing
ones were not completely sorted.
Signed-off-by: Michael Tandy <git@mjt.me.uk>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20250903184753.5876-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ti,maximum-expected-current-microamp, ti,shunt-gain, and shunt-resistor
properties are not supported on all chips described in this bindings file.
Update the bindings accordingly.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250901155902.2667063-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for label sysfs attribute similar to other hwmon devices.
This is particularly useful for systems with multiple sensors on the
same board, where identifying individual sensors is much easier since
labels can be defined via device tree.
Signed-off-by: Flaviu Nistor <flaviu.nistor@gmail.com>
Link: https://lore.kernel.org/r/20250825180248.1943607-2-flaviu.nistor@gmail.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for an optional label property similar to other hwmon devices.
This allows, in case of boards with multiple TMP102 sensors, to assign
distinct names to each instance.
Signed-off-by: Flaviu Nistor <flaviu.nistor@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250825180248.1943607-1-flaviu.nistor@gmail.com
[groeck: Dropped unnecessary "|" after "description:"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove outdated mention of the supported mmotherboard families and add a
hint which sensor readings are available via the module.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20250830131224.748481-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change the 'ret' variable from u32 to int in nct6775_asuswmi_read() to
store negative error codes or zero;
Storing the negative error codes in unsigned type, doesn't cause an issue
at runtime but can be confusing. Additionally, assigning negative error
codes to unsigned type may trigger a GCC warning when the -Wsign-conversion
flag is enabled.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://lore.kernel.org/r/20250830095105.3271-1-rongqianfeng@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intel CPUs have been using Family 6 for a while. The Family-model checks
in the coretemp driver implicitly assume Family 6. With the upcoming
Family 18 and 19 models, some of these checks fall apart.
While reading the temperature target MSR, cpu_has_tjmax() performs model
checks only to determine if a device warning should be printed. Instead
of expanding the checks, get rid of the function and print the warning
once unconditionally if the MSR read fails. The checks aren't worth
preventing a single line warning to dmesg.
Update the rest of the x86_model checks with VFM ones to make them more
robust. This automatically covers the upcoming Family 18 and 19 as well
as any future extended families.
Add a code comment to reflect that none of the CPUs in Family 5 or
Family 15 set X86_FEATURE_DTHERM. The VFM checks do not impact these
CPUs since the driver does not load on them.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Sohil Mehta <sohil.mehta@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20250828201729.1145420-1-sohil.mehta@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many AMD CPUs can support this feature now. We would get a wrong CPU DIE
temperature if don't consider this. In low-temperature environments,
the CPU die temperature can drop below zero. So many platforms would like
to make extended temperature range as their default configuration.
Default temperature range (0C to 255.875C).
Extended temperature range (-49C to +206.875C).
Ref Doc: AMD V3000 PPR (Doc ID #56558).
Signed-off-by: Chuande Chen <chuachen@cisco.com>
Link: https://lore.kernel.org/r/20250814053940.96764-1-chenchuande@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This fixes differences for the P8 system that was initially set to
the same thermal values as the P7, also adds in the PSU sensor for
all of the supported systems
Signed-off-by: David Ober <dober@lenovo.com>
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20250807103228.10465-1-dober6023@gmail.com
[groeck: Update subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
