Add initial support for Renesas Ethernet-TSN End-station device of R-Car
V4H. The Ethernet End-station can connect to an Ethernet network using a
10 Mbps, 100 Mbps, or 1 Gbps full-duplex link via MII/GMII/RMII/RGMII.
Depending on the connected PHY.
The driver supports Rx checksum and offload and hardware timestamps.
While full power management and suspend/resume is not yet supported the
driver enables runtime PM in order to enable the module clock. While
explicit clock management using clk_enable() would suffice for the
supported SoC, the module could be reused on SoCs where the module is
part of a power domain.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schiffer says:
====================
net: dsa: qca8k: cleanup and port isolation
A small cleanup patch, and basically the same changes that were just
accepted for mt7530 to implement port isolation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a pair of ports from the port matrix when both ports have the
isolated flag set.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the logic in qca8k_port_bridge_join() and qca8k_port_bridge_leave()
is the same. Refactor to reduce duplication and prepare for reusing the
code for implementing bridge port isolation.
dsa_port_offloads_bridge_dev() is used instead of
dsa_port_offloads_bridge(), passing the bridge in as a struct netdevice *,
as we won't have a struct dsa_bridge in qca8k_port_bridge_flags().
The error handling is changed slightly in the bridge leave case,
returning early and emitting an error message when a regmap access fails.
This shouldn't matter in practice, as there isn't much we can do if
communication with the switch breaks down in the middle of reconfiguration.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_port_bridge_join() set QCA8K_PORT_LOOKUP_CTRL() for i == port twice,
once in the loop handling all other port's masks, and finally at the end
with the accumulated port_mask.
The first time it would incorrectly set the port's own bit in the mask,
only to correct the mistake a moment later. qca8k_port_bridge_leave() had
the same issue, but here the regmap_clear_bits() was a no-op rather than
setting an unintended value.
Remove the duplicate assignment by skipping the whole loop iteration for
i == port. The unintended bit setting doesn't seem to have any negative
effects (even when not reverted right away), so the change is submitted
as a simple cleanup rather than a fix.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herve Codina says:
====================
Handle switch reset in mscc-miim
These two patches were previously sent as part of a bigger series:
https://lore.kernel.org/lkml/20240527161450.326615-1-herve.codina@bootlin.com/
v1 and v2 iterations were handled during the v1 and v2 reviews of this
bigger series. As theses two patches are now ready to be applied, they
were extracted from the bigger series and sent alone in this current
series.
This current v3 series takes into account feedback received during the
bigger series v2 review.
Changes v2 -> v3
- patch 1
Drop one useless sentence.
Add 'Reviewed-by: Andrew Lunn <andrew@lunn.ch>'
Add 'Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>'
- patch 2
Add 'Reviewed-by: Andrew Lunn <andrew@lunn.ch>'
Changes v1 -> v2 (as part of the bigger series iterations)
- Patch 1
Improve the reset property description
- Patch 2
Fix a wrong reverse x-mass tree declaration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mscc-miim device can be impacted by the switch reset, at least when
this device is part of the LAN966x PCI device.
Handle this newly added (optional) resets property.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the (optional) resets property.
The mscc-miim device is impacted by the switch reset especially when the
mscc-miim device is used as part of the LAN966x PCI device.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 27bd5fdc24 ("KVM: SEV-ES: Prevent MSR access post VMSA
encryption"), older VMMs like QEMU 9.0 and older will fail when booting
SEV-ES guests with something like the following error:
qemu-system-x86_64: error: failed to get MSR 0x174
qemu-system-x86_64: ../qemu.git/target/i386/kvm/kvm.c:3950: kvm_get_msrs: Assertion `ret == cpu->kvm_msr_buf->nmsrs' failed.
This is because older VMMs that might still call
svm_get_msr()/svm_set_msr() for SEV-ES guests after guest boot even if
those interfaces were essentially just noops because of the vCPU state
being encrypted and stored separately in the VMSA. Now those VMMs will
get an -EINVAL and generally crash.
Newer VMMs that are aware of KVM_SEV_INIT2 however are already aware of
the stricter limitations of what vCPU state can be sync'd during
guest run-time, so newer QEMU for instance will work both for legacy
KVM_SEV_ES_INIT interface as well as KVM_SEV_INIT2.
So when using KVM_SEV_INIT2 it's okay to assume userspace can deal with
-EINVAL, whereas for legacy KVM_SEV_ES_INIT the kernel might be dealing
with either an older VMM and so it needs to assume that returning
-EINVAL might break the VMM.
Address this by only returning -EINVAL if the guest was started with
KVM_SEV_INIT2. Otherwise, just silently return.
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Nikunj A Dadhania <nikunj@amd.com>
Reported-by: Srikanth Aithal <sraithal@amd.com>
Closes: https://lore.kernel.org/lkml/37usuu4yu4ok7be2hqexhmcyopluuiqj3k266z4gajc2rcj4yo@eujb23qc3zcm/
Fixes: 27bd5fdc24 ("KVM: SEV-ES: Prevent MSR access post VMSA encryption")
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240604233510.764949-1-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new trigger which turns LEDs on when there is input
(/dev/input/event*) activity and turns them back off again after there has
been no activity for 5 seconds.
This is primarily intended to control LED devices which are a backlight for
capacitive touch-buttons, such as e.g. the menu / home / back buttons found
on the bottom bezel of many somewhat older smartphones and tablets.
This can also be used to turn on the keyboard backlight LED on input
events and turn the keyboard backlight off again when idle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240531135910.168965-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
ich7_lpc_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The error handling code assumes incorrectly it's a normal errno
and checks for < 0. The return code is returned from the probe function
as is but probe functions should return normal errnos.
Remove < 0 from the check and convert PCIBIOS_* returns code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: a328e95b82 ("leds: LED driver for Intel NAS SS4200 series (v5)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132700.14260-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Fix the 'make W=1" issue:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/blink/leds-bcm63138.o
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240517-md-leds-bcm63138-v1-1-247b7302edb6@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
Fix the 'make W=1' issues:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/simple/simatic-ipc-leds-gpio-apollolake.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/simple/simatic-ipc-leds-gpio-core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/simple/simatic-ipc-leds-gpio-elkhartlake.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/simple/simatic-ipc-leds-gpio-f7188x.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/leds/simple/simatic-ipc-leds.o
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240517-md-simatic-ipc-v1-1-bbbd199262b8@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240522165358.62238-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
Some triggers call led_trigger_event() from their activate() callback
to initialize the brightness of the LED for which the trigger is being
activated.
In order for the LED's initial state to be set correctly this requires that
the led_trigger_event() call uses the new version of trigger->led_cdevs,
which has the new LED.
AFAICT led_trigger_event() will always use the new version when it is
running on the same CPU as where the list_add_tail_rcu() call was made,
which is why the missing synchronize_rcu() has not lead to bug reports.
But if activate() is pre-empted, sleeps or uses a worker then
the led_trigger_event() call may run on another CPU which may still use
the old trigger->led_cdevs list.
Add a synchronize_rcu() call to ensure that any led_trigger_event() calls
done from activate() always use the new list.
Triggers using led_trigger_event() from their activate() callback are:
net/bluetooth/leds.c, net/rfkill/core.c and drivers/tty/vt/keyboard.c.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240531120124.75662-1-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Triggers which have trigger specific sysfs attributes typically store
related data in trigger-data allocated by the activate() callback and
freed by the deactivate() callback.
Calling device_remove_groups() after calling deactivate() leaves a window
where the sysfs attributes show/store functions could be called after
deactivation and then operate on the just freed trigger-data.
Move the device_remove_groups() call to before deactivate() to close
this race window.
This also makes the deactivation path properly do things in reverse order
of the activation path which calls the activate() callback before calling
device_add_groups().
Fixes: a7e7a31563 ("leds: triggers: add device attribute support")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240504162533.76780-1-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
'is31fl3190_regmap_config' and 'is31fl3196_regmap_config' are not modified
in this diver and are only used as a const struct regmap_config.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
text data bss dec hex filename
13827 2002 32 15861 3df5 drivers/leds/leds-is31fl319x.o
After:
text data bss dec hex filename
14467 1370 32 15869 3dfd drivers/leds/leds-is31fl319x.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/82a5cb26ff8af1865a790286bdbc3c4a2bd149f1.1714892598.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
Merge ACPI device enumeration fixes for 6.10-rc5:
- Ignore MIPI camera graph port nodes created with the help of the
information from the ACPI tables on all Dell Tiger, Alder and Raptor
Lake models as that information is reported to be invalid on the
systems in question (Hans de Goede).
- Use new Intel CPU model matching macros in the MIPI DisCo for Imaging
part of ACPI device enumeration (Hans de Goede).
* acpi-scan:
ACPI: mipi-disco-img: Switch to new Intel CPU model defines
ACPI: scan: Ignore camera graph port nodes on all Dell Tiger, Alder and Raptor Lake models
The ChromeOS Embedded Controller exposes an LED control command.
Expose its functionality through the leds subsystem.
The LEDs are exposed as multicolor devices.
A hardware trigger, which is active by default, is provided to let the
EC itself take over control over the LED.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240613-cros_ec-led-v3-4-500b50f41e0f@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
led_get_color_name() is a safer alternative to led_colors.
led-class-multicolor.c is the only external user of led_colors and its
removal allows unexporting the array.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240613-cros_ec-led-v3-2-500b50f41e0f@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
This is similar to the existing led_colors[] array but is safer to use and
usable by everyone.
Getting string representations of color ids is useful for drivers
which are handling color IDs anyways, for example for the multicolor API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240613-cros_ec-led-v3-1-500b50f41e0f@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
James Chapman says:
====================
l2tp: don't use the tunnel socket's sk_user_data in datapath
This series refactors l2tp to not use the tunnel socket's sk_user_data
in the datapath. The main reasons for doing this are
* to allow for simplifying internal socket cleanup code (to be done
in a later series)
* to support multiple L2TPv3 UDP tunnels using the same 5-tuple
address
When handling received UDP frames, l2tp's current approach is to look
up a session in a per-tunnel list. l2tp uses the tunnel socket's
sk_user_data to derive the tunnel context from the receiving socket.
But this results in the socket and tunnel lifetimes being very tightly
coupled and the tunnel/socket cleanup paths being complicated. The
latter has historically been a source of l2tp bugs and makes the code
more difficult to maintain. Also, if sockets are aliased, we can't
trust that the socket's sk_user_data references the right tunnel
anyway. Hence the desire to not use sk_user_data in the datapath.
The new approach is to lookup sessions in a per-net session list
without first deriving the tunnel:
* For L2TPv2, the l2tp header has separate tunnel ID and session ID
fields which can be trivially combined to make a unique 32-bit key
for per-net session lookup.
* For L2TPv3, there is no tunnel ID in the packet header, only a
session ID, which should be unique over all tunnels so can be used
as a key for per-net session lookup. However, this only works when
the L2TPv3 session ID really is unique over all tunnels. At least
one L2TPv3 application is known to use the same session ID in
different L2TPv3 UDP tunnels, relying on UDP address/ports to
distinguish them. This worked previously because sessions in UDP
tunnels were kept in a per-tunnel list. To retain support for this,
L2TPv3 session ID collisions are managed using a separate per-net
session hlist, keyed by ID and sk. When looking up a session by ID,
if there's more than one match, sk is used to find the right one.
L2TPv3 sessions in IP-encap tunnels are already looked up by session
ID in a per-net list. This work has UDP sessions also use the per-net
session list, while allowing for session ID collisions. The existing
per-tunnel hlist becomes a plain list since it is used only in
management and cleanup paths to walk a list of sessions in a given
tunnel.
For better performance, the per-net session lists use IDR. Separate
IDRs are used for L2TPv2 and L2TPv3 sessions to avoid potential key
collisions.
These changes pass l2tp regression tests and improve data forwarding
performance by about 10% in some of my test setups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-tunnel session list is no longer used by the
datapath. However, we still need a list of sessions in the tunnel for
l2tp_session_get_nth, which is used by management code. (An
alternative might be to walk each session IDR list, matching only
sessions of a given tunnel.)
Replace the per-tunnel hlist with a per-tunnel list. In functions
which walk a list of sessions of a tunnel, walk this list instead.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of l2tp_tunnel_get_session are now gone so it can be
removed.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic session getter which uses IDR. Replace all users of
l2tp_tunnel_get_session which uses the per-tunnel session list to use
the generic getter.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If UDP sockets are aliased, sk might be the wrong socket. There's no
benefit to using sk_user_data to do some checks on the associated
tunnel context. Just report the error anyway, like udp core does.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify UDP decap to not use the tunnel pointer which comes from the
sock's sk_user_data when parsing the L2TP header. By looking up the
destination session using only the packet contents we avoid potential
UDP 5-tuple aliasing issues which arise from depending on the socket
that received the packet.
Drop the useless error messages on short packet or on failing to find
a session since the tunnel pointer might point to a different tunnel
if multiple sockets use the same 5-tuple.
Short packets (those not big enough to contain an L2TP header) are no
longer counted in the tunnel's invalid counter because we can't derive
the tunnel until we parse the l2tp header to lookup the session.
l2tp_udp_encap_recv was a small wrapper around l2tp_udp_recv_core which
used sk_user_data to derive a tunnel pointer in an RCU-safe way. But
we no longer need the tunnel pointer, so remove that code and combine
the two functions.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2TPv2 sessions are currently kept in a per-tunnel hashlist, keyed by
16-bit session_id. When handling received L2TPv2 packets, we need to
first derive the tunnel using the 16-bit tunnel_id or sock, then
lookup the session in a per-tunnel hlist using the 16-bit session_id.
We want to avoid using sk_user_data in the datapath and double lookups
on every packet. So instead, use a per-net IDR to hold L2TPv2
sessions, keyed by a 32-bit value derived from the 16-bit tunnel_id
and session_id. This will allow the L2TPv2 UDP receive datapath to
lookup a session with a single lookup without deriving the tunnel
first.
L2TPv2 sessions are held in their own IDR to avoid potential
key collisions with L2TPv3 sessions.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2TPv3 sessions are currently held in one of two fixed-size hash
lists: either a per-net hashlist (IP-encap), or a per-tunnel hashlist
(UDP-encap), keyed by the L2TPv3 32-bit session_id.
In order to lookup L2TPv3 sessions in UDP-encap tunnels efficiently
without finding the tunnel first via sk_user_data, UDP sessions are
now kept in a per-net session list, keyed by session ID. Convert the
existing per-net hashlist to use an IDR for better performance when
there are many sessions and have L2TPv3 UDP sessions use the same IDR.
Although the L2TPv3 RFC states that the session ID alone identifies
the session, our implementation has allowed the same session ID to be
used in different L2TP UDP tunnels. To retain support for this, a new
per-net session hashtable is used, keyed by the sock and session
ID. If on creating a new session, a session already exists with that
ID in the IDR, the colliding sessions are added to the new hashtable
and the existing IDR entry is flagged. When looking up sessions, the
approach is to first check the IDR and if no unflagged match is found,
check the new hashtable. The sock is made available to session getters
where session ID collisions are to be considered. In this way, the new
hashtable is used only for session ID collisions so can be kept small.
For managing session removal, we need a list of colliding sessions
matching a given ID in order to update or remove the IDR entry of the
ID. This is necessary to detect session ID collisions when future
sessions are created. The list head is allocated on first collision
of a given ID and refcounted.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an unused variable in struct l2tp_tunnel which was left behind
by commit c4d48a58f3 ("l2tp: convert l2tp_tunnel_list to idr").
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting FW_UPLOAD is not sufficient as it allows the firmware loader
API to be built as a module alongside the pd692x0 driver built as builtin.
Add select FW_LOADER to fix this issue.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406200632.hSChnX0g-lkp@intel.com/
Fixes: 9a99384518 ("net: pse-pd: Add PD692x0 PSE controller driver")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing method of reserving unicast filter count leads to wasted
MCAM entries if the functionality is not used or fewer entries are used.
Furthermore, the amount of MCAM entries differs amongst Octeon SoCs.
We implemented a means to adjust the UC filter count via devlink,
allowing for better use of MCAM entries across Netdev apps.
commands:
To get the current unicast filter count
# devlink dev param show pci/0002:02:00.0 name unicast_filter_count
To change/set the unicast filter count
# devlink dev param set pci/0002:02:00.0 name unicast_filter_count
value 5 cmode runtime
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __ethtool_get_ts_info function returns directly if the device has a
get_ts_info() method. For bonding with an active slave, this works correctly
as we simply return the real device's timestamping information. However,
when there is no active slave, we only check the slave's TX software
timestamp information. We still need to set the phc index and RX timestamp
information manually. Otherwise, the result will be look like:
Time stamping parameters for bond0:
Capabilities:
software-transmit
PTP Hardware Clock: 0
Hardware Transmit Timestamp Modes: none
Hardware Receive Filter Modes: none
This issue does not affect VLAN or MACVLAN devices, as they only have one
downlink and can directly use the downlink's timestamping information.
Fixes: b8768dc407 ("net: ethtool: Refactor identical get_ts_info implementations.")
Reported-by: Liang Li <liali@redhat.com>
Closes: https://issues.redhat.com/browse/RHEL-42409
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
- New device_prep_peripheral_dma_vec, documentation and user
-----BEGIN PGP SIGNATURE-----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=xEOp
-----END PGP SIGNATURE-----
Merge tag 'dmaengine_topic_dma_vec' into next
Dmaengine topic
- New device_prep_peripheral_dma_vec, documentation and user
Document the dmaengine_prep_peripheral_dma_vec() API function, the
device_prep_peripheral_dma_vec() backend function, and the dma_vec
struct.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20240620122726.41232-8-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add implementation of the .device_prep_peripheral_dma_vec() callback.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240620122726.41232-3-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This function can be used to initiate a scatter-gather DMA transfer,
where the address and size of each segment is located in one entry of
the dma_vec array.
The major difference with dmaengine_prep_slave_sg() is that it supports
specifying the lengths of each DMA transfer; as trying to override the
length of the transfer with dmaengine_prep_slave_sg() is a very tedious
process. The introduction of a new API function is also justified by the
fact that scatterlists are on their way out.
Note that dmaengine_prep_interleaved_dma() is not helpful either in that
case, as it assumes that the address of each segment will be higher than
the one of the previous segment, which we just cannot guarantee in case
of a scatter-gather transfer.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240620122726.41232-2-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sdw_initialize_slave() function stores 'slave->prop' as local 'prop'
variable, so use it in all applicable places to make code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20240620091046.12426-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, we do port_bo += bps * ch in both inside and outside
sdw_compute_master_ports(). We can pass port_bo as a pointer and only
calculate port_bo in sdw_compute_master_ports().
Besides, different port could use different lanes and we can't just
add port_bo based on total channels in a manager.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240617121350.14074-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some reason a number of files included the "All rights reserved"
statement. Good old copy-paste made sure this mistake proliferated.
Remove the "All rights reserved" in all Intel-copyright to align with
internal guidance.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240617121318.14037-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
