Because mitigation episode duration is printed in milliseconds, there
is no reason to print timestamp information for mitigation episodes in
smaller units which also makes it somewhat harder to interpret the
numbers.
Print it in milliseconds for consistency.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Because thermal zone handling by the thermal core is started from
scratch during resume from system-wide suspend, prevent the debug
code from extending mitigation episodes beyond that point by ending
the mitigation episode currently in progress, if any, for each thermal
zone.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add a helper for updating trip point overstepping duration to be called
from thermal_debug_tz_trip_down().
Subsequently, it will also be used during resume from system-wide
suspend.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Consider a thermal zone with one passive trip point, a cooling device
with 3 states (0, 1, 2) bound to it, passive polling enabled (nonzero
passive_delay_jiffies) and no regular polling (polling_delay_jiffies
equal to 0) that is managed by the Step-Wise governor. Suppose that
the initial state of the cooling device is 0 and the zone temperature
is below the trip point to start with.
When the trip point is crossed, tz->passive is incremented by the
thermal core and the governor's .manage() callback is invoked. It
sets 'throttle' to 'true' for the trip in question and
get_target_state() returns 1 for the instance corresponding to the
cooling device (say that 'upper' and 'lower' are set to 2 and 0 for
it, respectively), so its state changes to 1.
Passive polling is still active for the zone, so next time the
temperature is updated, the governor's .manage() callback will be
invoked again. If the temperature is still rising, it will change
the state of the cooling device to 2.
Now suppose that next time the zone temperature is updated, it falls
below the trip point, so tz->passive is decremented for the zone (say
it becomes 0 then) and the governor's .manage() callbacks runs.
It finds that the temperature trend for the zone is 'falling' and
'throttle' will be set to 'false' for the trip in question, so the
cooling device's state will be changed to 1. However, because
tz->polling is 0 for the zone, the governor's .manage() callback
may not be invoked again for a long time and the cooling device's
state will not be reset back to 0.
This can happen because commit 042a3d80f1 ("thermal: core: Move
passive polling management to the core") removed passive polling
management from the Step-Wise governor.
Before that change, thermal_zone_trip_update() would bump up
tz->passive when changing the target state for a thermal instance
from "no target" to a specific value and it would drop tz->passive
when changing it back to "no target" which would cause passive
polling to be active for the zone until the governor has reset the
states of all cooling devices. In particular, in the example above
tz->passive would be incremented when changing the state of the
cooling device from 0 to 1 and then it would be still nonzero when
the state of the cooling device was changed from 2 to 1.
To prevent this problem from occurring, restore the passive polling
management in the Step-Wise governor by partially reverting the
commit in question and update the comment in the restored code
to explain its role more clearly.
Fixes: 042a3d80f1 ("thermal: core: Move passive polling management to the core")
Closes: https://lore.kernel.org/linux-pm/ZmVfcEOxmjUHZTSX@hovoldconsulting.com
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Whenever per pdev debugfs directory is created, a symlink to it is also
placed in ieee80211/phy* directory. During clean up of per pdev debugfs,
this symlink also needs to be cleaned up.
Add changes to clean up the symlink whenever the per pdev debugfs is
removed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-4-quic_adisi@quicinc.com
During normal de-initialization path or if any error happens while
registering the hardware, there is no support to unregister the per pdev
debugfs. Add support for the same.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-3-quic_adisi@quicinc.com
Function ath12k_debugfs_register() is called once inside the function
ath12k_mac_hw_register(). However, with single wiphy model, there could
be multiple pdevs registered under single hardware. Hence, need to register
debugfs for each one of them.
Move the caller inside the loop which iterates over all underlying pdevs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: f8bde02a26 ("wifi: ath12k: initial debugfs support")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-2-quic_adisi@quicinc.com
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in ath11k_install_key()
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set. And in ath11k_mac_mgmt_tx_wmi()
a length of IEEE80211_CCMP_MIC_LEN is reserved for all ciphers.
This results in unexpected management frame drop in case either of above 3 ciphers
is used. The reason is, without IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211
will not generate CCMP/GCMP headers in frame for ath11k. Also MIC length reserved
is wrong. Such frame is dropped later by hardware:
ath11k_pci 0000:5a:00.0: mac tx mgmt frame, buf id 0
ath11k_pci 0000:5a:00.0: mgmt tx compl ev pdev_id 1, desc_id 0, status 1
From user point of view, we have observed very low throughput due to this issue:
action frames are all dropped so ADDBA response from DUT never reaches AP. AP
can not use aggregation thus throughput is low.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag and by reserving proper
MIC length for those ciphers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Closes: https://lore.kernel.org/all/CADS+iDX5=JtJr0apAtAQ02WWBxgOFEv8G063vuGYwDTC8AVZaw@mail.gmail.com
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240605014826.22498-1-quic_bqiang@quicinc.com
Currently, in the Rx error processing handler, once an MSDU drop is
detected, the subsequent MSDUs get unintentionally dropped due to the
previous drop flag being retained across all MSDU processing, leading
to the discarding of valid MSDUs. To resolve this issue, the drop flag
should be reset to false before processing each descriptor.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240604062641.2956288-1-quic_periyasa@quicinc.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240603091541.8367-2-wsa+renesas@sang-engineering.com
According to the FF-A spec (Buffer states and ownership), after a
producer has written into a buffer, it is "full" and now owned by the
consumer. The producer won't be able to use that buffer, until the
consumer hands it over with an invocation such as RX_RELEASE.
It is clear in the following paragraph (Transfer of buffer ownership),
that MEM_RETRIEVE_RESP is transferring the ownership from producer (in
our case SPM) to consumer (hypervisor). RX_RELEASE is therefore
mandatory here.
It is less clear though what is happening with MEM_FRAG_TX. But this
invocation, as a response to MEM_FRAG_RX writes into the same hypervisor
RX buffer (see paragraph "Transmission of transaction descriptor in
fragments"). Also this is matching the TF-A implementation where the RX
buffer is marked "full" during a MEM_FRAG_RX.
Release the RX hypervisor buffer in those two cases. This will unblock
later invocations using this buffer which would otherwise fail.
(RETRIEVE_REQ, MEM_FRAG_RX and PARTITION_INFO_GET).
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240611175317.1220842-1-vdonnefort@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
When CONFIG_NETKIT=y,
bpftool-cgroup shows error even if the cgroup's path is correct:
$ bpftool cgroup tree /sys/fs/cgroup
CgroupPath
ID AttachType AttachFlags Name
Error: can't query bpf programs attached to /sys/fs/cgroup: No such device or address
>From strace and kernel tracing, I found netkit returned ENXIO and this command failed.
I think this AttachType(BPF_NETKIT_PRIMARY) is not relevant to cgroup.
bpftool-cgroup should query just only cgroup-related attach types.
v2->v3:
- removed an unnecessary check
v1->v2:
- used an array of cgroup attach types
Signed-off-by: Kenta Tada <tadakentaso@gmail.com>
Reviewed-by: Quentin Monnet <qmo@kernel.org>
Link: https://lore.kernel.org/r/20240607111704.6716-1-tadakentaso@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Current documentation on RCU in ath11k_mac_op_ipv6_changed() says:
/* Note: read_lock_bh() calls rcu_read_lock() */
read_lock_bh(&idev->lock);
This is wrong because without enabling CONFIG_PREEMPT_RT
rcu_read_lock() is not called by read_lock_bh(). The reason
why current code works even in a CONFIG_PREEMPT_RT=n kernel
is because atomic_notifier_call_chain() already does that for
us, see:
int atomic_notifier_call_chain()
{
...
rcu_read_lock();
ret = notifier_call_chain(&nh->head, val, v, -1, NULL);
rcu_read_unlock();
...
}
and backtrace:
ath11k_mac_op_ipv6_changed
ieee80211_ifa6_changed
notifier_call_chain
atomic_notifier_call_chain
So update the comment to make it correct.
This is found during code review, compile tested only.
Fixes: feafe59c89 ("wifi: ath11k: use RCU when accessing struct inet6_dev::ac_list")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531022411.6543-1-quic_bqiang@quicinc.com
Currently ACPI notification handler is installed when driver loads and only
gets removed when driver unloads. During resume after firmware is reloaded,
ath12k tries to install it by default. Since it is installed already, ACPI
subsystem rejects it and returns an error:
[ 83.094206] ath12k_pci 0000:03:00.0: failed to install DSM notify callback: 7
Fix it by removing that handler when going to suspend. This also avoid any
possible ACPI call to firmware before firmware is reloaded/reinitialized.
Note ab->acpi also needs to be cleared in ath12k_acpi_stop() such that we
are in a clean state when ACPI structures are reinitialized in
ath12k_acpi_start().
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 576771c9fa ("wifi: ath12k: ACPI TAS support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531024000.9291-1-quic_bqiang@quicinc.com
When multiple radios are advertised as a single wiphy which supports various
bands, vdev creation for the vif is deferred until channel is assigned to it.
If a remain on channel (RoC) request is received from mac80211, select the
corresponding radio (ar) based on channel and create a vdev on that radio to
initiate an RoC scan.
Note that on RoC completion this vdev is not deleted. If a new RoC/hw scan
request is seen on that same vif for a different band the vdev will be deleted
and created on the new radio supporting the request.
Also if the RoC scan is requested when the vdev is in started state, no
switching to new radio is allowed and RoC request can be accepted only on
channels within same radio.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240528082739.1226758-1-quic_ramess@quicinc.com
Use the recently added DLM_LSFL_SOFTIRQ flag in dlm_new_lockspace(),
signalling the ability to handle callbacks being run from softirq
context. The md-cluster callback functions only call complete(),
which is suitable for softirq. This should make dlm lock request
completions more efficient by avoiding the workqueue context switch.
Acked-by: Heming Zhao <heming.zhao@suse.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
The calls write_lock/unlock_irq() disables and re-enables the IRQs.
Calling spin_lock_irqsave() and spin_lock_restore() when the IRQs are
already disabled doesn't do anything and just makes the code confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/8be473eb-65e0-42b4-b574-e61c3a7f62d8@moroto.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the issue where MEM_TO_MEM fail on i.MX8QM due to the requirement
that both source and destination addresses need pass through the IOMMU.
Typically, peripheral FIFO addresses bypass the IOMMU, necessitating
only one of the source or destination to go through it.
Set "is_remote" to true to ensure both source and destination
addresses pass through the IOMMU.
iMX8 Spec define "Local" and "Remote" bus as below.
Local bus: bypass IOMMU to directly access other peripheral register,
such as FIFO.
Remote bus: go through IOMMU to access system memory.
The test fail log as follow:
[ 66.268506] dmatest: dma0chan0-copy0: result #1: 'test timed out' with src_off=0x100 dst_off=0x80 len=0x3ec0 (0)
[ 66.278785] dmatest: dma0chan0-copy0: summary 1 tests, 1 failures 0.32 iops 4 KB/s (0)
Fixes: 72f5801a4e ("dmaengine: fsl-edma: integrate v3 support")
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240510030959.703663-1-joy.zou@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'reg_info' was never used since it's initial
commit 5d0c3533a1 ("dmaengine: qcom: Add GPI dma driver")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240517234024.231477-1-linux@treblig.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert binding doc from txt to yaml.
Re-order interrupt-names to align example.
Add #dma-cell in example.
Change 'reg' in example to 32bit address.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240528163734.2471268-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 'idle' in fsl_chan is redundant as it's equivalent to
'status != DMA_IN_PROGRESS'. So remote it to simple code logic.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240603152317.69917-2-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The edma feature individual IRQs for each DMA channel at some devices.
Given the presence of numerous eDMA instances, each with multiple channels,
IRQ request during probe results in an extensive list at /proc/interrupts.
However, a significant portion of these channels remains unused by the
system.
Request irq only when a DMA client driver requests a DMA channel.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240603152317.69917-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On STM32 DMA3, channels can be reserved, so they are non available for
Linux. This non-availability creates a mismatch between dma_chan id and
DMA3 channel id.
Use dma_async_device_channel_register() to register the channels
after controller registration and change the default channel name, so that
it can match the name in the Reference Manual and ease requesting a channel
thanks to its name.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-12-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Channel device name is used for sysfs, but also by dmatest filter function.
With dynamic channel registration, channels can be registered after dma
controller registration. Users may want to have specific channel names.
If name is NULL, the channel name relies on previous implementation,
dma<controller_device_id>chan<channel_device_id>.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-11-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement own device_tx_status ops to compute the residue with a finer
granularity, up to bytes.
STM32 DMA3 has a bitfield, BNDT, in CxTR1 register which reflects the
number of bytes read from the source.
It also has a bitfield, FIFOL, in CxSR register which reflects the FIFO
level in units of programmed destination data width.
The channel is briefly suspended to get a coherent snapshot of registers.
It is possible to correct the fifo level when packing/unpacking is enabled
with destination increment.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-10-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 DMA3 controller is able to suspend an ongoing transfer (the transfer
is suspended after the ongoing burst is flushed to the destination) and
resume it from the point it was suspended. No need to reconfigure any
register.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-9-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DMA_MEMCPY capability and relative device_prep_dma_memcpy ops with
stm32_dma3_prep_dma_memcpy(). It reuses stm32_dma3_chan_prep_hw() and
stm32_dma3_prep_hwdesc() helpers.
As this driver relies on both device_config and of_xlate ops to
pre-configure the channel for transfer, add a new helper
(stm32_dma3_init_chan_config_for_memcpy) in case the channel is used
without being pre-configured (with DT and/or dmaengine_slave_config()).
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-8-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 DMA3 driver supports the 3 hardware configurations of the STM32 DMA3
controller:
- LPDMA (Low Power): 4 channels, no FIFO
- GPDMA (General Purpose): 16 channels, FIFO from 8 to 32 bytes
- HPDMA (High Performance): 16 channels, FIFO from 8 to 256 bytes
Hardware configuration of the channels is retrieved from the hardware
configuration registers.
The client can specify its channel requirements through device tree.
STM32 DMA3 channels can be individually reserved either because they are
secure, or dedicated to another CPU.
Indeed, channels availability depends on Resource Isolation Framework
(RIF) configuration. RIF grants access to buses with Compartment ID (CID)
filtering, secure and privilege level. It also assigns DMA channels to one
or several processors.
DMA channels used by Linux should be CID-filtered and statically assigned
to CID1 or shared with other CPUs but using semaphore. In case CID
filtering is not configured, dma-channel-mask property can be used to
specify available DMA channels to the kernel, otherwise such channels
will be marked as reserved and can't be used by Linux.
STM32 DMA3 is a new STM32 DMA controller, not a new version of an existing
one.
stm32-dma is not considered for reuse because register layout is completely
different and doesn't rely on descriptors mechanism.
stm32-mdma is based on descriptors mechanism but there are significant
differences in register layout and descriptors structure.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The STM32 DMA3 is a Direct Memory Access controller with different features
depending on its hardware configuration.
The channels have not the same capabilities, some have a larger FIFO, so
their performance is higher.
This patch describes STM32 DMA3 bindings, used to select a channel that
fits client requirements, and to pre-configure the channel depending on
the client needs.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Gather the STM32 DMA controllers bindings under ./dma/stm32/.
Then fix reference to old path in spi/st,stm32-spi.yaml: update the dmas
property description by referring to all STM32 DMA controllers bindings.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20240531150712.2503554-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to using input_set_capability() instead of using __set_bit() to
make clear what exactly kinds of events (EV_KEY, EV_REL) are being
declared.
Also drop redundant calls setting EV_ABS and ABS_X|Y|Z bits as that is
taken care by input_set_abs_params().
Link: https://lore.kernel.org/r/20240610164301.1048482-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of creating driver-specific device attributes with
sysfs_create_group() have device core do this by setting up dev_groups
pointer in the driver structure.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20240610164301.1048482-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a lockspace user allows it, run callback functions directly from
softirq context, instead of queueing callbacks to be run from the
dlm_callback workqueue context.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
dma-channels is a number, not a list. Apply proper constraints on the
actual number.
Fixes: 6eb439dff6 ("dt-bindings: fsl-dma: fsl-edma: add edma3 compatible string")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240521083002.23262-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kbuild does not support having a source file compiled multiple times
and linked into distinct modules, or built-in and modular at the
same time. For fs-edma, there are two common components that are
linked into the fsl-edma.ko for Arm and PowerPC, plus the mcf-edma.ko
module on Coldfire. This violates the rule for compile-testing:
scripts/Makefile.build:236: drivers/dma/Makefile: fsl-edma-common.o is added to multiple modules: fsl-edma mcf-edma
scripts/Makefile.build:236: drivers/dma/Makefile: fsl-edma-trace.o is added to multiple modules: fsl-edma mcf-edma
I tried splitting out the common parts into a separate modules, but
that adds back the complexity that a cleanup patch removed, and it
gets harder with the addition of the tracepoints.
As a minimal workaround, address it at the Kconfig level, by disallowing
the broken configurations.
Link: https://lore.kernel.org/lkml/20240110232255.1099757-1-arnd@kernel.org/
Fixes: 66aac8ea0a ("dmaengine: fsl-edma: clean up EXPORT_SYMBOL_GPL in fsl-edma-common.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240528115440.2965975-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure we are disabling interrupts and destroying DMA pool if
pcie_capability_read/write_word() call failed.
Fixes: 511deae026 ("dmaengine: ioatdma: disable relaxed ordering for ioatdma")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240528-ioatdma-fixes-v2-2-a9f2fbe26ab1@yadro.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix leaking ioatdma_device if I/OAT version is less than IOAT_VER_3_0.
Fixes: bf453a0a18 ("dmaengine: ioat: Support in-use unbind")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240528-ioatdma-fixes-v2-1-a9f2fbe26ab1@yadro.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce a new external lockspace flag DLM_LSFL_SOFTIRQ_SAFE. A
lockspace user will set this flag if it can handle dlm running the
callback functions from softirq context. When not set, dlm will
continue to run callback functions from the dlm_callback workqueue.
The new lockspace flag cannot be used for user space lockspaces, so
a uapi placeholder definition is used for the new flag value.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
The existing external lockspace flag DLM_LSFL_FS is now also
saved as an internal flag LSFL_FS, so it can be checked from
other code locations which want to know if a lockspace is
used from the kernel or user space.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
The of_k3_udma_glue_parse_chn_by_id() helper function erroneously
invokes "of_node_put()" on the "udmax_np" device-node passed to it,
without having incremented its reference count at any point. Fix it.
Fixes: 81a1f90f20 ("dmaengine: ti: k3-udma-glue: Add function to parse channel by ID")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Peter Ujfalusi@gmail.com
Link: https://lore.kernel.org/r/20240602013319.2975894-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In imx_rproc_addr_init() "nph = of_count_phandle_with_args()" just counts
number of phandles. But phandles may be empty. So of_parse_phandle() in
the parsing loop (0 < a < nph) may return NULL which is later dereferenced.
Adjust this issue by adding NULL-return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a0ff4aa6f0 ("remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240606075204.12354-1-amishin@t-argos.ru
[Fixed title to fit within the prescribed 70-75 charcters]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
'ip6 dscp set $v' in an nftables outpute route chain has no effect.
While nftables does detect the dscp change and calls the reroute hook.
But ip6_route_me_harder never sets the dscp/flowlabel:
flowlabel/dsfield routing rules are ignored and no reroute takes place.
Thanks to Yi Chen for an excellent reproducer script that I used
to validate this change.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
