The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a statistical item to count the number of reset failures.
This statistical item can be queried using ethtool -S or
reported through diagnose information.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250723074826.2756135-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_reporter_rx_timeout() is currently invoked synchronously
in the driver's open error flow. This causes the thread holding
priv->state_lock to attempt acquiring the devlink lock, which
can result in a circular dependency with other devlink operations.
For example:
- Devlink health diagnose flow:
- __devlink_nl_pre_doit() acquires the devlink lock.
- devlink_nl_health_reporter_diagnose_doit() invokes the
driver's diagnose callback.
- mlx5e_rx_reporter_diagnose() then attempts to acquire
priv->state_lock.
- Driver open flow:
- mlx5e_open() acquires priv->state_lock.
- If an error occurs, devlink_health_reporter may be called,
attempting to acquire the devlink lock.
To prevent this circular locking scenario, defer the RX timeout
recovery by scheduling it via a workqueue. This ensures that the
recovery work acquires locks in a consistent order: first the
devlink lock, then priv->state_lock.
Additionally, make the recovery work acquire the netdev instance
lock to safely synchronize with the open/close channel flows,
similar to mlx5e_tx_timeout_work. Repeatedly attempt to acquire
the netdev instance lock until it is taken or the target RQ is no
longer active, as indicated by the MLX5E_STATE_CHANNELS_ACTIVE bit.
Fixes: 32c57fb268 ("net/mlx5e: Report and recover from rx timeout")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1753256672-337784-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When updating the PBMC register, we read its current value,
modify desired fields, then write it back.
The port_buffer_size field within PBMC is Read-Only (RO).
If this RO field contains a non-zero value when read,
attempting to write it back will cause the entire PBMC
register update to fail.
This commit ensures port_buffer_size is explicitly cleared
to zero after reading the PBMC register but before writing
back the modified value.
This allows updates to other fields in the PBMC register to succeed.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Yael Chemla <ychemla@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1753256672-337784-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check for ns < 0 is always false because variable ns is a u32 which
is not a signed type. Fix this by making ns a s32 type.
Fixes: cef9991e04 ("spi: Add Amlogic SPISG driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20250725171701.839927-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously arch_support_sort_key and arch_perf_header_entry used a
weak symbol to compile as appropriate for x86 and powerpc. A
limitation to this is that the handling of a data file could vary in
cross-platform development. Change to using the perf_env of the
current session to determine the architecture kind and set the sort
key and header entries as appropriate.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-23-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
test__x86_sample_parsing is identical to test__sample_parsing except
it explicitly tested PERF_SAMPLE_WEIGHT_STRUCT. Now the parsing code
is common move the PERF_SAMPLE_WEIGHT_STRUCT to the common sample
parsing test and remove the x86 version.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-22-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
By definition arch sample parsing and synthesis will inhibit certain
kinds of cross-platform record then analysis (report, script,
etc.). Remove arch_perf_parse_sample_weight and
arch_perf_synthesize_sample_weight replacing with a common
implementation. Combine perf_sample p_stage_cyc and retire_lat as
weight3 to capture the differing uses regardless of compiled for
architecture.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-21-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The global perf_env was used for the host, but if a perf_env wasn't
easy to come by it was used in a lot of places where potentially
recorded and host data could be confused. Remove the global variable
as now the majority of accesses retrieve the perf_env for the host
from the session.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-20-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
There is no session in perf trace unless in replay mode, so in host
mode no session can be associated with the evlist. If the evsel__env
call fails resort to the host_env that's part of the trace. Remove
errno_to_name as it becomes a called once 1-line function once the
argument is turned into a perf_env, just call perf_env__arch_strerrno
directly.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-19-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
auxtrace_mmap__read and auxtrace_mmap__read_snapshot end up calling
`evsel__env(NULL)` which returns the global perf_env variable for the
host. Their only call is in perf record. Rather than use the global
variable pass through the perf_env for `perf record`.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-18-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
When creating a machine for the host explicitly pass in a scoped
perf_env. This removes a use of the global perf_env.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-17-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The benchmark doesn't use a data file and so the header perf_env isn't
used. Stack allocate a host perf_env for use to avoid the use of the
global perf_env.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-16-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The use of the global host perf_env variable is potentially
inconsistent within the code. Switch perf top to using a locally
scoped variable that is generally accessed through the session.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-15-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
When creating a perf_session the host perf_env may or may not want to
be used. For example, `perf top` uses a host perf_env while `perf
inject` does not. Add a host_env argument to perf_session__new so that
sessions requiring a host perf_env can pass it in. Currently if none
is specified the global perf_env variable is used, but this will
change in later patches.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-14-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The perf_env global variable holds the host perf_env data but its use
is hit and miss. Switch to using local perf_env variables and ensure
scoped perf_env__init and perf_env__exit. This loses command line
setting of the perf_env, but this doesn't matter for tests. So the
perf_env is fully initialized, clear it with memset in perf_env__init.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-13-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Always use the perf_env from the feat_fd's perf_header. Cache the
value on entry to a function in `env` and use `env->` consistently in
the code. Ensure the header is initialized for use in
perf_session__do_write_header.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-12-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The session holds a perf_env pointer env. In UI code container_of is
used to turn the env to a session, but this assumes the session
header's env is in use. Rather than a dubious container_of, hold the
session in the evlist and derive the env from the session with
evsel__env, perf_session__env, etc.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-11-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The perf_env from the header in the session is frequently accessed,
add an accessor function rather than access directly. Cache the value
to avoid repeated calls. No behavioral change.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-10-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Support for build IDs in mmap2 perf events has been present since
Linux v5.12:
https://lore.kernel.org/lkml/20210219194619.1780437-1-acme@kernel.org/
Build ID mmap events don't avoid the need to inject build IDs for DSO
touched by samples as the build ID cache is populated by perf
record. They can avoid some cases of symbol mis-resolution caused by
the file system changing from when a sample occurred and when the DSO
is sought.
Unlike the --buildid-mmap option, this chnage doesn't disable the
build ID cache but it does disable the processing of samples looking
for DSOs to inject build IDs for. To disable the build ID cache the -B
(--no-buildid) option should be used.
Making this option the default was raised on the list in:
https://lore.kernel.org/linux-perf-users/CAP-5=fXP7jN_QrGUcd55_QH5J-Y-FCaJ6=NaHVtyx0oyNh8_-Q@mail.gmail.com/
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-9-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The DSO being generated was being accessed through a thread's maps,
this is unnecessary as the dso can just be directly found. This avoids
problems with passing a NULL evsel which may be inspected to determine
properties of a callchain when using the buildid DSO marking code.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-8-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The dso_id previously contained the major, minor, inode and inode
generation information from a mmap2 event - the inode generation would
be zero when reading from /proc/pid/maps. The build_id was in the
dso. With build ID mmap2 events these fields wouldn't be initialized
which would largely mean the special empty case where any dso would
match for equality. This isn't desirable as if a dso is replaced we
want the comparison to yield a difference.
To support detecting the difference between DSOs based on build_id,
move the build_id out of the DSO and into the dso_id. The dso_id is
also stored in the DSO so nothing is lost. Capture in the dso_id what
parts have been initialized and rename dso_id__inject to
dso_id__improve_id so that it is clear the dso_id is being improved
upon with additional information. With the build_id in the dso_id, use
memcmp to compare for equality.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-7-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
If a build ID is read then not all code paths may ensure it is empty
before use. Initialize the build_id to be zero-ed unless there is
clear initialization such as a call to build_id__init.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-6-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Previously only the sample IP's map DSO would be marked hit for the
purposes of populating the build ID cache. Walk the call chain to mark
all IPs and DSOs.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-5-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Pass in a size argument rather than implying all build id strings must
be SBUILD_ID_SIZE.
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250724163302.596743-4-irogers@google.com
[ fixed some build errors ]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Fix typos in comments and error messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250723201528.2908218-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'cxl' is missing from the path to the clear_poison attribute. Add it.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20250724224308.2101255-1-alison.schofield@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Although setup_ns() set net.ipv4.conf.default.rp_filter=0,
loading certain module such as ipip will automatically create a tunl0 interface
in all netns including new created ones. In the script, this is before than
default.rp_filter=0 applied, as a result tunl0.rp_filter remains set to 1
which causes the test report FAIL when ipip module is preloaded.
Before fix:
Testing DR mode...
Testing NAT mode...
Testing Tunnel mode...
ipvs.sh: FAIL
After fix:
Testing DR mode...
Testing NAT mode...
Testing Tunnel mode...
ipvs.sh: PASS
Fixes: 7c8b89ec50 ("selftests: netfilter: remove rp_filter configuration")
Signed-off-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Complain about kernel taint value only if it wasn't set at start
already.
Fixes: 73db1b5dab ("selftests: netfilter: Torture nftables netdev hooks")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The scratchmap size depends on the number of elements in the set.
For huge sets, each scratch map can easily require very large
allocations, e.g. for 100k entries each scratch map will require
close to 64kbyte of memory.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The matching algorithm has implemented thrice:
1. data path lookup, generic version
2. data path lookup, avx2 version
3. control plane lookup
Merge 1 and 3 by refactoring pipapo_get as a common helper, then make
nft_pipapo_lookup and nft_pipapo_get both call the common helper.
Aside from the code savings this has the benefit that we no longer allocate
temporary scratch maps for each control plane get and insertion operation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This stems from a time when sets and nft_dynset resided in different kernel
modules. We can replace this with a direct call.
We could even remove both ->update and ->delete, given its only
supported by rhashtable, but on the off-chance we'll see runtime
add/delete for other types or a new set type keep that as-is for now.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Return the extension pointer instead of passing it as a function
argument to be filled in by the callee.
As-is, whenever false is returned, the extension pointer is not used.
For all set types, when true is returned, the extension pointer was set
to the matching element.
Only exception: nft_set_bitmap doesn't support extensions.
Return a pointer to a static const empty element extension container.
return false -> return NULL
return true -> return the elements' extension pointer.
This saves one function argument.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
They are not used anymore, so remove them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce NFNL_HOOK_TYPE_NFT_FLOWTABLE to distinguish flowtable hooks
from base chain ones. Nested attributes are shared with the old NFTABLES
hook info type since they fit apart from their misleading name.
Old nftables in user space will ignore this new hook type and thus
continue to print flowtable hooks just like before, e.g.:
| family netdev {
| hook ingress device test0 {
| 0000000000 nf_flow_offload_ip_hook [nf_flow_table]
| }
| }
With this patch in place and support for the new hook info type, output
becomes more useful:
| family netdev {
| hook ingress device test0 {
| 0000000000 flowtable ip mytable myft [nf_flow_table]
| }
| }
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce a helper routine adding the nested attribute for use by a
second caller later.
Note how this introduces cancelling of 'nest2' for categorical reasons.
Since always followed by cancelling of the outer 'nest', it is
technically not needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 8fa7292fee ("treewide: Switch/rename to timer_delete[_sync]()")
switched del_timer to timer_delete, but did not modify the comment for
ip_vs_conn_expire_now(). Now fix it.
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The config snippet specifies CONFIG_SCTP_DIAG. This was never an option.
Replace CONFIG_SCTP_DIAG with the intended CONFIG_INET_SCTP_DIAG.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some specified options rely on NETFILTER_XTABLES_LEGACY to be enabled.
IP_NF_TARGET_TTL for instance depends on IP_NF_MANGLE which in turn
depends on IP_NF_IPTABLES_LEGACY -> NETFILTER_XTABLES_LEGACY.
Enable relevant iptables config options explicitly, this is needed
to avoid breakage when symbols related to iptables-legacy
will depend on NETFILTER_LEGACY resp. IP_TABLES_LEGACY.
This also means that the classic tables (Kernel modules) will
not be enabled by default, so enable them too.
Signed-off-by: Florian Westphal <fw@strlen.de>
[bigeasy: Split out the config bits from the main patch]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The seqcount xt_recseq is used to synchronize the replacement of
xt_table::private in xt_replace_table() against all readers such as
ipt_do_table()
To ensure that there is only one writer, the writing side disables
bottom halves. The sequence counter can be acquired recursively. Only the
first invocation modifies the sequence counter (signaling that a writer
is in progress) while the following (recursive) writer does not modify
the counter.
The lack of a proper locking mechanism for the sequence counter can lead
to live lock on PREEMPT_RT if the high prior reader preempts the
writer. Additionally if the per-CPU lock on PREEMPT_RT is removed from
local_bh_disable() then there is no synchronisation for the per-CPU
sequence counter.
The affected code is "just" the legacy netfilter code which is replaced
by "netfilter tables". That code can be disabled without sacrificing
functionality because everything is provided by the newer
implementation. This will only requires the usage of the "-nft" tools
instead of the "-legacy" ones.
The long term plan is to remove the legacy code so lets accelerate the
progress.
Relax dependencies on iptables legacy, replace select with depends on,
this should cause no harm to existing kernel configs and users can still
toggle IP{6}_NF_IPTABLES_LEGACY in any case.
Make EBTABLES_LEGACY, IPTABLES_LEGACY and ARPTABLES depend on
NETFILTER_XTABLES_LEGACY. Hide xt_recseq and its users,
xt_register_table() and xt_percpu_counter_alloc() behind
NETFILTER_XTABLES_LEGACY. Let NETFILTER_XTABLES_LEGACY depend on
!PREEMPT_RT.
This will break selftest expecing the legacy options enabled and will be
addressed in a following patch.
Co-developed-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit a3efd81205 ("netfilter: conntrack: move generation
seqcnt out of netns_ct") this param is unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit 9e539c5b6d ("netfilter: nf_tables: disable expression
reduction infra") this is unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit 2173c519d5 ("audit: normalize NETFILTER_PKT")
these are unused, so can be removed.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When no logger is registered, nf_conntrack_log_invalid fails to log invalid
packets, leaving users unaware of actual invalid traffic. Improve this by
loading nf_log_syslog, similar to how 'iptables -I FORWARD 1 -m conntrack
--ctstate INVALID -j LOG' triggers it.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Zi Li <zi.li@linux.dev>
Signed-off-by: Lance Yang <lance.yang@linux.dev>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add the netns field in the "nf_conntrack: table full, dropping packet"
log to help locate the specific netns when the table is full.
Signed-off-by: lvxiafei <lvxiafei@sensetime.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add the bindings for the Neural Processing Unit IP from Rockchip.
v2:
- Adapt to new node structure (one node per core, each with its own
IOMMU)
- Several misc. fixes from Sebastian Reichel
v3:
- Split register block in its constituent subblocks, and only require
the ones that the kernel would ever use (Nicolas Frattaroli)
- Group supplies (Rob Herring)
- Explain the way in which the top core is special (Rob Herring)
v4:
- Change required node name to npu@ (Rob Herring and Krzysztof Kozlowski)
- Remove unneeded items: (Krzysztof Kozlowski)
- Fix use of minItems/maxItems (Krzysztof Kozlowski)
- Add reg-names to list of required properties (Krzysztof Kozlowski)
- Fix example (Krzysztof Kozlowski)
v5:
- Rename file to rockchip,rk3588-rknn-core.yaml (Krzysztof Kozlowski)
- Streamline compatible property (Krzysztof Kozlowski)
v6:
- Remove mention to NVDLA, as the hardware is only incidentally related
(Kever Yang)
- Mark pclk and npu clocks as required by all clocks (Rob Herring)
v7:
- Remove allOf section, not needed now that all nodes require 4 clocks
(Heiko Stübner)
v8:
- Remove notion of top core (Robin Murphy)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250721-6-10-rocket-v9-6-77ebd484941e@tomeuvizoso.net
The NPU cores have their own access to the memory bus, and this isn't
cache coherent with the CPUs.
Add IOCTLs so userspace can mark when the caches need to be flushed, and
also when a writer job needs to be waited for before the buffer can be
accessed from the CPU.
Initially based on the same IOCTLs from the Etnaviv driver.
v2:
- Don't break UABI by reordering the IOCTL IDs (Jeff Hugo)
v3:
- Check that padding fields in IOCTLs are zero (Jeff Hugo)
v6:
- Fix conversion logic to make sure we use DMA_BIDIRECTIONAL when needed
(Lucas Stach)
v8:
- Always sync BOs in both directions (Robin Murphy)
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250721-6-10-rocket-v9-5-77ebd484941e@tomeuvizoso.net
