Version 1 and 2 of DDRC PMU also use different HID. Make use of
struct acpi_device_id::driver_data for version specific information
rather than judge the version register. This will help to
simplify the probe process and also a bit easier for extension.
In order to support this extend struct hisi_pmu_dev_info for version
specific counter bits and event range.
Signed-off-by: Junhao He <hejunhao3@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20250619125557.57372-2-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
A multi-link client can use any link for transmissions. It can decide to
put one link in power save mode for longer periods while listening on the
other links as per MLD listen interval. Unicast management frames sent to
that link station might get dropped if that link station is in power save
mode or inactive. In such cases, firmware can take decision on which link
to use.
Allow the firmware to decide on which link management frame should be
sent on, by filling the hardware link with maximum value of u32, so that
the firmware will not have a specific link to transmit data on and so
the management frames will be link agnostic. For QCN devices, all action
frames are marked as link agnostic. For WCN devices, if the device is
configured as an AP, then all frames other than probe response frames,
authentication frames, association response frames, re-association response
frames and ADDBA response frames are marked as link agnostic and if the
device is configured as a station, then all frames other than probe request
frames, authentication frames, de-authentication frames and ADDBA response
frames are marked as link agnostic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711091704.3704379-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The QCN9274 supports two memory profiles: a default profile and a
low-memory profile. The driver signals the firmware to enable
low-memory optimizations using the QMI initialization service.
Add support to select the low-memory profile on system with less than
512 MB RAM.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-5-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Refactor macros to compute values dynamically at runtime based on the
ath12k_mem_profile_based_param structure.
Remove hardcoded logic to allow driver to operate more efficiently in
memory-constrained platforms without significant functional impact.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-4-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, host sends num_tids (number of TID (Traffic Identifier))
value to firmware via WMI_INIT_CMD during WMI initialization. However,
the firmware does not use this value, as it determines the number of
TIDs using its own internal logic.
Hence, remove the redundant num_tids calculation logic for QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-3-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce ath12k_mem_profile_based_param structure to define
configuration parameters for both default and low-memory profiles.
Add support for enabling the low-memory profile in the follow-up
patch by making the following changes:
- Reduce sizes for transmit, receive, and monitor descriptor rings.
- Reduce transmit and receive descriptor count.
- Limit the maximum number of virtual devices (vdevs) to 9.
- Reduce the maximum number of client support per radio.
Centralize these parameters in the ath12k_mem_profile_based_param
structure to simplify switching between memory profiles.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-2-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Refresh the x86-32 defconfig to pick up changes in the
general Kconfig environment: removed options, different
defaults, renames, etc.
No changes to the actual result of 'make ARCH=i386 defconfig'.
[ bp: Fold in a fix as reported by Andy:
https://lore.kernel.org/r/20250626150118.318836-1-andriy.shevchenko@linux.intel.com ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jürgen Groß <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20250515132719.31868-2-mingo@kernel.org
NI-700 has a distinct PMU interrupt output for each Clock Domain,
however some integrations may still combine these together externally.
The initial driver didn't attempt to support this, in anticipation of a
more general solution for IRQ sharing between system PMU instances, but
that's still a way off, so let's make this intermediate step for now to
at least allow sharing IRQs within an individual NI instance.
Now that CPU affinity and migration are cleaned up, it's fairly
straightforward to adopt similar logic to arm-cmn, to identify CDs with
a common interrupt and loop over them directly in the handler.
Signed-off-by: Shouping Wang <allen.wang@hj-micro.com>
[ rm: Rework for affinity handling, cosmetics, new commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/f62db639d3b54c959ec477db7b8ccecbef1ca310.1752256072.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Since overflow interrupts from the individual PMUs are infrequent and
unlikely to coincide, and we make no attempt to balance them across
CPUs anyway, there's really not much point tracking a separate CPU
affinity per PMU. Move the CPU affinity and hotplug migration up to
the NI instance level.
Tested-by: Shouping Wang <allen.wang@hj-micro.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/00b622872006c2f0c89485e343b1cb8caaa79c47.1752256072.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The command word members of struct nvme_common_command are __le32 type,
so use helper le32_to_cpu() to read them properly.
Fixes: 9f079dda14 ("nvme: allow passthru cmd error logging")
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When inserting a namespace into the controller's namespace list, the
function uses list_add_rcu() when the namespace is inserted in the middle
of the list, but falls back to a regular list_add() when adding at the
head of the list.
This inconsistency could lead to race conditions during concurrent
access, as users might observe a partially updated list. Fix this by
consistently using list_add_rcu() in both code paths to ensure proper
RCU protection throughout the entire function.
Fixes: be647e2c76 ("nvme: use srcu for iterating namespace list")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The volatile_reg function is named as tps6287x_volatile_reg by mistake
when enabing the REGCACHE_MAPLE support.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://patch.msgid.link/20250714010456.4906-1-jszhang@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The current SPI framework does not verify if the SPI device supports
8 IO mode when doing an 8-bit transfer. This patch adds a check to
ensure that if the transfer tx_nbits or rx_nbits is 8, the SPI mode must
support 8 IO. If not, an error is returned, preventing undefined behavior.
Fixes: d6a711a898 ("spi: Fix OCTAL mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://patch.msgid.link/20250714031023.504752-1-linchengming884@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to bring up secondary CPUs main CPU write trampoline
code to SRAM. The trampoline code is written while secondary
CPUs are powered on (at least that true for RK3188 CPU).
Sometimes that leads to kernel hang. Probably because secondary
CPU execute trampoline code while kernel doesn't expect.
The patch moves SRAM initialization step to the point where all
secondary CPUs are powered down.
That fixes rarely hangs on RK3188:
[ 0.091568] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.091996] rockchip_smp_prepare_cpus: ncores 4
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Link: https://lore.kernel.org/r/20250703140453.1273027-1-al.kochet@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This reverts commit 465b9ee0ee.
Such notifications fit better into core or nfnetlink_hook code,
following the NFNL_MSG_HOOK_GET message format.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Its a kernel implementation detail, at least at this time:
We can later decide to revert this patch if there is a compelling
reason, but then we should also remove the ifdef that prevents exposure
of ip_conntrack_status enum IPS_NAT_CLASH value in the uapi header.
Clash entries are not included in dumps (true for both old /proc
and ctnetlink) either. So for now exclude the clash bit when dumping.
Fixes: 7e5c6aa67e ("netfilter: nf_tables: add packets conntrack state to debug trace info")
Link: https://lore.kernel.org/netfilter-devel/aGwf3dCggwBlRKKC@strlen.de/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The selftest doesn't cover this error path:
scratch = *raw_cpu_ptr(m->scratch);
if (unlikely(!scratch)) { // here
cover this too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Previous patch added a new clash resolution test case.
Also use this during conntrack resize stress test in addition
to icmp ping flood.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a dedicated test to exercise conntrack clash resolution path.
Test program emits 128 identical udp packets in parallel, then reads
back replies from socat echo server.
Also check (via conntrack -S) that the clash path was hit at least once.
Due to the racy nature of the test its possible that despite the
threaded program all packets were processed in-order or on same cpu,
emit a SKIP warning in this case.
Two tests are added:
- one to test the simpler, non-nat case
- one to exercise clash resolution where packets
might have different nat transformations attached to them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Extend the resize test:
- continuously dump table both via /proc and ctnetlink interfaces while
table is resized in a loop.
- if socat is available, send udp packets in additon to ping requests.
- increase/decrease the icmp and udp timeouts while resizes are happening.
This makes sure we also exercise the 'ct has expired' check that happens
on conntrack lookup.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix several minor typo errors in comments:
- Remove duplicated word "a" in "a a VID / GroupID".
- Correct "Opcopdes" to "Opcodes" in CXL spec reference.
- Fix spelling of "implemnted" to "implemented".
Improves code readability and documentation consistency.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://lore.kernel.org/r/20250624194350.109790-4-alok.a.tiwari@oracle.com
Signed-off-by: Will Deacon <will@kernel.org>
The IRQ name format string used in devm_kasprintf() mistakenly included
a newline character "\n".
This could lead to confusing log output or misformatted names in sysfs
or debug messages.
This fix removes the newline to ensure proper IRQ naming.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://lore.kernel.org/r/20250624194350.109790-3-alok.a.tiwari@oracle.com
Signed-off-by: Will Deacon <will@kernel.org>
The previous code mistakenly swapped the count and size parameters.
This fix corrects the argument order in devm_kcalloc() to follow the
conventional count, size form, avoiding potential confusion or bugs.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://lore.kernel.org/r/20250624194350.109790-2-alok.a.tiwari@oracle.com
Signed-off-by: Will Deacon <will@kernel.org>
It's possible for a poll_table to be null. This can happen if an
end-user just wants to know if a resource has events right now without
registering a waiter for when events become available. Furthermore,
these null pointers should be handled transparently by the API, so we
should not change `from_ptr` to return an `Option`. Thus, change
`PollTable` to wrap a raw pointer rather than use a reference so that
you can pass null.
Comments mentioning `struct poll_table` are changed to just `poll_table`
since `poll_table` is a typedef. (It's a typedef because it's supposed
to be opaque.)
Reviewed-by: Benno Lossin <lossin@kernel.org>
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
The Lenovo Yoga Book 9i GenX has the wrong values in the cirrus,dev-index
_DSD property. Add a fixup for this model to ignore the property and
hardcode the index from the I2C bus address.
The error in the cirrus,dev-index property would prevent the second amp
instance from probing. The component binding would never see all the
required instances and so there would not be a binding between
patch_realtek.c and the cs35l56 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reported-by: Brian Howard <blhoward2@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220228
Link: https://patch.msgid.link/20250714110154.204740-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bootloader configures a reserved memory region for framebuffer,
which is protected by the IOMMU. The kernel-side driver is oblivious as
of which memory region is set up by the bootloader. In such case, the
IOMMU tries to reference the reserved region - which is not reserved in
the kernel anymore - and it results in an unrecoverable page fault. More
information about it is provided in [1].
Add support for reserved regions using iommu_dma_get_resv_regions().
For OF supported boards, this requires defining the region in the
iommu-addresses property of the IOMMU owner's node.
Link: https://lore.kernel.org/r/544ad69cba52a9b87447e3ac1c7fa8c3@disroot.org [1]
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250712-exynos-sysmmu-resv-regions-v1-1-e79681fcab1a@disroot.org
Signed-off-by: Will Deacon <will@kernel.org>
Add the HiSilicon uncore frequency scaling driver for Kunpeng SoCs based on
the devfreq framework. The uncore domain contains shared computing
resources, including system interconnects and L3 cache. The uncore
frequency significantly impacts the system-wide performance as well as
power consumption. This driver adds support for runtime management of
uncore frequency from kernel and userspace. The main function includes
setting and getting frequencies, changing frequency scaling policies, and
querying the list of CPUs whose performance is significantly related to
this uncore frequency domain, etc. The driver communicates with a platform
controller through an ACPI PCC mailbox to take the actual actions of
frequency scaling.
Co-developed-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Signed-off-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20250623143401.4095045-3-zhanjie9@hisilicon.com/
Extend the devfreq_dev_profile to allow drivers optionally create
device-specific sysfs ABIs together with other common devfreq ABIs under
the devfreq device path.
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20250623143401.4095045-2-zhanjie9@hisilicon.com/
On SM8250 / QRB5165-RB5 using PRR bits resets the device, most likely
because of the hyp limitations. Disable PRR support on that platform.
Fixes: 7f2ef1bfc7 ("iommu/arm-smmu: Add support for PRR bit setup")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Rob Clark <robin.clark@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250705-iommu-fix-prr-v2-1-406fecc37cf8@oss.qualcomm.com
Signed-off-by: Will Deacon <will@kernel.org>
The error path for err_free_master_domain leaks the vmaster. Move all
the kfrees for vmaster into the goto error section.
Fixes: cfea71aea9 ("iommu/arm-smmu-v3: Put iopf enablement in the domain attach path")
Cc: stable@vger.kernel.org
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/20250711204020.1677884-1-nicolinc@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Commit 33729a5fc0 ("iommu/io-pgtable-arm: Remove split on unmap
behavior") removed the last user of the macro iopte_prot. Remove the
macro definition of iopte_prot as well as three other related
definitions.
Fixes: 33729a5fc0 ("iommu/io-pgtable-arm: Remove split on unmap behavior")
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20250708211705.1567787-1-danielmentz@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Merge the pmdomain fixes for v6.16-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.17.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently cpu hotplug with the PREEMPT_RT option set in the kernel is
not supported because the underlying generic power domain functions
used in the cpu hotplug callbacks are incompatible from a lock point
of view. This situation prevents the suspend to idle to reach the
deepest idle state for the "cluster" as identified in the
undermentioned commit.
Use the compatible ones when PREEMPT_RT is enabled and remove the
boolean disabling the hotplug callbacks with this option.
With this change the platform can reach the deepest idle state
allowing at suspend time to consume less power.
Tested-on Lenovo T14s with the following script:
echo 0 > /sys/devices/system/cpu/cpu3/online
BEFORE=$(cat /sys/kernel/debug/pm_genpd/power-domain-cpu-cluster0/idle_states | grep S0 | awk '{ print $3 }') ;
rtcwake -s 1 -m mem;
AFTER=$(cat /sys/kernel/debug/pm_genpd/power-domain-cpu-cluster0/idle_states | grep S0 | awk '{ print $3 }');
if [ $BEFORE -lt $AFTER ]; then
echo "Test successful"
else
echo "Test failed"
fi
echo 1 > /sys/devices/system/cpu/cpu3/online
Fixes: 1c4b2932bd ("cpuidle: psci: Enable the hierarchical topology for s2idle on PREEMPT_RT")
Cc: Raghavendra Kakarla <quic_rkakarla@quicinc.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250709154728.733920-1-daniel.lezcano@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm allocators for enabling the bus clock and
clk_rate_exclusive_get(). This simplifies error handling and the remove
callback.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20250513203908.205060-2-u.kleine-koenig@baylibre.com/
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Commit 96ffcdf239 ("PM / devfreq: Remove redundant governor_name from
struct devfreq") removes governor_name and uses governor->name to replace
it. But devfreq->governor may be NULL and directly using
devfreq->governor->name may cause null pointer exception. Move the check of
governor to before using governor->name.
Fixes: 96ffcdf239 ("PM / devfreq: Remove redundant governor_name from struct devfreq")
Signed-off-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Link: https://lore.kernel.org/lkml/20250421030020.3108405-5-zhenglifeng1@huawei.com/
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The calling of devfreq_get_freq_range() in devfreq_add_device() is
redundant because min_freq and max_freq are never used. Remove it.
Signed-off-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Link: https://lore.kernel.org/lkml/20250421030020.3108405-4-zhenglifeng1@huawei.com/
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Limit max_freq in devfreq_get_freq_range() with scaling_min_freq to avoid
showing an unreachable freq when reading it.
Use macro clamp to simplify code.
Signed-off-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Link: https://lore.kernel.org/lkml/20250421030020.3108405-3-zhenglifeng1@huawei.com/
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
qcom uses the ARM_32_LPAE_S1 format which uses the ARM long descriptor
page table. Eventually arm_32_lpae_alloc_pgtable_s1() will adjust
the pgsize_bitmap with:
cfg->pgsize_bitmap &= (SZ_4K | SZ_2M | SZ_1G);
So the current declaration is nonsensical. Fix it to be just SZ_4K which
is what it has actually been using so far. Most likely the qcom driver
copy and pasted the pgsize_bitmap from something using the ARM_V7S format.
Fixes: db64591de4 ("iommu/qcom: Remove iommu_ops pgsize_bitmap")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYvif6kDDFar5ZK4Dff3XThSrhaZaJundjQYujaJW978yg@mail.gmail.com/
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/0-v1-65a7964d2545+195-qcom_pgsize_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Support mute LED on keyboard for Lenovo Yoga series products with
Realtek ALC287 chipset.
Tested on Lenovo Slim Pro 7 14APH8.
[ slight comment cleanup by tiwai ]
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20250714094655.4657-1-xy-jackie@139.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Luca Weiss <luca.weiss@fairphone.com>:
Document and add support for the regulators on PM7550 and PMR735B, which
can be paired with the Milos SoC.
Merge series from Peng Fan <peng.fan@nxp.com>:
This patchset is a pick up of patch 1,2 from [1]. And I also collect
Linus's R-b for patch 2. After this patchset, there is only one user of
of_gpio.h left in sound driver(pxa2xx-ac97).
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
Patch 1 is to drop legacy platform data which in-tree no users are using it
Patch 2 is to convert to GPIO descriptors
Checking the DTS that use the device, all are using GPIOD_ACTIVE_LOW
polarity for reset-gpios, so all should work as expected with this patch.
[1] https://lore.kernel.org/all/20250408-asoc-gpio-v1-0-c0db9d3fd6e9@nxp.com/
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Tidy up a bunch of makefile and Kconfig things, and pull the HID and IRQ
into the main SDCA module.
Changes since v1:
- Don't expose SND_SOC_SDCA to the user
- Simplify the makefile bits for HID and IRQ
Thanks,
Charles
Charles Keepax (2):
ASoC: SDCA: Kconfig/Makefile fixups
ASoC: SDCA: Pull HID and IRQ into the primary SDCA module
sound/soc/sdca/Kconfig | 13 +++++++++----
sound/soc/sdca/Makefile | 12 ++++--------
sound/soc/sdca/sdca_functions.c | 1 -
sound/soc/sdca/sdca_hid.c | 2 +-
sound/soc/sdca/sdca_interrupts.c | 8 ++++----
5 files changed, 18 insertions(+), 18 deletions(-)
--
2.39.5
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
ASoC has 2 functions to set bias level.
(A) snd_soc_dapm_force_bias_level()
(B) snd_soc_dapm_set_bias_level()
(A) sets dapm->bias_level, but (B) is not.
I think we should set it on both (A) and (B).
I think it is miss or bug, but Samsung is the only vendor that feels a
problem about this.
I think this patch (= [1/5]) is correct approach, but some non-samsung
vendor might get affect from this patch-set, so I added [RFC] on this
patch-set.
Furthermore, (B) cares both Card and Component, (A) cares Component only.
I guess it is the reason why it is called as "force" bias_level function.
(A) is used from each drivers, (B) is used from soc-dapm only.
I'm not 100% sure though, except special cases, each driver should use (B),
I guess ?
The logic in cache_tag_flush_all() to iterate over cache tags and issue
TLB invalidations is largely duplicated in cache_tag_flush_range(), with
the only difference being the range parameters.
Extend cache_tag_flush_range() to handle a full address space flush when
called with start = 0 and end = ULONG_MAX. This allows
cache_tag_flush_all() to simply delegate to cache_tag_flush_range()
Signed-off-by: Ethan Milon <ethan.milon@eviden.com>
Link: https://lore.kernel.org/r/20250708214821.30967-2-ethan.milon@eviden.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20250714045028.958850-12-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
The function cache_tag_flush_all() was originally implemented with
incorrect device TLB invalidation logic that does not handle PASID, in
commit c4d27ffaa8 ("iommu/vt-d: Add cache tag invalidation helpers")
This causes regressions where full address space TLB invalidations occur
with a PASID attached, such as during transparent hugepage unmapping in
SVA configurations or when calling iommu_flush_iotlb_all(). In these
cases, the device receives a TLB invalidation that lacks PASID.
This incorrect logic was later extracted into
cache_tag_flush_devtlb_all(), in commit 3297d047cd ("iommu/vt-d:
Refactor IOTLB and Dev-IOTLB flush for batching")
The fix replaces the call to cache_tag_flush_devtlb_all() with
cache_tag_flush_devtlb_psi(), which properly handles PASID.
Fixes: 4f609dbff5 ("iommu/vt-d: Use cache helpers in arch_invalidate_secondary_tlbs")
Fixes: 4e589a5368 ("iommu/vt-d: Use cache_tag_flush_all() in flush_iotlb_all")
Signed-off-by: Ethan Milon <ethan.milon@eviden.com>
Link: https://lore.kernel.org/r/20250708214821.30967-1-ethan.milon@eviden.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20250714045028.958850-11-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
Make First/Second stage specific functions that follow the same pattern in
intel_iommu_domain_alloc_first/second_stage() for computing
EOPNOTSUPP. This makes the code easier to understand as if we couldn't
create a domain with the parameters for this IOMMU instance then we
certainly are not compatible with it.
Check superpage support directly against the per-stage cap bits and the
pgsize_bitmap.
Add a note that the force_snooping is read without locking. The locking
needs to cover the compatible check and the add of the device to the list.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/7-v3-dbbe6f7e7ae3+124ffe-vtd_prep_jgg@nvidia.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20250714045028.958850-10-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
