Exynos 2200 SoC is an ARMv8 mobile SoC found in the Samsung Galaxy S22
(r0s), S22+ (g0s), S22 Ultra (b0s) Add minimal support for that SoC,
including psci, pmu, chipid, architecture timer and mct, pinctrl,
clocks and usb.
The devices using this SoC suffer from an issue caused by the stock
Samsung bootloader, as it doesn't configure CNTFRQ_EL0. Hence it's
needed to hardcode the adequate frequency in the timer node,
otherwise the kernel panics.
Further platform support will be added over time.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Link: https://lore.kernel.org/r/20250504145907.1728721-3-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add binding for the Samsung Galaxy S22+ (SM-S906B) board, codenamed G0S,
which is based on the Samsung Exynos2200 SoC.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250504145907.1728721-2-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The probe and remove functions in the mt8183-afe-pcm driver repeatedly uses
`&pdev->dev` for |struct device *|, but then assigns this value to
`afe->dev` and uses that in other places in the same function.
Store `&pdev->dev` in a local pointer and use that exclusively to avoid
the numerous dereferences and to make the code more consistent. Lines
are reflowed where it makes sense.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-10-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe and remove functions in the mt8183-afe-pcm driver repeatedly uses
`&pdev->dev` for |struct device *|, but then assigns this value to
`afe->dev` and uses that in other places in the same function.
Store `&pdev->dev` in a local pointer and use that exclusively to avoid
the numerous dereferences and to make the code more consistent. Lines
are reflowed where it makes sense.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-9-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The AFE DMA hardware supports up to 34 bits for DMA addresses. This is
missing from the driver and prevents reserved memory regions from
working properly when the allocated region is above the 4GB line.
Fill in the related register offsets for each DAI, and also set the
DMA mask. Also fill in the LSB end register offsets for completeness.
Fixes: a94aec035a ("ASoC: mediatek: mt8183: add platform driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-8-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 32c9c06adb ("ASoC: mediatek: disable buffer pre-allocation")
buffer pre-allocation was disabled to accommodate newer platforms that
have a limited reserved memory region for the audio frontend.
Turns out disabling pre-allocation across the board impacts platforms
that don't have this reserved memory region. Buffer allocation failures
have been observed on MT8173 and MT8183 based Chromebooks under low
memory conditions, which results in no audio playback for the user.
Since some MediaTek platforms already have dedicated reserved memory
pools for the audio frontend, the plan is to enable this for all of
them. This requires device tree changes. As a fallback, reinstate the
original policy of pre-allocating audio buffers at probe time of the
reserved memory pool cannot be found or used.
This patch covers the MT8173, MT8183, MT8186 and MT8192 platforms for
now, the reason being that existing MediaTek platform drivers that
supported reserved memory were all platforms that mainly supported
ChromeOS, and is also the set of devices that I can verify.
Fixes: 32c9c06adb ("ASoC: mediatek: disable buffer pre-allocation")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-7-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is desirable to reserve memory for the audio frontend.
Allow the "memory-region" property, to be used to point to a reserved
memory region.
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-6-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is desirable to reserve memory for the audio frontend.
Allow the "memory-region" property, to be used to point to a reserved
memory region.
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-5-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is desirable to reserve memory for the audio frontend.
Allow the "memory-region" property, to be used to point to a reserved
memory region.
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-4-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio subsystem sits under a controllable power domain.
Add it to the binding.
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-3-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the MT8173 AFE (audio frontend) binding from text to dt-schema
in YAML. "clocks" is added to the list of required properties to match
"clock-names". And the example was slightly fixed up in style. Otherwise
everything is as before.
A contributer and maintainer for a recently added MediaTek audio binding
was chosen instead of the original submitter.
Cc: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250612074901.4023253-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add client id to the drm_file_error api, client id
is a unique id for each drm fd and is quite useful
for debugging.
v2: Swapped client id and client name order [Chrisitan]
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250530062929.1954784-1-sunil.khatri@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
MSI Bravo 17 (D7VF), like other laptops from the family,
has broken ACPI tables and needs a quirk for internal mic
to work properly.
Signed-off-by: Gabriel Santese <santesegabriel@gmail.com>
Link: https://patch.msgid.link/20250530005444.23398-1-santesegabriel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This function takes super_lock in shared mode, so it should release the
same lock.
Cc: stable@vger.kernel.org # v6.16-rc1
Fixes: af7551cf13 ("super: remove pointless s_root checks")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Link: https://lore.kernel.org/20250611164044.GF6138@frogsfrogsfrogs
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
We want to print the name in case of mkdir failure and now we will
get a cryptic (efault) as name.
Fixes: c54b386969 ("VFS: Change vfs_mkdir() to return the dentry.")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/20250612072245.2825938-1-amir73il@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add the new firmware filename suffix used for SoundWire systems with
CS35L57, CS35L63 or CS35L56 later than B0 silicon. This uses the SoundWire
physical address of the amp to identify which firmware file to load on that
amp.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250612121428.1667-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the SoundWire link number and device unique ID as the firmware file
qualifier suffix on CS35L56 B0 if .bin files are not found with the older
suffix. Some changes in wm_adsp needed to support this have been included
in this patch because they are trivial.
The allows future products with CS35L56 B0 silicon to use the same firmware
file naming as CS35L57 and cs35L63, while retaining backward compatibility
for firmware that has already been published with the old naming scheme.
The old suffix is searched first, partly because there are already many
files using that naming scheme, but also because they are a smaller subset
of all the possible fallback name options offered by wm_adsp so we know
that it will either find the qualified files or fail. All the firmware
files already published have the wmfw qualified with only the ACPI SSID and
the bin files qualified with both SSID and the suffix.
Originally, the firmware file names indicated which amplifier instance they
were for by appending the ALSA prefix string. This is the standard ASoC way
of distinguishing different instances of the same device. However, on
SoundWire systems the SoundWire physical unique address is available as a
unique identifier for each amp, and this address is hardwired by the
address pin on the amp.
The firmware files are specific for each physical amp so they must be
applied to that amp. Using the ALSA prefix for the filename qualifier means
that to name a firmware file it must be determined what prefix string the
machine driver will assign to each device and then use that to name the
firmware file correctly. This is straightforward in traditional ASoC
systems where the machine driver is specific to a particular piece of
hardware. But on SoundWire the machine driver is generic and can handle a
very wide range of hardware. It is more difficult to determine exactly what
the prefix will be on any particular production device, and more prone to
mistakes. Also, when the machine driver switches to generating this
automatically from SDCA properties in ACPI, there is an additional layer of
complexity in determining the mapping. This uncertainty is unnecessary
because the firmware is built for a specific amp. with known address, so we
can use that directly instead of introducing a redundant intermediate
alias. This ensures the firmware is applied to the amp it was intended for.
There are already many published firmware for CS35L56 B0 silicon so this
first looks for the original name suffix, to keep backward compatibility.
If this doesn't find .bin files it will switch to using the new name suffix
so that future products using CS35L56 B0 can start to use the new suffix.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250612121428.1667-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the SoundWire link number and device unique ID as the firmware file
qualifier suffix on CS35L57, CS35L63 and revisions of CS35L56 after B0. The
change in wm_adsp needed to support this has been included in this patch
because it is fairly trivial.
Originally, the firmware file names indicated which amplifier instance they
were for by appending the ALSA prefix string. This is the standard ASoC way
of distinguishing different instances of the same device. However, on
SoundWire systems the SoundWire physical unique address is available as a
unique identifier for each amp, and this address is hardwired by a pin on
the amp.
The firmware files are specific for each physical amp so they must be
applied to that amp. Using the ALSA prefix for the filename qualifier means
that to name a firmware file it must be determined what prefix string the
machine driver will assign to each device and then use that to name the
firmware file correctly. This is straightforward in traditional ASoC
systems where the machine driver is specific to a particular piece of
hardware. But on SoundWire the machine driver is generic and can handle a
very wide range of hardware. It is more difficult to determine exactly what
the prefix will be on any particular production device, and more prone to
mistakes. Also, when the machine driver switches to generating this
automatically from SDCA properties in ACPI, there is an additional layer of
complexity in determining the mapping. This uncertainty is unnecessary
because the firmware is built for a specific amp. with known address, so we
can use that directly instead of introducing the redundant intermediate
alias. This ensures the firmware is applied to the amp it was intended for.
There have not been any firmwares published for CS35L57 or CS35L63, so
these can safely be switched to using the SoundWire unique address as the
suffix string. Also note that the machine driver in older kernel version
only has match entries for the CS35L56 Soundwire identity so any future
product with a cs35L57 or CS35L63 would require a new kernel anyway.
There are already many published firmware for CS35L56 B0 silicon so this
keeps the original naming scheme on those, to preserve backward
compatibility.
Note that although sdw_slave.id contains a unique_id field, this cannot
be trusted because the SoundWire core code also puts magic values into it
that it uses as a flag. So the unique ID is read from the chip register.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250612121428.1667-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64 ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
pinctrl-intel.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
So fix these build warnings for the driver code.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When checking for unsupported expect an error is printed every time.
This spams the log for platforms where this is expected, e.g. ls1028a
having a Vivante (etnaviv) GPU and Mali display processor.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/r/20250523064042.3275926-1-alexander.stein@ew.tq-group.com
The number of columns relates to the width, not the height. Use the
correct variable.
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Fixes: fdd591e00a ("drm/ssd130x: Add support for the SSD132x OLED controller family")
Link: https://lore.kernel.org/r/20250611111307.1814876-1-jkeeping@inmusicbrands.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
We currently use multiple CONFIG_UNIX guards. This looks messy and makes
the code harder to follow and maintain. Use a helper function
coredump_sock_connect() that handles the connect portion. This allows us
to remove the CONFIG_UNIX guard in the main do_coredump() function.
Link: https://lore.kernel.org/20250605-schlamm-touren-720ba2b60a85@brauner
Signed-off-by: Christian Brauner <brauner@kernel.org>
Christian Brauner <brauner@kernel.org> says:
In addition to the extensive selftests I've already written a
(non-production ready) simple Rust coredump server for this in
userspace:
https://github.com/brauner/dumdum.git
Extend the coredump socket to allow the coredump server to tell the
kernel how to process individual coredumps. This allows for fine-grained
coredump management. Userspace can decide to just let the kernel write
out the coredump, or generate the coredump itself, or just reject it.
When the crashing task connects to the coredump socket the kernel will
send a struct coredump_req to the coredump server. The kernel will set
the size member of struct coredump_req allowing the coredump server how
much data can be read.
The coredump server uses MSG_PEEK to peek the size of struct
coredump_req. If the kernel uses a newer struct coredump_req the
coredump server just reads the size it knows and discard any remaining
bytes in the buffer. If the kernel uses an older struct coredump_req
the coredump server just reads the size the kernel knows.
The returned struct coredump_req will inform the coredump server what
features the kernel supports. The coredump_req->mask member is set to
the currently know features.
The coredump server may only use features whose bits were raised by the
kernel in coredump_req->mask.
In response to a coredump_req from the kernel the coredump server sends
a struct coredump_ack to the kernel. The kernel informs the coredump
server what version of struct coredump_ack it supports by setting struct
coredump_req->size_ack to the size it knows about. The coredump server
may only send as many bytes as coredump_req->size_ack indicates (a
smaller size is fine of course). The coredump server must set
coredump_ack->size accordingly.
The coredump server sets the features it wants to use in struct
coredump_ack->mask. Only bits returned in struct coredump_req->mask may
be used.
In case an invalid struct coredump_ack is sent to the kernel a non-zero
u32 integer is sent indicating the reason for the failure. If it was
successful a zero u32 integer is sent.
In the initial version the following features are supported in
coredump_{req,ack}->mask:
* COREDUMP_KERNEL
The kernel will write the coredump data to the socket.
* COREDUMP_USERSPACE
The kernel will not write coredump data but will indicate to the
parent that a coredump has been generated. This is used when userspace
generates its own coredumps.
* COREDUMP_REJECT
The kernel will skip generating a coredump for this task.
* COREDUMP_WAIT
The kernel will prevent the task from exiting until the coredump
server has shutdown the socket connection.
The flexible coredump socket can be enabled by using the "@@" prefix
instead of the single "@" prefix for the regular coredump socket:
@@/run/systemd/coredump.socket
will enable flexible coredump handling. Current kernels already enforce
that "@" must be followed by "/" and will reject anything else. So
extending this is backward and forward compatible.
Link: https://lore.kernel.org/20250603-work-coredump-socket-protocol-v2-0-05a5f0c18ecc@kernel.org
* patches from https://lore.kernel.org/20250603-work-coredump-socket-protocol-v2-0-05a5f0c18ecc@kernel.org:
selftests/coredump: add coredump server selftests
tools: add coredump.h header
selftests/coredump: cleanup coredump tests
selftests/coredump: fix build
coredump: allow for flexible coredump handling
Signed-off-by: Christian Brauner <brauner@kernel.org>
Make the selftests we added this cycle easier to read.
Link: https://lore.kernel.org/20250603-work-coredump-socket-protocol-v2-3-05a5f0c18ecc@kernel.org
Acked-by: Lennart Poettering <lennart@poettering.net>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Fix various warnings in the selftest build.
Link: https://lore.kernel.org/20250603-work-coredump-socket-protocol-v2-2-05a5f0c18ecc@kernel.org
Acked-by: Lennart Poettering <lennart@poettering.net>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Extend the coredump socket to allow the coredump server to tell the
kernel how to process individual coredumps.
When the crashing task connects to the coredump socket the kernel will
send a struct coredump_req to the coredump server. The kernel will set
the size member of struct coredump_req allowing the coredump server how
much data can be read.
The coredump server uses MSG_PEEK to peek the size of struct
coredump_req. If the kernel uses a newer struct coredump_req the
coredump server just reads the size it knows and discard any remaining
bytes in the buffer. If the kernel uses an older struct coredump_req
the coredump server just reads the size the kernel knows.
The returned struct coredump_req will inform the coredump server what
features the kernel supports. The coredump_req->mask member is set to
the currently know features.
The coredump server may only use features whose bits were raised by the
kernel in coredump_req->mask.
In response to a coredump_req from the kernel the coredump server sends
a struct coredump_ack to the kernel. The kernel informs the coredump
server what version of struct coredump_ack it supports by setting struct
coredump_req->size_ack to the size it knows about. The coredump server
may only send as many bytes as coredump_req->size_ack indicates (a
smaller size is fine of course). The coredump server must set
coredump_ack->size accordingly.
The coredump server sets the features it wants to use in struct
coredump_ack->mask. Only bits returned in struct coredump_req->mask may
be used.
In case an invalid struct coredump_ack is sent to the kernel a non-zero
u32 integer is sent indicating the reason for the failure. If it was
successful a zero u32 integer is sent.
In the initial version the following features are supported in
coredump_{req,ack}->mask:
* COREDUMP_KERNEL
The kernel will write the coredump data to the socket.
* COREDUMP_USERSPACE
The kernel will not write coredump data but will indicate to the
parent that a coredump has been generated. This is used when userspace
generates its own coredumps.
* COREDUMP_REJECT
The kernel will skip generating a coredump for this task.
* COREDUMP_WAIT
The kernel will prevent the task from exiting until the coredump
server has shutdown the socket connection.
The flexible coredump socket can be enabled by using the "@@" prefix
instead of the single "@" prefix for the regular coredump socket:
@@/run/systemd/coredump.socket
will enable flexible coredump handling. Current kernels already enforce
that "@" must be followed by "/" and will reject anything else. So
extending this is backward and forward compatible.
Link: https://lore.kernel.org/20250603-work-coredump-socket-protocol-v2-1-05a5f0c18ecc@kernel.org
Acked-by: Lennart Poettering <lennart@poettering.net>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
irq_domain_create_simple() takes fwnode as the first argument. It can be
extracted from the struct device using dev_fwnode() helper instead of
using of_node with of_fwnode_handle().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611104348.192092-12-jirislaby@kernel.org
[krzk: Dropped redundant parts of commit msg]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
- Implement CpuId rust abstraction and use it to fix doctest failure
(Viresh Kumar).
- Minor cleanups in the `# Safety` sections for cpufreq abstractions
(Viresh Kumar).
-----BEGIN PGP SIGNATURE-----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=SgvH
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-fixes-6.16-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge CPUFreq fixes for 6.16-rc from Viresh Kumar:
"- Implement CpuId rust abstraction and use it to fix doctest failure
(Viresh Kumar).
- Minor cleanups in the `# Safety` sections for cpufreq abstractions
(Viresh Kumar)."
* tag 'cpufreq-arm-fixes-6.16-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
rust: cpu: Add CpuId::current() to retrieve current CPU ID
rust: Use CpuId in place of raw CPU numbers
rust: cpu: Introduce CpuId abstraction
cpufreq: Convert `/// SAFETY` lines to `# Safety` sections
hmm_pfn_to_page() does not return NULL. ib_umem_odp_map_dma_and_lock()
should return an error in case the target pages cannot be mapped until
timeout, so these checks can safely be removed.
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Daisuke Matsuda <dskmtsd@gmail.com>
Link: https://patch.msgid.link/20250611162758.10000-1-dskmtsd@gmail.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
i915_pmu.c may fail to build with GCOV and AutoFDO enabled.
../drivers/gpu/drm/i915/i915_pmu.c:116:3: error: call to '__compiletime_assert_487' declared with 'error' attribute: BUILD_BUG_ON failed: bit > BITS_PER_TYPE(typeof_member(struct i915_pmu, enable)) - 1
116 | BUILD_BUG_ON(bit >
| ^
Here is a way to reproduce the issue:
$ git checkout v6.15
$ mkdir build
$ ./scripts/kconfig/merge_config.sh -O build -n -m <(cat <<EOF
CONFIG_DRM=y
CONFIG_PCI=y
CONFIG_DRM_I915=y
CONFIG_PERF_EVENTS=y
CONFIG_DEBUG_FS=y
CONFIG_GCOV_KERNEL=y
CONFIG_GCOV_PROFILE_ALL=y
CONFIG_AUTOFDO_CLANG=y
EOF
)
$ PATH=${PATH}:${HOME}/llvm-20.1.5-x86_64/bin make LLVM=1 O=build \
olddefconfig
$ PATH=${PATH}:${HOME}/llvm-20.1.5-x86_64/bin make LLVM=1 O=build \
CLANG_AUTOFDO_PROFILE=...PATH_TO_SOME_AFDO_PROFILE... \
drivers/gpu/drm/i915/i915_pmu.o
Although not super sure what happened, by reviewing the code, it should
depend on `__builtin_constant_p(bit)` directly instead of assuming
`__builtin_constant_p(config)` makes `bit` a builtin constant.
Also fix a nit, to reuse the `bit` local variable.
Fixes: a644fde77f ("drm/i915/pmu: Change bitmask of enabled events to u32")
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Link: https://lore.kernel.org/r/20250612083023.562585-1-tzungbi@kernel.org
Using a string variable in place of a format string causes a W=1 build warning:
drivers/platform/x86/intel/uncore-frequency/uncore-frequency-common.c:61:40: error: format string is not a string literal (potentially insecure) [-Werror,-Wformat-security]
61 | length += sysfs_emit_at(buf, length, agent_name[agent]);
| ^~~~~~~~~~~~~~~~~
Use the safer "%s" format string to print it instead.
Fixes: b98fa870fc ("platform/x86/intel-uncore-freq: Add attributes to show agent types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20250610093459.2646337-1-arnd@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add Panther Lake support to Intel PMC SSRAM Telemetry driver.
Signed-off-by: Xi Pardee <xi.pardee@linux.intel.com>
Link: https://lore.kernel.org/r/20250610230416.622970-2-xi.pardee@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add Lunar Lake support to Intel PMC SSRAM Telemetry driver.
Signed-off-by: Xi Pardee <xi.pardee@linux.intel.com>
Link: https://lore.kernel.org/r/20250610230416.622970-1-xi.pardee@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add support for mana device level statistics.
Co-developed-by: Solom Tamawy <solom.tamawy@microsoft.com>
Signed-off-by: Solom Tamawy <solom.tamawy@microsoft.com>
Signed-off-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://patch.msgid.link/1749559717-3424-1-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This function has an array of eight mlx5_async_cmd structures, which
often fits on the stack, but depending on the configuration can
end up blowing the stack frame warning limit:
drivers/infiniband/hw/mlx5/devx.c:2670:6: error: stack frame size (1392) exceeds limit (1280) in 'mlx5_ib_ufile_hw_cleanup' [-Werror,-Wframe-larger-than]
Change this to a dynamic allocation instead. While a kmalloc()
can theoretically fail, a GFP_KERNEL allocation under a page will
block until memory has been freed up, so in the worst case, this
only adds extra time in an already constrained environment.
Fixes: 7c891a4dbc ("RDMA/mlx5: Add implementation for ufile_hw_cleanup device operation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250610092846.2642535-1-arnd@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
It can be known that the function “kfree” performs a null pointer check
for its input parameter.
It is therefore not needed to repeat such a check before its call.
Thus remove a redundant pointer check.
The source code was transformed by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patch.msgid.link/cdc577a5-cebd-404a-b762-cc6fee0870dc@web.de
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The 'error' variable is no longer needed,as iscsi_iser_mtask_xmit can
return the result of iser_send_control(conn,task) directly.
Signed-off-by: Li Jun <lijun01@kylinos.cn>
Link: https://patch.msgid.link/20250604102049.130039-1-lijun01@kylinos.cn
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
sizeof(xx) these variable values' return values cannot be 0.
For memory allocation requests of non-zero length,
there is no need to check other return values;
it is sufficient to only verify that it is not null.
Signed-off-by: luoqing <luoqing@kylinos.cn>
Link: https://patch.msgid.link/20250605034918.242682-1-l1138897701@163.com
Reviewed-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Calling ibv_advise_mr(3) with flags other than IBV_ADVISE_MR_FLAG_FLUSH
invokes an asynchronous request. It is best-effort, and thus can safely be
deferred to the system-wide workqueue.
The reference counter in rxe_mr is used to ensure that the MRs persist and
that rxe is not terminated until the queued work is done.
Signed-off-by: Daisuke Matsuda <dskmtsd@gmail.com>
Link: https://patch.msgid.link/20250522111955.3227-3-dskmtsd@gmail.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Minimal implementation of ibv_advise_mr(3) requires synchronous calls being
successful with the IBV_ADVISE_MR_FLAG_FLUSH flag. Asynchronous requests,
which are best-effort, will be supported subsequently.
Signed-off-by: Daisuke Matsuda <dskmtsd@gmail.com>
Link: https://patch.msgid.link/20250522111955.3227-2-dskmtsd@gmail.com
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Convert the I2C subsystem to drop using the 'master_'-prefixed callbacks
in favor of the simplified ones. Fix alignment of '=' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Some static strings have been stored in fixed char arrays although
they could be gracefully "const char *" instead. Also, a few other
definitions use the raw "char *" without const.
Converting those to "const char *" will save some memory and give more
safety, in addition to a side-effect to address the bogus compiler
warning with snprintf().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506121025.G9uunMlx-lkp@intel.com/
Link: https://patch.msgid.link/20250612064802.1170-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Fixes: 79d561c4ec ("ALSA: usb-audio: Add mixer quirk for Sony DualSense PS5")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20250612060228.1518028-1-nichen@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When porting a cma related usage from x86_64 server to arm64 server,
the "cma=4G@4G" setup failed on arm64. The reason is arm64 and some
other architectures have specific physical address limit for reserved
cma area, like 4GB due to the device's need for 32 bit dma. Actually
lots of platforms of those architectures don't have this device dma
limit, but still have to obey it, and are not able to reserve a huge
cma pool.
This situation could be improved by honoring the user input cma
physical address than the arch limit. As when users specify it, they
already knows what the default is which probably can't suit them.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Feng Tang <feng.tang@linux.alibaba.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250612021417.44929-1-feng.tang@linux.alibaba.com
After commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64 ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
init/main.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
init/initramfs.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
So fix these build warnings for the init code.
Link: https://lkml.kernel.org/r/20250608141235.155206-1-chenhuacai@loongson.cn
Fixes: a934a57a42 ("scripts/misc-check: check missing #include <linux/export.h> when W=1")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
