The $id value has a double "//". Drop it.
Fixes: 9ca5a7d9d2 ("dt-bindings: soc: fsl: Add fsl,ls1028a-reset for reset syscon node")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250507215903.2748698-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The incorrect PSP firmware size is used for initializing. It may
cause error for newer version firmware.
Fixes: 8c9ff1b181 ("accel/amdxdna: Add a new driver for AMD AI Engine")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://lore.kernel.org/r/20250604143217.1386272-1-lizhi.hou@amd.com
We are already prepared to define firmwares per-GT type, so we
should also prepare our messages to be GT-oriented.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250606204311.813-1-michal.wajdeczko@intel.com
When swiotlb buffer is full, the dma_map_sg() returns 0 to
msdc_prepare_data(), but it does not check it and sets the
MSDC_PREPARE_FLAG.
swiotlb_tbl_map_single() /* prints "swiotlb buffer is full" */
<-swiotlb_map()
<-dma_direct_map_page()
<-dma_direct_map_sg()
<-__dma_map_sg_attrs()
<-dma_map_sg_attrs()
<-dma_map_sg() /* returns 0 (pages mapped) */
<-msdc_prepare_data()
Then, the msdc_unprepare_data() checks MSDC_PREPARE_FLAG and calls
dma_unmap_sg() with unmapped pages. It causes a page fault.
To fix this problem, Do not set MSDC_PREPARE_FLAG if dma_map_sg()
fails because this is not prepared.
Fixes: 208489032b ("mmc: mediatek: Add Mediatek MMC driver")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Tested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/174908565814.4056588.769599127120955383.stgit@mhiramat.tok.corp.google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If spacemit_sdhci_get_clocks() fails, then propagate the error code.
Don't return success.
Fixes: e5502d15b0 ("mmc: sdhci-of-k1: add support for SpacemiT K1 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/aDVTtQdXVtRhxOrb@stanley.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the BROKEN_SD_DISCARD quirk for certain SanDisk SD cards from the
`mmc_blk_fixups[]` to `mmc_sd_fixups[]`. This ensures the quirk is
applied earlier in the device initialization process, aligning with the
reasoning in [1]. Applying the quirk sooner prevents the kernel from
incorrectly enabling discard support on affected cards during initial
setup.
[1] https://lore.kernel.org/all/20240820230631.GA436523@sony.com
Fixes: 07d2872bf4 ("mmc: core: Add SD card quirk for broken discard")
Signed-off-by: Avri Altman <avri.altman@sandisk.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250526114445.675548-1-avri.altman@sandisk.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert the MSIOF I2S driver to reuse the MSIOF register and register
bit definitions in the header file shared by the MSIOF SPI driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/754ed54057e54effd06143e71d6cd305c3334eca.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch modifies the assignment of machine structure pointers in the
acp_pci_probe function. Previously, the machine pointers were assigned
using the address-of operator (&), which caused incompatibility issues
in type assignments.
Additionally, the declarations of the machine arrays in amd.h have been
updated to reflect that they are indeed arrays (`[]`). The code is
further cleaned up by declaring the codec structures in
amd-acpi-mach.c as static, reflecting their intended usage.
error: symbol 'amp_rt1019' was not declared. Should it be static?
error: symbol 'amp_max' was not declared. Should it be static?
error: symbol 'snd_soc_acpi_amd_acp_machines' was not declared. Should it be static?
error: symbol 'snd_soc_acpi_amd_rmb_acp_machines' was not declared. Should it be static?
error: symbol 'snd_soc_acpi_amd_acp63_acp_machines' was not declared. Should it be static?
error: symbol 'snd_soc_acpi_amd_acp70_acp_machines' was not declared. Should it be static?
Fixes: 9c2c0ef640 ("ASoC: amd: acp: Fix snd_soc_acpi_mach id's duplicate symbol error")
Link: https://github.com/thesofproject/linux/issues/5438
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20250609121251.639080-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a safe guard in spi_offload_trigger to check the existence of
offload->ops before invoking the trigger_disable callback
Signed-off-by: Andres Urian Florez <andres.emb.sys@gmail.com>
Link: https://patch.msgid.link/20250608230422.325360-1-andres.emb.sys@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator for the 7" Raspberry Pi 720x1280 DSI panel based on ili9881.
This is the Raspberry Pi DSI Panel V2. The newer Raspberry Pi 5" and 7"
panels have a slightly different register map to the original one. Add a
new driver for this "regulator" chip, this time by exposing two GPIOs and
one PWM controller, both of which can be consumed by panel driver and
pwm-backlight respectively.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20250609000748.1665219-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Document regulator compatible string for the 7" Raspberry Pi 720x1280 DSI
panel based on ili9881. This is the Raspberry Pi DSI Panel V2. The newer
Raspberry Pi 5" and 7" panels have a slightly different register map to
the original one and offers PWM backlight control.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20250609000748.1665219-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a scripted split of the display related register macros from
i915_reg.h to display/intel_display_regs.h. As a starting point, move
all the macros that are only used in display code (or GVT). If there are
users in core i915 code or soc/, or no users anywhere, keep the macros
in i915_reg.h. This is done in groups of macros separated by blank
lines, moving the comments along with the groups.
Some manually picked macro groups are kept/moved regardless of the
heuristics above.
This is obviously a very crude approach. It's not perfect. But there are
4.2k lines in i915_reg.h, and its refactoring has ground to a halt. This
is the big hammer that splits the file to two, and enables further
cleanup.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> # v2
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250606102256.2080073-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As per the spec, one 32 bit reserved entry is missing here, add it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: 910cc1acc9 ("firmware: arm_ffa: Add support for passing UUID in FFA_MSG_SEND2")
Reviewed-by: Bertrand Marquis <bertrand.marquis@arm.com>
Message-Id: <28a624fbf416975de4fbe08cfbf7c2db89cb630e.1748948911.git.viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The notifier callback node allocation is currently done while holding
the notify_lock mutex. While this is safe even if memory allocation may
sleep, we need to move the allocation outside the locked region in
preparation to move from using muxtes to rwlocks.
Move the memory allocation to avoid potential sleeping in atomic context
once the locks are moved from mutex to rwlocks.
Fixes: e0573444ed ("firmware: arm_ffa: Add interfaces to request notification callbacks")
Message-Id: <20250528-ffa_notif_fix-v1-2-5ed7bc7f8437@arm.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit e0573444ed ("firmware: arm_ffa: Add interfaces to request
notification callbacks") adds support for notifier callbacks by allocating
and inserting a callback node into a hashtable during registration of
notifiers. However, during unregistration, the code only removes the
node from the hashtable without freeing the associated memory, resulting
in a memory leak.
Resolve the memory leak issue by ensuring the allocated notifier callback
node is properly freed after it is removed from the hashtable entry.
Fixes: e0573444ed ("firmware: arm_ffa: Add interfaces to request notification callbacks")
Message-Id: <20250528-ffa_notif_fix-v1-1-5ed7bc7f8437@arm.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The touch panel display is an optional add on for the RockPro64
so this should be an DT overlay, drop the panel options in
preparation to add this as an overlay.
This effectively reverts commit b65155c786 so as to add an
overlay for it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20250518215944.178582-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
IS_REACHABLE() was required when CONFIG_HWMON was set to m and HSMP to y.
However, commit 69157b00b5 ("platform/x86/amd/hsmp: fix building with
CONFIG_HWMON=m") added a HWMON dependency for HSMP in Kconfig. With
this change, using IS_ENABLED() is sufficient.
Add the missing header file as well.
Signed-off-by: Suma Hegde <suma.hegde@amd.com>
Link: https://lore.kernel.org/r/20250603055807.2503028-1-suma.hegde@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add known fan type IDs and match them to an appropriate label in
awcc_hwmon_read_string().
Additionally, add the AWCC_TEMP_SENSOR_FRONT type, which was inferred
from it's related fan type in supported systems.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250528-awcc-labels-v1-1-6aa39d8e4c3d@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Replace deprecated snps,reset-gpio, snps,reset-active-low, and
snps,reset-delays-us in gmac0 and gmac1 nodes with standard reset-gpios,
reset-assert-us, and reset-deassert-us in rgmii_phy0 and rgmii_phy1 nodes.
Add pinctrl properties to PHY nodes and define gmac0_rst and gmac1_rst in
pinctrl node. Reorder phy-handle for consistency.
Signed-off-by: John Clark <inindev@gmail.com>
Link: https://lore.kernel.org/r/20250520003332.163124-2-inindev@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RADXA ROCK 5T is a single board computer quite similar to the ROCK
5B+, except it has one more PCIe-to-Ethernet controller (at the expense
of a USB3 port) and a barrel jack for power input instead. Some pins are
shuffled around as well.
Add a device tree for it.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250520-add-rock5t-v2-4-1f1971850a20@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few device tree nodes are shared between ROCK 5B and ROCK 5B+ that are
not shared with ROCK 5T.
Move them into their own device tree include.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250520-add-rock5t-v2-3-1f1971850a20@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As subsequent patches will add ROCK 5T support, rename the .dtsi file to
reflect that it's shared between ROCK 5B, ROCK 5B+ and ROCK 5T.
This is done separately from moving the 5B and 5B+ only nodes to a
common tree so that the history stays bisectable and the diff easily
reviewable.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250520-add-rock5t-v2-2-1f1971850a20@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RADXA ROCK 5T is a single board computer aimed at industrial use.
Its design is similar to the ROCK 5B+, but it does away with one of the
USB-C PD inputs, and uses one combination USB3/SATA/PCIe PHY for an
additional second 2.5G PCIe network card instead of USB3.
Link: https://radxa.com/products/rock5/5t/
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250520-add-rock5t-v2-1-1f1971850a20@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add vendor prefix for SakuraPi.org, which produces
development boards like the SakuraPi-RK3308B.
Link: https://docs.sakurapi.org
Signed-off-by: Hsun Lai <i@chainsx.cn>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250521131108.5710-2-i@chainsx.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-2-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 791c154c39 ("arm64: dts: rockchip: Add support for rk3588 based board Cool Pi CM5 EVB")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SW_MACHINE_COVER switch event was added to input event codes to
detect the removal of the back cover of the N900.
But on the PineNote its purpose is to detect when the front cover gets
closed, just like when a laptop lid is closed. Therefore SW_LID is the
appropriate linux code and not SW_MACHINE_COVER.
Reported-by: hrdl <git@hrdl.eu>
Helped-by: phantomas <phantomas@phantomas.xyz>
Link: https://lore.kernel.org/r/270f27c9-afd6-171d-7dce-fe1d71dd8f9a@wizzup.org/
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250526161506.139028-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
For the RK3588 HDMI controller, the falling edge of DDC SDA and SCL
almost coincide and cannot be adjusted by HDMI registrer, resulting
in poor compatibility of DDC communication.
An improvement of the compatibility of DDC can be done by increasing
the driver strength of SCL and decreasing the driver strength of SDA
to increase the slope of the falling edge.
It should be noted that the maximum driving strength of hdmim0_tx1_scl
is only 3, which is different from that of the other IOs.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250522020537.1884771-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie0 already used 0 as its pci-domain, so pcie1 will fail to
allocate the same pci-domain if both of them are used.
rk-pcie 2a210000.pcie: PCIe Link up, LTSSM is 0x130011
rk-pcie 2a210000.pcie: PCIe Gen.2 x1 link up
rk-pcie 2a210000.pcie: Scanning root bridge failed
rk-pcie 2a210000.pcie: failed to initialize host
Fixes: d4b9fc2af4 ("arm64: dts: rockchip: Add rk3576 pcie nodes")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1748918140-212263-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update the i2c1 bus noting that the unknown/unused device at 0x3c is an
iSmartWare SW2001 "encryption IC".
Based on the documentation I was able to find, this IC appears to be
used to authenticate a device for certain programs to ensure they only
run on authorized devices as a form of digital rights management.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20250604024119.381337-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the Ethernet Switch adapter connected to the
mezzanine connector on RK3588 Jaguar.
This adapter has a KSZ9896 Ethernet Switch with 4 1GbE Ethernet
connectors, two user controllable LEDs, and an M12 12-pin connector
which exposes the following signals:
- RS232/RS485 (max 250Kbps/500Kbps, RX pin1, TX pin2)
- two digital inputs (pin4 routed to GPIO3_C5 on SoC, pin5 to GPIO4_B4)
- two digital outputs (pin7 routed to GPIO3_D3 on SoC, pin8 to
GPIO3_D1)
- two analog inputs (pin10 to channel1 of ADS1015, pin11 to channel2)
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
[Andrew's review for gmac1 and switch@5f parts]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20250604-jaguar-mezz-eth-switch-v3-1-c68123240f9e@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the DSI controller, DSI DCPHY, and Huiling hl055fhav028c
1080x1920 panel for the Gameforce Ace.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250603193930.323607-5-macroalpha82@gmail.com
[moved lcd_rst pin into a lcd pinctrl group with lcd_bl_en]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a function to init ggtt for kunit, and use the GGTT function for
initialising the GGTT node without populating it. This
prevents the test from ever knowing about struct xe_ggtt.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-11-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Split the GGTT PTE readout to a separate function, this is useful for
adding testcases in the next commit, and also cleaner than manually
reading out GGTT.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-10-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The users inside display have been converted to use thepte_encode_flags
callback, we can now remove the pte_encode_bo cb.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-9-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
For DPT, it is sufficient to get the GGTT encode flags to fill the DPT.
Create a function to return the encode flags, and then encode using the
BO address.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-7-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Pinning large linear display framebuffers is becoming a bottleneck.
My plan of attack is doing a custom walk over the BO, this allows for
easier optimization of consecutive entries.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-6-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Obtain the id from the root tile. Likely this can be hardcoded to 0,
but use the clean solution of obtaining root id and doing that.
to_xe_device(ggtt->tile) can also be easily replaced with xe.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-5-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Instead of allocating inside xe_tile, create a new function that returns
an allocated struct xe_ggtt from xe_ggtt.c
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-4-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Another requirement of hiding more of struct xe_ggtt.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-3-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
This is the first step to hide the details of struct xe_ggtt.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF warning:
pinctrl-tb10x.c:815:34: warning: unused variable 'tb10x_pinctrl_dt_ids' [-Wunused-const-variable]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505301317.EI1caRC0-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250601105100.27927-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
