BD96802Qxx-C is an automotive grade configurable Power Management
Integrated Circuit supporting Functional Safety features for application
processors, SoCs and FPGAs. BD96802 is controlled via I2C, provides two
interrupt lines and has two controllable buck regulators.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/ed55edffca3b0a2d7e8bcd9ebd8d8abd9a9b7dfe.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
BD96802Qxx-C is an automotive grade configurable Power Management
Integrated Circuit supporting Functional Safety features for application
processors, SoCs and FPGAs. BD96802 is controlled via I2C, provides two
interrupt lines and has two controllable buck regulators.
The BD96802 belongs to the family of ROHM Scalable PMICs and is intended
to be used as a companion PMIC for the BD96801.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/df7983e7c623041f14a4fbe409a2cff846e68a05.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
kvm_arch_has_irq_bypass() is a small function and even though it does
not appear in any *really* hot paths, it's also not entirely rare.
Make it inline---it also works out nicely in preparation for using it in
kvm-intel.ko and kvm-amd.ko, since the function is not currently exported.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Loading a driver just to configure blk-cgroup doesn't make sense, as that
assumes and already existing device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250423053810.1683309-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkdev_get_no_open can trigger the legacy autoload of block drivers. A
simple stat of a block device has not historically done that, so disable
this behavior again.
Fixes: 9abcfbd235 ("block: Add atomic write support for statx")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250423053810.1683309-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
backing_inode is only used once, so remove it and update the comment
describing the bdev lookup to be a bit more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250423053810.1683309-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These are only to be used by block internal code. Remove the comment
as we grew more users due to reworking block device node opening.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250423053810.1683309-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the user increased the read-ahead size through sysfs this value
currently get lost if the device is reprobe, including on a resume
from suspend.
As there is no hardware limitation for the read-ahead size there is
no real need to reset it or track a separate hardware limitation
like for max_sectors.
This restores the pre-atomic queue limit behavior in the sd driver as
sd did not use blk_queue_io_opt and thus never updated the read ahead
size to the value based of the optimal I/O, but changes behavior for
all other drivers. As the new behavior seems useful and sd is the
driver for which the readahead size tweaks are most useful that seems
like a worthwhile trade off.
Fixes: 804e498e04 ("sd: convert to the atomic queue limits API")
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20250424082521.1967286-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Adding support for the dummy sequence configuration. The dummy sequence
introduces a delay between the command and the data phases of a
transfer. This delay, measured in clock cycles, allows the slave
device to prepare for data transmission, ensuring data integrity and
proper synchronization.
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-6-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the chip select (CS) deactivation and inter-transfer delay
execution only during the DATA_TRANSFER phase when the cs_change
flag is not set. This ensures proper CS handling and timing between
transfers while eliminating redundant operations.
Fixes: 1b8342cc4a ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-4-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unnecessary error handling code that terminated transfers and
executed delay on errors. This code was redundant as error handling is
already done at a higher level in the SPI core.
Fixes: 1b8342cc4a ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-3-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch corrects the QSPI_COMMAND_X1_X2_X4 and QSPI_ADDRESS_X1_X2_X4
macros to properly encode the bus width for x1, x2, and x4 transfers.
Although these macros were previously incorrect, they were not being
used in the driver, so no functionality was affected.
The patch updates tegra_qspi_cmd_config() and tegra_qspi_addr_config()
function calls to use the actual bus width from the transfer, instead of
hardcoding it to 0 (which implied x1 mode). This change enables proper
support for x1, x2, and x4 data transfers by correctly configuring the
interface width for commands and addresses.
These modifications improve the QSPI driver's flexibility and prepare it
for future use cases that may require different bus widths for commands
and addresses.
Fixes: 1b8342cc4a ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-2-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the first frame in "repeat-mode" is the pattern, the pattern done
interrupt is ignored by the driver. With small resolution bitstreams,
the interrupts might fire too quickly and hardware combine two irqs to
once because irq handle have latency. Thus the driver might miss the
frame decode done interrupt from the first actual frame.
In order to avoid the driver wait for the frame done interrupt that has
been combined to the pattern done interrupt and been ignored, driver
will check the curr_desc and slot_status registers to figure out if the
decoding of actual frame is finished or not.
Firstly we check the curr_desc register,
- if it is still pointing to the pattern descriptor, the second actual
frame is not started, we can wait for its frame-done interrupt.
- if the curr_desc has pointed to the frame descriptor, then we check the
ongoing bit of slot_status register.
- if the ongoing bit is set to 1, the decoding of the actual frame is not
finished, we can wait for its frame-done interrupt.
- if the ongoing bit is set to 0, the decoding of the actual frame is
finished, we can't wait for the second interrupt, but mark it as done.
But there is still a small problem, that the curr_desc and slot_status
registers are not synchronous. curr_desc is updated when the
next_descpt_ptr is loaded, but the ongoing bit of slot_status is set
after the 32 bytes descriptor is loaded, there will be a short time
interval in between, which may cause fake false. Consider read register
is quite slow compared with IP read 32byte from memory, read twice
slot_status can avoid this situation.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
In order to decode a motion-jpeg bitstream, which doesn't provide a DHT,
the driver will first decode a pattern jpeg and use the DHT found in the
pattern to decode the first actual frame. This mode is called
"repeat-mode" and it utilizes linked descriptors.
The smallest supported resolution of 64x64 was used for that pattern to
not cause unneeded performance delay. This choice, however, can cause a
corrupted decoded picture of the first frame after the pattern, when the
resolution of that frame is larger than the pattern and is not aligned
to 64.
By altering the pattern size to 128x64, this corruption can be avoided.
That size has been confirmed to be safe by the hardware designers.
Additionally, a DMA buffer needs to be allocated to store the decoded
picture of the pattern image.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When allocation failures are not cleaned up by the driver, further
allocation errors will be false-positives, which will cause buffers to
remain uninitialized and cause NULL pointer dereferences.
Ensure proper cleanup of failed allocations to prevent these issues.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Ensure that the slot data pointers are reset to NULL and handles are
set to 0 after freeing the coherent memory. This makes he function
mxc_jpeg_alloc_slot_data() and mxc_jpeg_free_slot_data() safe to be
called multiple times.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Move function mxc_jpeg_free_slot_data() above mxc_jpeg_alloc_slot_data()
allowing to call that function during allocation failures.
No functional changes are made.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add video_device_release() to release the memory allocated by
video_device_alloc() if something goes wrong.
Fixes: a1e2940458 ("media: imagination: Add E5010 JPEG Encoder driver")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
"vpu_core->msg_buffer_size" is unused out-side of vpu_core_register().
There is no need to save this value in struct vpu_core.
Remove it and use a local variable instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This is a "customer" format, though on Rockchip RK3588 it has been
verified to be NV15 format, which matches what the GPU and display
handles has 10bit pixel formats.
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When an output buffer contains error frame header,
v4l2_jpeg_parse_header() will return error, then driver will mark this
buffer and a capture buffer done with error flag in device_run().
But if the error occurs in the first frames, before setup the capture
queue, there is no chance to schedule device_run(), and there may be no
capture to mark error.
So we need to drop this buffer with error flag, and make the decoding
can continue.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Mediatek devices that support HEVC also support the main still picture
profile, but today, the main still picture profile is excluded.
This removes the skip mask for HEVC, and enables the main still
picture profile decoding.
Signed-off-by: Nathan Hebert <nhebert@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Debug log when remapping a pin/function because of a int3472_gpio_map[]
match.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-10-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
New Intel Meteor Lake based laptops with IPU6 cameras have a new type 0x12
pin defined in the INT3472 sensor companion device which describes
the sensor's GPIOs.
This pin is primarily used on designs with a Lattice FPGA chip which is
capable of running the sensor independently of the main CPU for features
like presence detection. This pin needs to be driven high to make the FPGA
run the power-on sequence of the sensor. After driving the pin high,
the FPGA "firmware" needs 25ms to complete the power-on sequence.
Add support for this modelling the handshake pin as a GPIO driven "dvdd"
regulator with a 25 ms enable time. This model was chosen because:
1. Sensor chips don't have a handshake pin, so we need to abstract this
in some way which does not require modification to the sensor drivers,
sensor drivers using the bulk-regulator API to get avdd + vddio + dvdd
is normal. So this will work to get the right value set to the handshake
pin without requiring sensor driver modifications.
2. Sensors typically wait only a small time for the sensor to power-on
after de-asserting reset. Not the 25ms the Lattice chip requires.
Using the regulator framework's enable_time allows hiding the need for
this delay from the sensor drivers.
Link: https://lore.kernel.org/platform-driver-x86/59f672c3-6d87-4ec7-9b7f-f44fe2cce934@redhat.com/
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2341731
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-9-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Prepare the discrete code for registering more than 1 GPIO regulator.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-8-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Avoid the GPIO controlling the avdd regulator being driven low or high
for a very short time leading to spikes by adding an enable delay of 2 ms
and a minimum off to on delay of also 2 ms.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-7-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
This is a preparation patch for registering multiple regulators, which
requires a different supply-name for each regulator. Make supply-name
a parameter to skl_int3472_register_regulator() and use con-id to set it
so that the existing int3472_gpio_map remapping can be used with it.
Since supply-name is a parameter now, drop the fixed
skl_int3472_regulator_map_supplies[] array and instead add lower- and
upper-case mappings of the passed-in supply-name to the regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-6-hdegoede@redhat.com
[ij: GPIO_SUPPPLY_NAME_LENGTH -> GPIO_SUPPLY_NAME_LENGTH]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Rework the discrete quirk handling to use a quirks struct which is
pointed to by a dmi_system_id table, rather then having a dmi_system_id
table per type of quirk.
This is a preparation patch for adding support for multiple regulators,
where not all regulators might be shared between sensors.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-5-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The gpio field in struct int3472_gpio_regulator is only briefly used to
store the GPIO in skl_int3472_register_regulator(). Instead just store
the GPIO directly into cfg.ena_gpiod an drop the gpio field.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The supply_name field is not mandatory and is supposed to be set to
the name of another regulator when it is known that the regulator being
registered is supplied by that other regulator.
Having a regulator supplying the regulator which is being registered does
not apply to the INT3472 GPIO regulator, stop setting a supply_name.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
skl_int3472_register_dsm_clock() and skl_int3472_register_gpio_clock() are
80% the same code. Factor out the common code into a new
skl_int3472_register_clock() helper.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: David Heidelberg <david@ixit.cz> # Dell Latitude 9440
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417111337.38142-2-hdegoede@redhat.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Enabling the compile test should not cause automatic enabling of all
drivers, but only allow to choose to compile them.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250417074648.81528-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Use a faux device parent for registering the platform_profile instead of
a "fake" platform device.
The faux bus is a minimalistic, single driver bus designed for this
purpose.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250411-dell-faux-v1-3-ea1f1c929b7e@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The choices bitmap belongs only to this thread, therefore we can use the
non-atomic version of set_bit().
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250411-dell-faux-v1-2-ea1f1c929b7e@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The dell-pc module only supports the thermal management Dell SMBIOS
feature, therefore it is pointless to have it loaded if this is not
available.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250411-dell-faux-v1-1-ea1f1c929b7e@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Remove two trivial but long unused functions.
__round_jiffies() has been unused since 2008's
commit 9c133c469d ("Add round_jiffies_up and related routines")
__round_jiffies_up() has been unused since 2019's
commit 7ae3f6e130 ("powerpc/watchdog: Use hrtimers for per-CPU
heartbeat")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250418200803.427911-1-linux@treblig.org
Some distributions, such as centos stream 9, still have a version of
coreutils which does not yet support the %Hr and %Lr formats for stat(1)
[1, 2]. Running ublk selftests on these distributions results in the
following error in tests that use the _get_disk_dev_t helper:
line 23: ?r: syntax error: operand expected (error token is "?r")
To better accommodate older distributions, rewrite _get_disk_dev_t to
use the much older %t and %T formats for stat instead.
[1] https://github.com/coreutils/coreutils/blob/v9.0/NEWS#L114
[2] https://pkgs.org/download/coreutils
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250423-ublk_selftests-v1-2-7d060e260e76@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A DRM File is the DRM counterpart to a kernel file structure,
representing an open DRM file descriptor.
Add a Rust abstraction to allow drivers to implement their own File types
that implement the DriverFile trait.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20250410235546.43736-7-dakr@kernel.org
[ Rework of drm::File
* switch to the Opaque<T> type
* fix (mutable) references to struct drm_file (which in this context
is UB)
* restructure and rename functions to align with common kernel
schemes
* write and fix safety and invariant comments
* remove necessity for and convert 'as' casts
* original source archive: https://archive.is/GH8oy
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Implement the DRM driver `Registration`.
The `Registration` structure is responsible to register and unregister a
DRM driver. It makes use of the `Devres` container in order to allow the
`Registration` to be owned by devres, such that it is automatically
dropped (and the DRM driver unregistered) once the parent device is
unbound.
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20250410235546.43736-6-dakr@kernel.org
[ Rework of drm::Registration
* move VTABLE to drm::Device to prevent use-after-free bugs; VTABLE
needs to be bound to the lifetime of drm::Device, not the
drm::Registration
* combine new() and register() to get rid of the registered boolean
* remove file_operations
* move struct drm_device creation to drm::Device
* introduce Devres
* original source archive: https://archive.is/Pl9ys
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Implement the abstraction for a `struct drm_device`.
A `drm::Device` creates a static const `struct drm_driver` filled with
the data from the `drm::Driver` trait implementation of the actual
driver creating the `drm::Device`.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20250410235546.43736-5-dakr@kernel.org
[ Rewrite of drm::Device
* full rewrite of the drm::Device abstraction using the subclassing
pattern
* original source archive: http://archive.today/5NxBo
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Let's use the pci/platform-specialized functions for mapping a resource,
and pass the mapped address to intel_spi_probe. Benefits are:
- No separate call needed for getting the resource, and no access to
struct pci_dev internals (pdev->resource[]).
- More user-friendly output in /proc/iomem. In my case:
before
80704000-80704fff : 0000:00:1f.5
80704000-80704fff : 0000:00:1f.5 0000:00:1f.5
after
80704000-80704fff : 0000:00:1f.5
80704000-80704fff : spi_intel_pci
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/2585fa05-60c4-48c4-a838-e87014665ae2@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas MSIOF (Clock-Synchronized Serial Interface with FIFO) can work as
both SPI and I2S. MSIOF-I2S will use Audio Graph Card/Card2 driver which
Of-Graph in DT.
MSIOF-SPI/I2S are using same DT compatible properties.
MSIOF-I2S uses Of-Graph for Audio-Graph-Card/Card2,
MSIOF-SPI doesn't use Of-Graph.
Check "port" node when driver probing
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/87wmbi2x0g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sh_msiof_spi_probe() is using priv->dev everywhere,
but it makes code long. Create struct device *dev and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/87y0vy2x0o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://patch.msgid.link/20250424010855.2662-1-liubo03@inspur.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the references to Cirrus Logic files under include/sound to be a
wildcard of all cs* and use X: to exclude the three cs* files that are not
related to ASoC.
This means that new Cirrus Logic files added to include/sound will be
picked up automatically as an ASoC file without any changes to MAINTAINERS.
New files are most likely to be for ASoC drivers now.
It's also easier to manage than ranges of wildcarding for different sets of
files.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250423192714.22158-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
