Arch-PEBS retires IA32_PEBS_ENABLE and MSR_PEBS_DATA_CFG MSRs, so
intel_pmu_pebs_enable/disable() and intel_pmu_pebs_enable/disable_all()
are not needed to call for ach-PEBS.
To make the code cleaner, introduce static calls
x86_pmu_pebs_enable/disable() and x86_pmu_pebs_enable/disable_all()
instead of adding "x86_pmu.arch_pebs" check directly in these helpers.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-7-dapeng1.mi@linux.intel.com
Since architectural PEBS would be introduced in subsequent patches,
rename x86_pmu.pebs to x86_pmu.ds_pebs for distinguishing with the
upcoming architectural PEBS.
Besides restrict reserve_ds_buffers() helper to work only for the
legacy DS based PEBS and avoid it to corrupt the pebs_active flag and
release PEBS buffer incorrectly for arch-PEBS since the later patch
would reuse these flags and alloc/release_pebs_buffer() helpers for
arch-PEBS.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-6-dapeng1.mi@linux.intel.com
Move x86_pmu.bts flag initialization into bts_init() from
intel_ds_init() and rename intel_ds_init() to intel_pebs_init() since it
fully initializes PEBS now after removing the x86_pmu.bts
initialization.
It's safe to move x86_pmu.bts into bts_init() since all x86_pmu.bts flag
are called after bts_init() execution.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-5-dapeng1.mi@linux.intel.com
CPUID archPerfmonExt (0x23) leaves are supported to enumerate CPU
level's PMU capabilities on non-hybrid processors as well.
This patch supports to parse archPerfmonExt leaves on non-hybrid
processors. Architectural PEBS leverages archPerfmonExt sub-leaves 0x4
and 0x5 to enumerate the PEBS capabilities as well. This patch is a
precursor of the subsequent arch-PEBS enabling patches.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-4-dapeng1.mi@linux.intel.com
From the PMU's perspective, Clearwater Forest is similar to the previous
generation Sierra Forest.
The key differences are the ARCH PEBS feature and the new added 3 fixed
counters for topdown L1 metrics events.
The ARCH PEBS is supported in the following patches. This patch provides
support for basic perfmon features and 3 new added fixed counters.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-3-dapeng1.mi@linux.intel.com
Due to an oversight in merging:
da916e96e2 ("perf: Make perf_pmu_unregister() useable")
on top of:
a3c3c66670 ("perf/core: Fix child_total_time_enabled accounting bug at task exit")
the timekeeping fix from this latter patch got undone.
Redo it.
Fixes: da916e96e2 ("perf: Make perf_pmu_unregister() useable")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250417080815.GI38216@noisy.programming.kicks-ass.net
Due to an oversight in merging:
da916e96e2 ("perf: Make perf_pmu_unregister() useable")
on top of:
56799bc035 ("perf: Fix hang while freeing sigtrap event")
.. it is now possible to hit put_event(EVENT_TOMBSTONE), which makes
the computer sad.
This also means that for the event->parent == EVENT_TOMBSTONE, the
put_event() matching inherit_event() has gone missing.
Previously this was done in perf_event_release_kernel() after calling
perf_remove_from_context(), but with it delegated to put_event(), this
case is now entirely missed, leading to leaks.
Fixes: da916e96e2 ("perf: Make perf_pmu_unregister() useable")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: kernel test robot <oliver.sang@intel.com>
Tested-by: James Clark <james.clark@linaro.org>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Closes: https://lore.kernel.org/oe-lkp/202504131701.941039cd-lkp@intel.com
Link: https://lkml.kernel.org/r/20250415131446.GN5600@noisy.programming.kicks-ass.net
So there are three situations:
* If perf_event_free_task() has removed all the children from the parent list
before perf_event_release_kernel() got a chance to even iterate them, then
it's all good as there is no get_ctx() pending.
* If perf_event_release_kernel() iterates a child event, but it gets freed
meanwhile by perf_event_free_task() while the mutexes are temporarily
unlocked, it's all good because while locking again the ctx mutex,
perf_event_release_kernel() observes TASK_TOMBSTONE.
* But if perf_event_release_kernel() frees the child event before
perf_event_free_task() got a chance, we may face this scenario:
perf_event_release_kernel() perf_event_free_task()
-------------------------- ------------------------
mutex_lock(&event->child_mutex)
get_ctx(child->ctx)
mutex_unlock(&event->child_mutex)
mutex_lock(ctx->mutex)
mutex_lock(&event->child_mutex)
perf_remove_from_context(child)
mutex_unlock(&event->child_mutex)
mutex_unlock(ctx->mutex)
// This lock acquires ctx->refcount == 2
// visibility
mutex_lock(ctx->mutex)
ctx->task = TASK_TOMBSTONE
mutex_unlock(ctx->mutex)
wait_var_event()
// enters prepare_to_wait() since
// ctx->refcount == 2
// is guaranteed to be seen
set_current_state(TASK_INTERRUPTIBLE)
smp_mb()
if (ctx->refcount != 1)
schedule()
put_ctx()
// NOT fully ordered! Only RELEASE semantics
refcount_dec_and_test()
atomic_fetch_sub_release()
// So TASK_TOMBSTONE is not guaranteed to be seen
if (ctx->task == TASK_TOMBSTONE)
wake_up_var()
Basically it's a broken store buffer:
perf_event_release_kernel() perf_event_free_task()
-------------------------- ------------------------
ctx->task = TASK_TOMBSTONE smp_store_release(&ctx->refcount, ctx->refcount - 1)
smp_mb()
READ_ONCE(ctx->refcount) READ_ONCE(ctx->task)
So we need a smp_mb__after_atomic() before looking at ctx->task.
Fixes: 59f3aa4a3e ("perf: Simplify perf_event_free_task() wait")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/Z_ZvmEhjkAhplCBE@localhost.localdomain
In the zeal to adjust all event->state checks to include the new
REVOKED state, one adjustment was made in error. Notably it resulted
in read() on the perf filedesc to stop working for any state lower
than ERROR, specifically EXIT.
This leads to problems with (among others) perf-stat, which wants to
read the counts after a program has finished execution.
Fixes: da916e96e2 ("perf: Make perf_pmu_unregister() useable")
Reported-by: "Mi, Dapeng" <dapeng1.mi@linux.intel.com>
Reported-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/77036114-8723-4af9-a068-1d535f4e2e81@linaro.org
Link: https://lore.kernel.org/r/20250417080725.GH38216@noisy.programming.kicks-ass.net
io_import_fixed is a mess. Even though we know the final len of the
iterator, we still assign offset + len and do some magic after to
correct for that.
Do offset calculation first and finalise it with iov_iter_bvec at the
end.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/2d5107fed24f8b23245ef2ede9a5a7f7c426df61.1744882081.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kernel registered buffers are special because segments are not uniform
in size, and we have a bunch of optimisations based on that uniformity
for normal buffers. Handle kbuf separately, it'll be cleaner this way.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/4e9e5990b0ab5aee723c0be5cd9b5bcf810375f9.1744882081.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Don't optimise for requests with offset=0. Large registered buffers are
the preference and hence the user is likely to pass an offset, and the
adjustments are not expensive and will be made even cheaper in following
patches.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/1c2beb20470ee3c886a363d4d8340d3790db19f3.1744882081.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
From PMU's perspective, Panther Lake is similar to the previous
generation Lunar Lake. Both are hybrid platforms, with e-core and
p-core.
The key differences are the ARCH PEBS feature and several new events.
The ARCH PEBS is supported in the following patches.
The new events will be supported later in perf tool.
Share the code path with the Lunar Lake. Only update the name.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20250415114428.341182-2-dapeng1.mi@linux.intel.com
Currently when a user samples user space GPRs (--user-regs option) with
PEBS, the user space GPRs actually always come from software PMI
instead of from PEBS hardware. This leads to the sampled GPRs to
possibly be inaccurate for single PEBS record case because of the
skid between counter overflow and GPRs sampling on PMI.
For the large PEBS case, it is even worse. If user sets the
exclude_kernel attribute, large PEBS would be used to sample user space
GPRs, but since PEBS GPRs group is not really enabled, it leads to all
samples in the large PEBS record to share the same piece of user space
GPRs, like this reproducer shows:
$ perf record -e branches:pu --user-regs=ip,ax -c 100000 ./foo
$ perf report -D | grep "AX"
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
.... AX 0x000000003a0d4ead
So enable GPRs group for user space GPRs sampling and prioritize reading
GPRs from PEBS. If the PEBS sampled GPRs is not user space GPRs (single
PEBS record case), perf_sample_regs_user() modifies them to user space
GPRs.
[ mingo: Clarified the changelog. ]
Fixes: c22497f583 ("perf/x86/intel: Support adaptive PEBS v4")
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250415104135.318169-2-dapeng1.mi@linux.intel.com
The below code would always unconditionally clear other status bits like
perf metrics overflow bit once PEBS buffer overflows:
status &= intel_ctrl | GLOBAL_STATUS_TRACE_TOPAPMI;
This is incorrect. Perf metrics overflow bit should be cleared only when
fixed counter 3 in PEBS counter group. Otherwise perf metrics overflow
could be missed to handle.
Closes: https://lore.kernel.org/all/20250225110012.GK31462@noisy.programming.kicks-ass.net/
Fixes: 7b2c05a15d ("perf/x86/intel: Generic support for hardware TopDown metrics")
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250415104135.318169-1-dapeng1.mi@linux.intel.com
- fix scan failure for non-ANA multipath controllers (Hannes Reinecke)
- fix multipath sysfs links creation for some cases (Hannes Reinecke)
- PCIe endpoint fixes (Damien Le Moal)
- use NULL instead of 0 in the auth code (Damien Le Moal)
-----BEGIN PGP SIGNATURE-----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=ZSJ5
-----END PGP SIGNATURE-----
Merge tag 'nvme-6.15-2025-04-17' of git://git.infradead.org/nvme into block-6.15
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.15
- fix scan failure for non-ANA multipath controllers (Hannes Reinecke)
- fix multipath sysfs links creation for some cases (Hannes Reinecke)
- PCIe endpoint fixes (Damien Le Moal)
- use NULL instead of 0 in the auth code (Damien Le Moal)"
* tag 'nvme-6.15-2025-04-17' of git://git.infradead.org/nvme:
nvmet: pci-epf: cleanup link state management
nvmet: pci-epf: clear CC and CSTS when disabling the controller
nvmet: pci-epf: always fully initialize completion entries
nvmet: auth: use NULL to clear a pointer in nvmet_auth_sq_free()
nvme-multipath: sysfs links may not be created for devices
nvme: fixup scan failure for non-ANA multipath controllers
Use the generic boolean device property getter instead of the
OF-specific variant. This allows us to stop pulling in linux/of.h. While
at it: drop the of_irq.h inclusion as none of its symbols are used in
this driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nikolaos Pasaloukos <nikolaos.pasaloukos@blaize.com>
Link: https://lore.kernel.org/r/20250408143629.125576-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This is already done by the gpio-regmap abstraction by calling
gpiochip_get_ngpios(). We don't need to do this at the driver level.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpio-regmap-ngpios-v2-1-26f254014f57@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-gpio-part1-v1-12-78399683ca38@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-gpio-part1-v1-10-78399683ca38@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-gpio-part1-v1-8-78399683ca38@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-gpio-part1-v1-7-78399683ca38@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-gpio-part1-v1-6-78399683ca38@linaro.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
We've never supported StreamID aliasing between devices, and as such
they will never have had functioning DMA, but this is not fatal to the
SMMU itself. Although aliasing between hard-wired platform device
StreamIDs would tend to raise questions about the whole system, in
practice it's far more likely to occur relatively innocently due to
legacy PCI bridges, where the underlying StreamID mappings are still
perfectly reasonable.
As such, return a more benign -ENODEV when failing probe for such an
unsupported device (and log a more obvious error message), so that it
doesn't break the entire SMMU probe now that bus_iommu_probe() runs in
the right order and can propagate that error back. The end result is
still that the device doesn't get an IOMMU group and probably won't
work, same as before.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/39d54e49c8476efc4653e352150d44b185d6d50f.1744380554.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
ASPEED VGA card has two built-in devices:
0008:06:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 06)
0008:07:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 52)
Its toplogy looks like this:
+-[0008:00]---00.0-[01-09]--+-00.0-[02-09]--+-00.0-[03]----00.0 Sandisk Corp Device 5017
| +-01.0-[04]--
| +-02.0-[05]----00.0 NVIDIA Corporation Device
| +-03.0-[06-07]----00.0-[07]----00.0 ASPEED Technology, Inc. ASPEED Graphics Family
| +-04.0-[08]----00.0 Renesas Technology Corp. uPD720201 USB 3.0 Host Controller
| \-05.0-[09]----00.0 Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
\-00.1 PMC-Sierra Inc. Device 4028
The IORT logic populaties two identical IDs into the fwspec->ids array via
DMA aliasing in iort_pci_iommu_init() called by pci_for_each_dma_alias().
Though the SMMU driver had been able to handle this situation since commit
563b5cbe33 ("iommu/arm-smmu-v3: Cope with duplicated Stream IDs"), that
got broken by the later commit cdf315f907 ("iommu/arm-smmu-v3: Maintain
a SID->device structure"), which ended up with allocating separate streams
with the same stuffing.
On a kernel prior to v6.15-rc1, there has been an overlooked warning:
pci 0008:07:00.0: vgaarb: setting as boot VGA device
pci 0008:07:00.0: vgaarb: bridge control possible
pci 0008:07:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
pcieport 0008:06:00.0: Adding to iommu group 14
ast 0008:07:00.0: stream 67328 already in tree <===== WARNING
ast 0008:07:00.0: enabling device (0002 -> 0003)
ast 0008:07:00.0: Using default configuration
ast 0008:07:00.0: AST 2600 detected
ast 0008:07:00.0: [drm] Using analog VGA
ast 0008:07:00.0: [drm] dram MCLK=396 Mhz type=1 bus_width=16
[drm] Initialized ast 0.1.0 for 0008:07:00.0 on minor 0
ast 0008:07:00.0: [drm] fb0: astdrmfb frame buffer device
With v6.15-rc, since the commit bcb81ac6ae ("iommu: Get DT/ACPI parsing
into the proper probe path"), the error returned with the warning is moved
to the SMMU device probe flow:
arm_smmu_probe_device+0x15c/0x4c0
__iommu_probe_device+0x150/0x4f8
probe_iommu_group+0x44/0x80
bus_for_each_dev+0x7c/0x100
bus_iommu_probe+0x48/0x1a8
iommu_device_register+0xb8/0x178
arm_smmu_device_probe+0x1350/0x1db0
which then fails the entire SMMU driver probe:
pci 0008:06:00.0: Adding to iommu group 21
pci 0008:07:00.0: stream 67328 already in tree
arm-smmu-v3 arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3 arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
Since SMMU driver had been already expecting a potential duplicated Stream
ID in arm_smmu_install_ste_for_dev(), change the arm_smmu_insert_master()
routine to ignore a duplicated ID from the fwspec->sids array as well.
Note: this has been failing the iommu_device_probe() since 2021, although a
recent iommu commit in v6.15-rc1 that moves iommu_device_probe() started to
fail the SMMU driver probe. Since nobody has cared about DMA Alias support,
leave that as it was but fix the fundamental iommu_device_probe() breakage.
Fixes: cdf315f907 ("iommu/arm-smmu-v3: Maintain a SID->device structure")
Cc: stable@vger.kernel.org
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/20250415185620.504299-1-nicolinc@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
UBSan caught a bug with IOMMU SVA domains, where the reported exponent
value in __arm_smmu_tlb_inv_range() was >= 64.
__arm_smmu_tlb_inv_range() uses the domain's pgsize_bitmap to compute
the number of pages to invalidate and the invalidation range. Currently
arm_smmu_sva_domain_alloc() does not setup the iommu domain's
pgsize_bitmap. This leads to __ffs() on the value returning 64 and that
leads to undefined behaviour w.r.t. shift operations
Fix this by initializing the iommu_domain's pgsize_bitmap to PAGE_SIZE.
Effectively the code needs to use the smallest page size for
invalidation
Cc: stable@vger.kernel.org
Fixes: eb6c97647b ("iommu/arm-smmu-v3: Avoid constructing invalid range commands")
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Balbir Singh <balbirs@nvidia.com>
Cc: Jean-Philippe Brucker <jean-philippe@linaro.org>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20250412002354.3071449-1-balbirs@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
pci1xxxx enables its PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_regions() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Moreover, since both functions are already managed in this driver, the
call to pci_release_regions() is unnecessary.
Remove the call to pci_release_regions().
Replace the call to sometimes-managed pci_request_regions() with one to
the always-managed pcim_request_all_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patch.msgid.link/20250417083902.23483-4-phasta@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
cavium-thunderx enables its PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_regions() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Moreover, since both functions are already managed in this driver, the
calls to pci_release_regions() are unnecessary.
Remove the calls to pci_release_regions().
Replace the call to sometimes-managed pci_request_regions() with one to
the always-managed pcim_request_all_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patch.msgid.link/20250417083902.23483-2-phasta@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 67e4fe3985 ("iommu/arm-smmu-v3: Use S2FWB for NESTED domains")
introduced S2FWB usage but omitted the corresponding feature detection.
As a result, vIOMMU allocation fails on FVP in arm_vsmmu_alloc(), due to
the following check:
if (!arm_smmu_master_canwbs(master) &&
!(smmu->features & ARM_SMMU_FEAT_S2FWB))
return ERR_PTR(-EOPNOTSUPP);
This patch adds the missing detection logic to prevent allocation
failure when S2FWB is supported.
Fixes: 67e4fe3985 ("iommu/arm-smmu-v3: Use S2FWB for NESTED domains")
Signed-off-by: Aneesh Kumar K.V (Arm) <aneesh.kumar@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Link: https://lore.kernel.org/r/20250408033351.1012411-1-aneesh.kumar@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Add missing DL_SRC_BE link,as well as Headphone L/R that are
provided by mt6359.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250417-mt8395-audio-sof-v1-5-30587426e5dd@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it also compatible for platform without external
codecs.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250417-mt8395-audio-sof-v1-4-30587426e5dd@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Other mt8195-mt6359 cards rely on external codecs,
add a card for board that only use the mt6359 codec.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250417-mt8395-audio-sof-v1-3-30587426e5dd@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'HPOL', 'HPOR', and 'Headset Mic' are rt5682 specific,
move these routes to mt8195_rt5682_init so we keep
'mt8195_rt5682_routes' for connection between mt8195 and
mt6359.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250417-mt8395-audio-sof-v1-1-30587426e5dd@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add check for the return value of spi_imx_setupxfer().
spi_imx->rx and spi_imx->tx function pointer can be NULL when
spi_imx_setupxfer() return error, and make NULL pointer dereference.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
0x0
spi_imx_pio_transfer+0x50/0xd8
spi_imx_transfer_one+0x18c/0x858
spi_transfer_one_message+0x43c/0x790
__spi_pump_transfer_message+0x238/0x5d4
__spi_sync+0x2b0/0x454
spi_write_then_read+0x11c/0x200
Signed-off-by: Tamura Dai <kirinode0@gmail.com>
Reviewed-by: Carlos Song <carlos.song@nxp.com>
Link: https://patch.msgid.link/20250417011700.14436-1-kirinode0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wmax_thermal_information() may also return -ENOMSG, which would leave
`id` uninitialized in thermal_profile_probe.
Reorder and modify logic to catch all errors.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/Z_-KVqNbD9ygvE2X@stanley.mountain
Fixes: 27e9e63398 ("platform/x86: alienware-wmi: Refactor thermal control methods")
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250416-smatch-fix-v1-1-35491b462d8f@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
In certain situations, the sysfs for uncore may not be present when all
CPUs in a package are offlined and then brought back online after boot.
This issue can occur if there is an error in adding the sysfs entry due
to a memory allocation failure. Retrying to bring the CPUs online will
not resolve the issue, as the uncore_cpu_mask is already set for the
package before the failure condition occurs.
This issue does not occur if the failure happens during module
initialization, as the module will fail to load in the event of any
error.
To address this, ensure that the uncore_cpu_mask is not set until the
successful return of uncore_freq_add_entry().
Fixes: dbce412a77 ("platform/x86/intel-uncore-freq: Split common and enumeration part")
Signed-off-by: Shouye Liu <shouyeliu@tencent.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250417032321.75580-1-shouyeliu@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
When an APU exits HW sleep with no active wake sources the Linux kernel will
rapidly assert that the APU can enter back into HW sleep. This happens in a
few ms. Contrasting this to Windows, Windows can take 10s of seconds to
enter back into the resiliency phase for Modern Standby.
For some situations this can be problematic because it can cause leakage
from VDDCR_SOC to VDD_MISC and force VDD_MISC outside of the electrical
design guide specifications. On some designs this will trip the over
voltage protection feature (OVP) of the voltage regulator module, but it
could cause APU damage as well.
To prevent this risk, add an explicit sleep call so that future attempts
to enter into HW sleep will have enough time to settle. This will occur
while the screen is dark and only on cases that the APU should enter HW
sleep again, so it shouldn't be noticeable to any user.
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20250414162446.3853194-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
- l2cap: Process valid commands in too long frame
- vhci: Avoid needless snprintf() calls
-----BEGIN PGP SIGNATURE-----
iQJMBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmgAGkwZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKZOmD/UbedvbIrN+fV9mUcTfWsOE
UDo+L3GOaowjHDmRu/YR2XD65HWxJGM93u3rksZXfW+wuLWrm6gUfDGphEHT8Xee
Oms+qWgBg/qqNX4gm0vmxGY9HeO9o+Ove8BN1cGudJAkZ5P4kz3vQ2Ytcb732tb5
zKgh+JaiUMa3eZnXmYKVpFiZ0V1c1iJwjsp2O+pXrBvM6uoheIZSnTKtFPFF199c
I09l30nYeKsZsRNgyCgYU3mOvNtEcHPrhH1Y8sXh5Oy88ffM/G/29FHWb3fd/wCd
Mo4G8Ciy70OY4xR1oeS/Mnt8mNIvja3AXlquRtKHvNgcY3e6DgKQZAWXLcMMRmOO
hdjy9pIUJLG09OGv92+HEMlnXMRvK9OYJ5GjbBVFxSHNk2b8FaIW7NdMm4xjVClZ
qcG5pl2a3Gji5sdsrtoP3jBO6ErHDwI0S5rrBYGiSqvAqBBRvveo9cl2GgPHviEF
IT0E6FzzyaR6xu9qpObw+LN13d4egEA2mi9TSHdUn/Vs1TCdk1zjKGOljKpcQWrc
It0B4cwDKJPiw5Be8AXhb+OgdYHmzjUsFz9FtXJ8X92nzJLC1ufWybvR2fPnQm47
NScQMRC3TjuWxcwuqZHYcaixO2efq4Kl58f2SF/SdBKlhlfpgOASML2PKp1AOweO
lSZNdBpVOgQIpFw2gkS7
=8ull
-----END PGP SIGNATURE-----
Merge tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- l2cap: Process valid commands in too long frame
- vhci: Avoid needless snprintf() calls
* tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: vhci: Avoid needless snprintf() calls
Bluetooth: l2cap: Process valid commands in too long frame
====================
Link: https://patch.msgid.link/20250416210126.2034212-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Peter Seiderer says:
====================
net: pktgen: fix checkpatch code style errors/warnings
Fix checkpatch detected code style errors/warnings detected in
the file net/core/pktgen.c (remaining checkpatch checks will be addressed
in a follow up patch set).
====================
Link: https://patch.msgid.link/20250415112916.113455-1-ps.report@gmx.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
