This adds some additional DT labels which are handy when referring
to the nodes in derived DTS(I) files. It will also make the
definitions more consistent, e.g. by adding gsbi2_serial and
gsbi5_serial where we previously "only" had gsbi4_serial defined.
While at it, add missing spaces after some DT labels and remove one
useless empty line.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Link: https://lore.kernel.org/r/20200902165159.7733-1-freifunk@adrianschmutzler.de
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 or 512 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 1x button (reset)
- 1x USB 2.0
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
This adds DTS for both the generic and custom Bit edition for Sartura.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200909195640.3127341-4-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Lets add labels to more commonly used nodes for easier modification in board DTS files.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200909195640.3127341-2-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200909163831.1894142-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable Qcom SMEM partition parser driver to make use of the NAND
partitions defined in Shared Memory (SMEM).
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118053853.56224-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable the Qcom SDX55 pinctrl driver and also enable the PINCTRL_MSM
driver explicitly since it is not selected by default directly.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118053853.56224-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Sockets and other non-regular files may actually expect short reads to
happen, don't retry reads for them. Because non-reg files don't set
FMODE_BUF_RASYNC and so it won't do second/retry do_read, we can filter
out those cases after first do_read() attempt with ret>0.
Cc: stable@vger.kernel.org # 5.9+
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IORING_OP_CLOSE is special in terms of cancelation, since it has an
intermediate state where we've removed the file descriptor but hasn't
closed the file yet. For that reason, it's currently marked with
IO_WQ_WORK_NO_CANCEL to prevent cancelation. This ensures that the op
is always run even if canceled, to prevent leaving us with a live file
but an fd that is gone. However, with SQPOLL, since a cancel request
doesn't carry any resources on behalf of the request being canceled, if
we cancel before any of the close op has been run, we can end up with
io-wq not having the ->files assigned. This can result in the following
oops reported by Joseph:
BUG: kernel NULL pointer dereference, address: 00000000000000d8
PGD 800000010b76f067 P4D 800000010b76f067 PUD 10b462067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 1788 Comm: io_uring-sq Not tainted 5.11.0-rc4 #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__lock_acquire+0x19d/0x18c0
Code: 00 00 8b 1d fd 56 dd 08 85 db 0f 85 43 05 00 00 48 c7 c6 98 7b 95 82 48 c7 c7 57 96 93 82 e8 9a bc f5 ff 0f 0b e9 2b 05 00 00 <48> 81 3f c0 ca 67 8a b8 00 00 00 00 41 0f 45 c0 89 04 24 e9 81 fe
RSP: 0018:ffffc90001933828 EFLAGS: 00010002
RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000000000d8
RBP: 0000000000000246 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff888106e8a140 R15: 00000000000000d8
FS: 0000000000000000(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000d8 CR3: 0000000106efa004 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
lock_acquire+0x31a/0x440
? close_fd_get_file+0x39/0x160
? __lock_acquire+0x647/0x18c0
_raw_spin_lock+0x2c/0x40
? close_fd_get_file+0x39/0x160
close_fd_get_file+0x39/0x160
io_issue_sqe+0x1334/0x14e0
? lock_acquire+0x31a/0x440
? __io_free_req+0xcf/0x2e0
? __io_free_req+0x175/0x2e0
? find_held_lock+0x28/0xb0
? io_wq_submit_work+0x7f/0x240
io_wq_submit_work+0x7f/0x240
io_wq_cancel_cb+0x161/0x580
? io_wqe_wake_worker+0x114/0x360
? io_uring_get_socket+0x40/0x40
io_async_find_and_cancel+0x3b/0x140
io_issue_sqe+0xbe1/0x14e0
? __lock_acquire+0x647/0x18c0
? __io_queue_sqe+0x10b/0x5f0
__io_queue_sqe+0x10b/0x5f0
? io_req_prep+0xdb/0x1150
? mark_held_locks+0x6d/0xb0
? mark_held_locks+0x6d/0xb0
? io_queue_sqe+0x235/0x4b0
io_queue_sqe+0x235/0x4b0
io_submit_sqes+0xd7e/0x12a0
? _raw_spin_unlock_irq+0x24/0x30
? io_sq_thread+0x3ae/0x940
io_sq_thread+0x207/0x940
? do_wait_intr_irq+0xc0/0xc0
? __ia32_sys_io_uring_enter+0x650/0x650
kthread+0x134/0x180
? kthread_create_worker_on_cpu+0x90/0x90
ret_from_fork+0x1f/0x30
Fix this by moving the IO_WQ_WORK_NO_CANCEL until _after_ we've modified
the fdtable. Canceling before this point is totally fine, and running
it in the io-wq context _after_ that point is also fine.
For 5.12, we'll handle this internally and get rid of the no-cancel
flag, as IORING_OP_CLOSE is the only user of it.
Cc: stable@vger.kernel.org
Fixes: b5dba59e0c ("io_uring: add support for IORING_OP_CLOSE")
Reported-by: "Abaci <abaci@linux.alibaba.com>"
Reviewed-and-tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Added documentation for devlink port and port function related commands.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Support changing the state of the SF port's function through devlink.
When activating the SF port's function, enable the hca in the device
followed by adding its auxiliary device.
When deactivating the SF port's function, delete its auxiliary device
followed by disabling the vHCA.
Port function attributes get/set callbacks are invoked with devlink
instance lock held. Such callbacks need to synchronize with sf port
table getting disabled either via sriov sysfs callback. Such callbacks
synchronize with table disable context holding table refcount.
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set pci/0000:06:00.0/32768 hw_addr 00:00:00:00:88:88 state active
$ devlink port show ens2f0npf0sf88 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
On port function activation, an auxiliary device is created in below
example.
$ devlink dev show
devlink dev show auxiliary/mlx5_core.sf.4
$ devlink port show auxiliary/mlx5_core.sf.4/1
auxiliary/mlx5_core.sf.4/1: type eth netdev p0sf88 flavour virtual port 0 splittable false
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To handle SF port management outside of the eswitch as independent
software layer, introduce eswitch notifier APIs so that mlx5 upper
layer who wish to support sf port management in switchdev mode can
perform its task whenever eswitch mode is set to switchdev or before
eswitch is disabled.
Initialize sf port table on such eswitch event.
Add SF port add and delete functionality in switchdev mode.
Destroy all SF ports when eswitch is disabled.
Expose SF port add and delete to user via devlink commands.
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
or by its unique port index:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00",
"state": "inactive",
"opstate": "detached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add helpers to enable/disable eswitch port, register its devlink port and
load its representor.
Signed-off-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prepare eswitch to handle SF vport during
(a) querying eswitch functions
(b) egress ACL creation
(c) account for SF vports in total vports calculation
Assign a dedicated placeholder for SFs vports and their representors.
They are placed after VFs vports and before ECPF vports as below:
[PF,VF0,...,VFn,SF0,...SFm,ECPF,UPLINK].
Change functions to map SF's vport numbers to indices when
accessing the vports or representors arrays, and vice versa.
Signed-off-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add auxiliary device driver for mlx5 subfunction auxiliary device.
A mlx5 subfunction is similar to PCI PF and VF. For a subfunction
an auxiliary device is created.
As a result, when mlx5 SF auxiliary device binds to the driver,
its netdev and rdma device are created, they appear as
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ ls -l /sys/class/net/eth1/device
/sys/class/net/eth1/device -> ../../../mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ devlink port show auxiliary/mlx5_core.sf.4/1
auxiliary/mlx5_core.sf.4/1: type eth netdev p0sf88 flavour virtual port 0 splittable false
$ rdma link show mlx5_0/1
link mlx5_0/1 state ACTIVE physical_state LINK_UP netdev p0sf88
$ rdma dev show
8: rocep6s0f1: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d113 sys_image_guid 248a:0703:00b3:d112
13: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
In future, devlink device instance name will adapt to have sfnum
annotation using either an alias or as devlink instance name described
in RFC [1].
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce API to add and delete an auxiliary device for an SF.
Each SF has its own dedicated window in the PCI BAR 2.
SF device is similar to PCI PF and VF that supports multiple class of
devices such as net, rdma and vdpa.
SF device will be added or removed in subsequent patch during SF
devlink port function state change command.
A subfunction device exposes user supplied subfunction number which will
be further used by systemd/udev to have deterministic name for its
netdevice and rdma device.
An mlx5 subfunction auxiliary device example:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88 state active
On activation,
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
vhca state events indicates change in the state of the vhca that may
occur due to a SF allocation, deallocation or enabling/disabling the
SF HCA.
Introduce vhca state event handler which will be used by SF devlink
port manager and SF hardware id allocator in subsequent patches
to act on the event.
This enables single entity to subscribe, query and rearm the event
for a function.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
devlink port function can be in active or inactive state.
Allow users to get and set port function's state.
When the port function it activated, its operational state may change
after a while when the device is created and driver binds to it.
Similarly on deactivation flow.
To clearly describe the state of the port function and its device's
operational state in the host system, define state and opstate
attributes.
Example of a PCI SF port which supports a port function:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set pci/0000:06:00.0/32768 hw_addr 00:00:00:00:88:88 state active
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Extended devlink interface for the user to add and delete a port.
Extend devlink to connect user requests to driver to add/delete
a port in the device.
Driver routines are invoked without holding devlink instance lock.
This enables driver to perform several devlink objects registration,
unregistration such as (port, health reporter, resource etc) by using
existing devlink APIs.
This also helps to uniformly use the code for port unregistration
during driver unload and during port deletion initiated by user.
Examples of add, show and delete commands:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ udevadm test-builtin net_id /sys/class/net/eth6
Load module index
Parsed configuration file /usr/lib/systemd/network/99-default.link
Created link configuration context.
Using default interface naming scheme 'v245'.
ID_NET_NAMING_SCHEME=v245
ID_NET_NAME_PATH=enp6s0f0npf0sf88
ID_NET_NAME_SLOT=ens2f0npf0sf88
Unload module index
Unloaded link configuration context.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A PCI sub-function (SF) represents a portion of the device similar
to PCI VF.
In an eswitch, PCI SF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with SF,
and its representor netdevice, introduce a PCI SF port flavour.
When devlink port flavour is PCI SF, fill up PCI SF attributes of the
port.
Extend port name creation using PCI PF and SF number scheme on best
effort basis, so that vendor drivers can skip defining their own
scheme.
This is done as cApfNSfM, where A, N and M are controller, PCI PF and
PCI SF number respectively.
This is similar to existing naming for PCI PF and PCI VF ports.
An example view of a PCI SF port:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state active opstate attached
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prepare code to fill zero or more port function optional attributes.
Subsequent patch makes use of this to fill more port function
attributes.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add support for pshold block to drive pshold towards the PMIC, which is
used to trigger a configurable event such as reboot or poweroff of the
SDX55 platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118051005.55958-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/sw/rdmavt/qp.c:165: warning: Function parameter or member 'rdi' not described in 'rvt_wss_init'
drivers/infiniband/sw/rdmavt/qp.c:329: warning: Function parameter or member 'rdi' not described in 'init_qpn_table'
drivers/infiniband/sw/rdmavt/qp.c:534: warning: Function parameter or member 'type' not described in 'alloc_qpn'
drivers/infiniband/sw/rdmavt/qp.c:664: warning: Function parameter or member 'wqe' not described in 'rvt_swqe_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:664: warning: Function parameter or member 'lkey' not described in 'rvt_swqe_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:682: warning: Function parameter or member 'qp' not described in 'rvt_qp_sends_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:682: warning: Function parameter or member 'lkey' not described in 'rvt_qp_sends_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:706: warning: Function parameter or member 'qp' not described in 'rvt_qp_acks_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:706: warning: Function parameter or member 'lkey' not described in 'rvt_qp_acks_has_lkey'
drivers/infiniband/sw/rdmavt/qp.c:866: warning: Function parameter or member 'rdi' not described in 'rvt_init_qp'
drivers/infiniband/sw/rdmavt/qp.c:920: warning: Function parameter or member 'rdi' not described in '_rvt_reset_qp'
drivers/infiniband/sw/rdmavt/qp.c:1736: warning: Function parameter or member 'udata' not described in 'rvt_destroy_qp'
drivers/infiniband/sw/rdmavt/qp.c:1924: warning: Function parameter or member 'qp' not described in 'rvt_qp_valid_operation'
drivers/infiniband/sw/rdmavt/qp.c:1924: warning: Function parameter or member 'post_parms' not described in 'rvt_qp_valid_operation'
drivers/infiniband/sw/rdmavt/qp.c:1924: warning: Function parameter or member 'wr' not described in 'rvt_qp_valid_operation'
drivers/infiniband/sw/rdmavt/qp.c:2020: warning: Function parameter or member 'call_send' not described in 'rvt_post_one_wr'
drivers/infiniband/sw/rdmavt/qp.c:2621: warning: Function parameter or member 'qp' not described in 'rvt_stop_rnr_timer'
Link: https://lore.kernel.org/r/20210121094519.2044049-31-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_iba6120.c:1229: warning: Function parameter or member 'ppd' not described in 'qib_6120_bringup_serdes'
drivers/infiniband/hw/qib/qib_iba6120.c:1229: warning: Excess function parameter 'dd' description in 'qib_6120_bringup_serdes'
drivers/infiniband/hw/qib/qib_iba6120.c:1436: warning: Function parameter or member 'ppd' not described in 'qib_6120_setup_setextled'
drivers/infiniband/hw/qib/qib_iba6120.c:1436: warning: Excess function parameter 'dd' description in 'qib_6120_setup_setextled'
drivers/infiniband/hw/qib/qib_iba6120.c:1836: warning: Function parameter or member 'type' not described in 'qib_6120_put_tid'
drivers/infiniband/hw/qib/qib_iba6120.c:1836: warning: Excess function parameter 'tidtype' description in 'qib_6120_put_tid'
drivers/infiniband/hw/qib/qib_iba6120.c:1903: warning: Function parameter or member 'type' not described in 'qib_6120_put_tid_2'
drivers/infiniband/hw/qib/qib_iba6120.c:1903: warning: Excess function parameter 'tidtype' description in 'qib_6120_put_tid_2'
drivers/infiniband/hw/qib/qib_iba6120.c:1944: warning: Function parameter or member 'rcd' not described in 'qib_6120_clear_tids'
drivers/infiniband/hw/qib/qib_iba6120.c:1944: warning: Excess function parameter 'ctxt' description in 'qib_6120_clear_tids'
drivers/infiniband/hw/qib/qib_iba6120.c:2018: warning: Function parameter or member 'kinfo' not described in 'qib_6120_get_base_info'
drivers/infiniband/hw/qib/qib_iba6120.c:2018: warning: Excess function parameter 'kbase' description in 'qib_6120_get_base_info'
drivers/infiniband/hw/qib/qib_iba6120.c:2277: warning: Function parameter or member 'ppd' not described in 'qib_portcntr_6120'
drivers/infiniband/hw/qib/qib_iba6120.c:2277: warning: Function parameter or member 'reg' not described in 'qib_portcntr_6120'
drivers/infiniband/hw/qib/qib_iba6120.c:2277: warning: Excess function parameter 'dd' description in 'qib_portcntr_6120'
drivers/infiniband/hw/qib/qib_iba6120.c:2277: warning: Excess function parameter 'creg' description in 'qib_portcntr_6120'
drivers/infiniband/hw/qib/qib_iba6120.c:2620: warning: Function parameter or member 't' not described in 'qib_get_6120_faststats'
Link: https://lore.kernel.org/r/20210121094519.2044049-30-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_verbs.c:1077: warning: Function parameter or member 'ppd' not described in 'qib_get_counters'
drivers/infiniband/hw/qib/qib_verbs.c:1077: warning: Excess function parameter 'dd' description in 'qib_get_counters'
drivers/infiniband/hw/qib/qib_verbs.c:1686: warning: Function parameter or member 'qp' not described in '_qib_schedule_send'
drivers/infiniband/hw/qib/qib_verbs.c:1703: warning: Function parameter or member 'qp' not described in 'qib_schedule_send'
Link: https://lore.kernel.org/r/20210121094519.2044049-29-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_iba7322.c:2521: warning: Function parameter or member 'ppd' not described in 'qib_7322_mini_quiet_serdes'
drivers/infiniband/hw/qib/qib_iba7322.c:2521: warning: Excess function parameter 'dd' description in 'qib_7322_mini_quiet_serdes'
drivers/infiniband/hw/qib/qib_iba7322.c:3768: warning: Function parameter or member 'type' not described in 'qib_7322_put_tid'
drivers/infiniband/hw/qib/qib_iba7322.c:3768: warning: Excess function parameter 'tidtype' description in 'qib_7322_put_tid'
drivers/infiniband/hw/qib/qib_iba7322.c:3806: warning: Function parameter or member 'rcd' not described in 'qib_7322_clear_tids'
drivers/infiniband/hw/qib/qib_iba7322.c:3806: warning: Excess function parameter 'ctxt' description in 'qib_7322_clear_tids'
drivers/infiniband/hw/qib/qib_iba7322.c:3872: warning: Function parameter or member 'kinfo' not described in 'qib_7322_get_base_info'
drivers/infiniband/hw/qib/qib_iba7322.c:3872: warning: Excess function parameter 'kbase' description in 'qib_7322_get_base_info'
drivers/infiniband/hw/qib/qib_iba7322.c:4730: warning: Function parameter or member 'reg' not described in 'qib_portcntr_7322'
drivers/infiniband/hw/qib/qib_iba7322.c:4730: warning: Excess function parameter 'creg' description in 'qib_portcntr_7322'
drivers/infiniband/hw/qib/qib_iba7322.c:5109: warning: Function parameter or member 't' not described in 'qib_get_7322_faststats'
drivers/infiniband/hw/qib/qib_iba7322.c:7189: warning: Function parameter or member 'pdev' not described in 'qib_init_iba7322_funcs'
drivers/infiniband/hw/qib/qib_iba7322.c:7189: warning: Excess function parameter 'dev' description in 'qib_init_iba7322_funcs'
Link: https://lore.kernel.org/r/20210121094519.2044049-28-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/sw/rdmavt/mr.c:380: warning: Function parameter or member 'virt_addr' not described in 'rvt_reg_user_mr'
drivers/infiniband/sw/rdmavt/mr.c:449: warning: Function parameter or member 'qp' not described in 'rvt_dereg_clean_qp_cb'
drivers/infiniband/sw/rdmavt/mr.c:449: warning: Function parameter or member 'v' not described in 'rvt_dereg_clean_qp_cb'
drivers/infiniband/sw/rdmavt/mr.c:466: warning: Function parameter or member 'mr' not described in 'rvt_dereg_clean_qps'
drivers/infiniband/sw/rdmavt/mr.c:484: warning: Function parameter or member 'mr' not described in 'rvt_check_refs'
drivers/infiniband/sw/rdmavt/mr.c:484: warning: Function parameter or member 't' not described in 'rvt_check_refs'
drivers/infiniband/sw/rdmavt/mr.c:513: warning: Function parameter or member 'mr' not described in 'rvt_mr_has_lkey'
drivers/infiniband/sw/rdmavt/mr.c:513: warning: Function parameter or member 'lkey' not described in 'rvt_mr_has_lkey'
drivers/infiniband/sw/rdmavt/mr.c:526: warning: Function parameter or member 'ss' not described in 'rvt_ss_has_lkey'
drivers/infiniband/sw/rdmavt/mr.c:526: warning: Function parameter or member 'lkey' not described in 'rvt_ss_has_lkey'
drivers/infiniband/sw/rdmavt/mr.c:551: warning: Function parameter or member 'udata' not described in 'rvt_dereg_mr'
Link: https://lore.kernel.org/r/20210121094519.2044049-27-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/hfi1/file_ops.c:1533: warning: Function parameter or member 'arg' not described in 'manage_rcvq'
drivers/infiniband/hw/hfi1/file_ops.c:1533: warning: Excess function parameter 'start_stop' description in 'manage_rcvq'
Link: https://lore.kernel.org/r/20210121094519.2044049-26-lee.jones@linaro.org
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_iba7220.c:1726: warning: Function parameter or member 'ppd' not described in 'qib_setup_7220_setextled'
drivers/infiniband/hw/qib/qib_iba7220.c:1726: warning: Excess function parameter 'dd' description in 'qib_setup_7220_setextled'
drivers/infiniband/hw/qib/qib_iba7220.c:2154: warning: Function parameter or member 'type' not described in 'qib_7220_put_tid'
drivers/infiniband/hw/qib/qib_iba7220.c:2154: warning: Excess function parameter 'tidtype' description in 'qib_7220_put_tid'
drivers/infiniband/hw/qib/qib_iba7220.c:2192: warning: Function parameter or member 'rcd' not described in 'qib_7220_clear_tids'
drivers/infiniband/hw/qib/qib_iba7220.c:2192: warning: Excess function parameter 'ctxt' description in 'qib_7220_clear_tids'
drivers/infiniband/hw/qib/qib_iba7220.c:2248: warning: Function parameter or member 'kinfo' not described in 'qib_7220_get_base_info'
drivers/infiniband/hw/qib/qib_iba7220.c:2248: warning: Excess function parameter 'kbase' description in 'qib_7220_get_base_info'
drivers/infiniband/hw/qib/qib_iba7220.c:2903: warning: Function parameter or member 'ppd' not described in 'qib_portcntr_7220'
drivers/infiniband/hw/qib/qib_iba7220.c:2903: warning: Function parameter or member 'reg' not described in 'qib_portcntr_7220'
drivers/infiniband/hw/qib/qib_iba7220.c:2903: warning: Excess function parameter 'dd' description in 'qib_portcntr_7220'
drivers/infiniband/hw/qib/qib_iba7220.c:2903: warning: Excess function parameter 'creg' description in 'qib_portcntr_7220'
drivers/infiniband/hw/qib/qib_iba7220.c:3242: warning: Function parameter or member 't' not described in 'qib_get_7220_faststats'
drivers/infiniband/hw/qib/qib_iba7220.c:4479: warning: Function parameter or member 'pdev' not described in 'qib_init_iba7220_funcs'
drivers/infiniband/hw/qib/qib_iba7220.c:4479: warning: Excess function parameter 'dev' description in 'qib_init_iba7220_funcs'
Link: https://lore.kernel.org/r/20210121094519.2044049-25-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/hfi1/exp_rcv.c:56: warning: Function parameter or member 'set' not described in 'hfi1_exp_tid_set_init'
drivers/infiniband/hw/hfi1/exp_rcv.c:66: warning: Function parameter or member 'rcd' not described in 'hfi1_exp_tid_group_init'
drivers/infiniband/hw/hfi1/exp_rcv.c:77: warning: Function parameter or member 'rcd' not described in 'hfi1_alloc_ctxt_rcv_groups'
drivers/infiniband/hw/hfi1/exp_rcv.c:114: warning: Function parameter or member 'rcd' not described in 'hfi1_free_ctxt_rcv_groups'
Link: https://lore.kernel.org/r/20210121094519.2044049-24-lee.jones@linaro.org
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/sw/rdmavt/mcast.c:195: warning: Function parameter or member 'rdi' not described in 'rvt_mcast_add'
drivers/infiniband/sw/rdmavt/mcast.c:195: warning: Function parameter or member 'ibp' not described in 'rvt_mcast_add'
Link: https://lore.kernel.org/r/20210121094519.2044049-23-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_user_pages.c:60: warning: Function parameter or member 'hwdev' not described in 'qib_map_page'
drivers/infiniband/hw/qib/qib_user_pages.c:60: warning: Function parameter or member 'page' not described in 'qib_map_page'
drivers/infiniband/hw/qib/qib_user_pages.c:60: warning: Function parameter or member 'daddr' not described in 'qib_map_page'
Link: https://lore.kernel.org/r/20210121094519.2044049-22-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Function parameter or member 'in' not described in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Function parameter or member 'in_mad_size' not described in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Function parameter or member 'out' not described in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Function parameter or member 'out_mad_size' not described in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Function parameter or member 'out_mad_pkey_index' not described in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Excess function parameter 'in_mad' description in 'rvt_process_mad'
drivers/infiniband/sw/rdmavt/mad.c:75: warning: Excess function parameter 'out_mad' description in 'rvt_process_mad'
Link: https://lore.kernel.org/r/20210121094519.2044049-21-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_ud.c:231: warning: Function parameter or member 'flags' not described in 'qib_make_ud_req'
Link: https://lore.kernel.org/r/20210121094519.2044049-20-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_uc.c:49: warning: Function parameter or member 'flags' not described in 'qib_make_uc_req'
Link: https://lore.kernel.org/r/20210121094519.2044049-19-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_tx.c:383: warning: Function parameter or member 'rcd' not described in 'qib_chg_pioavailkernel'
Link: https://lore.kernel.org/r/20210121094519.2044049-18-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/qib/qib_twsi.c:175: warning: Function parameter or member 'last' not described in 'rd_byte'
Link: https://lore.kernel.org/r/20210121094519.2044049-17-lee.jones@linaro.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/infiniband/hw/hfi1/chip.c:1335: warning: Function parameter or member 'dd' not described in 'hfi1_addr_from_offset'
drivers/infiniband/hw/hfi1/chip.c:1335: warning: Function parameter or member 'offset' not described in 'hfi1_addr_from_offset'
drivers/infiniband/hw/hfi1/chip.c:1350: warning: Function parameter or member 'dd' not described in 'read_csr'
drivers/infiniband/hw/hfi1/chip.c:1350: warning: Function parameter or member 'offset' not described in 'read_csr'
drivers/infiniband/hw/hfi1/chip.c:1363: warning: Function parameter or member 'dd' not described in 'write_csr'
drivers/infiniband/hw/hfi1/chip.c:1363: warning: Function parameter or member 'offset' not described in 'write_csr'
drivers/infiniband/hw/hfi1/chip.c:1363: warning: Function parameter or member 'value' not described in 'write_csr'
drivers/infiniband/hw/hfi1/chip.c:1385: warning: Function parameter or member 'dd' not described in 'get_csr_addr'
drivers/infiniband/hw/hfi1/chip.c:1385: warning: Function parameter or member 'offset' not described in 'get_csr_addr'
drivers/infiniband/hw/hfi1/chip.c:8442: warning: Function parameter or member 'rcd' not described in 'receive_interrupt_common'
drivers/infiniband/hw/hfi1/chip.c:8491: warning: Function parameter or member 'napi' not described in 'hfi1_netdev_rx_napi'
drivers/infiniband/hw/hfi1/chip.c:8491: warning: Function parameter or member 'budget' not described in 'hfi1_netdev_rx_napi'
drivers/infiniband/hw/hfi1/chip.c:14221: warning: Function parameter or member 'dd' not described in 'init_qpmap_table'
drivers/infiniband/hw/hfi1/chip.c:14221: warning: Function parameter or member 'first_ctxt' not described in 'init_qpmap_table'
drivers/infiniband/hw/hfi1/chip.c:14221: warning: Function parameter or member 'last_ctxt' not described in 'init_qpmap_table'
drivers/infiniband/hw/hfi1/chip.c:14399: warning: Function parameter or member 'dd' not described in 'init_qos'
drivers/infiniband/hw/hfi1/chip.c:14399: warning: Function parameter or member 'rmt' not described in 'init_qos'
drivers/infiniband/hw/hfi1/chip.c:15032: warning: Function parameter or member 'dd' not described in 'hfi1_init_dd'
drivers/infiniband/hw/hfi1/chip.c:15032: warning: Excess function parameter 'dev' description in 'hfi1_init_dd'
drivers/infiniband/hw/hfi1/chip.c:15032: warning: Excess function parameter 'ent' description in 'hfi1_init_dd'
drivers/infiniband/hw/hfi1/chip.c:15395: warning: Function parameter or member 'ppd' not described in 'create_pbc'
drivers/infiniband/hw/hfi1/chip.c:15395: warning: Function parameter or member 'srate_mbs' not described in 'create_pbc'
drivers/infiniband/hw/hfi1/chip.c:15395: warning: Function parameter or member 'dw_len' not described in 'create_pbc'
drivers/infiniband/hw/hfi1/chip.c:15395: warning: Excess function parameter 'srate' description in 'create_pbc'
drivers/infiniband/hw/hfi1/chip.c:15395: warning: Excess function parameter 'dwlen' description in 'create_pbc'
Link: https://lore.kernel.org/r/20210121094519.2044049-16-lee.jones@linaro.org
Cc: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>