'wq_sysfs_register()' in annotation for 'WQ_SYSFS' is unavailable,
change it to 'workqueue_sysfs_register()'.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Support for the SDM630/660 series of SoCs was added to the driver:
document the qcom,sdm660-qusb2-phy compatible here.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114174718.398638-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SDM660 SoC uses the same configuration as MSM8996, but the
clock scheme uses a differential reference clock and none of
the SoCs in this series (630, 636 and others) have got a usable
PHY_CLK_SCHEME register in the TCSR for clk scheme detection.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114174718.398638-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TCSR's PHY_CLK_SCHEME register is not available on all SoC
models, but some may still use a differential reference clock.
In preparation for these SoCs, add a se_clk_scheme_default
configuration entry and declare it to true for all currently
supported SoCs (retaining the previous defaults.
This patch brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114174718.398638-1-angelogioacchino.delregno@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the compatible strings for the USB2 PHYs found on QCOM
SM8250 & SM8350 SoCs.
Note that the SM8250 compatible is already in use in the dts and
driver implementation but was missing from the documentation.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210115174723.7424-4-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB DP & UNI PHYs found on SM8350. These use
version 5.0.0 of the QMP PHY IP and thus require new "V5"
definitions of the register offset macros for the QSERDES RX
and TX blocks. The QSERDES common and QPHY PCS blocks' register
offsets are largely unchanged from V4 so some of the existing
macros can be reused.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210115174723.7424-3-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the compatible strings for the USB3 PHYs found on SM8150, SM8250
and SM8350 SoCs. These require separate subschemas due to the different
required clock entries.
Note the SM8150 and SM8250 compatibles have already been in place in
the dts as well as the driver implementation but were missing from
the documentation.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210115174723.7424-2-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are too many logs on startup, e.g.
[ 8811.851497] cdns_fill_msg_resp: 2 callbacks suppressed
[ 8811.851497] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851498] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851499] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851499] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851500] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851500] intel-sdw intel-sdw.0: Msg Ack not received
[ 8811.851502] intel-sdw intel-sdw.0: Msg ignored for Slave 0
[ 8811.851503] soundwire sdw-master-0: No more devices to enumerate
We can skip the 'Msg Ack not received' since it's typical of the
enumeration end, and conversely add the information on which command
fails.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code reports a NAK only when ACK=0
This is not aligned with the SoundWire 1.x specifications.
Table 32 in the SoundWire 1.2 specification shows that a Device shall
not set NAK=1 if ACK=1. But Table 33 shows the Combined Response
may very well be NAK=1/ACK=1, e.g. if another Device than the one
addressed reports a parity error.
NAK=1 signals a 'Command_Aborted', regardless of the ACK bit value.
Move the tests for NAK so that the NAK=1/ACK=1 combination is properly
detected according to the specification.
Fixes: 956baa1992 ('soundwire: cdns: Add sdw_master_ops and IO transfer support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current error log does not provide details on the type of
transfers and which address/count was requested. All this information
can help locate in which parts of the configuration process an error
occurred.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing debug log only mentions a state change, without providing
any details. For integration and stress-tests, it's helpful to see in
the dmesg log the reason for the state change.
The value is intended for power users and isn't converted as
human-readable values. But for the record each device has a 4-bit
status:
BIT(0): Unattached
BIT(1): Attached
BIT(2): Alert
BIT(3): Reserved (should not happen)
Example:
[ 121.891288] intel-sdw intel-sdw.0: Slave status change: 0x2
<< this shows a Device0 Attached
[ 121.891295] soundwire sdw-master-0: Slave attached, programming device number
[ 121.891629] soundwire sdw-master-0: SDW Slave Addr: 30025d071101
[ 121.891632] soundwire sdw-master-0: SDW Slave class_id 1, part_id 711, mfg_id 25d, unique_id 0, version 3
[ 121.892011] intel-sdw intel-sdw.0: Msg ignored for Slave 0
[ 121.892013] soundwire sdw-master-0: No more devices to enumerate
[ 121.892200] intel-sdw intel-sdw.0: Slave status change: 0x21
<< this shows the device now Attached as Device1 and Unattached as
Device0, i.e. a successful enumeration.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We mix decimal and hexadecimal values, this leads to confusions in
dmesg logs and bug reports. Let's add a 0x prefix for all hexadecimal
values and a format when more than 4 bits are used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Leon Romanovsky says:
====================
Be more strict with DEVX get/set operations for the obj_id.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'devx_set_get':
RDMA/mlx5: Use strict get/set operations for obj_id
RDMA/mlx5: Use the correct obj_id upon DEVX TIR creation
net/mlx5: Expose ifc bits for query modify header
dev->power.runtime_error will be set to the return value of the runtime
suspend callback function, and runtime resume function will return
-EINVAL if dev->power.runtime_error is not 0.
Somehow the codec rarely doesn't return an ACK to the clock prepare
command. If we stop the runtime suspend process and return error, we
will not be able to resume again. Likewise, if the codec lost sync and
did not rejoin, the resume operation will also fail. As a result, the
SoundWire bus can not be used anymore.
This patch suggests to finish the runtime suspend process even if we fail
to stop sdw bus clock. In the case where we do a hardware reset, the codecs
will be reconfigured completely. In the case where we use the regular clock
stop, the codecs keep their state and worst case will fall off the bus and
reattach.
The only drawback is that the power consumption may be higher and
device-initiated interrupts may be lost, but at least audio function can
still work after resume.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210114030248.9005-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
link_id can be zero and if we have multiple controller instances
in a system like Qualcomm debugfs will end-up with duplicate namespace
resulting in incorrect debugfs entries.
Using id should give a unique debugfs directory entry and should fix below
warning too.
"debugfs: Directory 'master-0' with parent 'soundwire' already present!"
Fixes: bf03473d5b ("soundwire: add debugfs support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210115162559.20869-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only place sdw_slave_dev_attr_group is used is when its address is
passed to devm_device_add_group() which takes a pointer to const struct
attribute_group. Make it const to allow the compiler to put it in
read-only memory. This makes all attribute_group structs in the file
const. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210117221622.34315-1-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently the timeout for SoundWire individual transactions is 2s.
This is too large in comparison with the enumeration and completion
timeouts used in codec drivers.
A command will typically be handled in less than 100us, so 500ms for
the command completion is more than generous.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115061651.9740-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use strict get/set operations for obj_id based on the specific object
type. This comes to prevent any miss match between the general header to
the legacy header commands.
Link: https://lore.kernel.org/r/20201230130121.180350-4-leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use the correct obj_id upon DEVX TIR creation by strictly taking the tirn
24 bits and not the general obj_id which is 32 bits.
Fixes: 7efce3691d ("IB/mlx5: Add obj create and destroy functionality")
Link: https://lore.kernel.org/r/20201230130121.180350-2-leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
For performance, BO page mappings can stay in place even if the
map counter has returned to 0. In these cases, the existing page
mapping has to be reused by the next vmap operation. Otherwise
a new mapping would be installed and the old mapping's pages leak.
Fix the issue by reusing existing page mappings for vmap operations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 1086db71a1 ("drm/vram-helper: Remove invariant parameters from internal kmap function")
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Eli Cohen <elic@nvidia.com>
Reported-by: Eli Cohen <elic@nvidia.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Christian König <christian.koenig@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210118144639.27307-1-tzimmermann@suse.de
ASoC: cpcap: Implement set_tdm_slot for voice call support
For using cpcap for voice calls, we need to route audio directly from
the modem to cpcap for TDM (Time Division Multiplexing). The voice call
is direct data between the modem and cpcap with no CPU involvment. In
this mode, the cpcap related audio mixer controls work for the speaker
selection and volume though.
To do this, we need to implement standard snd_soc_dai_set_tdm_slot()
for cpcap. Then the modem codec driver can use snd_soc_dai_set_sysclk(),
snd_soc_dai_set_fmt(), and snd_soc_dai_set_tdm_slot() to configure a
voice call.
Let's add cpcap_voice_set_tdm_slot() for this, and cpcap_voice_call()
helper to configure the additional registers needed for voice call.
Let's also clear CPCAP_REG_VAUDIOC on init in case we have the bit for
CPCAP_BIT_VAUDIO_MODE0 set on init.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20210112174704.GA13496@duo.ucw.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not guaranteed that I2S RX is disabled when the kernel booting.
For example, if the kernel crashes while it is enabled, it will keep
enabled until the next time EC reboots. Reset I2S RX when probing to
fix this issue.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210115075301.47995-2-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the new command EC_CODEC_I2S_RX_RESET in ec_codec_i2s_rx_subcmd,
which is used for resetting the EC codec.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210115075301.47995-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Tegra audio machine driver which is based on generic audio graph card
driver. It re-uses most of the common stuff from audio graph driver and
uses the same DT binding. Required Tegra specific customizations are done
in the driver and additional DT bindings are required for clock handling.
Details on the customizations done:
- Update PLL rates at runtime: Tegra HW supports multiple sample rates
(multiples of 8x and 11.025x) and both of these groups require different
PLL rates. Hence there is a requirement to update this at runtime.
This is achieved by providing a custom 'snd_soc_ops' and in hw_param()
callback PLL rate is updated as per the sample rate.
- Internal structure 'tegra_audio_graph_data' is used to maintain clock
handles of PLL.
- The 'force_dpcm' flag is set to use DPCM for all DAI links.
- The 'component_chaining' flag is set to use DPCM with component model.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1611048496-24650-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add YAML schema for Tegra audio graph sound card DT bindings. It uses the
same DT bindings provided by generic audio graph driver. Along with this
few standard clock DT bindings are added which are specifically required
for Tegra audio.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1611048496-24650-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree binding properties of generic graph to ASoC component
devices. This allows to define audio ports out of these components or
DAIs and audio graph based sound card can be realised with this.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1611048496-24650-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC tegra PCM code still has explicit calls of dma_set_mask() and
dma_set_coherent_mask().
Let's simplify with dma_set_mask_and_coherent().
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210114133337.1039-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Intel SOF driver still has explicit calls of dma_set_mask() and
dma_set_coherent_mask().
Let's simplify with dma_set_mask_and_coherent().
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210114133337.1039-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Intel Skylake driver still has explicit calls of dma_set_mask()
and dma_set_coherent_mask().
Let's simplify with dma_set_mask_and_coherent().
Cc: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210114133337.1039-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than trying to avoid the use-after-free possible with the current
context chasing, simply remove presentation of the per-client stats from
debugfs. While we know from bug reports that this debugfs/i915_gem_objects
has been used by chromeos (and chrome itself) for debug purposes, google
suggests that it is unparsed, so we are free to invoke debugfs is not
ABI and remove details from it.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118110854.1873-1-chris@chris-wilson.co.uk
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip") moved the
Tegra GPIO driver to the generic GPIO IRQ chip infrastructure and made
the IRQ domain hierarchical, so the driver needs to pull in the support
infrastructure via the GPIOLIB_IRQCHIP and IRQ_DOMAIN_HIERARCHY Kconfig
options.
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
As the comment in usb_disconnect() hints, do not defer the
disconnect processing, and instead just do it directly in
the irq handler. This allows the driver to avoid using a
nowadays deprecated tasklet.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210119001653.127975-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update old comments as of 8b4c62aef6 (usb: gadget: u_serial: process RX
in workqueue instead of tasklet).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210119001321.127750-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preventing the driver from being built-in when USB Role
Switch Class is being build as module. That fixes a
potential undefined reference error.
Fixes: 89795852c9 ("usb: typec: ucsi: Add support for USB role switch")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210119083405.18325-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115211532.19837-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
All the defconfig files have replaced PCIE_RCAR config option with
PCIE_RCAR_HOST config option which built the same driver, so we can
now safely drop PCIE_RCAR config option.
Link: https://lore.kernel.org/r/20201229170848.18482-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
BCM4908 uses external MISC block for controlling PERST# signal. Use it
as a reset controller.
Link: https://lore.kernel.org/r/20201210180421.7230-3-zajec5@gmail.com
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 is a SoC family with PCIe controller sharing design with the one
for STB. BCM4908 has different power management and memory controller so
few tweaks are required.
PERST# signal on BCM4908 is handled by an external MISC block so it
needs specifying a reset phandle.
Link: https://lore.kernel.org/r/20201210180421.7230-2-zajec5@gmail.com
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The benefit of only resetting a single engine is that we leave other
streams of userspace work intact across a hang; vital for process
isolation. We had wired up individual engine resets for gen6, but only
enabled it from gen8; now let's turn it on for the forgotten gen7. gen6
is still a mystery as how to unravel some global state that appears to
be reset along with an engine (in particular the ppgtt enabling in
GFX_MODE).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119110802.22228-6-chris@chris-wilson.co.uk
Take advantage of calling xcs_resume under a forcewake by using direct
mmio access. In particular, we can avoid the sleeping variants to allow
resume to be called from softirq context, required for engine resets.
v2: Keep the posting read at the start of resume as a guardian memory
barrier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119110802.22228-5-chris@chris-wilson.co.uk
During the reset of ring submission, we first stop the engine by
clearing the HEAD/TAIL and marking the ring as disabled. However, it
would be safer to disable the ring (after emptying) before resetting the
HEAD/TAIL.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119110802.22228-4-chris@chris-wilson.co.uk
CI reports that Baytail requires one more invalidate after CACHE_MODE
for it to be happy.
Fixes: ace44e13e5 ("drm/i915/gt: Clear CACHE_MODE prior to clearing residuals")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119110802.22228-1-chris@chris-wilson.co.uk
While immensely convenient for developing to only tackle the first
error, and not be flooded by repeated or secondiary issues, many more
casual testers are not setup to remotely capture debug traces. For those
testers, it is more beneficial to keep the system running in the remote
chance that they are able to extract the original debug logs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114113434.8229-2-chris@chris-wilson.co.uk