The driver will compile with warning without OF because armada38x_data and
armada8k_data will be defined but not used. It would be possible to move
then in the #ifdef CONFIG_OF section but then their members will be defined
but not used. Instead of moving most of the driver in the #ifdef, simply
depend on OF.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210202112219.3610853-3-alexandre.belloni@bootlin.com
Disabling all event calls is already handled by the core right before
starting the DAA process. Do not do it again when the DAA process
completes, it is redundant.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201228105501.6104-1-miquel.raynal@bootlin.com
Add support for Silvaco I3C dual-role IP. The master role is supported
in SDR mode only. I2C transfers have not been tested but are shared
because they are very close to the I3C transfers in terms of register
configuration.
The IBI processing follows this logic:
- When a slave advertizes an interrupt (SDA pulled low) an interrupt
gets generated by the master. This time is unbounded and may be
deferred.
- The IRQ handler itself does not process anything: it only queues a
work that will be run in non-atomic context. This is needed because
short wait periods must be experienced.
- The IBI job is divided in two parts: the first one is "critical" in
the sense that it may not support getting interrupted. If this
happens, after this first section the driver checks the master error
register and depending on its content either flushes everything and
errors out, or ends the processing (this second section may be
interrupted).
- If the critical section got interrupted, the slave will
automatically respin it's IBI request when it will be allowed to.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-6-miquel.raynal@bootlin.com
Silvaco provide a dual-role I3C master.
Description is rather simple: it needs a register mapping, three
clocks and an interrupt.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-5-miquel.raynal@bootlin.com
Update a little bit the content to match the bus binding, including:
- the node title should have been named after the description done
in the historical i3c.txt file, ie: i3c-master@<address>
- child nodes should be accepted even though the drivers do not currently
support it
- #address-cells and #size-cells are also mandatory and have specific
values
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-3-miquel.raynal@bootlin.com
Attempting a conversion of the i3c.txt file to yaml schema with
minimal content changes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-2-miquel.raynal@bootlin.com
Michael Kerrisk suggested that, from an API perspective, it is a bad
idea to share the PR_SYS_DISPATCH_ defines between the prctl operation
and the selector variable.
Therefore, define two new constants to be used by SUD's selector variable
and update the corresponding documentation and test cases.
While this changes the API syscall user dispatch has never been part of a
Linux release, it will show up for the first time in 5.11.
Suggested-by: Michael Kerrisk (man-pages) <mtk.manpages@gmail.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210205184321.2062251-1-krisman@collabora.com
Commit 2991552447 ("entry: Drop usage of TIF flags in the generic syscall
code") introduced a bug on architectures using the generic syscall entry
code, in which processes stopped by PTRACE_SYSCALL do not trap on syscall
return after receiving a TIF_SINGLESTEP.
The reason is that the meaning of TIF_SINGLESTEP flag is overloaded to
cause the trap after a system call is executed, but since the above commit,
the syscall call handler only checks for the SYSCALL_WORK flags on the exit
work.
Split the meaning of TIF_SINGLESTEP such that it only means single-step
mode, and create a new type of SYSCALL_WORK to request a trap immediately
after a syscall in single-step mode. In the current implementation, the
SYSCALL_WORK flag shadows the TIF_SINGLESTEP flag for simplicity.
Update x86 to flip this bit when a tracer enables single stepping.
Fixes: 2991552447 ("entry: Drop usage of TIF flags in the generic syscall code")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kyle Huey <me@kylehuey.com>
Link: https://lore.kernel.org/r/87h7mtc9pr.fsf_-_@collabora.com
The ftrace event subsystem is only created for showing the format files of
events created by the ftrace tracers, and are not trace events. The ftrace
subsystem currently has both the "enable" and "filter" files that in other
subsystems are used to enable/disable all events within the subsystem or set
a filter for all the subsystem events.
As ftrace subsystem events do not use enable or filter operations, these
files are useless in the ftrace subsystem. Remove them.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The use of strncpy is discouraged, use strscpy instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media device has to be initialized and assigned to adapter->mdev
before the dvb devices are created, since that will trigger the
automatic creation of the topology.
Rework this code to achieve this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
YUV 4:4:4 is not subsampled, fix this in the docs.
Fixes: da785536e0 ("media: doc: pixfmt-yuv: Move all semi-planar YUV formats to common file")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the first IR message, interrupts are no longer received. In addition,
the code generates a timeout IR message of 10ms but sets the timeout value
to 100ms, so no timeout was ever generated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204317
Fixes: a49a7a4635 ("media: smipcie: add universal ir capability")
Tested-by: Laz Lev <lazlev@web.de>
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge USB QuadHD contains two two-tuner em28xx
devices behind a usb hub. Each of the four dvb adapters
contains a MaxLinear 692 combo ATSC demod/tuner.
Bus 003 Device 006: ID 2040:846d Hauppauge
Bus 003 Device 005: ID 2040:846d Hauppauge
Bus 003 Device 004: ID 04e2:0404 Exar Corp.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read errors are currently reported as write errors.
An incorrectly received read operation is never reported at all.
Add a debug statement indicating the request mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TS2 active led is completely igored, fix that.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MaxLinear 692 is a combo demod/tuner which has ATSC and QAM
capabilities. Only ATSC is currently advertised via DVB
properties. QAM still has issues.
Confirmed working on both big and little endian. Big
endian verified on PowerPC Mac mini.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit 1abdfe706a.
This change is broken and not solving any problem it claims to solve.
Robin reported that cpumask_local_spread() now returns any cpu out of
cpu_possible_mask in case that NOHZ_FULL is disabled (runtime or compile
time). It can also return any offline or not-present CPU in the
housekeeping mask. Before that it was returning a CPU out of
online_cpu_mask.
While the function is racy against CPU hotplug if the caller does not
protect against it, the actual use cases are not caring much about it as
they use it mostly as hint for:
- the user space affinity hint which is unused by the kernel
- memory node selection which is just suboptimal
- network queue affinity which might fail but is handled gracefully
But the occasional fail vs. hotplug is very different from returning
anything from possible_cpu_mask which can have a large amount of offline
CPUs obviously.
The changelog of the commit claims:
"The current implementation of cpumask_local_spread() does not respect
the isolated CPUs, i.e., even if a CPU has been isolated for Real-Time
task, it will return it to the caller for pinning of its IRQ
threads. Having these unwanted IRQ threads on an isolated CPU adds up
to a latency overhead."
The only correct part of this changelog is:
"The current implementation of cpumask_local_spread() does not respect
the isolated CPUs."
Everything else is just disjunct from reality.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: abelits@marvell.com
Cc: davem@davemloft.net
Link: https://lore.kernel.org/r/87y2g26tnt.fsf@nanos.tec.linutronix.de
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge misc fixes from Andrew Morton:
"18 patches.
Subsystems affected by this patch series: mm (hugetlb, compaction,
vmalloc, shmem, memblock, pagecache, kasan, and hugetlb), mailmap,
gcov, ubsan, and MAINTAINERS"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS/.mailmap: use my @kernel.org address
mm: hugetlb: fix missing put_page in gather_surplus_pages()
ubsan: implement __ubsan_handle_alignment_assumption
kasan: make addr_has_metadata() return true for valid addresses
kasan: add explicit preconditions to kasan_report()
mm/filemap: add missing mem_cgroup_uncharge() to __add_to_page_cache_locked()
mailmap: add entries for Manivannan Sadhasivam
mailmap: fix name/email for Viresh Kumar
memblock: do not start bottom-up allocations with kernel_end
mm: thp: fix MADV_REMOVE deadlock on shmem THP
init/gcov: allow CONFIG_CONSTRUCTORS on UML to fix module gcov
mm/vmalloc: separate put pages and flush VM flags
mm, compaction: move high_pfn to the for loop scope
mm: migrate: do not migrate HugeTLB page whose refcount is one
mm: hugetlb: remove VM_BUG_ON_PAGE from page_huge_active
mm: hugetlb: fix a race between isolating and freeing page
mm: hugetlb: fix a race between freeing and dissolving the page
mm: hugetlbfs: fix cannot migrate the fallocated HugeTLB page
Since commit 9ed5af268e ("SUNRPC: Clean up the handling of page
padding in rpc_prepare_reply_pages()") [Dec 2020] the NFS client
passes payload data to the transport with the padding in xdr->pages
instead of in the send buffer's tail kvec. There's no need for the
extra logic to advance the base of the tail kvec because the upper
layer no longer places XDR padding there.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The file /sys/kernel/tracing/events/enable is used to enable all events by
echoing in "1", or disabling all events when echoing in "0". To know if all
events are enabled, disabled, or some are enabled but not all of them,
cating the file should show either "1" (all enabled), "0" (all disabled), or
"X" (some enabled but not all of them). This works the same as the "enable"
files in the individule system directories (like tracing/events/sched/enable).
But when all events are enabled, the top level "enable" file shows "X". The
reason is that its checking the "ftrace" events, which are special events
that only exist for their format files. These include the format for the
function tracer events, that are enabled when the function tracer is
enabled, but not by the "enable" file. The check includes these events,
which will always be disabled, and even though all true events are enabled,
the top level "enable" file will show "X" instead of "1".
To fix this, have the check test the event's flags to see if it has the
"IGNORE_ENABLE" flag set, and if so, not test it.
Cc: stable@vger.kernel.org
Fixes: 553552ce17 ("tracing: Combine event filter_active and enable into single flags field")
Reported-by: "Yordan Karadzhov (VMware)" <y.karadz@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0
is invalid"), having a linux-irq with number 0 will trigger a WARN()
when calling platform_get_irq*() to retrieve that linux-irq.
Since [devm_]irq_alloc_desc allocs a single irq and since irq 0 is not used
on some systems, it can return 0, triggering that WARN(). This happens
e.g. on Intel Bay Trail and Cherry Trail devices using the LPE audio engine
for HDMI audio:
0 is an invalid IRQ number
WARNING: CPU: 3 PID: 472 at drivers/base/platform.c:238 platform_get_irq_optional+0x108/0x180
Modules linked in: snd_hdmi_lpe_audio(+) ...
Call Trace:
platform_get_irq+0x17/0x30
hdmi_lpe_audio_probe+0x4a/0x6c0 [snd_hdmi_lpe_audio]
---[ end trace ceece38854223a0b ]---
Change the 'from' parameter passed to __[devm_]irq_alloc_descs() by the
[devm_]irq_alloc_desc macros from 0 to 1, so that these macros will no
longer return 0.
Fixes: a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201221185647.226146-1-hdegoede@redhat.com
The check for a NULL pf pointer is moot since the earlier declaration and
assignment of struct device *dev already de-referenced the pointer. Also,
the only caller of ice_set_dflt_mib() already ensures pf is not NULL.
Cc: Dave Ertman <david.m.ertman@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex_array_size() helper with the recently added flexible array
members in structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>