No functional change. Since the reset controls obtained in
Sierra is exclusively used by the Sierra device, use
exclusive reset control request API calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-8-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Group devm_reset_control_get() and
devm_reset_control_get_optional() to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-7-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Group all devm_clk_get_optional() to a
separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-6-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
"serdes" node (child node of WIZ) can have sub-nodes for representing links
or it can have sub-nodes for representing the various clocks within the
serdes. Instead of trying to read "reg" from every child node used for
assigning "lane_phy_type", read only if the child node's name is "phy"
or "link" subnode.
Ideally all PHY dt nodes should have node name as "phy", however
existing devicetree used "link" as subnode. So in order to maintain old
DT compatibility get PHY properties for "phy" or "link" subnode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210319124128.13308-5-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cadence Sierra PHY driver registers PHY using devm_phy_create()
for all sub-nodes of Sierra device tree node. However Sierra device
tree node can have sub-nodes for the various clocks in addtion to the
PHY. Use devm_phy_create() only for nodes with name "phy" (or "link"
for old device tree) which represent the actual PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Invoke wiz_init() before configuring anything else in Sierra/Torrent
(invoked as part of of_platform_device_create()). wiz_init() resets the
SERDES device and any configuration done in the probe() of
Sierra/Torrent will be lost. In order to prevent SERDES configuration
from getting reset, invoke wiz_init() immediately before invoking
of_platform_device_create().
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Cc: <stable@vger.kernel.org> # v5.10
Link: https://lore.kernel.org/r/20210319124128.13308-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
de-asserts PHY_RESET even before the configurations are loaded in
phy_init(). However PHY_RESET should be de-asserted only after
all the configurations has been initialized, instead of de-asserting
in probe. Fix it here.
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The k[un]map() calls in ext2_[get|put]_page() are localized to a single
thread. kmap_local_page() is more efficient.
Replace the kmap/kunmap calls with kmap_local_page()/kunmap_local().
kunmap_local() requires the mapping address so return that address from
ext2_get_page() to be used in ext2_put_page(). This works well because
many of the callers need the address anyway so it is not bad to return
it along with the page.
In addition, kmap_local_page()/kunmap_local() require strict nesting
rules to be followed.
Document the new nesting requirements of ext2_get_page() and
ext2_put_page() as well as the relationship between ext2_get_page(),
ext2_find_entry(), and ext2_dotdot().
Adjust one ext2_put_page() call site in ext2_rename() to ensure the new
nesting requirements are met.
Finally, adjust code style for checkpatch.
To: Jan Kara <jack@suse.com>
Link: https://lore.kernel.org/r/20210329065402.3297092-3-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
ext2_dotdot() and ext2_find_entry() both require ext2_put_page() to be
called after successful return. For some of the calls this
corresponding put was hidden in ext2_set_link and ext2_delete_entry().
Match up ext2_put_page() with ext2_dotdot() and ext2_find_entry() in the
functions which call them. This makes the code easier to follow
regarding the get/put of the page.
Clean up comments to match new behavior.
To: Jan Kara <jack@suse.com>
Link: https://lore.kernel.org/r/20210329065402.3297092-2-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Kakadu is also known as ASUS Chromebook Detachable CM3.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331091327.1198529-3-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are some Mediatek based Chromebooks supported in the kernel. Enable the
required config options to have the panel display working on both devices.
This was tested on the ACER Chromebook R13 (MT8173) and the Lenovo
Ideapad Duet (MT8183), but should also enable display support for similar
devices.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331090659.4169966-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the option necessary to boot mt8173-based boards to boot from
usb devices, like its phy and the regulators needed to have proper
support.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331090659.4169966-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Compilation fails when KVM is selected and ARM64_SVE isn't.
The root cause is that sve_cond_update_zcr_vq is not defined when
ARM64_SVE is not selected. Fix it by adding an empty definition
when CONFIG_ARM64_SVE=n.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
[maz: simplified commit message, fleshed out dummy #define]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1617183879-48748-1-git-send-email-tanxiaofei@huawei.com
Add the check if source control mode is supported by the
PCON, before starting configuring PCON for FRL training,
as per spec VESA DP2.0-HDMI2.1 PCON Draft-1 Sec-7.
v2: Added spec details for the change. (Uma)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210323112422.1211-3-ankit.k.nautiyal@intel.com
In commit e2dcd20b16 a change was made to use
devm_platform_ioremap_resource_byname() to simplify code and remove
the res variable; this was wrong since the res variable is still needed
and as an outcome the port->cfg_addr gets an erroneous address.
Revert the change going back to original behaviour.
Link: https://lore.kernel.org/r/20210328144118.305074-1-zhengdejin5@gmail.com
Fixes: e2dcd20b16 ("PCI: controller: Convert to devm_platform_ioremap_resource_byname()")
Reported-by: dann.frazier@canonical.com
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.9+
Currently the FRL training mode (Concurrent, Sequential) and
training type (Normal, Extended) are not defined properly and
are passed as bool values in drm_helpers for pcon
configuration for FRL training.
This patch:
-Add register masks for Sequential and Normal FRL training options.
-Fixes the drm_helpers for FRL Training configuration to use the
appropriate masks.
-Modifies the calls to the above drm_helpers in i915/intel_dp as per
the above change.
v2: Re-used the register masks for these options, instead of enum. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210323112422.1211-2-ankit.k.nautiyal@intel.com
We can advertise ourselves to guests as KVM and provide a basic features
bitmap for discoverability of future hypervisor services.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-3-jianyong.wu@arm.com
Although the SMCCC specification provides some limited functionality for
describing the presence of hypervisor and firmware services, this is
generally applicable only to functions designated as "Arm Architecture
Service Functions" and no portable discovery mechanism is provided for
standard hypervisor services, despite having a designated range of
function identifiers reserved by the specification.
In an attempt to avoid the need for additional firmware changes every
time a new function is added, introduce a UID to identify the service
provider as being compatible with KVM. Once this has been established,
additional services can be discovered via a feature bitmap.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
[maz: move code to its own file, plug it into PSCI]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-2-jianyong.wu@arm.com
The sparse tool complains as follows:
arch/arm64/kvm/arm.c:1900:6: warning:
symbol '_kvm_host_prot_finalize' was not declared. Should it be static?
This symbol is not used outside of arm.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xu Jia <xujia39@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1617176179-31931-1-git-send-email-xujia39@huawei.com
s/Hisilicon/HiSilicon/g.
It should use capital S, according to
https://www.hisilicon.com/en/terms-of-use.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I dunno why I got added here, but I haven't been using this driver for
years. Remove me to make space for interested parties.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c_recover_bus() returns -EOPNOTSUPP if bus recovery isn't wired up
by the bus driver, which the case for Tegra I2C driver for example. This
error code is then propagated to I2C client and might be confusing, thus
make i2c_recover_bus() to return -EBUSY instead.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the following coccicheck report:
drivers/i2c/busses/i2c-stm32f7.c:2032:3-10 : platform_get_irq :
line 2032 is redundant because platform_get_irq() already prints an error
Remove dev_err() messages after platform_get_irq() failures.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Inspect a message's return value upon successful IVC transaction to
determine if the I2C transaction on the BPMP side was successful.
Heavily based on work by Timo Alho <talho@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Only send "X1000_I2C_DC_STOP" when last byte, or it will cause
error when I2C write operation which should look like this:
device_addr + w, reg_addr, data;
But without this patch, it looks like this:
device_addr + w, reg_addr, device_addr + w, data;
Fixes: 21575a7a8d ("I2C: JZ4780: Add support for the X1000.")
Reported-by: 杨文龙 (Yang Wenlong) <ywltyut@sina.cn>
Tested-by: 杨文龙 (Yang Wenlong) <ywltyut@sina.cn>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for arch/arm/mach-omap1/timer.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for OMAP1 Dual(). Prototype was for OMAP1610_GPTIMER1_BASE() instead"
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for arch/arm/mach-omap2/omap_twl.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: wrong kernel-doc identifier on line:
* OMAP and TWL PMIC specific initializations."
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lifu Chen <chenlifu@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on linux-gpio discussion [1], it is best practice to make the
gpio-line-names unique. Generic names like "[ethernet]" are replaced
with the name of the unique signal on the AM3358 SoC ball corresponding
to the gpio line. "[NC]" is also renamed to the standard "NC" name to
represent "not connected".
[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 675bceb097 ("powerpc/mm: Remove DEBUG_VM_PGTABLE support on powerpc")
All the related issues are fixed as of commit:
f14312e1ed ("mm/debug_vm_pgtable: avoid doing memory allocation with pgtable_t mapped.")
Hence re-enable it.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210318034855.74513-1-aneesh.kumar@linux.ibm.com
The newly introduced -s command line option starts an interactive shell.
If a command is specified, the shell is started after the command
finishes executing. It's useful to have a shell especially when
debugging failing tests or developing new tests.
Since the user may terminate the VM forcefully, an extra "sync" is added
after the execution of the command to persist any logs from the command
into the log file.
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210323014752.3198283-1-kpsingh@kernel.org
When we mount an unclean f2fs image in a readonly block device, let's
make mount() succeed only when there is no recoverable data in that
image, otherwise after mount(), file fsyned won't be recovered as user
expected.
Fixes: 938a184265 ("f2fs: give a warning only for readonly partition")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The vio bus is a fake bus, which we use on pseries LPARs (guests) to
discover devices provided by the hypervisor. There's no need or sense
in creating the vio bus on bare metal systems.
Which is why commit 4336b93378 ("powerpc/pseries: Make vio and
ibmebus initcalls pseries specific") made the initialisation of the
vio bus only happen in LPARs.
However as a result of that commit we now see errors at boot on bare
metal systems:
Driver 'hvc_console' was unable to register with bus_type 'vio' because the bus was not initialized.
Driver 'tpm_ibmvtpm' was unable to register with bus_type 'vio' because the bus was not initialized.
This happens because those drivers are built-in, and are calling
vio_register_driver(). It in turn calls driver_register() with a
reference to vio_bus_type, but we haven't registered vio_bus_type with
the driver core.
Fix it by also guarding vio_register_driver() with a check to see if
we are on pseries.
Fixes: 4336b93378 ("powerpc/pseries: Make vio and ibmebus initcalls pseries specific")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20210316010938.525657-1-mpe@ellerman.id.au
As recommended by Stephen Boyd, convert the Agilex/Stratix10/n5x clock
driver to use the clk_hw registration method.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210302214151.1333447-3-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As recommended by Stephen Boyd, convert the Arria10 clock driver to use
the clk_hw registration method.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210302214151.1333447-2-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As recommended by Stephen Boyd, convert the cyclone5/arria5 clock driver
to use the clk_hw registration method.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210302214151.1333447-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Iff platform_get_irq() returns 0, ahci_platform_init_host() would return 0
early (as if the call was successful). Override IRQ0 with -EINVAL instead
as the 'libata' regards 0 as "no IRQ" (thus polling) anyway...
Fixes: c034640a32 ("ata: libahci: properly propagate return value of platform_get_irq()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/4448c8cc-331f-2915-0e17-38ea34e251c8@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638 ("sata_mv: Support SoC controllers")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/ata/pata_acpi.c:38: warning: Function parameter or member 'link' not described in 'pacpi_pre_reset'
drivers/ata/pata_acpi.c:38: warning: Excess function parameter 'ap' description in 'pacpi_pre_reset'
drivers/ata/pata_acpi.c:74: warning: Function parameter or member 'ap' not described in 'pacpi_discover_modes'
drivers/ata/pata_acpi.c:74: warning: Excess function parameter 'mask' description in 'pacpi_discover_modes'
drivers/ata/pata_acpi.c:239: warning: Function parameter or member 'id' not described in 'pacpi_init_one'
drivers/ata/pata_acpi.c:239: warning: Excess function parameter 'ent' description in 'pacpi_init_one'
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210318085150.3131936-16-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/ata/libata-acpi.c:493: warning: expecting prototype for ata_acpi_gtm_xfermode(). Prototype was for ata_acpi_gtm_xfermask() instead
drivers/ata/libata-acpi.c:648: warning: Function parameter or member 'prev_gtf' not described in 'ata_acpi_run_tf'
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210318085150.3131936-15-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/ata/sata_mv.c:1929: warning: expecting prototype for mv_bmdma_stop(). Prototype was for mv_bmdma_stop_ap() instead
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mark Lord <mlord@pobox.com>
Cc: ALWAYS copy <linux-ide@vger.kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210318085150.3131936-14-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>