The voltage default on the AB8500 VAUX1 regulator is way
too low and does not correspond to the setting in the
vendor tree. This should be 2.8-3.3 V not 2.5-2.9 V or
things like the HREFP520 touchscreen will not work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
D_CAN controller supports 16, 32, 64 or 128 message objects, comparing
to 32 on C_CAN. AM335x/AM437x Sitara processors and DRA7 SOC all
instantiate a D_CAN controller with 64 message objects, as described
in the "DCAN features" subsection of the CAN chapter of their
technical reference manuals.
The driver policy has been kept unchanged, and as in the previous
version, the first half of the message objects is used for reception
and the second for transmission.
The I/O load is increased only in the case of 64 message objects,
keeping it unchanged in the case of 32. Two 32-bit read accesses are
in fact required, which however remained at 16-bit for configurations
with 32 message objects.
Link: https://lore.kernel.org/r/20210302215435.18286-7-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As pointed by commit c0a9f4d396 ("can: c_can: Reduce register
access") the "driver casts the 16 message objects in stone, which is
completely braindead as contemporary hardware has up to 128 message
objects".
The patch prepares the module to extend the number of message objects
beyond the 32 currently managed. This was achieved by transforming the
constants used to manage RX/TX messages into variables without
changing the driver policy.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210302215435.18286-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The arbitration register is already set up with 32-bit writes in the
other parts of the code except for this point.
Link: https://lore.kernel.org/r/20210302215435.18286-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After reading the commit 640916db2b ("can: c_can: Make it SMP safe")
it may sound strange to see the IF_RX interface used by the
can_inval_tx_object function. A comment was added to avoid any
misunderstanding.
Link: https://lore.kernel.org/r/20210302215435.18286-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 9d23a9818c ("can: c_can: Remove unused inline function") left
behind C_CAN_MSG_OBJ_TX_LAST constant.
Commit fa39b54ccf ("can: c_can: Get rid of pointless interrupts") left
behind C_CAN_MSG_RX_LOW_LAST and C_CAN_MSG_OBJ_RX_SPLIT constants.
The removed code also made a comment useless and misleading.
Link: https://lore.kernel.org/r/20210302215435.18286-2-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses the previously added mcp251xfd_skb_set_timestamp()
function to convert the timestamp done by the CAN controller into a
proper skb hw timestamp.
Link: https://lore.kernel.org/r/20210304161209.2754463-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add the HW timestamping infrastructure. The mcp251xfd has a
free running timer of 32 bit width, running at max 40MHz, which wraps
around every 107 seconds. The current timestamp is latched into RX and
TEF objects automatically be the CAN controller.
This patch sets up a cyclecounter, timecounter and delayed worker
infrastructure (which runs every 45 seconds) to convert the timer into
a proper 64 bit based ns timestamp.
Link: https://lore.kernel.org/r/20210304160328.2752293-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the patches:
| 1f652bb6ba can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit
| 68c0c1c7f9 can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit
the setting of the UINC bit in the TEF and RX FIFO was batched into a
single SPI message consisting of several transfers. All transfers but
the last need to have the cs_change set to 1.
In the original patches the array of prepared transfers is send from
the beginning with the length depending on the number of read TEF/RX
objects. The cs_change of the last transfer is temporarily set to
0 during send.
This patch removes the modification of cs_change by preparing the last
transfer with cs_change to 0 and all other to 1. When sending the SPI
message the driver now starts with an offset into the array, so that
it always ends on the last entry in the array, which has the cs_change
set to 0.
Link: https://lore.kernel.org/r/20210304160328.2752293-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For easier debugging this patch adds dev coredump support to the
driver. A dev coredump is generated in case the chip fails to start or
an error in the interrupt handler is detected.
The dev coredump consists of all chip registers and chip memory, as
well as the driver's internal state of the TEF-, RX- and TX-FIFOs, it
can be analyzed with the mcp251xfd-dump tool of the can-utils:
https://github.com/linux-can/can-utils/tree/master/mcp251xfd
Link: https://lore.kernel.org/r/20210304160328.2752293-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
linux/regmap.h has been included at line 13, so remove the duplicate
one at line 14.
Fixes: 67def4ef8b ("can: tcan4x5x: move regmap code into seperate file")
Link: https://lore.kernel.org/r/20210323021026.140460-1-wanjiabing@vivo.com
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For peripheral devices, m_can sent skbs directly from a threaded irq
instead of from a softirq context, breaking the tcan4x5x peripheral
driver completely. This patch transitions the driver to use the
rx-offload helper for peripherals, ensuring the skbs are sent from the
correct context, with h/w timestamping to ensure correct ordering.
Link: https://lore.kernel.org/r/20210308102427.63916-4-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
[mkl: m_can_class_register(): update error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a prerequisite for transitioning the m_can driver to rx-offload,
which works best with TX and RX timestamps.
The timestamps provided by M_CAN are 16-bit, timed according to the
nominal bit timing, and may be prescaled by a multiplier up to 16. We
choose the highest prescalar so that the timestamp wraps every 2^20 bit
times, or 209 ms at a bus speed of 5 Mbit/s. Timestamps will have a
precision of 16 bit times.
Link: https://lore.kernel.org/r/20210308102427.63916-3-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the CAN net device has been successfully allocated, its private
data structure is impossible to be empty, remove this redundant error
return judgment.
Link: https://lore.kernel.org/r/20210205072559.13241-2-xulin.sun@windriver.com
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds "ONE-SHOT" mode support to the following CAN-USB
PEAK-System GmbH interfaces:
- PCAN-USB X6
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-Chip USB
- PCAN-USB Pro
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes it possible to specifically flash the LED of a CAN
port of the CAN-USB interfaces of PEAK-System.
Link: https://lore.kernel.org/r/20210309122141.3276927-1-mkl@pengutronix.de
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: use common prefix PCAN_ for defines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the plain integers used for flags in
pcan_usb_pro_encode_msg() by macros which are already defined.
Link: https://lore.kernel.org/r/20210309082128.23125-4-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
struct ucan_message_in contains member with 4-byte alignment
but is itself marked as unaligned, which triggers a warning:
drivers/net/can/usb/ucan.c:249:1: warning: alignment 1 of 'struct ucan_message_in' is less than 4 [-Wpacked-not-aligned]
Mark the outer structure to have the same alignment as the inner
one.
Link: https://lore.kernel.org/r/20210204162625.3099392-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On ARCHs without IOMEM support the grcan driver fails to link due to
missing iomem functionality. This patch adds the missing Kconfig
dependency to HAS_IOMEM.
Link: https://lore.kernel.org/r/20210309140424.3331010-1-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add three macro to simplify the readability of big bit timing numbers:
- CAN_KBPS: kilobits per second (one thousand)
- CAN_MBPS: megabits per second (one million)
- CAN_MHZ: megahertz per second (one million)
Example:
u32 bitrate_max = 8 * CAN_MBPS;
struct can_clock clock = {.freq = 80 * CAN_MHZ};
instead of:
u32 bitrate_max = 8000000;
struct can_clock clock = {.freq = 80000000};
Apply the new macro to driver/net/can/dev/bittiming.c.
Link: https://lore.kernel.org/r/20210306054040.76483-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The logic for the tdco calculation is to just reuse the normal sample
point: tdco = sp. Because the sample point is expressed in tenth of
percent and the tdco is expressed in time quanta, a conversion is
needed.
At the end,
ssp = tdcv + tdco
= tdcv + sp.
Another popular method is to set tdco to the middle of the bit:
tdc->tdco = can_bit_time(dbt) / 2
During benchmark tests, we could not find a clear advantages for one
of the two methods.
The tdco calculation is triggered each time the data_bittiming is
changed so that users relying on automated calculation can use the
netlink interface the exact same way without need of new parameters.
For example, a command such as:
ip link set canX type can bitrate 500000 dbitrate 4000000 fd on
would trigger the calculation.
The user using CONFIG_CAN_CALC_BITTIMING who does not want automated
calculation needs to manually set tdco to zero.
For example with:
ip link set canX type can tdco 0 bitrate 500000 dbitrate 4000000 fd on
(if the tdco parameter is provided in a previous command, it will be
overwritten).
If tdcv is set to zero (default), it is automatically calculated by
the transiver for each frame. As such, there is no code in the kernel
to calculate it.
tdcf has no automated calculation functions because we could not
figure out a formula for this parameter.
Link: https://lore.kernel.org/r/20210224002008.4158-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix the warning triggered by having an '=' at the beginning of the
line by moving it back to the previous line. Also replace all
indentations with a single space so that future entries can be more
easily added.
Extract of ./scripts/checkpatch.pl -f drivers/net/can/dev/netlink.c:
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING]
+ = { .len = sizeof(struct can_bittiming) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
Link: https://lore.kernel.org/r/20210224002008.4158-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
| 9420e1d495 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A out of bounds access to "struct can_priv::echo_skb" leads to a
kernel crash. Better print a sensible warning message instead and try
to recover.
This patch is similar to:
| e7a6994d04 ("can: dev: __can_get_echo_skb(): Don't crash the kernel
| if can_priv::echo_skb is accessed out of bounds")
Link: https://lore.kernel.org/r/20210319142700.305648-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Actually, setting the registers for routing, use multiple 'if-else' for different
routes, but this code would be more and more complicated while we
support more and more SoCs. Change that and use a table per SoC so the
code will be more portable and clear.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210317181711.795245-3-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Apart from the driver data, in order to extend the driver to support more
and more SoCs, we will need to store other configuration data. So, create
a mtk_mmsys struct to encapsulate all that information.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20210317181711.795245-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We sometimes see COMMAND_IGNORED responses during the clock stop
sequence. It turns out we already have information if devices are
present on a link, so we should only prepare those when they
are attached.
In addition, even when COMMAND_IGNORED are received, we should still
proceed with the clock stop. The device will not be prepared but
that's not a problem.
The only case where the clock stop will fail is if the Cadence IP
reports an error (including a timeout), or if the devices throw a
COMMAND_FAILED response.
BugLink: https://github.com/thesofproject/linux/issues/2621
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323013707.21455-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code makes no sense, we multiply a channel number by
zero (SDW_BLK_GRP_CNT_1), and the result is used to configure the
block packing mode. Sampling grouping and channel packing are two
separate concepts in SoundWire.
In addition, the bandwidth allocation allocates a vertical slice for
each stream, which makes the use of the PER_CHANNEL packing mode
irrelevant.
Let's use the proper definition for block packing mode (PER_PORT).
This change has no functional impact though since the net result is
the same configuration of the DPN_BlockCtrl3 register, when
implemented.
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323050701.23760-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some reason we don't have an enum for this concept. Add
definitions following Table 102 of the SoundWire 1.2 specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323050701.23760-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When Secure World returns, it may have changed the size attribute of the
memory references passed as [in/out] parameters. The GlobalPlatform TEE
Internal Core API specification does not restrict the values that this
size can take. In particular, Secure World may increase the value to be
larger than the size of the input buffer to indicate that it needs more.
Therefore, the size check in optee_from_msg_param() is incorrect and
needs to be removed. This fixes a number of failed test cases in the
GlobalPlatform TEE Initial Configuratiom Test Suite v2_0_0_0-2017_06_09
when OP-TEE is compiled without dynamic shared memory support
(CFG_CORE_DYN_SHM=n).
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Suggested-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Jerome Forissier <jerome@forissier.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to a hardware bug preventing the correct detection if the ID pin
the USB OTG port cannot be used in otg mode. It can either be set to
host or peripheral. Set it to peripheral so vbus is disabled by default.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmuxing for the enable pin of the usbh1 node is wrong. It needs to
be muxed as GPIO. While at it, move the pinctrl to the vbus regulator
since it is actually the regulator enable pin.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As clk_core_populate_parent_map() checks clk_init_data.num_parents
first, and checks clk_init_data.parent_names[] before
clk_init_data.parent_data[] and clk_init_data.parent_hws[], leaving the
latter uninitialized doesn't do harm for now. However, it is better to
play it safe, and initialize all clk_init_data structures to zeroes, to
avoid any current and future members containing uninitialized data.
Remove a few explicit zero initializers, which are now superfluous.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210326105434.1574796-1-geert+renesas@glider.be
drivers/hid/hid-thrustmaster.c:300:27-34: WARNING opportunity for kmemdup
Use kmemdup rather than duplicating its implementation
Generated by: scripts/coccinelle/api/memdup.cocci
Fixes: c49c336378 ("HID: support for initialization of some Thrustmaster wheels")
CC: Dario Pagani <dario.pagani.146@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>