Panel power sequence says timing T8 (time from link idle to turn on
the backlight) should be at least 50 ms. This is what the .enable
delay in simple-panel is for, so set it. NOTE: this overlaps with the
80 ms .prepare_to_enable delay on purpose. The data sheet says that
at least 80 ms needs to pass between HPD going high and turning on the
backlight and that at least 50 ms needs to pass between the link idle
and the backlight going on. Thus it works like this on the system in
front of me:
* In bridge chip pre_enable call drm_panel_prepare()
* drm_panel_prepare() -> panel_simple_prepare()
* Wait for HPD GPIO to go high.
* Start counting for 80 ms (store in prepared_time)
* In bridge chip enable, train link then call drm_panel_enable()
* drm_panel_enable() -> panel_simple_enable()
* panel_simple_enable() does hardcoded 50 ms delay then enforces 80 ms
from HPD going high (in case the bridge took less than 30 ms to
enable / link train).
* drm_panel_enable() -> backlight_enable().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222081716.1.I1a45aece5d2ac6a2e73bbec50da2086e43e0862b@changeid
The series reuses mt8183-mt6358-ts3a227-max98357.c for supporting
machine driver with rt1015p speaker amplifier.
The 1st patch adds document for the new proposed compatible string.
The 2nd patch changes the machine driver to support "RT1015P" codec.
Tzung-Bi Shih (2):
ASoC: dt-bindings: mt8183: add compatible string for using rt1015p
ASoC: mediatek: mt8183: support machine driver with rt1015p
.../sound/mt8183-mt6358-ts3a227-max98357.txt | 1 +
sound/soc/mediatek/Kconfig | 1 +
.../mt8183/mt8183-mt6358-ts3a227-max98357.c | 29 +++++++++++++++++++
3 files changed, 31 insertions(+)
--
2.31.0.rc2.261.g7f71774620-goog
This panel is quite similar to the similarly named N116BGE panel (the
nominal timings are, in fact identical). However, let's add a new
entry because the full range of clocks listed for N116BGE aren't
supported for N116BCA-EA1, at least according to the datasheet.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.5.I3c01f3aab8335cb509da7009d8938c1a27a266dc@changeid
On an Innolux N116BCA panel that I have in front of me, sometimes HPD
simply doesn't assert no matter how long you wait for it. As per the
very wise advice of The IT Crowd ("Have you tried turning it off and
on again?") it appears that power cycling is enough to kick this panel
back into a sane state.
>From tests on this panel, it appears that leaving it powered off for a
while stimulates the problem. Adding a 6 second sleep at the start of
panel_simple_prepare_once() makes it happen fairly reliably and, with
this delay, I saw up to 3 retries needed sometimes. Without the 6
second sleep, however, the panel came up much more reliably the first
time or after only 1 retry.
While it's unknown what the problems are with this panel (and probably
the hardware should be debugged), adding a few retries to the power on
routine doesn't seem insane. Even if this panel's problems are
attributed to the fact that it's pre-production and/or can be fixed,
retries clearly can help in some cases and really don't hurt.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.3.I6916959daa7c5c915e889442268d23338de17923@changeid
If a panel has an hpd_absent_delay specified then we know exactly how
long the maximum time is before HPD must be asserted. That means we
can use it as a timeout for polling the HPD pin instead of using an
arbitrary timeout. This is especially useful for dealing with panels
that periodically fail to power on and need to be retried. We can
detect the problem sooner.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.2.I183b1817610d7a82fdd3bc852e96d2985df9623f@changeid
If the HPD signal never asserts in panel_simple_prepare() and we
return an error, we should unset the enable GPIO and disable the
regulator to make it consistent for the caller.
At the moment I have some hardware where HPD sometimes doesn't assert.
Obviously that needs to be debugged, but this patch makes it so that
if I add a retry that I can make things work.
Fixes: 48834e6084 ("drm/panel-simple: Support hpd-gpios for delaying prepare()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.1.I33fcbd64ab409cfe4f9491bf449f51925a4d3281@changeid
When the server tries to do a callback and a client fails it due to
authentication problems, we need the server to set callback down
flag in RENEW so that client can recover.
Suggested-by: Bruce Fields <bfields@redhat.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Link: https://lore.kernel.org/linux-nfs/FB84E90A-1A03-48B3-8BF7-D9D10AC2C9FE@oracle.com/T/#t
Add ALTERNATIVE_TERNARY support for replacing an initial instruction
with either of two instructions depending on a feature:
ALTERNATIVE_TERNARY "default_instr", FEATURE_NR,
"feature_on_instr", "feature_off_instr"
which will start with "default_instr" and at patch time will,
depending on FEATURE_NR being set or not, patch that with either
"feature_on_instr" or "feature_off_instr".
[ bp: Add comment ontop. ]
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210311142319.4723-7-jgross@suse.com
Add support for alternative patching for the case a feature is not
present on the current CPU. For users of ALTERNATIVE() and friends, an
inverted feature is specified by applying the ALT_NOT() macro to it,
e.g.:
ALTERNATIVE(old, new, ALT_NOT(feature));
Committer note:
The decision to encode the NOT-bit in the feature bit itself is because
a future change which would make objtool generate such alternative
calls, would keep the code in objtool itself fairly simple.
Also, this allows for the alternative macros to support the NOT feature
without having to change them.
Finally, the u16 cpuid member encoding the X86_FEATURE_ flags is not an
ABI so if more bits are needed, cpuid itself can be enlarged or a flags
field can be added to struct alt_instr after having considered the size
growth in either cases.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210311142319.4723-6-jgross@suse.com
ext4 didn't properly clean up if verity failed to be enabled on a file:
- It left verity metadata (pages past EOF) in the page cache, which
would be exposed to userspace if the file was later extended.
- It didn't truncate the verity metadata at all (either from cache or
from disk) if an error occurred while setting the verity bit.
Fix these bugs by adding a call to truncate_inode_pages() and ensuring
that we truncate the verity metadata (both from cache and from disk) in
all error paths. Also rework the code to cleanly separate the success
path from the error paths, which makes it much easier to understand.
Reported-by: Yunlei He <heyunlei@hihonor.com>
Fixes: c93d8f8858 ("ext4: add basic fs-verity support")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210302200420.137977-2-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The time pvops functions are the only ones left which might be
used in 32-bit mode and which return a 64-bit value.
Switch them to use the static_call() mechanism instead of pvops, as
this allows quite some simplification of the pvops implementation.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210311142319.4723-5-jgross@suse.com
Some users of paravirtualized functions need to query which function
has been specified in a pv_ops vector element. In order to be able to
switch such paravirtualized functions to static_calls instead, there
needs to be a function to query the function which will be called via
static_call().
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210311142319.4723-4-jgross@suse.com
Having the definition of static_call() in static_call_types.h makes
no sense as long struct static_call_key isn't defined there, as the
generic implementation of static_call() is referencing this structure.
So move the definition of struct static_call_key to static_call_types.h.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210311142319.4723-3-jgross@suse.com
Merge arch/x86/include/asm/alternative-asm.h into
arch/x86/include/asm/alternative.h in order to make it easier to use
common definitions later.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210311142319.4723-2-jgross@suse.com
Ever since the addition of multipage bio_vecs BIO_MAX_PAGES has been
horribly confusingly misnamed. Rename it to BIO_MAX_VECS to stop
confusing users of the bio API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210311110137.1132391-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add pinmux details and device tree node for the EEPROM attached to SPI0
module in main domain.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210309162315.22743-1-a-govindraju@ti.com
TI J7200 has the Cadence OSPI controller for interfacing with OSPI
flashes. Add its node to allow using SPI flashes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-4-p.yadav@ti.com
Set the Tx bus width to 8 so 8D-8D-8D mode can be selected. Change the
frequency to 25 MHz. This is the frequency that the flash has been
successfully tested with in Octal DTR mode. The total performance should
still increase since 8D-8D-8D mode should be at least twice as fast as
1S-1S-8S mode.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-3-p.yadav@ti.com
Set the Tx bus width to 8 so 8D-8D-8D mode can be selected. Change the
frequency to 25 MHz. This is the frequency that the flash has been
successfully tested with in Octal DTR mode. The total performance should
still increase since 8D-8D-8D mode should be at least twice as fast as
1S-1S-8S mode.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-2-p.yadav@ti.com
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: cd48ce86a4 ("arm64: dts: ti: k3-j721e-common-proc-board: Add support for SD card UHS modes")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210305054104.10153-1-a-govindraju@ti.com
Add the DT entry for a watchdog based on RTI1.
On SR1.0 silicon, it requires additional firmware on the MCU R5F cores
to handle the expiry, e.g. https://github.com/siemens/k3-rti-wdt. As
this firmware will also lock the power domain to protect it against
premature shutdown, mark it shared.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/279c20fa-6e5e-4f88-9cd1-f76297a28a19@web.de
When initialize cadence qspi controller, it is need to set cqspi
to the driver_data field of struct device, because it will be
used in function cqspi_remove/suspend/resume(). Otherwise, there
will be a crash trace as below when invoking these finctions.
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210311091220.3615-1-Meng.Li@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When DMI information is not present, trying to assign the card long
name results in the following warning.
WARNING KERN tegra-audio-graph-card sound: ASoC: no DMI vendor name!
The initial solution suggested was to test if the card device is an
ACPI one. This causes a regression visible to userspace on all Intel
platforms, with UCM unable to load card profiles based on DMI
information: the card devices are not necessarily ACPI ones, e.g. when
the parent creates platform devices on Intel devices.
To fix this problem, this patch exports the existing dmi_available
variable and tests it in the ASoC core.
Fixes: c014170408 ("ASoC: soc-core: Prevent warning if no DMI table is present")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20210310193928.108850-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supports machine driver with rt1015p ("mt8183_mt6358_ts3a227_rt1015p").
Embeds in the existing mt8183-mt6358-ts3a227-max98357.c because they
share most of the code.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210311033151.1818603-3-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/wm_adsp.c:2092:9: warning: Identical condition and
return expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/wm_adsp.c:2070:6: note: If condition 'ret' is true,
the function will return/exit
if (ret)
^
sound/soc/codecs/wm_adsp.c:2092:9: note: Returning identical
expression 'ret'
return ret;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/wm8903.c:1552:11: style: Variable 'best_val' is
assigned a value that is never used. [unreadVariable]
best_val = ((clk_sys * 10) / bclk_divs[0].ratio) - bclk;
^
sound/soc/codecs/wm8903.c:1559:12: style: Variable 'best_val' is
assigned a value that is never used. [unreadVariable]
best_val = cur_val;
^
Indeed what matters in the code is the blck_div, the best_val is
assigned but never tested or used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck complains about some members not being used, but it's really
the entire structure that is never used anywhere.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These routines lost all existing users during the latest merge window so
we can remove them. This avoids the need to fix them in the context of
fixing a regression related to the ID map on 52-bit VA kernels.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210310171515.416643-3-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
52-bit VA kernels can run on hardware that is only 48-bit capable, but
configure the ID map as 52-bit by default. This was not a problem until
recently, because the special T0SZ value for a 52-bit VA space was never
programmed into the TCR register anwyay, and because a 52-bit ID map
happens to use the same number of translation levels as a 48-bit one.
This behavior was changed by commit 1401bef703 ("arm64: mm: Always update
TCR_EL1 from __cpu_set_tcr_t0sz()"), which causes the unsupported T0SZ
value for a 52-bit VA to be programmed into TCR_EL1. While some hardware
simply ignores this, Mark reports that Amberwing systems choke on this,
resulting in a broken boot. But even before that commit, the unsupported
idmap_t0sz value was exposed to KVM and used to program TCR_EL2 incorrectly
as well.
Given that we already have to deal with address spaces being either 48-bit
or 52-bit in size, the cleanest approach seems to be to simply default to
a 48-bit VA ID map, and only switch to a 52-bit one if the placement of the
kernel in DRAM requires it. This is guaranteed not to happen unless the
system is actually 52-bit VA capable.
Fixes: 90ec95cda9 ("arm64: mm: Introduce VA_BITS_MIN")
Reported-by: Mark Salter <msalter@redhat.com>
Link: http://lore.kernel.org/r/20210310003216.410037-1-msalter@redhat.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210310171515.416643-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Commit fd7732e033 ("fs/locks: create a tree of dependent requests.")
has put blocked locks into a tree.
So, with a for loop, we can't check all locks information.
To solve this problem, we should traverse the tree.
Signed-off-by: Luo Longjun <luolongjun@huawei.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible "mediatek,mt8192-dpi" for the mt8192 dpi.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For HSTX_CKLP_EN and DIS_EOT, use symbolized register
definition instead of magic number.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Update the mediatek,dpi binding to use the graph schema. Missed
this one from the mass conversion since it's not part of drm-misc.
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Jitao shi <jitao.shi@mediatek.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>