Document now hidable link speed modes for the LED netdev trigger.
Link speed modes are now showed only if the named network device
supports them and are hidden if not.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240111160501.1774-2-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
With the addition of more link speed mode to the netdev trigger, it was
pointed out that there may be a problem with bloating the attribute list
with modes that won't ever be supported by the trigger as the attached
device name doesn't support them.
To clear and address this problem, change the logic where these
additional trigger modes are listed.
Since the netdev trigger REQUIRE a device name to be set, attach to the
device name change function additional logic to parse the supported link
speed modes using ethtool APIs and show only the supported link speed
modes attribute.
Link speed attribute are refreshed on device_name set and on
NETDEV_CHANGE events.
This only apply to the link speed modes and every other mode is still
provided by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240111160501.1774-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
If a hw_control_trigger is defined, it's usually desirable to make it
the default trigger. Therefore make it the default trigger, except
the driver explicitly set a default trigger.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/f33543de-3800-488f-a779-1fa282614462@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Even if a trigger is set as default trigger for a LED device,
the respective trigger module (if built as module) isn't automatically
loaded by the kernel if the LED device is registered. I think we can
do better. Try to load the module asynchronously by alias
ledtrig:<trigger name>. This requires that such an alias is added to
relevant triggers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/79adb260-06ad-443a-a68e-abe4498c3298@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Update the pm8350c lpg_data struct so that pm8350c devices are treated as
PWM devices that support two-nvmem PPG scheme.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20231221185838.28440-8-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
On PMICs such as PM8350C, the pattern lookup table (LUT) is stored in a
separate SDAM from the one where the lpg per-channel data is stored.
Add support for PPG with a dedicated LUT SDAM while maintaining backward
compatibility for those targets that use only a single SDAM.
Co-developed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Signed-off-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20231221185838.28440-7-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
Update the pmi632 lpg_data struct so that pmi632 devices use PPG
for LUT pattern.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231221185838.28440-6-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
In some PMICs like pmi632, the pattern look up table (LUT) and LPG
configuration is stored in a single SDAM module instead of LUT
peripheral. This feature is called PPG. PPG uses Qualcomm Programmable
Boot Sequencer (PBS) inorder to trigger pattern sequences for PMICs.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231221185838.28440-5-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
Update leds-qcom-lpg binding to support LPG PPG.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231221185838.28440-3-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
The current codes uses the sw_control path in set_baseline_state() when
called from netdev_trig_activate() even if we're hw-controlled. This
may result in errors when led_set_brightness() is called because we may
not have set_brightness led ops (if hw doesn't support setting a "LED"
to ON). In addition this path may schedule trigger_data->work which
doesn't make sense when being hw-controlled.
Therefore set trigger_data->hw_control = true before calling
set_device_name() from netdev_trig_activate(). In this call chain we
have to prevent set_baseline_state() from being called, because this
would call hw_control_set(). Use led_cdev->trigger_data == NULL as
indicator for being called from netdev_trig_activate().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/d3f2859c-2673-401c-a4f7-fcaef2167991@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The expresswire module requires gpiolib, so anything selecting it
also needs this dependency:
WARNING: unmet direct dependencies detected for LEDS_EXPRESSWIRE
Depends on [n]: NEW_LEDS [=y] && GPIOLIB [=n]
Selected by [y]:
- LEDS_KTD2692 [=y] && NEW_LEDS [=y] && LEDS_CLASS_FLASH [=y] && OF [=y]
Fixes: e59a15af7aa6 ("leds: ktd2692: Convert to use ExpressWire library")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240213165602.2230970-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
KTD2801 is a LED backlight driver IC found in samsung,coreprimevelte.
The brightness can be set using PWM or the ExpressWire protocol. Add
support for the KTD2801.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-4-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
KTD2801 is a LED backlight driver IC found in samsung,coreprimevelte.
The brightness can be set using PWM or the ExpressWire protocol. Add
a DT binding for the KTD2801.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-3-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
The KTD2692 uses the ExpressWire protocol implemented in the newly
introduced ExpressWire library. Convert the driver to use the library.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-2-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
The ExpressWire protocol is shared between at least KTD2692 and KTD2801
with slight differences such as timings and the former not having a
defined set of pulses for enabling the protocol (possibly because it
does not support PWM unlike KTD2801). Despite these differences the
ExpressWire handling code can be shared between the two, so in
preparation for adding KTD2801 support introduce a library implementing
this protocol.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-1-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
Class-based client auto-detection has been considered a legacy mechanism
for 10 yrs now. See commit 0c17617008 ("i2c: add deprecation warning
for class based instantiation"). Change the documentation of how to
write an i2c client accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Have an actual mlx5_sd instance in the core device, and fix the getter
accordingly. This allows SD stuff to flow, the feature becomes supported
only here.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
1) Each TX TLS device offloaded context has its own TIS object. Extra work
is needed to get it working in a SD environment, where a stream can move
between different SQs (belonging to different mdevs).
2) Each RX TLS device offloaded context needs a DEK object from the DEK
pool.
Extra work is needed to get it working in a SD environment, as the DEK
pool currently falsely depends on TX cap, and is on the primary device
only.
Disallow this combination for now.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Each queue counter object counts some events (in hardware) for the RQs
that are attached to it, like events of packet drops due to no receive
WQE (rx_out_of_buffer).
Each RQ can be attached to a queue counter only within the same vhca. To
still cover all RQs with these counters, we create multiple instances,
one per vhca.
The result that's shown to the user is now the sum of all instances.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Implement driver support for the HW feature that allows RX steering of
one device to target other device's RQs.
In SD multi-pf netdev mode, we set the secondaries into silent mode,
disconnecting them from the network. This feature is then used to steer
traffic from the primary to the secondaries.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Distribute the channels between the different SD-devices to acheive
local numa node performance on multiple numas.
Each channel works against one specific mdev, creating all datapath
queues against it.
We distribute channels to mdevs in a round-robin policy.
Example for 2 mdevs and 6 channels:
+-------+---------+
| ch ix | mdev ix |
+-------+---------+
| 0 | 0 |
| 1 | 1 |
| 2 | 0 |
| 3 | 1 |
| 4 | 0 |
| 5 | 1 |
+-------+---------+
This round-robin distribution policy is preferred over another suggested
intuitive distribution, in which we first distribute one half of the
channels to mdev #0 and then the second half to mdev #1.
We prefer round-robin for a reason: it is less influenced by changes in
the number of channels. The mapping between channel index and mdev is
fixed, no matter how many channels the user configures. As the channel
stats are persistent to channels closure, changing the mapping every
single time would turn the accumulative stats less representing of the
channel's history.
Per-channel objects should stop using the primary mdev (priv->mdev)
directly, and instead move to using their own channel's mdev.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Traffic queues will be created on all devices, including the
secondaries. Create the needed core layer resources for them as well.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Integrate the SD library calls into the auxiliary_driver ops in
preparation for creating a single netdev for the multiple PFs belonging
to the same SD group.
SD is still disabled at this stage. It is enabled by a downstream patch
when all needed parts are implemented.
The netdev is created whenever the SD group, with all its participants,
are ready. It is later destroyed whenever any of the participating PFs
drops.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Print to kernel log when an SD group moves from/to ready state.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Implement the needed SD steering adjustments for the primary and
secondaries.
While the SD multiple PFs are used to avoid cross-numa memory, when it
comes to chip level all traffic goes only through the primary device.
The secondaries are forced to silent mode, to guarantee they are not
involved in any unexpected ingress/egress traffic.
In RX, secondary devices will not have steering objects. Traffic will be
steered from the primary device to the RQs of a secondary device using
advanced cross-vhca RX steering capabilities.
In TX, the primary creates a new TX flow table, which is aliased by the
secondaries.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use devcom to communicate between the different devices. Add a new
devcom component type for this.
Each device registers itself to the devcom component <SD, group ID>.
Once all devices of a component are registered, the component becomes
ready, and a primary device is elected.
In principle, any of the devices can act as a primary, they are all
capable, and a random election would've worked. However, we aim to
achieve predictability and consistency, hence each group always choses
the same device, with the lowest PCI BUS number, as primary.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add implementation for querying the MPIR register for Socket-Direct
attributes, and instantiating a SD struct accordingly.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add Socket-Direct API with empty/minimal implementation.
We fill-in the implementation gradually in downstream patches.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a cap bit in mcam_access_reg to check for MPIR support.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
I2C_M_RD is defined as and guaranteed to be 1 and 'flag & I2C_M_RD' is
one or zero. No need for an additional condition to obtain the value.
Signed-off-by: Hsin-Yu.Chen <harry021633@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
[wsa: slightly updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
This will report a build warning once we have: 806cb22702 ("kunit:
Annotate _MSG assertion variants with gnu printf specifiers").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: c70703320e ("drm/tests/drm_buddy: add alloc_range_bias test")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Link: https://lore.kernel.org/r/20240229095225.242795-2-matthew.auld@intel.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
There's no reason to proceed with applying workaround and initing
sysfs if we are going to abort the probe upon failure.
Fixes: e5a845fd8f ("drm/xe: Add sysfs entry for tile")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306203110.146387-1-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit af7b93d1d7)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH7ZpcWbFyOOp6OJbrB3Eaf9PW7cFAmXoPHUACgkQrB3Eaf9P
W7ehmxAAoemzwIDP0wcDi7U68Za7wBC7CbV6WoVmDNRsO+BwnqlCtd7+B9hi0Qd0
h+KCVYw5EbUJbsHcuefj/QMNO46ueZZLswRIEMKlkZOHdC8TTGzjYmjLnkOHKTCm
wpJ9QSrnBoy3MUcWbZCJh4BZXsTftbu1fHRWy9GdBERXYfHqWdQCq/ZMAgv3IwLF
KwZahoGZwCDkmWOpshbBRGj0lnONzZ3mW//bN5EB71rSi33gPEtABYBSw9E9sdMw
uZg/xRnHMhS5CQHRnFEqVUiqu3wDJYgs3kQIDFhC1T2w94GBF/R+HzzFiBKLzxr1
Dk17avoNexSYRThJfCk6fMbXT4GVaUSKSG6KI4CRLna/wAIb4QEVDPEdk1ybOxRy
eoUfo7GXkVqhJpqnOX0Sl3262DnhQ/syhmv3sWXmoSpa630mDuFleVuVJE81dtMu
jSfaXY7BNpEwTwj8kzabKq5cLkt4T4dAnXf0ao1ATNCzcFkUjSIWN5ylnOEtdVe/
wEZYp8oc1kPEDU0RC8LzpaEooTQlPceeIAZca7a/lAhnRreGyP9j56Y2oM9YS76o
JPRrznWAdXVa0gX81zGOjZDHWSyLgpJZ9z5MaAdquP9uhXS4buu+pxxoUcFEfLJd
FV+yY9j3o3l0HLL6j/y6EZy/QzWPV+K9NAhokNL/WTwuOZ2Lq5Y=
=FnLp
-----END PGP SIGNATURE-----
Merge tag 'ipsec-2024-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2024-03-06
1) Clear the ECN bits flowi4_tos in decode_session4().
This was already fixed but the bug was reintroduced
when decode_session4() switched to us the flow dissector.
From Guillaume Nault.
2) Fix UDP encapsulation in the TX path with packet offload mode.
From Leon Romanovsky,
3) Avoid clang fortify warning in copy_to_user_tmpl().
From Nathan Chancellor.
4) Fix inter address family tunnel in packet offload mode.
From Mike Yu.
* tag 'ipsec-2024-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: set skb control buffer based on packet offload as well
xfrm: fix xfrm child route lookup for packet offload
xfrm: Avoid clang fortify warning in copy_to_user_tmpl()
xfrm: Pass UDP encapsulation in TX packet offload
xfrm: Clear low order bits of ->flowi4_tos in decode_session4().
====================
Link: https://lore.kernel.org/r/20240306100438.3953516-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After 292fac464b ("net: ethtool: eee: Remove legacy _u32 from keee")
this function has no user any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b4ff9b51-092b-4d44-bfce-c95342a05b51@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch updates the mlxbf_gige driver to support the
"get_pause_stats()" callback, which enables display of
pause frame counters via "ethtool -I -a oob_net0".
The pause frame counters are only enabled if the "counters_en"
bit is asserted in the LLU general config register. The driver
will only report stats, and thus overwrite the default stats
state of ETHTOOL_STAT_NOT_SET, if "counters_en" is asserted.
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240305212137.3525-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel bot has discovered that if CONFIG_GPIOLIB is not set compilation
will fail.
Upon investigation the issue is that qca807x_gpio() is guarded by a
preprocessor check but then it is called under
if (IS_ENABLED(CONFIG_GPIOLIB)) in the probe call so the compiler will
error out since qca807x_gpio() has not been declared if CONFIG_GPIOLIB has
not been set.
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403031332.IGAbZzwq-lkp@intel.com/
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240305142113.795005-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the geneve driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign netdev to gtp->dev at setup time, so, we can get rid of
gtp_dev_init() completely.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the gtp driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the macsec driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240305113728.1974944-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
