Commit graph

1,264,717 commits

Author SHA1 Message Date
Yihong Cao
113f736655 HID: apple: add Jamesdonkey and A3R to non-apple keyboards list
Jamesdonkey A3R keyboard is identified as "Jamesdonkey A3R" in wired
mode, "A3R-U" in wireless mode and "A3R" in bluetooth mode. Adding them
to non-apple keyboards fixes function key.

Signed-off-by: Yihong Cao <caoyihong4@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:31:51 +01:00
Hamish Martin
2682468671 HID: mcp2221: Handle reads greater than 60 bytes
When a user requests more than 60 bytes of data the MCP2221 must chunk
the data in chunks up to 60 bytes long (see command/response code 0x40
in the datasheet).
In order to signal that the device has more data the (undocumented) byte
at byte index 2 of the Get I2C Data response uses the value 0x54. This
contrasts with the case for the final data chunk where the value
returned is 0x55 (MCP2221_I2C_READ_COMPL). The fact that 0x55 was not
returned in the response was interpreted by the driver as a failure
meaning that all reads of more than 60 bytes would fail.

Add support for reads that are split over multiple chunks by looking for
the response code indicating that more data is expected and continuing
the read as the code intended. Some timing delays are required to ensure
the chip has time to refill its FIFO as data is read in from the I2C
bus. This timing has been tested in my system when configured for bus
speeds of 50KHz, 100KHz, and 400KHz and operates well.

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:30:22 +01:00
Hamish Martin
02a4675360 HID: mcp2221: Don't set bus speed on every transfer
Since the initial commit of this driver the I2C bus speed has been
reconfigured for every single transfer. This is despite the fact that we
never change the speed and it is never "lost" by the chip.
Upon investigation we find that what was really happening was that the
setting of the bus speed had the side effect of cancelling a previous
failed command if there was one, thereby freeing the bus. This is the
part that was actually required to keep the bus operational in the face
of failed commands.

Instead of always setting the speed, we now correctly cancel any failed
commands as they are detected. This means we can just set the bus speed
at probe time and remove the previous speed sets on each transfer.
This has the effect of improving performance and reducing the number of
commands required to complete transfers.

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:30:22 +01:00
Hamish Martin
d9786159d2 HID: mcp2221: Set ACPI companion
In scenarios where an I2C device tree is defined in ACPI and exists off
the MCP2221 I2C bus, the devices could not be instantiated.
Mark the USB port that the MCP2221 is connected to as its ACPI companion
so that the USB device can be bound to the ACPI tree when enumerated.
With this change the downstream I2C tree devices can be instantiated on
ACPI systems.

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:30:22 +01:00
Hamish Martin
73ce9f1f27 HID: mcp2221: Allow IO to start during probe
During the probe we add an I2C adapter and as soon as we add that adapter
it may be used for a transfer (e.g via the code in i2cdetect()).
Those transfers are not able to complete and time out. This is because the
HID raw_event callback (mcp2221_raw_event) will not be invoked until the
HID device's 'driver_input_lock' is marked up at the completion of the
probe in hid_device_probe(). This starves the driver of the responses it
is waiting for.
In order to allow the I2C transfers to complete while we are still in the
probe, start the IO once we have completed init of the HID device.

This issue seems to have been seen before and a patch was submitted but
it seems it was never accepted. See:
https://lore.kernel.org/all/20221103222714.21566-3-Enrik.Berkhan@inka.de/

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:29:47 +01:00
Hamish Martin
f2d4a58346 HID: mcp2221: Set driver data before I2C adapter add
The process of adding an I2C adapter can invoke I2C accesses on that new
adapter (see i2c_detect()).

Ensure we have set the adapter's driver data to avoid null pointer
dereferences in the xfer functions during the adapter add.

This has been noted in the past and the same fix proposed but not
completed. See:
https://lore.kernel.org/lkml/ef597e73-ed71-168e-52af-0d19b03734ac@vigem.de/

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:29:47 +01:00
Johannes Roith
740329d712 HID: mcp2200: added driver for GPIOs of MCP2200
Added a gpiochip compatible driver to control the 8 GPIOs of
the MCP2200 by using the HID interface.

Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG,
GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by
default).

The driver was tested while also using the UART of the chip. Setting
and reading the GPIOs has no effect on the UART communication. However,
a reset is triggered after the CONFIGURE command. If the GPIO Direction
is constantly changed, this will affect the communication at low baud
rates. This is a hardware problem of the MCP2200 and is not caused by
the driver.

Signed-off-by: Johannes Roith <johannes@gnu-linux.rocks>
Reviewed-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-11-21 09:27:18 +01:00
Jacek Lawrynowicz
3f7c063492 accel/ivpu/37xx: Fix hangs related to MMIO reset
There is no need to call MMIO reset using VPU_37XX_BUTTRESS_VPU_IP_RESET
register. IP will be reset by FLR or by entering d0i3. Also IP reset
during power_up is not needed as the VPU is already in reset.

Removing MMIO reset improves stability as it a partial device reset
that is not safe in some corner cases.

This change also brings back ivpu_boot_pwr_domain_disable() that
helps to properly power down VPU when it is hung by a buggy workload.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Fixes: 828d63042a ("accel/ivpu: Don't enter d0i3 during FLR")
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231115111004.1304092-1-jacek.lawrynowicz@linux.intel.com
2023-11-21 09:20:25 +01:00
Uwe Kleine-König
16b01df3c5 drm/sprd: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert the sprd drm drivers from always returning zero in the
remove callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-33-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:53 +01:00
Uwe Kleine-König
0fa2db3bc7 drm/nouveau: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-32-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:53 +01:00
Uwe Kleine-König
ac96555768 drm/meson: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-31-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:53 +01:00
Uwe Kleine-König
30b749adb1 drm/mediatek: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-30-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:53 +01:00
Uwe Kleine-König
8c67c9a4e4 drm/kmb: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-29-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:52 +01:00
Uwe Kleine-König
a7e43c0a1a drm/imx: lcdc: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-28-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:52 +01:00
Uwe Kleine-König
60096f0a77 drm/imx/dcss: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-27-u.kleine-koenig@pengutronix.de
2023-11-21 09:18:52 +01:00
Uwe Kleine-König
d437dab5b0 drm/etnaviv: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert the etnaviv drm driver from always returning zero in
the remove callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-25-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:54 +01:00
Uwe Kleine-König
3cdbe59868 drm/bridge: tpd12s015: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-24-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:53 +01:00
Uwe Kleine-König
3438cf177a drm/bridge: cdns-mhdp8546: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-23-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:52 +01:00
Uwe Kleine-König
be79252e7c drm/bridge: cdns-mhdp8546: Improve error reporting in remove callback
Replace the generic error message issued by the driver core when the remove
callback returns non-zero ("remove callback returned a non-zero value. This
will be ignored.") by a message that tells the actual problem.

Also simplify a bit by checking the return value of wait_event_timeout a
bit later.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-22-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:51 +01:00
Uwe Kleine-König
b47914741a drm/armada: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert the armada drm drivers from always returning zero in
the remove callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-21-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:50 +01:00
Uwe Kleine-König
da20c383de drm/arcpgu: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-20-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:49 +01:00
Uwe Kleine-König
ce3e112e7a drm/bridge: tpd12s015: Drop buggy __exit annotation for remove function
With tpd12s015_remove() marked with __exit this function is discarded
when the driver is compiled as a built-in. The result is that when the
driver unbinds there is no cleanup done which results in resource
leakage or worse.

Fixes: cff5e6f7e8 ("drm/bridge: Add driver for the TI TPD12S015 HDMI level shifter")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-19-u.kleine-koenig@pengutronix.de
2023-11-21 09:17:48 +01:00
Andy Shevchenko
a6584711e6
platform/x86: intel_telemetry: Fix kernel doc descriptions
LKP found issues with a kernel doc in the driver:

core.c:116: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_update_events'
core.c:188: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_get_eventconfig'

It looks like it were copy'n'paste typos when these descriptions
had been introduced. Fix the typos.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310070743.WALmRGSY-lkp@intel.com/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231120150756.1661425-1-andriy.shevchenko@linux.intel.com
Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2023-11-21 10:09:04 +02:00
Hans de Goede
8d9ce3e53b
MAINTAINERS: Drop Mark Gross as maintainer for x86 platform drivers
Mark has not really been active as maintainer for x86 platform drivers
lately, drop Mark from the MAINTAINERS entries for drivers/platform/x86,
drivers/platform/mellanox and drivers/platform/surface.

Cc: Mark Gross <markgross@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231120154548.611041-1-hdegoede@redhat.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2023-11-21 10:02:27 +02:00
Greg Kroah-Hartman
849d3f985e thunderbolt: Fixes for v6.7-rc3
This includes following USB4/Thunderbolt fixes for v6.7-rc3:
 
   - Fix a lane bonding issue on ASMedia USB4 device
   - Send uevents when link is switched to asymmetric or symmetric
   - Only add device router DP IN adapters to the head of resource list
     to avoid issues during system resume.
 
 All these have been in linux-next with no reported issues.
 -----BEGIN PGP SIGNATURE-----
 
 iQJUBAABCgA+FiEEVTdhRGBbNzLrSUBaAP2fSd+ZWKAFAmVcRjogHG1pa2Eud2Vz
 dGVyYmVyZ0BsaW51eC5pbnRlbC5jb20ACgkQAP2fSd+ZWKBPnw//Yhw7Oi7cZesm
 xJGm26tWtWH81G54ZHjR8NlFdsSHHR0J3vVujfRFgA9PR/z4rSfEmEdwL3NANnH+
 TWGP2IOgCM3sMkDXuLmTkoxbnhZPkP2eMfGtegRd565mQeEQmIgGbDkMO68ZwOGw
 6a5m1jAVI7fV8M81XtiSykwPSqd+flbnBC3ic+glimfvfqc6W74CwD9GW5B2NhRF
 0NSAfPvnpZqoAihssCq9K9OyWsceP0VN3f6AZdscIL0bhJzmvedf7TaTD3p/6lKT
 XO/gFZcVTJX46mgCR96B7Phs6/n67QXmdmKzatfdsUxTxWwqggQEXXgz/H0XPV7S
 Q3OjCkO7BJej1sjgHz74nderoDLGEiEvDXpBSs6dLBFzu7TBV9c8mn9WOirAZSEn
 ApEqO2x1DgYmT6SJoQ3yzho7RvrUSEixHShCitp7yzBo4AzUlO7kyY40YsnukRso
 tyS/ocduJGxrXH/4Xb9+DbW4yIf+/6A89tortPUbFwvFabWttpr3XdgXxFvNIU9h
 RcHBC7iDoEzr/nc2ubkhAURAWflx8qQn7539US2RWAMsIU7D5UAg2mg/TK7wyolT
 7teCfMjIb8nPWlFIRtAgkmifiJDfENl8pg9PzUNYgY4CArfAJpLvfINwxRNa6lBg
 5Mmjd8P8BcohAT3YWlrZIoyoC2hzxbg=
 =vOti
 -----END PGP SIGNATURE-----

Merge tag 'thunderbolt-for-v6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus

Mika writes:

thunderbolt: Fixes for v6.7-rc3

This includes following USB4/Thunderbolt fixes for v6.7-rc3:

  - Fix a lane bonding issue on ASMedia USB4 device
  - Send uevents when link is switched to asymmetric or symmetric
  - Only add device router DP IN adapters to the head of resource list
    to avoid issues during system resume.

All these have been in linux-next with no reported issues.

* tag 'thunderbolt-for-v6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (1451 commits)
  thunderbolt: Only add device router DP IN to the head of the DP resource list
  thunderbolt: Send uevent after asymmetric/symmetric switch
  thunderbolt: Set lane bonding bit only for downstream port
2023-11-21 08:13:55 +01:00
Yanteng Si
c517fd2738 Docs/zh_CN/LoongArch: Update links in LoongArch introduction.rst
LoongArch-Vol1 has been updated to v1.10, the links in the documentation
are out of date, let's update it.

Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:26 +08:00
Yanteng Si
10301780c9 Docs/LoongArch: Update links in LoongArch introduction.rst
LoongArch-Vol1 has been updated to v1.10, the links in the documentation
are out of date, let's update it.

Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Bibo Mao
d43f37b734 LoongArch: Implement constant timer shutdown interface
When a cpu is hot-unplugged, it is put in idle state and the function
arch_cpu_idle_dead() is called. The timer interrupt for this processor
should be disabled, otherwise there will be pending timer interrupt for
the unplugged cpu, so that vcpu is prevented from giving up scheduling
when system is running in vm mode.

This patch implements the timer shutdown interface so that the constant
timer will be properly disabled when a CPU is hot-unplugged.

Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Huacai Chen
19d86a4962 LoongArch: Mark {dmw,tlb}_virt_to_page() exports as non-GPL
Mark {dmw,tlb}_virt_to_page() exports as non-GPL, in order to let
out-of-tree modules (e.g. OpenZFS) be built without errors. Otherwise
we get:

ERROR: modpost: GPL-incompatible module zfs.ko uses GPL-only symbol 'dmw_virt_to_page'
ERROR: modpost: GPL-incompatible module zfs.ko uses GPL-only symbol 'tlb_virt_to_page'

Reported-by: Haowu Ge <gehaowu@bitmoe.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Huacai Chen
902d75cdf0 LoongArch: Silence the boot warning about 'nokaslr'
The kernel parameter 'nokaslr' is handled before start_kernel(), so we
don't need early_param() to mark it technically. But it can cause a boot
warning as follows:

Unknown kernel command line parameters "nokaslr", will be passed to user space.

When we use 'init=/bin/bash', 'nokaslr' which passed to user space will
even cause a kernel panic. So we use early_param() to mark 'nokaslr',
simply print a notice and silence the boot warning (also fix a potential
panic). This logic is similar to RISC-V.

Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Huacai Chen
ee2daf7102 LoongArch: Add __percpu annotation for __percpu_read()/__percpu_write()
When build kernel with C=1, we get:

arch/loongarch/kernel/process.c:234:46: warning: incorrect type in argument 1 (different address spaces)
arch/loongarch/kernel/process.c:234:46:    expected void *ptr
arch/loongarch/kernel/process.c:234:46:    got unsigned long [noderef] __percpu *
arch/loongarch/kernel/process.c:234:46: warning: incorrect type in argument 1 (different address spaces)
arch/loongarch/kernel/process.c:234:46:    expected void *ptr
arch/loongarch/kernel/process.c:234:46:    got unsigned long [noderef] __percpu *
arch/loongarch/kernel/process.c:234:46: warning: incorrect type in argument 1 (different address spaces)
arch/loongarch/kernel/process.c:234:46:    expected void *ptr
arch/loongarch/kernel/process.c:234:46:    got unsigned long [noderef] __percpu *
arch/loongarch/kernel/process.c:234:46: warning: incorrect type in argument 1 (different address spaces)
arch/loongarch/kernel/process.c:234:46:    expected void *ptr
arch/loongarch/kernel/process.c:234:46:    got unsigned long [noderef] __percpu *

Add __percpu annotation for __percpu_read()/__percpu_write() can avoid
such warnings. __percpu_xchg() and other functions don't need annotation
because their wrapper, i.e. _pcp_protect(), already suppresses warnings.

Also adjust the indentations in this file.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311080409.LlOfTR3m-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311080840.Vc2kXhfp-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311081340.3k72KKdg-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311120926.cjYHyoYw-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311152142.g6UyNx1R-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311160339.DbhaH8LX-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311181454.CTPrSYmQ-lkp@intel.com/
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
WANG Rui
aa0cbc1b50 LoongArch: Record pc instead of offset in la_abs relocation
To clarify, the previous version functioned flawlessly. However, it's
worth noting that the LLVM's LoongArch backend currently lacks support
for cross-section label calculations. With this patch, we enable the use
of clang to compile relocatable kernels.

Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
WANG Rui
cbfd44bd5c LoongArch: Explicitly set -fdirect-access-external-data for vmlinux
After this llvm commit [1], The -fno-pic does not imply direct access
external data. Explicitly set -fdirect-access-external-data for vmlinux
that can avoids GOT entries.

Link: 47eeee2977
Suggested-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Masahiro Yamada
d3ec75bc63 LoongArch: Add dependency between vmlinuz.efi and vmlinux.efi
A common issue in Makefile is a race in parallel building.

You need to be careful to prevent multiple threads from writing to the
same file simultaneously.

Commit 3939f33450 ("ARM: 8418/1: add boot image dependencies to not
generate invalid images") addressed such a bad scenario.

A similar symptom occurs with the following command:

  $ make -j$(nproc) ARCH=loongarch vmlinux.efi vmlinuz.efi
    [ snip ]
    SORTTAB vmlinux
    OBJCOPY arch/loongarch/boot/vmlinux.efi
    OBJCOPY arch/loongarch/boot/vmlinux.efi
    PAD     arch/loongarch/boot/vmlinux.bin
    GZIP    arch/loongarch/boot/vmlinuz
    OBJCOPY arch/loongarch/boot/vmlinuz.o
    LD      arch/loongarch/boot/vmlinuz.efi.elf
    OBJCOPY arch/loongarch/boot/vmlinuz.efi

The log "OBJCOPY arch/loongarch/boot/vmlinux.efi" is displayed twice.

It indicates that two threads simultaneously enter arch/loongarch/boot/
and write to arch/loongarch/boot/vmlinux.efi.

It occasionally leads to a build failure:

  $ make -j$(nproc) ARCH=loongarch vmlinux.efi vmlinuz.efi
    [ snip ]
    SORTTAB vmlinux
    OBJCOPY arch/loongarch/boot/vmlinux.efi
    PAD     arch/loongarch/boot/vmlinux.bin
  truncate: Invalid number: ‘arch/loongarch/boot/vmlinux.bin’
  make[2]: *** [drivers/firmware/efi/libstub/Makefile.zboot:13:
  arch/loongarch/boot/vmlinux.bin] Error 1
  make[2]: *** Deleting file 'arch/loongarch/boot/vmlinux.bin'
  make[1]: *** [arch/loongarch/Makefile:146: vmlinuz.efi] Error 2
  make[1]: *** Waiting for unfinished jobs....
  make: *** [Makefile:234: __sub-make] Error 2

vmlinuz.efi depends on vmlinux.efi, but such a dependency is not
specified in arch/loongarch/Makefile.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
2023-11-21 15:03:25 +08:00
Alexei Starovoitov
acb12c859a Merge branch 'verify-callbacks-as-if-they-are-called-unknown-number-of-times'
Eduard Zingerman says:

====================
verify callbacks as if they are called unknown number of times

This series updates verifier logic for callback functions handling.
Current master simulates callback body execution exactly once,
which leads to verifier not detecting unsafe programs like below:

    static int unsafe_on_zero_iter_cb(__u32 idx, struct num_context *ctx)
    {
        ctx->i = 0;
        return 0;
    }

    SEC("?raw_tp")
    int unsafe_on_zero_iter(void *unused)
    {
        struct num_context loop_ctx = { .i = 32 };
        __u8 choice_arr[2] = { 0, 1 };

        bpf_loop(100, unsafe_on_zero_iter_cb, &loop_ctx, 0);
        return choice_arr[loop_ctx.i];
    }

This was reported previously in [0].
The basic idea of the fix is to schedule callback entry state for
verification in env->head until some identical, previously visited
state in current DFS state traversal is found. Same logic as with open
coded iterators, and builds on top recent fixes [1] for those.

The series is structured as follows:
- patches #1,2,3 update strobemeta, xdp_synproxy selftests and
  bpf_loop_bench benchmark to allow convergence of the bpf_loop
  callback states;
- patches #4,5 just shuffle the code a bit;
- patch #6 is the main part of the series;
- patch #7 adds test cases for #6;
- patch #8 extend patch #6 with same speculative scalar widening
  logic, as used for open coded iterators;
- patch #9 adds test cases for #8;
- patch #10 extends patch #6 to track maximal number of callback
  executions specifically for bpf_loop();
- patch #11 adds test cases for #10.

Veristat results comparing this series to master+patches #1,2,3 using selftests
show the following difference:

File                       Program        States (A)  States (B)  States (DIFF)
-------------------------  -------------  ----------  ----------  -------------
bpf_loop_bench.bpf.o       benchmark               1           2  +1 (+100.00%)
pyperf600_bpf_loop.bpf.o   on_event              322         407  +85 (+26.40%)
strobemeta_bpf_loop.bpf.o  on_event              113         151  +38 (+33.63%)
xdp_synproxy_kern.bpf.o    syncookie_tc          341         291  -50 (-14.66%)
xdp_synproxy_kern.bpf.o    syncookie_xdp         344         301  -43 (-12.50%)

Veristat results comparing this series to master using Tetragon BPF
files [2] also show some differences.
States diff varies from +2% to +15% on 23 programs out of 186,
no new failures.

Changelog:
- V3 [5] -> V4, changes suggested by Andrii:
  - validate mark_chain_precision() result in patch #10;
  - renaming s/cumulative_callback_depth/callback_unroll_depth/.
- V2 [4] -> V3:
  - fixes in expected log messages for test cases:
    - callback_result_precise;
    - parent_callee_saved_reg_precise_with_callback;
    - parent_stack_slot_precise_with_callback;
  - renamings (suggested by Alexei):
    - s/callback_iter_depth/cumulative_callback_depth/
    - s/is_callback_iter_next/calls_callback/
    - s/mark_callback_iter_next/mark_calls_callback/
  - prepare_func_exit() updated to exit with -EFAULT when
    callee->in_callback_fn is true but calls_callback() is not true
    for callsite;
  - test case 'bpf_loop_iter_limit_nested' rewritten to use return
    value check instead of verifier log message checks
    (suggested by Alexei).
- V1 [3] -> V2, changes suggested by Andrii:
  - small changes for error handling code in __check_func_call();
  - callback body processing log is now matched in relevant
    verifier_subprog_precision.c tests;
  - R1 passed to bpf_loop() is now always marked as precise;
  - log level 2 message for bpf_loop() iteration termination instead of
    iteration depth messages;
  - __no_msg macro removed;
  - bpf_loop_iter_limit_nested updated to avoid using __no_msg;
  - commit message for patch #3 updated according to Alexei's request.

[0] https://lore.kernel.org/bpf/CA+vRuzPChFNXmouzGG+wsy=6eMcfr1mFG0F3g7rbg-sedGKW3w@mail.gmail.com/
[1] https://lore.kernel.org/bpf/20231024000917.12153-1-eddyz87@gmail.com/
[2] git@github.com:cilium/tetragon.git
[3] https://lore.kernel.org/bpf/20231116021803.9982-1-eddyz87@gmail.com/T/#t
[4] https://lore.kernel.org/bpf/20231118013355.7943-1-eddyz87@gmail.com/T/#t
[5] https://lore.kernel.org/bpf/20231120225945.11741-1-eddyz87@gmail.com/T/#t
====================

Link: https://lore.kernel.org/r/20231121020701.26440-1-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:41 -08:00
Eduard Zingerman
57e2a52dee selftests/bpf: check if max number of bpf_loop iterations is tracked
Check that even if bpf_loop() callback simulation does not converge to
a specific state, verification could proceed via "brute force"
simulation of maximal number of callback calls.

Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-12-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:40 -08:00
Eduard Zingerman
bb124da69c bpf: keep track of max number of bpf_loop callback iterations
In some cases verifier can't infer convergence of the bpf_loop()
iteration. E.g. for the following program:

    static int cb(__u32 idx, struct num_context* ctx)
    {
        ctx->i++;
        return 0;
    }

    SEC("?raw_tp")
    int prog(void *_)
    {
        struct num_context ctx = { .i = 0 };
        __u8 choice_arr[2] = { 0, 1 };

        bpf_loop(2, cb, &ctx, 0);
        return choice_arr[ctx.i];
    }

Each 'cb' simulation would eventually return to 'prog' and reach
'return choice_arr[ctx.i]' statement. At which point ctx.i would be
marked precise, thus forcing verifier to track multitude of separate
states with {.i=0}, {.i=1}, ... at bpf_loop() callback entry.

This commit allows "brute force" handling for such cases by limiting
number of callback body simulations using 'umax' value of the first
bpf_loop() parameter.

For this, extend bpf_func_state with 'callback_depth' field.
Increment this field when callback visiting state is pushed to states
traversal stack. For frame #N it's 'callback_depth' field counts how
many times callback with frame depth N+1 had been executed.
Use bpf_func_state specifically to allow independent tracking of
callback depths when multiple nested bpf_loop() calls are present.

Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-11-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:40 -08:00
Eduard Zingerman
9f3330aa64 selftests/bpf: test widening for iterating callbacks
A test case to verify that imprecise scalars widening is applied to
callback entering state, when callback call is simulated repeatedly.

Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-10-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:40 -08:00
Eduard Zingerman
cafe2c2150 bpf: widening for callback iterators
Callbacks are similar to open coded iterators, so add imprecise
widening logic for callback body processing. This makes callback based
loops behave identically to open coded iterators, e.g. allowing to
verify programs like below:

  struct ctx { u32 i; };
  int cb(u32 idx, struct ctx* ctx)
  {
          ++ctx->i;
          return 0;
  }
  ...
  struct ctx ctx = { .i = 0 };
  bpf_loop(100, cb, &ctx, 0);
  ...

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-9-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:40 -08:00
Eduard Zingerman
958465e217 selftests/bpf: tests for iterating callbacks
A set of test cases to check behavior of callback handling logic,
check if verifier catches the following situations:
- program not safe on second callback iteration;
- program not safe on zero callback iterations;
- infinite loop inside a callback.

Verify that callback logic works for bpf_loop, bpf_for_each_map_elem,
bpf_user_ringbuf_drain, bpf_find_vma.

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-8-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:36:40 -08:00
Eduard Zingerman
ab5cfac139 bpf: verify callbacks as if they are called unknown number of times
Prior to this patch callbacks were handled as regular function calls,
execution of callback body was modeled exactly once.
This patch updates callbacks handling logic as follows:
- introduces a function push_callback_call() that schedules callback
  body verification in env->head stack;
- updates prepare_func_exit() to reschedule callback body verification
  upon BPF_EXIT;
- as calls to bpf_*_iter_next(), calls to callback invoking functions
  are marked as checkpoints;
- is_state_visited() is updated to stop callback based iteration when
  some identical parent state is found.

Paths with callback function invoked zero times are now verified first,
which leads to necessity to modify some selftests:
- the following negative tests required adding release/unlock/drop
  calls to avoid previously masked unrelated error reports:
  - cb_refs.c:underflow_prog
  - exceptions_fail.c:reject_rbtree_add_throw
  - exceptions_fail.c:reject_with_cp_reference
- the following precision tracking selftests needed change in expected
  log trace:
  - verifier_subprog_precision.c:callback_result_precise
    (note: r0 precision is no longer propagated inside callback and
           I think this is a correct behavior)
  - verifier_subprog_precision.c:parent_callee_saved_reg_precise_with_callback
  - verifier_subprog_precision.c:parent_stack_slot_precise_with_callback

Reported-by: Andrew Werner <awerner32@gmail.com>
Closes: https://lore.kernel.org/bpf/CA+vRuzPChFNXmouzGG+wsy=6eMcfr1mFG0F3g7rbg-sedGKW3w@mail.gmail.com/
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-7-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:35:44 -08:00
Rob Clark
6c15808d9b drm/msm/gem: Demote allocations to __GFP_NOWARN
For allocations with userspace controlled size, we should not warn on
allocation failure.  Fixes KASAN splat:

   WARNING: CPU: 6 PID: 29557 at mm/page_alloc.c:5398 __alloc_pages+0x160c/0x2204
   Modules linked in: bridge stp llc hci_vhci tun veth xt_cgroup uinput xt_MASQUERADE rfcomm ip6table_nat fuse 8021q r8153_ecm cdc_ether usbnet r8152 mii venus_enc venus_dec uvcvideo algif_hash algif_skcipher af_alg qcom_spmi_adc_tm5 qcom_spmi_adc5 qcom_vadc_common qcom_spmi_temp_alarm cros_ec_typec typec hci_uart btqca qcom_stats snd_soc_sc7180 venus_core ath10k_snoc ath10k_core ath coresight_tmc coresight_replicator coresight_etm4x coresight_funnel snd_soc_lpass_sc7180 mac80211 coresight bluetooth ecdh_generic ecc cfg80211 cros_ec_sensorhub lzo_rle lzo_compress zram joydev
   CPU: 6 PID: 29557 Comm: syz-executor Not tainted 5.15.110-lockdep-19320-g89d010b0a9df #1 45bdd400697a78353f2927c116615abba810e5dd
   Hardware name: Google Kingoftown (DT)
   pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
   pc : __alloc_pages+0x160c/0x2204
   lr : __alloc_pages+0x58/0x2204
   sp : ffffffc0214176c0
   x29: ffffffc0214178a0 x28: ffffff801f7b4000 x27: 0000000000000000
   x26: ffffff808a4fa000 x25: 1ffffff011290781 x24: ffffff808a59c000
   x23: 0000000000000010 x22: ffffffc0080e6980 x21: 0000000000000010
   x20: 0000000000000000 x19: 00000000080001f8 x18: 0000000000000000
   x17: 0000000000000000 x16: 0000000000000000 x15: 0000000020000500
   x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000001
   x11: 0000000000000000 x10: 1ffffff804282f06 x9 : 0000000000000000
   x8 : ffffffc021417848 x7 : 0000000000000000 x6 : ffffffc0082ac788
   x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000010
   x2 : 0000000000000008 x1 : 0000000000000000 x0 : ffffffc021417830
   Call trace:
   __alloc_pages+0x160c/0x2204
   kmalloc_order+0x50/0xf4
   kmalloc_order_trace+0x38/0x18c
   __kmalloc+0x300/0x45c
   msm_ioctl_gem_submit+0x284/0x5988
   drm_ioctl_kernel+0x270/0x418
   drm_ioctl+0x5e0/0xbf8
   __arm64_sys_ioctl+0x154/0x1d0
   invoke_syscall+0x98/0x278
   el0_svc_common+0x214/0x274
   do_el0_svc+0x9c/0x19c
   el0_svc+0x5c/0xc0
   el0t_64_sync_handler+0x78/0x108
   el0t_64_sync+0x1a4/0x1a8

Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/564191/
2023-11-20 18:35:26 -08:00
Rob Clark
b2acb89af1 drm/msm/gem: Demote userspace errors to DRM_UT_DRIVER
Error messages resulting from incorrect usage of the kernel uabi should
not spam dmesg by default.  But it is useful to enable them to debug
userspace.  So demote to DRM_UT_DRIVER.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/564189/
2023-11-20 18:35:26 -08:00
Eduard Zingerman
58124a98cb bpf: extract setup_func_entry() utility function
Move code for simulated stack frame creation to a separate utility
function. This function would be used in the follow-up change for
callbacks handling.

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-6-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:33:35 -08:00
Eduard Zingerman
683b96f960 bpf: extract __check_reg_arg() utility function
Split check_reg_arg() into two utility functions:
- check_reg_arg() operating on registers from current verifier state;
- __check_reg_arg() operating on a specific set of registers passed as
  a parameter;

The __check_reg_arg() function would be used by a follow-up change for
callbacks handling.

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-5-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:33:35 -08:00
Eduard Zingerman
f40bfd1679 selftests/bpf: fix bpf_loop_bench for new callback verification scheme
This is a preparatory change. A follow-up patch "bpf: verify callbacks
as if they are called unknown number of times" changes logic for
callbacks handling. While previously callbacks were verified as a
single function call, new scheme takes into account that callbacks
could be executed unknown number of times.

This has dire implications for bpf_loop_bench:

    SEC("fentry/" SYS_PREFIX "sys_getpgid")
    int benchmark(void *ctx)
    {
            for (int i = 0; i < 1000; i++) {
                    bpf_loop(nr_loops, empty_callback, NULL, 0);
                    __sync_add_and_fetch(&hits, nr_loops);
            }
            return 0;
    }

W/o callbacks change verifier sees it as a 1000 calls to
empty_callback(). However, with callbacks change things become
exponential:
- i=0: state exploring empty_callback is scheduled with i=0 (a);
- i=1: state exploring empty_callback is scheduled with i=1;
  ...
- i=999: state exploring empty_callback is scheduled with i=999;
- state (a) is popped from stack;
- i=1: state exploring empty_callback is scheduled with i=1;
  ...

Avoid this issue by rewriting outer loop as bpf_loop().
Unfortunately, this adds a function call to a loop at runtime, which
negatively affects performance:

            throughput               latency
   before:  149.919 ± 0.168 M ops/s, 6.670 ns/op
   after :  137.040 ± 0.187 M ops/s, 7.297 ns/op

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-4-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:33:35 -08:00
Eduard Zingerman
87eb0152bc selftests/bpf: track string payload offset as scalar in strobemeta
This change prepares strobemeta for update in callbacks verification
logic. To allow bpf_loop() verification converge when multiple
callback iterations are considered:
- track offset inside strobemeta_payload->payload directly as scalar
  value;
- at each iteration make sure that remaining
  strobemeta_payload->payload capacity is sufficient for execution of
  read_{map,str}_var functions;
- make sure that offset is tracked as unbound scalar between
  iterations, otherwise verifier won't be able infer that bpf_loop
  callback reaches identical states.

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-3-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:33:35 -08:00
Eduard Zingerman
977bc146d4 selftests/bpf: track tcp payload offset as scalar in xdp_synproxy
This change prepares syncookie_{tc,xdp} for update in callbakcs
verification logic. To allow bpf_loop() verification converge when
multiple callback itreations are considered:
- track offset inside TCP payload explicitly, not as a part of the
  pointer;
- make sure that offset does not exceed MAX_PACKET_OFF enforced by
  verifier;
- make sure that offset is tracked as unbound scalar between
  iterations, otherwise verifier won't be able infer that bpf_loop
  callback reaches identical states.

Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-11-20 18:33:35 -08:00
Rob Clark
9902cb999e drm/msm/gem: Add metadata
The EXT_external_objects extension is a bit awkward as it doesn't pass
explicit modifiers, leaving the importer to guess with incomplete
information.  In the case of vk (turnip) exporting and gl (freedreno)
importing, the "OPTIMAL_TILING_EXT" layout depends on VkImageCreateInfo
flags (among other things), which the importer does not know.  Which
unfortunately leaves us with the need for a metadata back-channel.

The contents of the metadata are defined by userspace.  The
EXT_external_objects extension is only required to work between
compatible versions of gl and vk drivers, as defined by device and
driver UUIDs.

v2: add missing metadata kfree
v3: Rework to move copy_from/to_user out from under gem obj lock
    to avoid angering lockdep about deadlocks against fs-reclaim

Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/566157/
2023-11-20 18:33:17 -08:00
Rob Clark
d1912f6972 drm/msm: Small uabi fixes
Correct the minor version exposed and error return value for
MSM_INFO_GET_NAME.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/566155/
2023-11-20 18:33:17 -08:00