This integrates the PHY wrapper into the core hcd infrastructure.
Multiple PHYs which are part of the HCD's device tree node are now
managed (= powered on/off when needed), by the new usb_phy_roothub code.
Suspend and resume is also supported, however not for
runtime/auto-suspend (which is triggered for example when no devices are
connected to the USB bus). This is needed on some SoCs (for example
Amlogic Meson GXL) because if the PHYs are disabled during auto-suspend
then devices which are plugged in afterwards are not seen by the host.
One example where this is required is the Amlogic GXL and GXM SoCs:
They are using a dwc3 USB controller with up to three ports enabled on
the internal roothub. Each port has it's own PHY which must be enabled
(if one of the PHYs is left disabled then none of the USB ports works at
all).
The new logic works on the Amlogic GXL and GXM SoCs because the dwc3
driver internally creates a xhci-hcd which then registers a HCD which
then triggers our new PHY wrapper.
USB controller drivers can opt out of this by setting
"skip_phy_initialization" in struct usb_hcd to true. This is identical
to how it works for a single USB PHY, so the "multiple PHY" handling is
disabled for drivers that opted out of the management logic of a single
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.
Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}
With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB HCD core driver parses the device-tree node for "phys" and
"usb-phys" properties. It also manages the power state of these PHYs
automatically.
However, drivers may opt-out of this behavior by setting "phy" or
"usb_phy" in struct usb_hcd to a non-null value. An example where this
is required is the "Qualcomm USB2 controller", implemented by the
chipidea driver. The hardware requires that the PHY is only powered on
after the "reset completed" event from the controller is received.
A follow-up patch will allow the USB HCD core driver to manage more than
one PHY. Add a new "skip_phy_initialization" bitflag to struct usb_hcd
so drivers can opt-out of any PHY management provided by the USB HCD
core driver.
This also updates the existing drivers so they use the new flag if they
want to opt out of the PHY management provided by the USB HCD core
driver. This means that for these drivers the new "multiple PHY"
handling (which will be added in a follow-up patch) will be disabled as
well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB HCD may have several PHYs which need to be configured before the
the HCD starts working.
This adds the documentation for such a USB HCD as well as a reference to
the new "usb-hcd.txt" from all bindings that implement a USB HCD which
support one USB PHY per port.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I think we need to soften the language a bit. It might scare folks
off, especially the:
We prefer to fully disclose the bug as soon as possible.
which is not really the case. Linus says:
It's not full disclosure, it's not coordinated disclosure,
and it's not "no disclosure". It's more like just "timely
open fixes".
I changed a bit of the wording in here, but mostly to remove the word
"disclosure" since it seems to mean very specific things to people
that we do not mean here.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There is a need to use DA7219 as DAI clock master for other codecs
within a system, which means that the DAI clocks are required to
remain, regardless of whether the codec is actually running
playback/capture. To be able to expose control of the DAI clocking
the common clock framework has been employed.
The current implementation adds a simple clock gate for enabling
and disabling the DAI clocks, with no rate control supported
(this is still handled through standard hw_params() functions as
before). If DT is enabled then the clock is added to the OF
providers list, otherwise a clkdev lookup is used.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use kasprintf instead of combination of kmalloc and sprintf and
therefore avoid unnecessary computation of string length.
Also, remove the useless local variable.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix some iomap locking problems
- Don't allocate cow blocks when we're zeroing file data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=T9nM
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.16-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix some iomap locking problems
- Don't allocate cow blocks when we're zeroing file data
* tag 'xfs-4.16-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't block on the ilock for RWF_NOWAIT
xfs: don't start out with the exclusive ilock for direct I/O
xfs: don't allocate COW blocks for zeroing holes or unwritten extents
ACPI spec inserts sections for new features frequently and section
numbers are changed. It is easy to refer to ACPI spec if ACPI version
is available in comments.
There are no functional changes.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabing Latency Tolerance Messaging before port reset is unnecessary.
LTM is automatically disabled at port reset.
If host can't communicate with the device the LTM message will fail, and
the hub driver will unnecessarily do a logical disconnect.
Broken communication is ofter the reason for a reset in the first place.
Additionally we can't guarantee device is in a configured state,
epecially in reset-resume case when root hub lost power.
LTM can't be modified unless device is in a configured state.
Just remove LTM disabling before port reset.
Details about LTM and port reset in USB 3 specification:
USB 3 spec section 9.4.5
"The LTM Enable field can be modified by the SetFeature() and
ClearFeature() requests using the LTM_ENABLE feature selector.
This field is reset to zero when the device is reset."
USB 3 spec section 9.4.1
"The device shall process a Clear Feature (U1_Enable or U2_Enable or
LTM_Enable) only if the device is in the configured state."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add waiting for an URB transmit finish that let the last URB to be sent
(to be not discarded) during 'release' procedure. W/o this waiting,the
last frame will be nearly always lost.
A test case: an attempt of sending a single frame:
echo -en "\001mk255" >/dev/adutux0
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the DELL_SMBIOS_SMM backend is enabled, the DELL_SMBIOS symbol
depends on DELL_DCDBAS, and we must avoid the situation where
DELL_SMBIOS=y and DCDBAS=m.
Adding the conditional dependency to DELL_SMBIOS such as:
depends !DELL_SMBIOS_SMM || (DCDBAS || DCDBAS=n)
results in the Kconfig tooling complaining about a circular dependency,
although it appears to work in practice.
Avoid the errors by simplifying the dependency and forcing DELL_SMBIOS
to be <= DCDBAS if DCDBAS is enabled (thanks to Greg KH for the
suggestion).
Cc: Mario.Limonciello@dell.com
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Avoid accidental configurations by setting default y for DELL_SMBIOS
backends. Avoid this impacting the default build size, by making them
dependent on DELL_SMBIOS, so they only appear when DELL_SMBIOS is
manually selected, or by DELL_LAPTOP or DELL_WMI.
While DELL_SMBIOS does have a prompt, it does not have any dependencies.
Keeping DELL_SMBIOS visible, despite being "select"ed by DELL_LAPTOP and
DELL_WMI, is a deliberate choice to provide context for the WMI and SMM
backends, which would otherwise appear to float without context within
the menu.
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some race conditions were raised due to dell-smbios and its backends
not being ready by the time that a consumer would call one of the
exported methods.
To avoid this problem, guarantee that all initialization has been
done by linking them all together and running init for them all.
As part of this change the Kconfig needs to be adjusted so that
CONFIG_DELL_SMBIOS_SMM and CONFIG_DELL_SMBIOS_WMI are boolean
rather than modules.
CONFIG_DELL_SMBIOS is a visually selectable option again and both
CONFIG_DELL_SMBIOS_WMI and CONFIG_DELL_SMBIOS_SMM are optional.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: Update prompt and help text for DELL_SMBIOS_* backends]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This is being done to faciliate a later change to link all the dell-smbios
drivers together.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
WARNING: function definition argument 'struct calling_interface_buffer *'
should also have an identifier name
+ int (*call_fn)(struct calling_interface_buffer *);
WARNING: Block comments use * on subsequent lines
+ /* 4 bytes of table header, plus 7 bytes of Dell header,
plus at least
+ 6 bytes of entry */
WARNING: Block comments use a trailing */ on a separate line
+ 6 bytes of entry */
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
One notable fix to properly advertise our support for a new firmware feature,
caused by two series conflicting semantically but not textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but needed to
complete the userspace API and good to have before the driver is in a released
kernel.
Finally three minor selftest fixes, and a fix for intermittent build failures
for some obscure platforms, caused by a missing make dependency.
Thanks to:
Alastair D'Silva, Bharata B Rao, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=ajRr
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix to properly advertise our support for a new firmware
feature, caused by two series conflicting semantically but not
textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but
needed to complete the userspace API and good to have before the
driver is in a released kernel.
Finally three minor selftest fixes, and a fix for intermittent build
failures for some obscure platforms, caused by a missing make
dependency.
Thanks to: Alastair D'Silva, Bharata B Rao, Guenter Roeck"
* tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Fix vector5 in ibm architecture vector table
ocxl: Document the OCXL_IOCTL_GET_METADATA IOCTL
ocxl: Add get_metadata IOCTL to share OCXL information to userspace
selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable
selftests/powerpc: Fix missing clean of pmu/lib.o
powerpc/boot: Fix random libfdt related build errors
selftests/powerpc: Skip tm-trap if transactional memory is not enabled
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a header providing definitions for handling
Status messages. Currently the header only focuses on handling
incoming Status messages.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a header providing definitions for handling Alert
messages. Currently the header only focuses on handling incoming
alerts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds definitions for PD Rev 3.0 messages, including
APDO PPS and extended message support for TCPM.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To help folks like me that use scripts/get_maintainer.pl.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Changed usbip_network, usbip_attach, usbip_list, and usbipd to use
and propagate the new error codes in server reply messages.
usbip_net_recv_op_common() is changed to take a pointer to status
return the status returned in the op_common.status to callers.
usbip_attach and usbip_list use the common interface to print error
messages to indicate why the request failed.
With this change the messages say why a request failed:
- when a client requests a device that is already exported:
usbip attach -r server_name -b 3-10.2
usbip: error: Attach Request for 3-10.2 failed - Device busy (exported)
- when a client requests a device that isn't exportable,
usbip attach -r server_name -b 3-10.4
usbip: error: Attach Request for 3-10.4 failed - Device not found
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ST_OK and ST_NA are the only values used to communicate
status of a request from a client. Use new error codes to clearly
indicate what failed. For example, when client sends request to
import a device that isn't export-able, send ST_DEV_BUSY to the client.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ST_OK and ST_NA are the only values defined to communicate
status of a request from a client. Add more error codes to clearly
indicate what failed. For example, when client sends request to import
a device that isn't export-able, server can send a specific error code
to the client.
Existing defines are moved to a common header in libsrc to be included
in the libusbip_la-usbip_common.o to be used by all the usbip tools.
Supporting interface to print error strings is added to the common lib.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel and tool version mismatch message is cryptic. Fix it to be
informative.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attach device error message is cryptic and useless. Fix it to be
informative.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dev is initialized and then re-assigned with the same value
a little later, hence the second assignment is redundant and can be
removed.
Cleans up clang warning:
drivers/usb/wusbcore/wa-nep.c:88:17: warning: Value stored to 'dev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usbip supports USB3, the maximum number of ports allowed
on a hub is 15 (USB_SS_MAXPORTS), not 31 (USB_MAXCHILDREN).
Reported-by: Gianluigi Tiesi <sherpya@netfarm.it>
Reported-by: Borissh1983 <borissh1983@gmail.com>
References: https://bugs.debian.org/878866
Fixes: 1c9de5bf42 ("usbip: vhci-hcd: Add USB3 SuperSpeed support")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the commit 835e4241e7 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e7 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Wang says:
====================
Several fixes for vhost_net ptr_ring usage
This small series try to fix several bugs of ptr_ring usage in
vhost_net. Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit fc72d1d54d ("tuntap: XDP transmission"), we can
actually queueing XDP pointers in the pointer ring, so we should
examine the pointer type before freeing the pointer.
Fixes: fc72d1d54d ("tuntap: XDP transmission")
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get pointer ring from the exported sock, this means we should keep
rx_ring and vq->private synced during both vq stop and backend set,
otherwise we may see stale rx_ring.
Fixes: c67df11f6e ("vhost_net: try batch dequing from skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b5a4b4bf2 ("power: supply: axp288_fuel_gauge: Rework
get_status()"), switched from 0A current detection to using the capacity
register for full detection.
It turns out this fixes full reporting on some devices which keep trickle
charging long after the capacity register reach 100%, but breaks it on
some other devices where the charger stops charging before the capacity
register reaches 100%. This commit fixes this by also checking for
0A current when the reported capacity is above 90%.
Fixes: 2b5a4b4bf2 ("psy: axp288_fuel_gauge: Rework get_status()")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>