Commit graph

27,507 commits

Author SHA1 Message Date
Steve Rutherford
1c1a9ce973 KVM: x86: Add support for local interrupt requests from userspace
In order to enable userspace PIC support, the userspace PIC needs to
be able to inject local interrupts even when the APICs are in the
kernel.

KVM_INTERRUPT now supports sending local interrupts to an APIC when
APICs are in the kernel.

The ready_for_interrupt_request flag is now only set when the CPU/APIC
will immediately accept and inject an interrupt (i.e. APIC has not
masked the PIC).

When the PIC wishes to initiate an INTA cycle with, say, CPU0, it
kicks CPU0 out of the guest, and renedezvous with CPU0 once it arrives
in userspace.

When the CPU/APIC unmasks the PIC, a KVM_EXIT_IRQ_WINDOW_OPEN is
triggered, so that userspace has a chance to inject a PIC interrupt
if it had been pending.

Overall, this design can lead to a small number of spurious userspace
renedezvous. In particular, whenever the PIC transistions from low to
high while it is masked and whenever the PIC becomes unmasked while
it is low.

Note: this does not buffer more than one local interrupt in the
kernel, so the VMM needs to enter the guest in order to complete
interrupt injection before injecting an additional interrupt.

Compiles for x86.

Can pass the KVM Unit Tests.

Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:29 +02:00
Steve Rutherford
b053b2aef2 KVM: x86: Add EOI exit bitmap inference
In order to support a userspace IOAPIC interacting with an in kernel
APIC, the EOI exit bitmaps need to be configurable.

If the IOAPIC is in userspace (i.e. the irqchip has been split), the
EOI exit bitmaps will be set whenever the GSI Routes are configured.
In particular, for the low MSI routes are reservable for userspace
IOAPICs. For these MSI routes, the EOI Exit bit corresponding to the
destination vector of the route will be set for the destination VCPU.

The intention is for the userspace IOAPICs to use the reservable MSI
routes to inject interrupts into the guest.

This is a slight abuse of the notion of an MSI Route, given that MSIs
classically bypass the IOAPIC. It might be worthwhile to add an
additional route type to improve clarity.

Compile tested for Intel x86.

Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:28 +02:00
Steve Rutherford
7543a635aa KVM: x86: Add KVM exit for IOAPIC EOIs
Adds KVM_EXIT_IOAPIC_EOI which allows the kernel to EOI
level-triggered IOAPIC interrupts.

Uses a per VCPU exit bitmap to decide whether or not the IOAPIC needs
to be informed (which is identical to the EOI_EXIT_BITMAP field used
by modern x86 processors, but can also be used to elide kvm IOAPIC EOI
exits on older processors).

[Note: A prototype using ResampleFDs found that decoupling the EOI
from the VCPU's thread made it possible for the VCPU to not see a
recent EOI after reentering the guest. This does not match real
hardware.]

Compile tested for Intel x86.

Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:27 +02:00
Steve Rutherford
49df6397ed KVM: x86: Split the APIC from the rest of IRQCHIP.
First patch in a series which enables the relocation of the
PIC/IOAPIC to userspace.

Adds capability KVM_CAP_SPLIT_IRQCHIP;

KVM_CAP_SPLIT_IRQCHIP enables the construction of LAPICs without the
rest of the irqchip.

Compile tested for x86.

Signed-off-by: Steve Rutherford <srutherford@google.com>
Suggested-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:26 +02:00
Mauro Carvalho Chehab
1ccd66cca9 [media] DocBook: add the new videobuf2-v4l2 header
This header should also be used to generate documentation. So,
add it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-10-01 09:18:09 -03:00
Andrzej Pietrasiewicz
6c96dbbc2a [media] s5p-jpeg: add support for 5433
JPEG IP found in Exynos5433 is similar to what is in Exynos4, but
there are some subtle differences which this patch takes into account.

The most important difference is in what is processed by the JPEG IP and
what has to be provided to it. In case of 5433 the IP does not parse
Huffman and quantisation tables, so this has to be performed with the CPU
and the majority of the code in this patch does that.

A small but important difference is in what address is passed to the JPEG
IP. In case of 5433 it is the SOS (start of scan) position, which is
natural, because the headers must be parsed elsewhere.

There is also a difference in how the hardware is put to work in
device_run.

Data structures are extended as appropriate to accommodate the above
changes.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-10-01 08:40:04 -03:00
Hans Verkuil
60f4570de8 [media] DocBook/media: clarify control documentation
- Add missing V4L2_CTRL_TYPE_U32 documentation
- Remove 'which are actually different on the hardware' sentence which
  is confusing. I think the idea was to let the user know that the step can
  be different for different hardware, but that's obvious because otherwise
  you wouldn't need to specify the step value.
- Clarify that V4L2_CTRL_COMPOUND_TYPES also applies to arrays.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-10-01 08:31:57 -03:00
Ingo Molnar
b2f73922d1 fs/proc, core/debug: Don't expose absolute kernel addresses via wchan
So the /proc/PID/stat 'wchan' field (the 30th field, which contains
the absolute kernel address of the kernel function a task is blocked in)
leaks absolute kernel addresses to unprivileged user-space:

        seq_put_decimal_ull(m, ' ', wchan);

The absolute address might also leak via /proc/PID/wchan as well, if
KALLSYMS is turned off or if the symbol lookup fails for some reason:

static int proc_pid_wchan(struct seq_file *m, struct pid_namespace *ns,
                          struct pid *pid, struct task_struct *task)
{
        unsigned long wchan;
        char symname[KSYM_NAME_LEN];

        wchan = get_wchan(task);

        if (lookup_symbol_name(wchan, symname) < 0) {
                if (!ptrace_may_access(task, PTRACE_MODE_READ))
                        return 0;
                seq_printf(m, "%lu", wchan);
        } else {
                seq_printf(m, "%s", symname);
        }

        return 0;
}

This isn't ideal, because for example it trivially leaks the KASLR offset
to any local attacker:

  fomalhaut:~> printf "%016lx\n" $(cat /proc/$$/stat | cut -d' ' -f35)
  ffffffff8123b380

Most real-life uses of wchan are symbolic:

  ps -eo pid:10,tid:10,wchan:30,comm

and procps uses /proc/PID/wchan, not the absolute address in /proc/PID/stat:

  triton:~/tip> strace -f ps -eo pid:10,tid:10,wchan:30,comm 2>&1 | grep wchan | tail -1
  open("/proc/30833/wchan", O_RDONLY)     = 6

There's one compatibility quirk here: procps relies on whether the
absolute value is non-zero - and we can provide that functionality
by outputing "0" or "1" depending on whether the task is blocked
(whether there's a wchan address).

These days there appears to be very little legitimate reason
user-space would be interested in  the absolute address. The
absolute address is mostly historic: from the days when we
didn't have kallsyms and user-space procps had to do the
decoding itself via the System.map.

So this patch sets all numeric output to "0" or "1" and keeps only
symbolic output, in /proc/PID/wchan.

( The absolute sleep address can generally still be profiled via
  perf, by tasks with sufficient privileges. )

Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: kasan-dev <kasan-dev@googlegroups.com>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20150930135917.GA3285@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-10-01 12:55:34 +02:00
Hans Verkuil
00507a8d6a [media] DocBook media: Document the SMPTE 2084 transfer function
Document this new transfer function used by High Dynamic Range content.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-10-01 07:46:55 -03:00
James Liao
5661848956 dt-bindings: ARM: Mediatek: Document devicetree bindings for clock controllers
This adds the binding documentation for the mmsys, imgsys, vdecsys,
vencsys and vencltsys controllers found on Mediatek SoCs.

Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
2015-10-01 12:04:50 +08:00
Andreas Dannenberg
6169588f69 Documentation: power: bq24257: Document exported sysfs entries
Document the settings exported by bq24257 charger driver through sysfs
entries:
- ovp_voltage
- in_dpm_voltage
- high_impedance_enable
- sysoff_enable

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-10-01 03:57:57 +02:00
Hans Verkuil
7146a9cfa4 [media] DocBook media: document the new DCI-P3 colorspace
Document this colorspace.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-09-30 19:43:35 -03:00
Clément Vuchener
6f78193ee9 HID: corsair: Add Corsair Vengeance K90 driver
This patch implements a HID driver for the Corsair Vengeance K90 keyboard.

It fixes the behaviour of the keys using incorrect HID usage codes and exposes
the macro playback mode and current profile to the user space through sysfs
attributes. It also adds two LED class devices controlling the "record" LED and
the backlight.

Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-09-30 21:28:10 +02:00
Peter Rosin
b15aef8d5b iio: resistance: Document that resistance can be output
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-09-30 18:20:53 +01:00
Yoshihiro Shimoda
f5f6afa85a usb: renesas_usbhs: Add support for R-Car H3
This patch adds a compatible string to support for R-Car H3.

Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.

Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-09-30 11:21:11 -05:00
Daniel Vetter
0aaf20cff6 drm/drm_ioctl.c: kerneldoc
As usual pull it into the drm docbook template, too. And again as
usual I've decided to only document stuff exported to drivers, so all
the old leftover markup from the shared drm repo days lost the magic
** signature.

Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-09-30 10:48:20 +02:00
Daniel Vetter
6e3f797c9a drm/doc: Update docs about device instance setup
->load is deprecated, bus functions are deprecated and everyone
should use drm_dev_alloc&register.

So update the .tmpl (and pull a bunch of the overview docs into the
sourcecode to increase chances that it'll stay in sync in the future)
and add notes to functions which are deprecated. I didn't bother to
clean up and document the unload sequence similarly since that one is
still a bit a mess: drm_dev_unregister does way too much,
drm_unplug_dev does what _unregister should be doing but then has the
complication of promising something it doesn't actually do (it doesn't
unplug existing open fds for instance, only prevents new ones).

Motivated since I don't want to hunt every new driver for usage of
drm_platform_init any more ;-)

v2: Reword the deprecation note for ->load a bit, using Laurent's
suggestion as an example (but making the wording a bit stronger even).
Fix spelling in commit message.

v3: More spelling fixes from Laurent.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30 10:06:06 +02:00
Daniel Vetter
44cc6c08da Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-09-30 08:47:41 +02:00
Thomas Huth
9ae6d4935e testptp: Silence compiler warnings on ppc64
When compiling Documentation/ptp/testptp.c the following compiler
warnings are printed out:

Documentation/ptp/testptp.c: In function ‘main’:
Documentation/ptp/testptp.c:367:11: warning: format ‘%lld’ expects argument
    of type ‘long long int’, but argument 3 has type ‘__s64’ [-Wformat=]
           event.t.sec, event.t.nsec);
           ^
Documentation/ptp/testptp.c:505:5: warning: format ‘%lld’ expects argument
    of type ‘long long int’, but argument 2 has type ‘__s64’ [-Wformat=]
     (pct+2*i)->sec, (pct+2*i)->nsec);
     ^
Documentation/ptp/testptp.c:507:5: warning: format ‘%lld’ expects argument
    of type ‘long long int’, but argument 2 has type ‘__s64’ [-Wformat=]
     (pct+2*i+1)->sec, (pct+2*i+1)->nsec);
     ^
Documentation/ptp/testptp.c:509:5: warning: format ‘%lld’ expects argument
    of type ‘long long int’, but argument 2 has type ‘__s64’ [-Wformat=]
     (pct+2*i+2)->sec, (pct+2*i+2)->nsec);

This happens because __s64 is by default defined as "long" on ppc64,
not as "long long". However, to fix these warnings, it's possible to
define the __SANE_USERSPACE_TYPES__ so that __s64 gets defined to
"long long" on ppc64, too.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29 21:16:56 -07:00
Greg Kroah-Hartman
9f827d8099 First round of new driver, new functionality and cleanups for IIO in the 4.4 cycle
New device support
 * APDS9960 ALS + proximity driver
 * bmg160 SPI devices.
 * HDC100x humidity sensors
 * Holt HI-8435 threshold detector
 * mma8453Q accelerometer added to the mma8452 driver
 * mma86452FC and mma8653FC accelerometers added to the mma8452 driver
 * mxc4005 accelerometer
 * PulsedLight LIDAR
 * SensorTech VZ89x volatile organic compound sensor
 * UPISEMI uS5182d ALS and proximity sensors
 
 New core functionality
 * triggered events - use triggers to check for changes in threshold type
   detectors on devices with out interrupt support.  First user is the holt
   comparator.
 * chemical concentration and resistance channel types.
 
 New driver functionality
 * vf610
   - buffer support.
   - followup coccinelle warning fix.
 
 Core rework
 * buffers
   - break out callback buffer to own module.
   - move buffer implementations to a new subdirectory
 * percolate the error code form iio_event_getfd out to userspace
   rather than giving a missleading error later on.
 
 Cleanups
 * adddac drivers
   - use BIT macro where appropriate.
 * meter drivers
   - use BIT macro where appropriate.
 
 * ad7303
  - add an OF match table to line up with the binding docs.
 * adc128s052
   - add an OF match table to line up with the binding docs.
 * adf4350
   - add an OF match table to line up with the binding docs
 * as3935
   - add an OF match table to line up with the binding docs.
 * berlin2-adc
   - use GENMASK and BIT for masks
   - prevent attempting to sample multiple channels at once by moving a
     mutex scop
   - coding style cleanups
 * bmg150_magn
   - kconfig sort order was wrong - fix it.
 * bmg160
   - use i2c regmap and drop all uses of i2c_client
   - separate i2c and core driver
 * cc10001_adc
   - kconfig sort order was wrong - fix it.
 * evgen (dummy driver helper module)
   - move interrupt generation to irq_work to reduce differences between
     the dummy driver and real hardware drivers.
 * hmc5843
   - set the name dynamically rather than to a fixed value for one of the
     suported parts.
   - export module alias information to allow autoprobing of module.
 * lpc32xx
   - on failure to get resource or irq return -ENXIO as uppose to -EBUSY
 * max1027
   - set .of_match_table to actually allow OF style matching.
 * max5821
   - add MODULE_DEVICE_TABLE for OF table.
 * mma8452
   - refactor to separate out chip specific data.
   - add freefall / motion interrupt source for devices that do their
     interrupts slightly differently.
   - update copywrite notice.
   - leave naming of events directory in sysfs to the core
 * mcp320x
   - set .of_match_table so that it can be use for OF style matching.
 * mlx90614
   - Implement filter configuration (note the datasheet changed as a result
     of the driver reviews to include the values we needed ;)
 * opt3001
   - drop .owner field as assigned by platform driver core.
 * si7020
   - replace a bitmask on the humidity values with a more correct range
     check.
 * stk310
   - improved error handling.
   - use BIT macro where appropriate and use the resulting defines
     instead of magic numbers in the code.
   - fix indentation
 * st-sensors
   - add debugfs register read hook
 * tsl4531
   - fix error handling in check_id
 * twl6030
   - fix module autoload for OF
 * iio-trig-sysfs
   - document add and remove attribute
 * trigger in staging
   - code alignment fixes.
   - braces on both branches of if statement if needed for one.
 * xilinx-xadc
   - push interrupts into hardirq context as there isn't much in them
     any more and it avoids breaking PREEMPT_RT builds due to the use
     of a spinlock between the hardirq and the thread.
 
 Tools
 * event-monitor
   - report unsupported events.  We keep expanding what can come from drivers
     so give a helpful error if one turns up in an out of date userspace
     program.
 * generic-buffer
   - helpful message about needing to enable a channel to start the buffer.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJWBDeHAAoJEFSFNJnE9BaIgSQP/183S1WJTqpsrz3APZY4qQLU
 m8Jv6VCvtSENpryUxn6MtfPuVeBa8LwhciAtelsJfVvu2O902VAOcsgMhgp3cz7Y
 daTXio/XhdA7YJvuOkycLD3CdWJ7Gb3+nieBmcEb0YMAMIgchMR+gI/LYR/htISz
 Req9EM8C/4sU5hn3r92mVZFMiV5XWsApCv61A6IzXdaz4YgiEjtFb8NF87IPlFq0
 Rpg3BG4/9Ka1tUaZs6a98sWXqudCzHSetKk9GLFbnhoo6xC+C33b06Z+fSinAZmn
 FsVGfQ/I6xhFJmCJLifLq/voN9gbDuebUQCPIYPfu7Oby29JcK95P60ZHM954s2M
 DGTCQ44GTReA2IqRvxlgQDU/TBUTwWKKDnuelw6+387t/wT0tnnfkwFrps1xPqGy
 k1qHVViofzf3iSKdDKeQyMjDoO+nMUv0DdkzYNz4xCPQIhGMRXA/Q+U81tJvJHZl
 rwhHVruFHyhI1/sTvTMJ/5+F7lL7LieFdCTVnzl0QblzMskGpLy5d/fMJn8OLVqa
 6PiA5x3799U2o67wtCYH+RoSdQj1U+qEFkg7Oe+nVvlpbs/vfdR2dI3wYfp8459l
 mjafTgW8R+7tXYKU+iSKA4660QIN9LR6byBqyxX97mjyYxn3ml3VWJ44ztqfhjZd
 1ZyZxsWa2y5b6L017kJN
 =E+jf
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of new driver, new functionality and cleanups for IIO in the 4.4 cycle

New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors

New core functionality
* triggered events - use triggers to check for changes in threshold type
  detectors on devices with out interrupt support.  First user is the holt
  comparator.
* chemical concentration and resistance channel types.

New driver functionality
* vf610
  - buffer support.
  - followup coccinelle warning fix.

Core rework
* buffers
  - break out callback buffer to own module.
  - move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
  rather than giving a missleading error later on.

Cleanups
* adddac drivers
  - use BIT macro where appropriate.
* meter drivers
  - use BIT macro where appropriate.

* ad7303
 - add an OF match table to line up with the binding docs.
* adc128s052
  - add an OF match table to line up with the binding docs.
* adf4350
  - add an OF match table to line up with the binding docs
* as3935
  - add an OF match table to line up with the binding docs.
* berlin2-adc
  - use GENMASK and BIT for masks
  - prevent attempting to sample multiple channels at once by moving a
    mutex scop
  - coding style cleanups
* bmg150_magn
  - kconfig sort order was wrong - fix it.
* bmg160
  - use i2c regmap and drop all uses of i2c_client
  - separate i2c and core driver
* cc10001_adc
  - kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
  - move interrupt generation to irq_work to reduce differences between
    the dummy driver and real hardware drivers.
* hmc5843
  - set the name dynamically rather than to a fixed value for one of the
    suported parts.
  - export module alias information to allow autoprobing of module.
* lpc32xx
  - on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
  - set .of_match_table to actually allow OF style matching.
* max5821
  - add MODULE_DEVICE_TABLE for OF table.
* mma8452
  - refactor to separate out chip specific data.
  - add freefall / motion interrupt source for devices that do their
    interrupts slightly differently.
  - update copywrite notice.
  - leave naming of events directory in sysfs to the core
* mcp320x
  - set .of_match_table so that it can be use for OF style matching.
* mlx90614
  - Implement filter configuration (note the datasheet changed as a result
    of the driver reviews to include the values we needed ;)
* opt3001
  - drop .owner field as assigned by platform driver core.
* si7020
  - replace a bitmask on the humidity values with a more correct range
    check.
* stk310
  - improved error handling.
  - use BIT macro where appropriate and use the resulting defines
    instead of magic numbers in the code.
  - fix indentation
* st-sensors
  - add debugfs register read hook
* tsl4531
  - fix error handling in check_id
* twl6030
  - fix module autoload for OF
* iio-trig-sysfs
  - document add and remove attribute
* trigger in staging
  - code alignment fixes.
  - braces on both branches of if statement if needed for one.
* xilinx-xadc
  - push interrupts into hardirq context as there isn't much in them
    any more and it avoids breaking PREEMPT_RT builds due to the use
    of a spinlock between the hardirq and the thread.

Tools
* event-monitor
  - report unsupported events.  We keep expanding what can come from drivers
    so give a helpful error if one turns up in an out of date userspace
    program.
* generic-buffer
  - helpful message about needing to enable a channel to start the buffer.
2015-09-30 03:37:48 +02:00
S Twiss
a27b5e0a78 Input: add DA9062 OnKey capability to DA9063 OnKey driver
Add DA9062 OnKey support into the existing DA9063 OnKey driver component by
using generic access tables for common register and bit mask definitions.

The following change will add generic register and bit mask support to the
DA9063 OnKey.

The following alterations have been made to the DA9063 OnKey:

- Addition of a da906x_chip_config structure to hold all
  generic registers and bitmasks for this type of OnKey component.
- Addition of an struct of_device_id table for DA9063 and DA9062
  defaults
- Refactoring functions to use struct da9063_onkey accesses to generic
  registers/masks instead of using defines from registers.h
- Re-work of da9063_onkey_probe() to use of_match_node() and
  dev_get_regmap() to provide initialisation of generic registers and
  masks and access to regmap

Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-09-29 16:50:07 -07:00
Dmitry Torokhov
8f697e5740 Linux 4.3-rc3
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
 SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
 qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
 wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
 tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
 TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
 =m29x
 -----END PGP SIGNATURE-----

Merge tag 'v4.3-rc3' into next

Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
2015-09-29 16:28:52 -07:00
Dave Airlie
2d4df13c0f Merge tag 'topic/drm-misc-2015-09-25' of git://anongit.freedesktop.org/drm-intel into drm-next
Another attempt at drm-misc for 4.4 ...
- better atomic helpers for runtime pm drivers
- atomic fbdev
- dp aux i2c STATUS_UPDATE handling (for short i2c replies from the sink)
- bunch of constify patches
- inital kerneldoc for vga switcheroo
- some vblank code cleanups from Ville and Thierry
- various polish all over

* tag 'topic/drm-misc-2015-09-25' of git://anongit.freedesktop.org/drm-intel: (57 commits)
  drm/irq: Add drm_crtc_vblank_count_and_time()
  drm/irq: Rename drm_crtc -> crtc
  drm: drm_atomic_crtc_get_property should be static
  drm/gma500: Remove DP_LINK_STATUS_SIZE redefinition
  vga_switcheroo: Set active attribute to false for audio clients
  drm/core: Preserve the fb id on close.
  drm/core: Preserve the framebuffer after removing it.
  drm: Use vblank timestamps to guesstimate how many vblanks were missed
  drm: store_vblank() is never called with NULL timestamp
  drm: Clean up drm_calc_vbltimestamp_from_scanoutpos() vbl_status
  drm: Limit the number of .get_vblank_counter() retries
  drm: Pass flags to drm_update_vblank_count()
  drm/i915: Fix vblank count variable types
  drm: Kill pixeldur_ns
  drm: Stop using linedur_ns and pixeldur_ns for vblank timestamps
  drm: Move timestamping constants into drm_vblank_crtc
  drm/fbdev: Update legacy plane->fb refcounting for atomic restore
  drm: fix kernel-doc warnings in drm_crtc.h
  vga_switcheroo: Sort headers alphabetically
  drm: Spell vga_switcheroo consistently
  ...
2015-09-30 08:35:45 +10:00
Eduardo Valentin
b840b6e65c thermal: ti-soc-thermal: add OMAP36xx support
Add OMAP36xx support to ti-soc-thermal driver. This
chip is also unreliable. The data provided here is
based on OMAP36xx TRM:
http://www.ti.com/lit/ug/swpu177aa/swpu177aa.pdf

Signed-off-by: Eduardo Valentin <edubezva@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2015-09-29 14:13:19 -07:00
Pavel Machek
9c5c87e593 ti-soc-thermal: implement omap3 support
This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2015-09-29 14:08:24 -07:00
Stefan Agner
8a79959000 mtd: nand: vf610_nfc: add device tree bindings
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
[Brian: fixup #size-cells in example]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-09-29 13:54:54 -07:00
Vladimir Zapolskiy
961a86d22e doc: dt: arm,pl172: add description of PL175 and PL176 controllers
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
2015-09-29 22:19:02 +02:00
Magnus Damm
e7dbe2da5e irqchip/renesas-irqc: Add r8a7795 INTC-EX DT documentation
For some reason the name of the external interrupt controller
has changed name with r8a7795, so use "intc-ex" instead of "irqc"
as r8a7795 compat string to follow the friendly documentation.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: horms@verge.net.au
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: jason@lakedaemon.net
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20150928094228.32552.83336.sendpatchset@little-apple
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-09-29 20:41:00 +02:00
Geert Uytterhoeven
eb8d0ac4af spi: sh-msiof: Match renesas,rx-fifo-size in DT bindings doc with driver
Commit fe78d0b769 ("spi: sh-msiof: Fix FIFO size to 64 word from
256 word") changed the default RX FIFO size on R-Car Gen2 SoCs in the
driver code, but forgot to update the DT bindings documentation.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-09-29 17:13:47 +01:00
Andreas Dannenberg
fff59df105 dt: power: bq24257-charger: Cover additional devices
Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-29 16:49:58 +02:00
Thomas Petazzoni
d492cccac2 ARM: mvebu: add support to clear shared L2 bit on Armada XP
For optimal performance, in a HW I/O coherency context such as the one
used on Armada XP, the shared L2 bit of the CPU configuration register
should be cleared.

This commit adjusts the coherency fabric code used by Marvell EBU
processors to clear this bit on Armada XP. Since it's a per-CPU
register, it's cleared in set_cpu_coherent() for the boot CPU, and
through a CPU notifier for the non-boot CPUs.

[gregory.clement@free-electrons.com: rebasd on 4.3-rc1]

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2015-09-29 15:31:51 +02:00
Aravind Gopalakrishnan
6b7464b703 Documentation/EDAC: Add reference documents section for amd64_edac
This section used to be in amd64_edac.h. Move it here as it is a more
natural place to put all documentation-related info. Add links to the
BKDGs while at it.

Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Cc: linux-doc@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1443440671-2400-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
2015-09-29 13:42:41 +02:00
Takashi Iwai
d8dfacf8b5 Merge branch 'topic/firewire-update' into for-next 2015-09-29 12:52:07 +02:00
Steffen Klassert
c386578f1c xfrm: Let the flowcache handle its size by default.
The xfrm flowcache size is limited by the flowcache limit
(4096 * number of online cpus) and the xfrm garbage collector
threshold (2 * 32768), whatever is reached first. This means
that we can hit the garbage collector limit only on systems
with more than 16 cpus. On such systems we simply refuse
new allocations if we reach the limit, so new flows are dropped.
On syslems with 16 or less cpus, we hit the flowcache limit.
In this case, we shrink the flow cache instead of refusing new
flows.

We increase the xfrm garbage collector threshold to INT_MAX
to get the same behaviour, independent of the number of cpus.

The xfrm garbage collector threshold can still be set below
the flowcache limit to reduce the memory usage of the flowcache.

Tested-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2015-09-29 11:44:16 +02:00
James Morris
0266715155 Merge tag 'keys-fixes-20150925' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into for-linus
Keyrings fixes from David Howells, for current Linus.
2015-09-29 19:19:09 +10:00
Greg Kroah-Hartman
60f593977b Merge 4.3-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29 02:14:46 +02:00
Sudeep Holla
80f390ea5a Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
This patch adds devicetree binding for System Control and Power
Interface (SCPI) Message Protocol used between the Application Cores(AP)
and the System Control Processor(SCP). The MHU peripheral provides a
mechanism for inter-processor communication between SCP's M3 processor
and AP.

SCP offers control and management of the core/cluster power states,
various power domain DVFS including the core/cluster, certain system
clocks configuration, thermal sensors and many others.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
CC: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: devicetree@vger.kernel.org
2015-09-28 11:53:37 +01:00
Ben Hutchings
b479bfd00e DocBook: Use a fixed encoding for output
Currently the encoding of documents generated by DocBook depends on
the current locale.  Make the output reproducible independently of
the locale, by setting the encoding to UTF-8 (LC_CTYPE=C.UTF-8) by
preference, or ASCII (LC_CTYPE=C) as a fallback.

LC_CTYPE can normally be overridden by LC_ALL, but the top-level
Makefile unsets that.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[jc: added check-lc_ctype to .gitignore]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-09-28 01:31:48 -06:00
Dmitry Torokhov
f0bef75c59 Input: edt-ft5x06 - do not hardcode interrupt trigger type
Instead of hardcoding IRQ trigger type to IRQF_TRIGGER_FALLING, let's
respect settings specified in device tree. To be compatible with older
DTSes, if trigger type is not set up in DTS we'll set it to default
(falling edge).

Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-09-27 17:34:00 -07:00
Franklin S Cooper Jr
13c23cd18b Input: edt-ft5x06 - switch to newer gpio framework
The current/old gpio framework used doesn't properly listen to
ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
account these flags when setting gpio values.

Since the values being output were based on voltage and not logic they
change to reflect this difference. Also use gpiod_set_value_cansleep since
wake and reset pins can be provided by bus based io expanders.

Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
warning.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-09-27 17:33:58 -07:00
Linus Torvalds
097f70b3c4 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
 - Properly setup irq handling for ATH79 platforms
 - Fix bootmem mapstart calculation for contiguous maps
 - Handle little endian and older CPUs correct in BPF
 - Fix console for Fulong 2E systems
 - Handle FTLB correctly on R6 CPUs
 - Fixes for CM, GIC and MAAR support code

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Initialise MAARs on secondary CPUs
  MIPS: print MAAR configuration during boot
  MIPS: mm: compile maar_init unconditionally
  irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
  irqchip: mips-gic: Convert CPU numbers to VP IDs.
  MIPS: CM: Provide a function to map from CPU to VP ID.
  MIPS: Fix FTLB detection for R6
  MIPS: cpu-features: Add cpu_has_ftlb
  MIPS: ATH79: Add irq chip ar7240-misc-intc
  MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
  MIPS: BPF: Fix build on pre-R2 little endian CPUs
  MIPS: BPF: Avoid unreachable code on little endian
  MIPS: bootmem: Fix mapstart calculation for contiguous maps
  MIPS: Fix console output for Fulong2e system
2015-09-27 18:22:34 -04:00
Greg Kroah-Hartman
c566f36543 Merge 4.3-rc3 into char-misc-next
We want those fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-27 12:44:02 -07:00
Nikhil Badola
3737c54418 Documentation: dt: dwc3: Add snps,quirk-frame-length-adjustment property
Add snps,quirk-frame-length-adjustment property which provides value
for post silicon frame length adjustment

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-09-27 10:54:31 -05:00
Linus Torvalds
bcba282ab3 USB fixes for 4.3-rc3
Here are some USB driver fixes for 4.3-rc3.
 
 There's the usual assortment of new device ids, combined with xhci and
 gadget driver fixes.  Full details in the shortlog.  All of these have
 been in linux-next with no reported problems.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlYGzJ0ACgkQMUfUDdst+yneGACgxrj/ZJGgY09tkItvvejHoYrF
 tgQAoI/cRL7C9aoWt7DjMxmbFnQE8hC7
 =jsj/
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes for 4.3-rc3.

  There's the usual assortment of new device ids, combined with xhci and
  gadget driver fixes.  Full details in the shortlog.  All of these have
  been in linux-next with no reported problems"

* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
  MAINTAINERS: remove amd5536udc USB gadget driver maintainer
  USB: whiteheat: fix potential null-deref at probe
  xhci: init command timeout timer earlier to avoid deleting it uninitialized
  xhci: change xhci 1.0 only restrictions to support xhci 1.1
  usb: xhci: exit early in xhci_setup_device() if we're halted or dying
  usb: xhci: stop everything on the first call to xhci_stop
  usb: xhci: Clear XHCI_STATE_DYING on start
  usb: xhci: lock mutex on xhci_stop
  xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
  xhci: give command abortion one more chance before killing xhci
  usb: Use the USB_SS_MULT() macro to get the burst multiplier.
  usb: dwc3: gadget: Fix BUG in RT config
  usb: musb: fix cppi channel teardown for isoch transfer
  usb: phy: isp1301: Export I2C module alias information
  usb: gadget: drop null test before destroy functions
  usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
  usb: gadget: dummy_hcd: fix rescan logic for transfer
  usb: gadget: dummy_hcd: fix unneeded else-if condition
  usb: gadget: dummy_hcd: emulate sending zlp in packet logic
  usb: musb: dsps: fix polling in device-only mode
  ...
2015-09-26 21:00:28 -04:00
David S. Miller
4963ed48f2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	net/ipv4/arp.c

The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-26 16:08:27 -07:00
Linus Torvalds
518a7cb698 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
    instead of cloning them.  From Daniel Borkmann.

 2) When converting classical BPF into eBPF, fix the setting of the
    source reg to BPF_REG_X.  From Tycho Andersen.

 3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
    Linus Lussing.

 4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.

 5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
    Roopa Prabhu.

 6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.

 7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
    Florian Westphal.

 8) Check DMA mapping errors in bna driver, from Ivan Vecera.

 9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
    misclearing of interrupt status in TX timeout handler, etc.) from
    David Woodhouse.

10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
    Hugne.

11) Fix autobind races et al. in netlink code, from Herbert Xu with
    help from Tejun Heo and others.

12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.

13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
    Eric Dumazet.

14) Fix array overruns in mac80211, from Johannes Berg and Dan
    Carpenter.

15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.

16) Fix race between poll_one_napi and napi_disable, from Neil Horman.

17) Fix byte order in geneve tunnel port config, from John W Linville.

18) Fix handling of ARP replies over lightweight tunnels, from Jiri
    Benc.

19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
    Kok and Roopa Prabhu.

20) Several reference count handling bug fixes in the PHY/MDIO layer
    from Russel King.

21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.

22) Fix crash in icmp_route_lookup(), from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  net: Fix panic in icmp_route_lookup
  net: update docbook comment for __mdiobus_register()
  ppp: fix lockdep splat in ppp_dev_uninit()
  net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
  phy: marvell: add link partner advertised modes
  net: fix net_device refcounting
  phy: add phy_device_remove()
  phy: fixed-phy: properly validate phy in fixed_phy_update_state()
  net: fix phy refcounting in a bunch of drivers
  of_mdio: fix MDIO phy device refcounting
  phy: add proper phy struct device refcounting
  phy: fix mdiobus module safety
  net: dsa: fix of_mdio_find_bus() device refcount leak
  phy: fix of_mdio_find_bus() device refcount leak
  ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
  ip6_gre: Reduce log level in ip6gre_err() to debug
  fib_rules: fix fib rule dumps across multiple skbs
  bnx2x: byte swap rss_key to comply to Toeplitz specs
  net: revert "net_sched: move tp->root allocation into fw_init()"
  lwtunnel: remove source and destination UDP port config option
  ...
2015-09-26 06:01:33 -04:00
Ray Jui
8d0afa1a93 PCI: iproc: Update PCIe device tree bindings
Update the device tree bindings with added support for outbound mapping
configurations.

Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-09-25 18:19:46 -05:00
Darek Zielski
63ab664ceb [media] saa7134: add Leadtek Winfast TV2100 FM card support
Add Leadtek Winfast TV2100 FM card to saa7134 driver. It is a card bearing
SAA7130HL chip.

Signed-off-by: Darek Zielski <dz1125tor@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-09-25 17:19:17 -03:00
stephen hemminger
008aa6a4fa l2tp: remove references to modprobe in documentation
No longer need explicit modprobe's and update to use ip instead
of deprecated ifconfig command.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 12:27:23 -07:00
Linus Torvalds
966966a630 PCI updates for v4.3:
Resource management
     - Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
     - Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
 
   MSI
     - Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
 
   Renesas R-Car host bridge driver
     - Add R8A7794 support (Sergei Shtylyov)
 
   Miscellaneous
     - Fix devfn for VPD access through function 0 (Alex Williamson)
     - Use function 0 VPD only for identical functions (Alex Williamson)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWBUq2AAoJEFmIoMA60/r8wbwP/0D/+fKEPYJlB6hx1wLHpVk3
 K//vEwH0RgA3v2X53QUoHg94gTYhSZLKX0zdAFshbphE0HCZ6AO3UO+/ZJ3cui6J
 PYvKOnhby2ErNotZqrs3DQIM8rGgl0ZVgoFQrAWEvwiHRHI/r2ArK/oR4PiBjxJT
 StYuJoTkZIlJyHXza6tvHDcWi+Jc8t8r0HC4Vs32BlaVBQM0SH3CMxHfhJw/Q9xP
 WHFif1sH0N+p7WDyHH71C1T8POOgXY73BsD2AC0se3lRYZ9SVkOVy9ECGUucx8F6
 LDAuFelwRvW2Dr9kh38+5f8Xp155E+eZ6zRWW9/JlrUKVEtHhOFhtrRfDNKHuDCt
 B9ETrxDiSUFAdQ2weye9BK6aXK0CHF6YP3PCbvK77qFUUsN8csFSKktanKrFAbML
 CdjkVkEoeLHw+aXzyDg0pSBRZMQ24dTQDh7YqOFZGuEjCLPXOEQ8nitf0IzBB0KI
 4QetT/QK3bKkgtVKTwPP+s9f4g+fA/oiwJ21ZTV9hi/9upywTa/umCUvH9Fmb8Fp
 VZeTzugSht0+ioXpaF/6/KO0Ccp/t5uAHYeuBBMqiHX7ks8DdnfPCwbWNRKkg25O
 Qy7Y8VnnOtesRCAqBq5y/hHlLUluMkjYpEblYFiD6HBWcjUh6xE6LlIO4mwnjqWI
 zjB3w7+0GOrvS7dBSx0N
 =f4c3
 -----END PGP SIGNATURE-----

Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:
 "These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
  window management), and a new Renesas R8A7794 SoC device ID.

  Details:

  Resource management:
   - Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
   - Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
     Helgaas)

  MSI:
   - Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)

  Renesas R-Car host bridge driver:
   - Add R8A7794 support (Sergei Shtylyov)

  Miscellaneous:
   - Fix devfn for VPD access through function 0 (Alex Williamson)
   - Use function 0 VPD only for identical functions (Alex Williamson)"

* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: rcar: Add R8A7794 support
  PCI: Use function 0 VPD for identical functions, regular VPD for others
  PCI: Fix devfn for VPD access through function 0
  PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
  PCI: Clear IORESOURCE_UNSET when clipping a bridge window
  PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
2015-09-25 11:16:53 -07:00