A host device that supports write protection should refuse to write to
an SD card that is designated read-only when write-protect is set. This
is an optional feature of the SD specification.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix SD card remove/insert detection by adding the correct card-detect
pin. All IGEP OMAP3 based boards use the same card-detect pin.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch explicitly enables the fixes for the below errata applicable
for AM43x Socs as was done for OMAP4.
754322: Faulty MMU translations following ASID switch
775420: A data cache maintenance operation which aborts,
followed by an ISB, without any DSB in-between,
might lead to deadlock
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Palmas Regulator is an exception and does not follow the standard
"vin-supply" common definitions for all regulators, as a result of this,
the input supplies are not reported to regulator framework, with the
obvious result of not being appropriately mapped. Fix the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dma channel information to the gpmc.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch disable mmc nodes by default in the dm814x.dtsi and
enable only when needed on a given dts
v2: Disable un-used mmc nodes on the related boards dts files
instead of from the included SOC dts
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will clean-up warnings at boot, since either that or cd-gpio{,s} are
mandated by the dts specification
of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@47810000[0]'
of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@47810000[0]'
v2: use the generic non-removable instead of ti,non-removable
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The padconf register WAKEUP_EN is now handled in a generic way using
Linux wakeirqs where pinctrl-single toggles the WAKEUP_EN bit when
a wakeirq is enabled or disabled.
At least omap5 gets confused if the WAKEUP_EN bit is set and the pin
is not claimed as a wakeirq. The end result is that wakeirqs don't
work properly as there is nothing handling the wakeirq.
So let's just remove the WAKEUP_EN usage from dts files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Playing audio works on omap5-uevm, but produces an "Unhandled fault:
imprecise external abort (0x1406) at 0x00000000" error on igepv5.
Looks like the twl6040 audpwron GPIO pin is different for these
boards. Let's fix the issue by configuring the audpwron in the
board specific dts file.
Cc: Agustí Fontquerni <af@iseebcn.com>
Cc: Eduard Gavin <egavin@iseebcn.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujflausi@ti com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Note: the configuration for the workaround needs to be done with
each CPU bringup, since CPU0 bringup is done by bootloader, it is
recommended to have the workaround in the bootloader, kernel also does
ensure that CPU0 has the workaround and makes the workaround active
when CPU1 gets active.
With CONFIG_SMP disabled, it is expected to be done by the bootloader.
This does show significant degradation in synthetic tests such as
mbw (https://packages.qa.debian.org/m/mbw.html)
mbw -n 100 100|grep AVG (on a test platform)
Without enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13406 MiB: 100.00000 Copy: 745.913 MiB/s
AVG Method: DUMB Elapsed: 0.06746 MiB: 100.00000 Copy: 1482.357 MiB/s
AVG Method: MCBLOCK Elapsed: 0.03058 MiB: 100.00000 Copy: 3270.569 MiB/s
After enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13757 MiB: 100.00000 Copy: 726.913 MiB/s
AVG Method: DUMB Elapsed: 0.12024 MiB: 100.00000 Copy: 831.668 MiB/s
AVG Method: MCBLOCK Elapsed: 0.09243 MiB: 100.00000 Copy: 1081.942 MiB/s
Most benchmarks are designed for specific performance analysis, so
overall usecase must be considered before making a decision to
enable/disable the erratum workaround.
Pending internal investigation, the erratum is kept disabled by default.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXM0NyAAoJEAf03oE53VmQ0IwIAI05Acjbko78+Hm/kWHlbJrx
5BLpJqTGLavbjbPjFnElKTr1c8m7Bgd6HNcat/2z9ZNh8/82FXyGOjYSp4W0BE9V
ovyD/lz/2fZyom4YLJjdCnVkwIV1pKHS+uNxy5zXMY2gJfz4VRtUh54H3ArdaQOE
LOKvrVl9bGorLbzbTpH0rSeKqQ1XFGPDlp1A3GUtI6646RWd5Eqe6zDzgQUwWJis
AR+sAcsqVb+IWY5rZwMyL0oZ1kjnEw4tihDTy+G+eBXRdRMYqSgEt8dBz65T3VYi
5EFXLuLjknnf3qVaxEU+og6kiJkefTYdB4I7xVR+dKbcILBSSqdHxlG1HmNkBQ4=
=CF/9
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "Second AT91 fix PR for 4.6" from Nicolas Ferre:
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
Device tree update for the Applied micro processor 460ex on-chip SATA to use
"dmas" property.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
copy_thread should not be enforcing 16 byte aligment and returning
-EINVAL. Other architectures trap misaligned stack access with SIGBUS
so arm64 should follow this convention, so remove the strict enforcement
check.
For example, currently clone(2) fails with -EINVAL when passing
a misaligned stack and this gives little clue to what is wrong. Instead,
it is arguable that a SIGBUS on the fist access to a misaligned stack
allows one to figure out that it is a misaligned stack issue rather
than trying to figure out why an unconventional (and undocumented)
-EINVAL is being returned.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, the PT driver always sets the PMI bit one region (page) before
the STOP region so that we can wake up the consumer before we run out of
room in the buffer and have to disable the event. However, we also need
an interrupt in the last output region, so that we actually get to disable
the event (if no more room from new data is available at that point),
otherwise hardware just quietly refuses to start, but the event is
scheduled in and we end up losing trace data till the event gets removed.
For a cpu-wide event it is even worse since there may not be any
re-scheduling at all and no chance for the ring buffer code to notice
that its buffer is filled up and the event needs to be disabled (so that
the consumer can re-enable it when it finishes reading the data out). In
other words, all the trace data will be lost after the buffer gets filled
up.
This patch makes PT also generate a PMI when the last output region is
full.
Reported-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1462886313-13660-2-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Intel Cherrytrail is based on Airmont core so MSR_FSB_FREQ[2:0] = 4
means that the CPU reference clock runs at 80MHz. Add this missing
frequency to the table.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Link: http://lkml.kernel.org/r/87y47gty89.fsf@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Similar to preadv and pwritev, preadv2 and pwritev2 need compat entries
in the 32-bit syscall table.
This bug was found by strace test suite.
Fixes: 4babf2c5ef ("x86: wire up preadv2 and pwritev2")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20160511084817.GA29823@altlinux.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Before commit 3e68dc57 "powerpc/powernv: Remove DMA32 PE list", NPU PEs
were linked to the NPU PHB via phb->ioda.pe_dma_list; after that fix,
the phb->ioda.pe_list is used.
During the pe_dma_list removal, list_add_tail(&phb->ioda.pe_dma_list)
was removed, however no list_add() was added so does this patch.
Fixes: 3e68dc57219a ("powerpc/powernv: Remove DMA32 PE list")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_pci_init_ioda_phb() helper allocates a blob to store auxilary
data such PE and M32/M64 segment allocation maps; this single blob has
few partitions, size of each is derived from the PE number -
phb->ioda.total_pe_num.
It was assumed that the minimum PE number is 8, however it is 4 for NPU
so the pe_alloc part was missing in the allocated blob. It was invisible
till recently as we were not tracking used M64 segments and NPUs do not
use M32 segments so the phb->ioda.m32_segmap (which was pointing to the
same address as phb->ioda.pe_alloc) has never been written to leaving
the pe_alloc memory intact.
After commit 401203ac2d "powerpc/powernv: Track M64 segment consumption"
the pe_alloc gets corrupted and PE allocation cannot work. This fixes
the issue by enforcing the minimum PE number to 8.
Fixes: 401203ac2d15 ("powerpc/powernv: Track M64 segment consumption")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
changed the pci_dn struct by removing its EEH-related members.
As part of this clean-up, DDW mechanism was modified to read the device
configuration address from eeh_dev struct.
As a consequence, now if we disable EEH mechanism on kernel command-line
for example, the DDW mechanism will fail, generating a kernel oops by
dereferencing a NULL pointer (which turns to be the eeh_dev pointer).
This patch just changes the configuration address calculation on DDW
functions to a manual calculation based on pci_dn members instead of
using eeh_dev-based address.
No functional changes were made. This was tested on pSeries, both
in PHyp and qemu guest.
Fixes: 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
Cc: stable@vger.kernel.org # v3.4+
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The label "reset" in eeh_pe_change_owner() is used only for once.
No need to keep it and just drop it. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none. In
both cases, the handlers triggered by eeh_report_reset() and
eeh_report_resume() shouldn't be called.
This ignores the error handlers from eeh_report_reset() and
eeh_report_resume().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org #v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org #v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit c8ceacc22b.
Gavin says: I missed the fact that it affects the PCI passthrou path as
reported by Alexey: When passing GPU (0003:01:00.0) which seats behind
the root port, the reset request is routed to skiboot in original code.
In skiboot, the link bouncing events are masked during the reset. So we
don't see EEH (freeze all) error even link bouncing happens. With the
changes included, the reset is done by kernel and the link bouncing
events aren't masked by altering content of PHB3 (or P7IOC) specific
hardware registers which are invisible to kernel (skiboot hides the
hardware specific). It means the link bouncing is seen by the root port
and it causes a EEH (freeze all) error. The PCI passthrough on GPU
device cannot work.
Requested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Requested-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the PT driver always sets the PMI bit one region (page) before
the STOP region so that we can wake up the consumer before we run out of
room in the buffer and have to disable the event. However, we also need
an interrupt in the last output region, so that we actually get to disable
the event (if no more room from new data is available at that point),
otherwise hardware just quietly refuses to start, but the event is
scheduled in and we end up losing trace data till the event gets removed.
For a cpu-wide event it is even worse since there may not be any
re-scheduling at all and no chance for the ring buffer code to notice
that its buffer is filled up and the event needs to be disabled (so that
the consumer can re-enable it when it finishes reading the data out). In
other words, all the trace data will be lost after the buffer gets filled
up.
This patch makes PT also generate a PMI when the last output region is
full.
Reported-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1462886313-13660-2-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jim reported:
UBSAN: Undefined behaviour in arch/x86/events/intel/core.c:3708:12
shift exponent 35 is too large for 32-bit type 'long unsigned int'
The use of 'unsigned long' type obviously is not correct here, make it
'unsigned long long' instead.
Reported-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Imre Palik <imrep@amazon.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 2c33645d36 ("perf/x86: Honor the architectural performance monitoring version")
Link: http://lkml.kernel.org/r/1462974711-10037-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We compute 'delta' and properly sign extend it and then ignore it and
recompute the raw value, loosing the sign extention.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Cc: linux-kernel@vger.kernel.org
Cc: luto@kernel.org
Cc: ray.huang@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new CPUID leaf to hold the contents of CPUID 0x80000007_EBX (RasCap).
Define bits that are currently in use:
Bit 0: McaOverflowRecov
Bit 1: SUCCOR
Bit 3: ScalableMca
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Shorten comment. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Do the !SMCA work first and then save us an indentation level for the
SMCA code.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Disable Deferred Error logging in MCA_{STATUS,ADDR} additionally for
SMCA systems as this information will retrieved from MCA_DE{STAT,ADDR}
on those systems.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Simplify, drop SMCA_MCAX_EN_OFF define too. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Scalable MCA provides new registers for all banks for logging deferred
errors: MCA_DESTAT and MCA_DEADDR. Deferred errors are always logged to
these registers.
Update the AMD deferred error handler to use these registers, if
available.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Sanity-check __log_error() args, massage a bit. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit c9a5eccac1 ("kvm/eventfd: add arch-specific set_irq",
2015-10-16) added the possibility for architecture-specific code
to handle the generation of virtual interrupts in atomic context
where possible, without having to schedule a work function.
Since we can easily generate virtual interrupts on XICS without
having to do anything worse than take a spinlock, we define a
kvm_arch_set_irq_inatomic() for XICS. We also remove kvm_set_msi()
since it is not used any more.
The one slightly tricky thing is that with the new interface, we
don't get told whether the interrupt is an MSI (or other edge
sensitive interrupt) vs. level-sensitive. The difference as far
as interrupt generation is concerned is that for LSIs we have to
set the asserted flag so it will continue to fire until it is
explicitly cleared.
In fact the XICS code gets told which interrupts are LSIs by userspace
when it configures the interrupt via the KVM_DEV_XICS_GRP_SOURCES
attribute group on the XICS device. To store this information, we add
a new "lsi" field to struct ics_irq_state. With that we can also do a
better job of returning accurate values when reading the attribute
group.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we don't support a mechanism for bypassing IRQs, don't register as
a consumer. This eliminates meaningless dev_info()s when the connect
fails between producer and consumer, such as on AMD systems where
kvm_x86_ops->update_pi_irte is not implemented
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.
This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.
The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.
This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reworks our stage 2 page table handling to have page table manipulation
macros separate from those of the host systems as the underlying
hardware page tables can be configured to be noticably different in
layout from the stage 1 page tables used by the host.
Adds 16K page size support based on the above.
Adds a generic firmware probing layer for the timer and GIC so that KVM
initializes using the same logic based on both ACPI and FDT.
Finally adds support for hardware updating of the access flag.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXMzKGAAoJEEtpOizt6ddyQ0AH/RS1tn3obEnujzD1yFeiSNS7
kBTwDEDdsAE7RJ12c43knfGaO4JO9+V2o1F5/16+/mjWDUJwAsm0yzSxvlxiS/+o
Q3QIfAbXxj/xia+sDFEtuSpRLL7Kl9oYeKBc5BijobvIQ5PKWm41kxehS8phMovQ
hiC2WQ5Wm1ww9L6AcI3gf8jqj4GJ/v+RSWzMTmPA7Wm7l03VGFn+G6AOnO0Rx6Fp
aRhI3dgvMAeMV8DXKTCdZggPrZ/ipLU+LgU+FwUXx2Ru9VfjU94MBEJG3FsTjNM0
UT1NLQ3kZaiYjlW/tN8WCXQDK1AUFDWUCHW7p77mq9w3cSylQBUlKbjRzTtjBsM=
=8PZF
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for Linux v4.7
Reworks our stage 2 page table handling to have page table manipulation
macros separate from those of the host systems as the underlying
hardware page tables can be configured to be noticably different in
layout from the stage 1 page tables used by the host.
Adds 16K page size support based on the above.
Adds a generic firmware probing layer for the timer and GIC so that KVM
initializes using the same logic based on both ACPI and FDT.
Finally adds support for hardware updating of the access flag.
The x86 exception table sorting was changed in commit 29934b0fb8
("x86/extable: use generic search and sort routines") to use the arch
independent code in lib/extable.c. However, the patch was mangled
somehow on its way into the kernel from the last version posted at [1].
The committed version kind of attempted to incorporate the changes of
commit 548acf1923 ("x86/mm: Expand the exception table logic to allow
new handling options") as in _completely_ _ignoring_ the x86 specific
'handler' member of struct exception_table_entry. This effectively
broke the sorting as entries will only partly be swapped now.
Fortunately, the x86 Kconfig selects BUILDTIME_EXTABLE_SORT, so the
exception table doesn't need to be sorted at runtime. However, in case
that ever changes, we better not break the exception table sorting just
because of that.
[ Ard Biesheuvel points out that BUILDTIME_EXTABLE_SORT applies to the
core image only, but we still rely on the sorting routines for modules
in that case - Linus ]
Fix this by providing a swap_ex_entry_fixup() macro that takes care of
the 'handler' member.
[1] https://lkml.org/lkml/2016/1/27/232
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Fixes: 29934b0fb8 ("x86/extable: use generic search and sort routines")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
an objtool warning for CONFIG_PROFILE_ALL_BRANCHES.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXM0h+AAoJEL/70l94x66DhjwH/2l24ouNC32DJGoY511yWogF
QrBrmQnnT1r+v9IDCC5ITCCkJp+EPF0uFwLI+T6URzRdSdNUN/EqYymUyhsICWwb
9xIsR9VraeB4OhH5IMps1Pkwyx6FMjeVqvVx8dib+NUQpV2o5KxkkFsE9oIX7mtA
PgwRaLsV8MFZH06g/qvwYPs5NNUecQU8AFCAps0PzWSXG6KHmzsjJZjsXbDhb3n4
oOGJTLXlRS+SSOWFjngYJNIQ7Z8V1WHM6qftZXtcDWIFbq8CuWn9dZR2WhpUu+nK
J/I5WC99stxgljFOjI/zdPKQbRy0eBQyDAPHAblDo83vSKsDRgYGX3608gGz3xY=
=s75+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two small x86 patches, improving "make kvmconfig" and fixing an
objtool warning for CONFIG_PROFILE_ALL_BRANCHES"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvmconfig: add more virtio drivers
x86/kvm: Add stack frame dependency to fastop() inline asm
The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.
This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3be ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit 94ea9c7a579f ("lib, switch CONFIG_PRINTK_TIME to int") changes
the type of CONFIG_PRINTK_TIME and adapts all existing defconfig files,
while we add two new defconfig files with d0bc3483da ("arm/configs:
Add Aspeed defconfig"), with the old type.
This changes the two new defconfig files to match the other ones.
As a result, we get harmless warnings for the arm-soc defconfig
branch by itself, but everything will work when 4.7-rc1 is out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
IBM POWER8 NVlink systems come with Tesla K40-ish GPUs each of which
also has a couple of fast speed links (NVLink). The interface to links
is exposed as an emulated PCI bridge which is included into the same
IOMMU group as the corresponding GPU.
In the kernel, NPUs get a separate PHB of the PNV_PHB_NPU type and a PE
which behave pretty much as the standard IODA2 PHB except NPU PHB has
just a single TVE in the hardware which means it can have either
32bit window or 64bit window or DMA bypass but never two of these.
In order to make these links work when GPU is passed to the guest,
these bridges need to be passed as well; otherwise performance will
degrade.
This implements and exports API to manage NPU state in regard to VFIO;
it replicates iommu_table_group_ops.
This defines a new pnv_pci_ioda2_npu_ops which is assigned to
the IODA2 bridge if there are NPUs for a GPU on the bridge.
The new callbacks call the default IODA2 callbacks plus new NPU API.
This adds a gpe_table_group_to_npe() helper to find NPU PE for the IODA2
table_group, it is not expected to fail as the helper is only called
from the pnv_pci_ioda2_npu_ops.
This does not define NPU-specific .release_ownership() so after
VFIO is finished, DMA on NPU is disabled which is ok as the nvidia
driver sets DMA mask when probing which enable 32 or 64bit DMA on NPU.
This adds a pnv_pci_npu_setup_iommu() helper which adds NPUs to
the GPU group if any found. The helper uses helpers to look for
the "ibm,gpu" property in the device tree which is a phandle of
the corresponding GPU.
This adds an additional loop over PEs in pnv_ioda_setup_dma() as the main
loop skips NPU PEs as they do not have 32bit DMA segments.
As pnv_npu_set_window() and pnv_npu_unset_window() are started being used
by the new IODA2-NPU IOMMU group, this makes the helpers public and
adds the DMA window number parameter.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
[mpe: Add pnv_pci_ioda_setup_iommu_api() to fix build with IOMMU_API=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_ioda_pe struct keeps an array of peers. At the moment it is only
used to link GPU and NPU for 2 purposes:
1. Access NPU quickly when configuring DMA for GPU - this was addressed
in the previos patch by removing use of it as DMA setup is not what
the kernel would constantly do.
2. Invalidate TCE cache for NPU when it is invalidated for GPU.
GPU and NPU are in different PE. There is already a mechanism to
attach multiple iommu_table_group to the same iommu_table (used for VFIO),
we can reuse it here so does this patch.
This gets rid of peers[] array and PNV_IODA_PE_PEER flag as they are
not needed anymore.
While we are here, add TCE cache invalidation after enabling bypass.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>