Add support for the ARM SP805 Watchdog timer to the Northstar Plus
device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM SP804 timer to the Northstar Plus device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM Performance Monitor Unit to the Northstar Plus
device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is a double definition of the CPUs present in the device tree.
Remove unnecessary cpu device tree definition.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding the ranges value is preventing the PCI nodes from working.
Pulling them out outside makes them work again (and makes it similar to
the NS2 device tree).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch enables PCIe0 and PCIe4 for NS2 by adding
appropriate DT nodes in NS2 DT.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have one ARM SP805 watchdog instance on NS2 for non-secure software
hence this patch adds appropriate watchdog DT node in NS2 DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have four ARM SP804 dual-mode timer instances in NS2 SoC
hence this patch adds appropriate DT nodes for NS2.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The IPROC SDHCI driver works fine for SDIO 3.0 on NS2 so let's enable
it for NS2 SoC in NS2 DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We select COMMON_CLK_IPROC, PINCTRL, and GPIOLIB in arm64 Kconfig
for ARCH_BCM_IPROC so that we can use COMMON_CLK, PINCTRL and GPIOLIB
with iProc SoC drivers.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
OMAP5 has 3 thermal zones cpu, core and multimedia.
On the other hand DRA7 has 5 thermal zones cpu, gpu, core, dspeve
and iva. Currently cpu, core and multimedia are being added via device tree
and the other 2 are getting added via kernel. Add the missing thermal
domains in device tree so we can create the zones with the appropriate
trip numbers, type and temperatures.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes a dtsi file to contain the thermal data
for IVA domain. This data will enable a thermal shutdown at 125C.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes a dtsi file to contain the thermal data
for DSPEVE domain. This data will enable a thermal shutdown at 125C.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DWC3's tx-fifo-resize property has been deprecated
because of it being unnecessary to any HW other than
OMAP5 ES1.0.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds an idle pinctrl state, which will be used
by the driver to avoid incoming data during clock
rate changes or data flushing.
Signed-off-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MCLK is provided by an external clock of 24.576MHz.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART0 device is the device to be used for boot console output.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide RESET GPIO for the USB PHY, the USB Host port mode and
the PHY device for the controller. Also provides pin multiplexer
information for USB host pins.
Signed-off-by: Pau Pajuel <ppajuel@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 device is the device to be used for boot console output.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch defines the pin muxing to configure the hsusb0 through
the twl4030 PMIC, because we can't always assume the bootloader will
do it correctly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds the modem to the SSI port.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds all necessary information
to initialize the SSI module, but does not yet add the
modem information.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devkit has an AT25 EEPROM on MCSPI1. Enable this with default
parameters.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulator and fix pin muxing to allow Panel to sleep and
wake from sleep for some low power improvements.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Wireless version of the SOM uses an AT24 EEPROM to store product ID.
The EEPROM is readonly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Logic PD Torpedo standard kits come with a SOM populated to us an
8-bit parallel camera interface. This patch pin muxes the omap3-isp
pins, sets the MT9P031 clicks, and configures the i2c2 bus to communicate
with the mt9p031 on address 0x48.
I have not done a lot of testing, but when modprobing
mt9p031, then omap3-isp, the board responds with
MT9P031 detected at address 0x48.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.
Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.
Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge fixes from Andrew Morton:
"10 fixes"
The lockdep hlist conversion is in the locking tree too, waiting for the
next merge window. Andrew thought it should go in now. I'll take it,
since it fixes a real problem and looks trivially correct (famous last
words).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/x86/Kconfig: CONFIG_X86_UV should depend on CONFIG_EFI
mm: fix pfn_t vs highmem
kernel/locking/lockdep.c: convert hash tables to hlists
mm,thp: fix spellos in describing __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
mm,thp: khugepaged: call pte flush at the time of collapse
mm/backing-dev.c: fix error path in wb_init()
mm, dax: check for pmd_none() after split_huge_pmd()
vsprintf: kptr_restrict is okay in IRQ when 2
mm: fix filemap.c kernel doc warning
ubsan: cosmetic fix to Kconfig text
* fix omap2plus_defconfig to enable omapfb as it was in v4.4
* ocfb: fix timings for margins
* s6e8ax0, da8xx-fb: fix compile warnings
* mmp: fix build failure caused by bad printk parameters
* imxfb: fix clock issue which kept the display off
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kfw6
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fix omap2plus_defconfig to enable omapfb as it was in v4.4
- ocfb: fix timings for margins
- s6e8ax0, da8xx-fb: fix compile warnings
- mmp: fix build failure caused by bad printk parameters
- imxfb: fix clock issue which kept the display off
* tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: fbdev: imxfb: Provide a reset mechanism
fbdev: mmp: print IRQ resource using %pR format string
fbdev: da8xx-fb: remove incorrect type cast
fbdev: s6e8ax0: avoid unused function warnings
ocfb: fix tgdel and tvdel timing parameters
ARM: omap2plus_defconfig: update display configs
If a driver PM runtime is disabled via sysfs, and the module is
unloaded, PM runtime can't do anything to disable the device. Let's
let the interconnect disable the device on BUS_NOTIFY_UNBOUND_DRIVER.
Otherwise omap_device will produce and error on the following module
reload. This can be easily tested with something like:
# modprobe omap_hsmmc
# echo on > /sys/devices/platform/68000000.ocp/4809c000.mmc/power/control
# rmmod omap_hsmmc
# modprobe omap_hsmmc
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers using pm_runtime_use_autosuspend() may not get disabled after
-EPROBE_DEFER. On the following device driver probe, hardware state
is different from the PM runtime state causing omap_device to produce
the following error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
Let's add a proper error message so driver writers can easily fix
their drivers for PM.
In general, the solution is to fix the drivers to follow the PM
runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Let's not return with 0 from _od_runtime_resume() as that will
eventually lead into new drivers with broken PM runtime that will
block deeper idle states on omaps.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit adds the Device Tree description for the 1GB NAND flash
present in the Armada 370 DB and Armada XP DB evaluation boards from
Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Switching between stacks is only valid if we are tracing ourselves while on the
irq_stack, so it is only valid when in current and non-preemptible context,
otherwise is is just zeroed off.
Fixes: 132cd887b5 ("arm64: Modify stack trace and dump for use with irq_stack")
Acked-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
MMUv4 supports 2 concurrent page sizes: Normal and Super [4K to 16M]
So far Linux supported a single super page size for a given Normal page,
depending on the software page walking address split.
e.g. we had 11:8:13 address split for 8K page, which meant super page
was 2 ^(8+13) = 2M (given that THP size has to be PMD_SHIFT)
Now we turn this around, by allowing multiple Super Pages in Kconfig
(currently 2M and 16M only) and forcing page walker address split to
PGDIR_SHIFT and PAGE_SHIFT
For configs without Super page, things are same as before and
PGDIR_SHIFT can be hacked to get non default address split
The motivation for this change is a customer who needs 16M super page
and a 8K Normal page combo.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arch/x86/built-in.o: In function `uv_bios_call':
(.text+0xeba00): undefined reference to `efi_call'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent versions of libfdt add a dependency on strnlen. Copy the
implementation in lib/string.c here, so we can update libfdt.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
This enables the GPIO-a support for Broadcom NSP SoC
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When rodata is large enough that it crosses a section boundary after the
kernel text, mark the rest NX. This is as close to full NX of rodata as
we can get without splitting page tables or doing section alignment via
CONFIG_DEBUG_ALIGN_RODATA.
When the config is:
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_ALIGN_RODATA is not set
Before:
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80a00000 9M ro x SHD
0x80a00000-0xa0000000 502M RW NX SHD
After:
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80700000 6M ro x SHD
0x80700000-0x80a00000 3M ro NX SHD
0x80a00000-0xa0000000 502M RW NX SHD
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For an XIP build, _etext does not represent the end of the
binary image that needs to stay mapped into the MODULES_VADDR area.
Years ago, data came before text in the memory map. However,
now that the order is text/init/data, an XIP_KERNEL needs to map
up to the data location in order to keep from cutting off
parts of the kernel that are needed.
We only map up to the beginning of data because data has already been
copied, so there's no reason to keep it around anymore.
A new symbol is created to make it clear what it is we are referring
to.
This fixes the bug where you might lose the end of your kernel area
after page table setup is complete.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b9b32bf70f ("ARM: use linker magic for vectors and vector stubs")
updated the linker script to emit the .vectors and .stubs sections into a
VMA range that is zero based and disjoint from the normal static kernel
region. The reason for that was that this way, the sections can be placed
exactly 4 KB apart, while the payload of the .vectors section is only 32
bytes.
Since the symbols that are part of the .stubs section are emitted into the
kallsyms table, they appear with zero based addresses as well, e.g.,
00001004 t vector_rst
00001020 t vector_irq
000010a0 t vector_dabt
00001120 t vector_pabt
000011a0 t vector_und
00001220 t vector_addrexcptn
00001240 t vector_fiq
00001240 T vector_fiq_offset
As this confuses perf when it accesses the kallsyms tables, commit
7122c3e915 ("scripts/link-vmlinux.sh: only filter kernel symbols for
arm") implemented a somewhat ugly special case for ARM, where the value
of CONFIG_PAGE_OFFSET is passed to scripts/kallsyms, and symbols whose
addresses are below it are filtered out. Note that this special case only
applies to CONFIG_XIP_KERNEL=n, not because the issue the patch addresses
exists only in that case, but because finding a limit below which to apply
the filtering is not entirely straightforward.
Since the .vectors and .stubs sections contain position independent code
that is never executed in place, we can emit it at its most likely runtime
VMA (for more recent CPUs), which is 0xffff0000 for the vector table and
0xffff1000 for the stubs. Not only does this fix the perf issue with
kallsyms, allowing us to drop the special case in scripts/kallsyms
entirely, it also gives debuggers a more realistic view of the address
space, and setting breakpoints or single stepping through code in the
vector table or the stubs is more likely to work as expected on CPUs that
use a high vector address. E.g.,
00001240 A vector_fiq_offset
...
c0c35000 T __init_begin
c0c35000 T __vectors_start
c0c35020 T __stubs_start
c0c35020 T __vectors_end
c0c352e0 T _sinittext
c0c352e0 T __stubs_end
...
ffff1004 t vector_rst
ffff1020 t vector_irq
ffff10a0 t vector_dabt
ffff1120 t vector_pabt
ffff11a0 t vector_und
ffff1220 t vector_addrexcptn
ffff1240 T vector_fiq
(Note that vector_fiq_offset is now an absolute symbol, which kallsyms
already ignores by default)
The LMA footprint is identical with or without this change, only the VMAs
are different:
Before:
Idx Name Size VMA LMA File off Algn
...
14 .notes 00000024 c0c34020 c0c34020 00a34020 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
15 .vectors 00000020 00000000 c0c35000 00a40000 2**1
CONTENTS, ALLOC, LOAD, READONLY, CODE
16 .stubs 000002c0 00001000 c0c35020 00a41000 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
17 .init.text 0006b1b8 c0c352e0 c0c352e0 00a452e0 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
After:
Idx Name Size VMA LMA File off Algn
...
14 .notes 00000024 c0c34020 c0c34020 00a34020 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
15 .vectors 00000020 ffff0000 c0c35000 00a40000 2**1
CONTENTS, ALLOC, LOAD, READONLY, CODE
16 .stubs 000002c0 ffff1000 c0c35020 00a41000 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
17 .init.text 0006b1b8 c0c352e0 c0c352e0 00a452e0 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b9b32bf70f ("ARM: use linker magic for vectors and vector stubs")
introduced new global definitions of __vectors_start and __stubs_start,
and changed the existing ones to have internal linkage only. However, these
symbols are still visible to kallsyms, and due to the way the .vectors and
.stubs sections are emitted at the base of the VMA space, these duplicate
definitions have conflicting values.
$ nm -n vmlinux |grep -E __vectors|__stubs
00000000 t __vectors_start
00001000 t __stubs_start
c0e77000 T __vectors_start
c0e77020 T __stubs_start
This is completely harmless by itself, since the wrong values are local
symbols that cannot be referenced by other object files directly. However,
since these symbols are also listed in the kallsyms symbol table in some
cases (i.e., CONFIG_KALLSYMS_ALL=y and CONFIG_XIP_KERNEL=y), having these
conflicting values can be confusing. So either remove them, or make them
strictly local.
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>