The PCIe controller is found on all Juno SoC version. However it's not
functional on R0 due to some hardware bug.
In preparation to add Juno R2 support, this patch moves the
pcie-controller defination to base DTS file. It's marked as disabled by
default and is enabled for Juno R1 explicitly.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The ARMv8 Foundation model sports a command line parameter to use
a GICv3 emulation instead of the default GICv2 interrupt controller.
Add a new .dts file which reuses most of the definitions of the
existing model while just adding the required properties for the
GICv3 node.
This allows the public Foundation model to run with a GICv3.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The ARMv8 Foundation model can be run with a GICv2 or a GICv3.
To prepare for the GICv3 version of the .dts without code duplication,
move most of the nodes of the existing DT (except the GIC) into an
include file and just keep that include statement and the GIC node in
the current foundation-v8.dts.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Foundation model GIC mapping is wrong, as the GICC region should
be 8kB instead of 4kB (the model implements the GICv2 architecture).
This defect prevents the driver from switching to EOImode==1.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
To prepare the ARM foundation model to support GICv3, we adjust
the #address-cells property of the current GICv2 node to be
compatible with the two cells required for GICv3 later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Before this, we issued this message from save_microcode_in_initrd()
which is called from free_initrd_mem(), i.e., only when we have an
initrd enabled. However, we can update from builtin microcode too but
then we don't issue the update message.
Fix it by issuing that message on the generic driver init path.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-17-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rename it to mc_tmp_ptrs to denote better what it is - a temporary array
for saving pointers to microcode blobs. And "initrd" is not accurate
anymore since initrd is not the only source for early microcode.
Therefore, rename copy_initrd_ptrs() to copy_ptrs() simply and
"initrd_start" to "offset".
And then do the following convention: the global variable is called
"mc_tmp_ptrs" and the local function arguments "mc_ptrs" for
differentiation.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-14-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... and drop the 32-bit casting games which we had to do at the time
because wrmsr() was unforgiving then, see c3fd0bd5e19a from the
full history tree:
commit c3fd0bd5e19aaff9cdd104edff136a2023db657e
Author: Linus Torvalds <torvalds@home.osdl.org>
Date: Tue Feb 17 23:23:41 2004 -0800
Fix up the microcode update on regular 32-bit x86. Our wrmsr()
is a bit unforgiving and really doesn't like 64-bit values.
...
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-13-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Get rid of local variable cpu_num as it is equal to @cpu now. Deref
cpu_data() only when it is really needed at the end.
No functionality change.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-12-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If we're going to BUG_ON() because we're running on the wrong CPU, we
better do it as the first thing we do when entering that function. And
also, turn it into a WARN_ON() because it is not worth to panic the
system if we apply the microcode on the wrong CPU - we're simply going
to exit early.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-11-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Well, it is apparent what it points to - microcode. And since it is the
intel loader, no need for the "_intel" suffix. Use "!" for the 0/NULL
checks, while at it.
No functionality change.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-10-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is shorter and easier on the eyes. Change the "== 0" tests to "!..."
while at it.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So it is always a head-twister when trying to stare at code which has a
bunch of
struct mc_saved_data *mc_saved_data;
local function variables *and* a global mc_saved_data of the same name.
Rename all locals to "mcs" to differentiate from the global one.
No functionality change.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-8-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is especially annoying on large boxes:
x86: Booting SMP configuration:
.... node #0, CPUs: #1
microcode: CPU1 microcode updated early to revision 0x428, date = 2014-05-29
#2
microcode: CPU2 microcode updated early to revision 0x428, date = 2014-05-29
#3
...
so issue the update message only once.
$ grep microcode /proc/cpuinfo
shows whether every core got updated properly.
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We do parse for the disable microcode loader chicken bit very early.
After the driver merge, the __setup() param parsing method is not needed
anymore so get rid of it.
In addition, fix a compiler warning from an old SLES11 gcc (4.3.4)
reported by Jan Beulich <jbeulich@suse.com>:
arch/x86/kernel/cpu/microcode/core.c: In function ‘load_ucode_bsp’:
arch/x86/kernel/cpu/microcode/core.c:96: warning: array subscript is above array bounds
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Set the initrd @start depending on the presence of an initrd. Otherwise,
builtin microcode loading doesn't work as the start is wrong and we're
using it to compute offset to the microcode blobs.
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.4
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Voegtle reported that doing oldconfig with a .config which has
CONFIG_MICROCODE enabled but BLK_DEV_INITRD disabled prevents the
microcode loading mechanism from being built.
So untangle it from the BLK_DEV_INITRD dependency so that oldconfig
doesn't turn it off and add an explanatory text to its Kconfig help what
the supported methods for supplying microcode are.
Reported-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.4
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454499225-21544-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add dts file to support Buffalo Linkstation LS-GL
(a.k.a Buffalo Linkstation Pro/Live), which is marvell orion5x based
3.5" HDD NAS.
Product info:
- (JPN) http://buffalo.jp/products/catalog/item/l/ls-gl/
- (ENG) http://www.buffalotech.com/products/network-storage/linkstation/linkstation-pro
This device tree is based on the board file:
arch/arm/mach-orion5x/kurobox_pro-setup.c
However, that board file also support Kurobox Pro, which is not supported by
device tree yet. So the board file is not removed.
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In order to support more linkstation devices, common part of current
.dts file goes into .dtsi file. Some .dtsi start with "mvebu-" prefix
because other kirkwood based linkstation devices are similar, and
will be migrated to use these .dtsi some time later.
- orion5x-linkstation.dtsi
- mvebu-linkstation-fan.dtsi
- mvebu-linkstation-gpio-simple.dtsi
while all rest part remains in device specific .dts file:
- orion5x-linkstation-lswtgl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds some comments to the Armada 385 AP Device Tree
description to indicate which Ethernet interface matches which
physical connector on the board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Armada 38x, the available network interfaces are:
- port 0, at 0x70000
- port 1, at 0x30000
- port 2, at 0x34000
Due to the rule saying that DT nodes should be ordered by register
addresses, the network interfaces are probed in this order:
- port 1, at 0x30000, which gets named eth0
- port 2, at 0x34000, which gets named eth1
- port 0, at 0x70000, which gets named eth2
(if all three ports are enabled at the board level)
Unfortunately, the network subsystem doesn't provide any way to rename
network interfaces from the kernel (it can only be done from
userspace). So, the default naming of the network interfaces is very
confusing as it doesn't match the datasheet, nor the naming of the
interfaces in the bootloader, nor the naming of the interfaces on
labels printed on the board.
For example, on the Armada 388 GP, the board has two ports, labelled
GE0 and GE1. One has to know that GE0 is eth1 and GE1 is eth0, which
isn't really obvious.
In order to solve this, this patch proposes to exceptionaly violate
the rule of "order DT nodes by register address", and put the 0x70000
node before the 0x30000 node, so that network interfaces get named in
a more natural way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MTD flash stores u-boot and u-boot environment on linkstation lswtgl.
The latter one can be easily read/write by u-boot-tools package in Debian.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the 'do' command to dump the OPAL msglog in xmon.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
[mpe: Reduce the amount of ifdefery required]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix audio on kirkwood-openrd-client:
1) The audio-controller was left disabled.
2) The probe fails because cs42l51 is missing #sound-dai-cells.
/sound/simple-audio-card,codec: could not get #sound-dai-cells for /ocp@f1000000/i2c@11000/cs42l51@4a
asoc-simple-card sound: parse error -22
asoc-simple-card: probe of sound failed with error -22
3) The mapping is incorrect:
asoc-simple-card sound: cs42l51-hifi <-> spdif mapping ok
should be:
asoc-simple-card sound: cs42l51-hifi <-> i2s mapping ok
Reported-by: Rick Thomas <rbthomas@pobox.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Rick Thomas <rbthomas@pobox.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Some OpenRD boards have RS-232 and RS-486 connectors wired, but using them
needs a custom DTB as the current DTB configures SD card slot instead.
This patch adds documentation into the DTS on how to change
the configuration.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
- LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
- There're two red LED indicator on LS-WVL to show when HDD fails,
which is similar to LS-WXL, but there's no such on LS-VL.
So after the split, common part goes into .dtsi file:
- kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
- kirkwood-linkstation-lsvl.dts
- kirkwood-linkstation-lswvl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
- There're two red LED indicator on LS-WXL to show when HDD fails,
but there's no such on LS-WSXL.
- There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.
So after the split, common part goes into .dtsi file:
- kirkwood-linkstation.dtsi
- kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
- kirkwood-linkstation-lswsxl.dts
- kirkwood-linkstation-lswxl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The SD card slot was enabled by default with legacy booting.
It does not work anymore with DT boot. Fix by providing GPIO configuration
that matches the old default.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The UART/SD pin names are swapped, fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the commit a526973e02 ("pinctrl: mvebu: Fix mapping of pin
63 (gpo -> gpio)"), the mpp63 is no more declared as a GPO but is a
GPIO. Even if in the datasheet this pin is described as GPO, the
experience of the D-Link DNS-327L board shows that it can be used as a
GPIO.
This commits generated warnings for the board using this pin as gpo, with
this patch the dts are fixed by using the new function (gpio) instead of
the old one.
The binding documentation has also been updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Using the usb-nop-xceiv PHY for the xhci nodes allows a better
representation of the hardware but also a better handling of the
regulator. By linking the regulator to the PHY there is no more need to
use the regulator-always-on property, then it allows a better power
management.
The remaining usb node uses the ehci-orion driver which can't be used
with the usb-nop-xceiv PHY and must keeps the direct link to the
regulator with the regulator-always-on property.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Really, what we meant by regulator-always-on is that the regulators
are already turned on by the bootloader, for which regulator-boot-on
is a better description.
A net advantage of using regulator-boot-on is that the regulator is
not touched at boot time by the kernel, which avoids having the hard
drives spinning down and then up again, taking several (~5) seconds of
additional boot time.
In addition, there is no need to have such properties on the child
regulators used for SATA. Having it on the parent regulator that
really controls the GPIO is sufficient.
Without the patch:
[ 3.945866] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.995862] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.005863] ata4: SATA link down (SStatus 0 SControl 300)
[ 9.125861] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 9.144575] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 9.151471] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
(and you can hear the disk spinning down and up during this 5.1
seconds delay)
With the patch:
[ 3.945988] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.005980] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.011404] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.145978] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.153701] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 4.160597] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As the name of the Device Tree file name suggests, the Armada 388 GP
really contains an Armada 388 SoC, so this commit updates the board
name and compatible string in the Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
It is not uncommon to boot a root filesystem from a USB
pendrive and similar, so enable USB mass storage, backed
by SCSI and SD block devices in the RealView defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The realview has two defconfigs: realview_defconfig and
realview-smp_defconfig. We now have working SMP_ON_UP so
make them equal so we can delete the -smp variant. For
some reason NO_HZ_FULL was missing from the plain
realview_defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the OPAL msglog/console buffer is exposed as a sysfs file, with
the sysfs read handler responsible for retrieving the log from the OPAL
buffer. We'd like to be able to use it in xmon as well.
Refactor the OPAL msglog code to create a new function, opal_msglog_copy(),
that copies to an arbitrary buffer. Separate the initialisation code into
generic memcons init and sysfs file creation.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>