Commit graph

127,691 commits

Author SHA1 Message Date
Javier Martinez Canillas
dbe2a40a12 ARM: dts: Remove broken-cd from eMMC node in exynos5800-peach-pi
The eMMC is non-removable so is marked with the non-removable DT
property to avoid having to redetect it after a suspend/resume.

But it also has the broken-cd property which is wrong since only
one of the DT properties for card detection should be used.

Also remove the card-detect-delay property that is not needed with
non-removable.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2015-12-29 09:07:10 +09:00
Javier Martinez Canillas
783482725f ARM: dts: Mark SDIO as non-removable in exynos5250-snow-common
The Exynos5250 Snow Chromebooks have a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.

This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:

[  181.944636] mmc2: error -2 during resume (card was removed?)

Also remove the card-detect-delay property that is not needed with
non-removable.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2015-12-29 09:07:09 +09:00
Javier Martinez Canillas
29a2289deb ARM: dts: Mark SDIO as non-removable in exynos5420-peach-pit
The Exynos5420 Peach Pit Chromebook has a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.

This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:

[  181.944636] mmc2: error -2 during resume (card was removed?)

Also remove the card-detect-delay property that is not needed with
non-removable.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2015-12-29 09:07:09 +09:00
Javier Martinez Canillas
3752216286 ARM: dts: Mark SDIO as non-removable in exynos5800-peach-pi
The Exynos5800 Peach Pi Chromebook has a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.

This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:

[  181.944636] mmc2: error -2 during resume (card was removed?)

Also remove the card-detect-delay property that is not needed with
non-removable.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2015-12-29 09:07:09 +09:00
Thomas Falcon
032c5e8284 Driver for IBM System i/p VNIC protocol
This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems.  The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.

This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-28 00:12:13 -05:00
Linus Torvalds
3ae86f1a9f Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:

 - Fix bitrot in __get_user_unaligned()
 - EVA userspace accessor bug fixes.
 - Fix for build issues with certain toolchains.
 - Fix build error for VDSO with particular toolchain versions.
 - Fix build error due to a variable that should have been removed by an
   earlier patch

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix bitrot in __get_user_unaligned()
  MIPS: Fix build error due to unused variables.
  MIPS: VDSO: Fix build error
  MIPS: CPS: drop .set mips64r2 directives
  MIPS: uaccess: Take EVA into account in [__]clear_user
  MIPS: uaccess: Take EVA into account in __copy_from_user()
  MIPS: uaccess: Fix strlen_user with EVA
2015-12-27 18:12:21 -08:00
Linus Torvalds
db0665012c ARM: SoC fixes for v4.4
A handful of fixes for OMAP, i.MX, Allwinner and Tegra:
 
 - A clock rate and a PHY setup fix for i.MX6Q/DL
 - A couple of fixes for the reduced serial bus (sunxi-rsb) on Allwinner
 - UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
 - Suspend fix for Tegra124 Chromebooks
 - Fix for missing implicit include that's different between ARM/ARM64
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWgDAQAAoJEIwa5zzehBx3muAP/RJD+oERDw/XiBSCl4k4kvTZ
 M4ep2ExO/GPXewKXyK7rlbNWMitBwttdT5OmXuuxT7BA/ODAGk90uvZSebIHRxkh
 bqnt+3njeR3M6FrTp6Np+yCh3I0hLYJoRInV3Vh8XQcml0LobIIq2BbdahIg/2JO
 sSDLAzJSR15CfnnKOSexvfRFoslLaKG0ffbxmR32HiMgnbq8ZfkRr7fANsrXTzoX
 oHxEV0uQXBY0d1TQ71rT/4KdTKN9QsdJI6xAjUGH95MYu+ZE0DEnW/wodd/f4e+p
 dyV+qoS2LHJnhYgJho3r19icM0iyNRm0Yt0GqP7ERN/y5GGa41slE9eThMG7WQ4h
 Ot5DEF2GmP7tSYhp4pqEeLqHnfou9+WzxxNP6wxGceqlg9EPuPRtzdCPStZYW4rD
 6+SQCvFs0vHZlEbbAfQLhRgDpvr9enGjCcWm6ntUcgwxFy0CPmRV9g5gIeipZOwi
 QfJM233tudUkDQxJYrCEgKxHy3a7T3K9LgYMM0VO1JRAEpaPIBmxZ0A+Y84WJbTE
 7r+r3eDC8RFF3bLbNRb/Ogt5OHOQUdElhRXcyz/BYA/X4HOT4wyVNM12aBlmW9uN
 aDB4HWE2lKV/h2pxWRR1Hem1NHYRUpcdVzkwRvncDHnxCAmb82BE2x1Ub3+fqa0v
 f0eO7GjUDRdPsQXn0zZn
 =kNRV
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "A smallish set of fixes that we've been sitting on for a while now,
  flushing the queue here so they go in.  Summary:

  A handful of fixes for OMAP, i.MX, Allwinner and Tegra:

   - A clock rate and a PHY setup fix for i.MX6Q/DL
   - A couple of fixes for the reduced serial bus (sunxi-rsb) on
     Allwinner
   - UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
   - Suspend fix for Tegra124 Chromebooks
   - Fix for missing implicit include that's different between
     ARM/ARM64"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
  bus: sunxi-rsb: Fix peripheral IC mapping runtime address
  bus: sunxi-rsb: Fix primary PMIC mapping hardware address
  ARM: dts: Fix UART wakeirq for omap4 duovero parlor
  ARM: OMAP2+: AM43xx: select ARM TWD timer
  ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
  fsl-ifc: add missing include on ARM64
  ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
  ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
  bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
  ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
2015-12-27 18:06:31 -08:00
Al Viro
930c0f708e MIPS: Fix bitrot in __get_user_unaligned()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-12-27 20:07:44 +01:00
Andrew Donnellan
dc3799bb9a powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
Fix off-by-one error in opal_mce_check_early_recovery() when checking
whether the NIP falls within OPAL space.

Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-12-27 19:12:41 +11:00
Andrew Donnellan
759fb100b2 powerpc: Fix style of self-test config prompts
A few of the config prompts for powerpc self-tests have periods at the
end, which is inconsistent with the rest of the prompts. Remove the
periods.

Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-12-27 19:12:40 +11:00
Michael Neuling
57a9039052 powerpc/powernv: Only delay opal_rtc_read() retry when necessary
Only delay opal_rtc_read() when busy and are going to retry.

This has the advantage of possibly saving a massive 10ms off booting!

Kudos to Stewart for noticing.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-12-27 19:12:40 +11:00
Russell Currey
affddff69c powerpc/powernv: Add a kmsg_dumper that flushes console output on panic
On BMC machines, console output is controlled by the OPAL firmware and is
only flushed when its pollers are called.  When the kernel is in a panic
state, it no longer calls these pollers and thus console output does not
completely flush, causing some output from the panic to be lost.

Output is only actually lost when the kernel is configured to not power off
or reboot after panic (i.e. CONFIG_PANIC_TIMEOUT is set to 0) since OPAL
flushes the console buffer as part of its power down routines.  Before this
patch, however, only partial output would be printed during the timeout wait.

This patch adds a new kmsg_dumper which gets called at panic time to ensure
panic output is not lost.  It accomplishes this by calling OPAL_CONSOLE_FLUSH
in the OPAL API, and if that is not available, the pollers are called enough
times to (hopefully) completely flush the buffer.

The flushing mechanism will only affect output printed at and before the
kmsg_dump call in kernel/panic.c:panic().  As such, the "end Kernel panic"
message may still be truncated as follows:

>Call Trace:
>[c000000f1f603b00] [c0000000008e9458] dump_stack+0x90/0xbc (unreliable)
>[c000000f1f603b30] [c0000000008e7e78] panic+0xf8/0x2c4
>[c000000f1f603bc0] [c000000000be4860] mount_block_root+0x288/0x33c
>[c000000f1f603c80] [c000000000be4d14] prepare_namespace+0x1f4/0x254
>[c000000f1f603d00] [c000000000be43e8] kernel_init_freeable+0x318/0x350
>[c000000f1f603dc0] [c00000000000bd74] kernel_init+0x24/0x130
>[c000000f1f603e30] [c0000000000095b0] ret_from_kernel_thread+0x5c/0xac
>---[ end Kernel panic - not

This functionality is implemented as a kmsg_dumper as it seems to be the
most sensible way to introduce platform-specific functionality to the
panic function.

Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-12-27 19:12:40 +11:00
Michael Neuling
2fc251a8dd powerpc: Copy only required pieces of the mm_context_t to the paca
Currently we copy the whole mm_context_t to the paca but only access a
few bits of it.  This is wasteful of space paca and also takes quite
some time in the hot path of context switching.

This patch pulls in only the required bits from the mm_context_t to
the paca and on context switch, copies only those.

Benchmarking this (On top of Anton's recent MSR context switching
changes [1]) using processes and yield shows an improvement of almost
3% on POWER8:

  http://ozlabs.org/~anton/junkcode/context_switch2.c
  ./context_switch2 --test=yield --process 0 0

1. https://lists.ozlabs.org/pipermail/linuxppc-dev/2015-October/135700.html

Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Rename paca fields to be mm_ctx_foo rather than context_foo]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-12-27 19:12:14 +11:00
Linus Torvalds
12261f4ed4 ARC fixes for
- Unwinder rework (A revert followed by better fix)
  - Build errors: MMUv2, modules with -Os
  - highmem section mismatch build splat
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWfjpNAAoJEGnX8d3iisJeC08P+wRkkvtK0R5iZPqfTdSUaxFz
 CYoVM8mAMF+non+b7a4bWHChDJ+HlHxqsQWbq2A/EsET/TOXmnr28KquC/qfplwd
 p2I38xxsCSHK0hU1+x47VdxZdtO5VNdp+fsq7CQbHLUwg9TMCK4t8OpslrA3IbOG
 W+YlHQ+7Wwgu1GbHhWOHDTPb/yqX0WByX211HomURlo9Ppi3Xv3W6xK7uGn0wUxS
 DKp0pEWhLs8UQh6zGAf3zFJVjuuWpJHwAoXmQgfEeXYkA/ZOBCEh8sf+/fFZMxuK
 RAItN1ZTV3HwIYh3ykJyap877MBksb7nsCE5R0l+LQW0nV485omfJgWvo2hFUL5D
 Nrr93bcu8msn/mKfYtBaaQdohwlGsNY5GFaRGEv6TgKZWifFX+uUOBnZnbr2RLvn
 3/cDeeK/24sYvxaHGvBs3tjnJkwWPpofr9ZHCnQT+X8MgxjHQhcBesDq/8lb90m6
 G2RRqXQomdKkMBacejpKyvnulTEwMrU9itpxyIT7wfxCVGKxfdWHNHLW8KNtXsDn
 02Ae7XUyuciV6RIF9lXyGa+I73T/4/ut02b4Qq7PrdfLQucwZKjIQ9nj1Om9+taV
 1nSdm+VttO/Nqu2PoMKluxNHBpS1kxzEVFZWa/mXfFs+qmwRMLyKqjz0Tog+hBCv
 O7951Yzp3J88HTQIwUMD
 =h2pT
 -----END PGP SIGNATURE-----

Merge tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc

Pull ARC fixes from Vineet Gupta:
 "Sorry for this late pull request, but these are all important fixes
  for code introduced/updated in this release which we will otherwise
  end up back porting.

   - Unwinder rework (A revert followed by better fix)
   - Build errors: MMUv2, modules with -Os
   - highmem section mismatch build splat"

* tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: dw2 unwind: Catch Dwarf SNAFUs early
  ARC: dw2 unwind: Don't bail for CIE.version != 1
  Revert "ARC: dw2 unwind: Ignore CIE version !=1 gracefully instead of bailing"
  ARC: Fix linking errors with CONFIG_MODULE + CONFIG_CC_OPTIMIZE_FOR_SIZE
  ARC: mm: fix building for MMU v2
  ARC: mm: HIGHMEM: Fix section mismatch splat
2015-12-26 14:58:06 -08:00
Eric Anholt
5234c34e4c ARM: bcm2835: Add Kconfig support for bcm2836
This should be a complete port of bcm2835 functionality to bcm2836
(Raspberry Pi 2).

Signed-off-by: Eric Anholt <eric@anholt.net>
2015-12-26 14:34:03 -08:00
Linus Torvalds
8db7b3c544 Merge branch 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc system call restart fix from Helge Deller:
 "The architectural design of parisc always uses two instructions to
  call kernel syscalls (delayed branch feature).  This means that the
  instruction following the branch (located in the delay slot of the
  branch instruction) is executed before control passes to the branch
  destination.

  Depending on which assembler instruction and how it is used in
  usersapce in the delay slot, this sometimes made restarted syscalls
  like futex() and poll() failing with -ENOSYS"

* 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix syscall restarts
2015-12-25 13:19:50 -08:00
Linus Torvalds
682cb0cd82 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:

 1) Finally make perf stack backtraces stable on sparc, several problems
    (mostly due to the context in which the user copies from the stack
    are done) contributed to this.

    From Rob Gardner.

 2) Export ADI capability if the cpu supports it.

 3) Hook up userfaultfd system call.

 4) When faults happen during user copies we really have to clean up and
    restore the FPU state fully.  Also from Rob Gardner

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  tty/serial: Skip 'NULL' char after console break when sysrq enabled
  sparc64: fix FP corruption in user copy functions
  sparc64: Perf should save/restore fault info
  sparc64: Ensure perf can access user stacks
  sparc64: Don't set %pil in rtrap_nmi too early
  sparc64: Add ADI capability to cpu capabilities
  tty: serial: constify sunhv_ops structs
  sparc: Hook up userfaultfd system call
2015-12-25 13:15:23 -08:00
Rob Gardner
a7c5724b5c sparc64: fix FP corruption in user copy functions
Short story: Exception handlers used by some copy_to_user() and
copy_from_user() functions do not diligently clean up floating point
register usage, and this can result in a user process seeing invalid
values in floating point registers. This sometimes makes the process
fail.

Long story: Several cpu-specific (NG4, NG2, U1, U3) memcpy functions
use floating point registers and VIS alignaddr/faligndata to
accelerate data copying when source and dest addresses don't align
well. Linux uses a lazy scheme for saving floating point registers; It
is not done upon entering the kernel since it's a very expensive
operation. Rather, it is done only when needed. If the kernel ends up
not using FP regs during the course of some trap or system call, then
it can return to user space without saving or restoring them.

The various memcpy functions begin their FP code with VISEntry (or a
variation thereof), which saves the FP regs. They conclude their FP
code with VISExit (or a variation) which essentially marks the FP regs
"clean", ie, they contain no unsaved values. fprs.FPRS_FEF is turned
off so that a lazy restore will be triggered when/if the user process
accesses floating point regs again.

The bug is that the user copy variants of memcpy, copy_from_user() and
copy_to_user(), employ an exception handling mechanism to detect faults
when accessing user space addresses, and when this handler is invoked,
an immediate return from the function is forced, and VISExit is not
executed, thus leaving the fprs register in an indeterminate state,
but often with fprs.FPRS_FEF set and one or more dirty bits. This
results in a return to user space with invalid values in the FP regs,
and since fprs.FPRS_FEF is on, no lazy restore occurs.

This bug affects copy_to_user() and copy_from_user() for NG4, NG2,
U3, and U1. All are fixed by using a new exception handler for those
loads and stores that are done during the time between VISEnter and
VISExit.

n.b. In NG4memcpy, the problematic code can be triggered by a copy
size greater than 128 bytes and an unaligned source address.  This bug
is known to be the cause of random user process memory corruptions
while perf is running with the callgraph option (ie, perf record -g).
This occurs because perf uses copy_from_user() to read user stacks,
and may fault when it follows a stack frame pointer off to an
invalid page. Validation checks on the stack address just obscure
the underlying problem.

Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-24 12:13:18 -05:00
Rob Gardner
833526941f sparc64: Perf should save/restore fault info
There have been several reports of random processes being killed with
a bus error or segfault during userspace stack walking in perf.  One
of the root causes of this problem is an asynchronous modification to
thread_info fault_address and fault_code, which stems from a perf
counter interrupt arriving during kernel processing of a "benign"
fault, such as a TSB miss. Since perf_callchain_user() invokes
copy_from_user() to read user stacks, a fault is not only possible,
but probable. Validity checks on the stack address merely cover up the
problem and reduce its frequency.

The solution here is to save and restore fault_address and fault_code
in perf_callchain_user() so that the benign fault handler is not
disturbed by a perf interrupt.

Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-24 12:12:46 -05:00
Rob Gardner
3f74306ac8 sparc64: Ensure perf can access user stacks
When an interrupt (such as a perf counter interrupt) is delivered
while executing in user space, the trap entry code puts ASI_AIUS in
%asi so that copy_from_user() and copy_to_user() will access the
correct memory. But if a perf counter interrupt is delivered while the
cpu is already executing in kernel space, then the trap entry code
will put ASI_P in %asi, and this will prevent copy_from_user() from
reading any useful stack data in either of the perf_callchain_user_X
functions, and thus no user callgraph data will be collected for this
sample period. An additional problem is that a fault is guaranteed
to occur, and though it will be silently covered up, it wastes time
and could perturb state.

In perf_callchain_user(), we ensure that %asi contains ASI_AIUS
because we know for a fact that the subsequent calls to
copy_from_user() are intended to read the user's stack.

[ Use get_fs()/set_fs() -DaveM ]

Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-24 12:10:29 -05:00
Rob Gardner
1ca04a4ce0 sparc64: Don't set %pil in rtrap_nmi too early
Commit 28a1f53 delays setting %pil to avoid potential
hardirq stack overflow in the common rtrap_irq path.
Setting %pil also needs to be delayed in the rtrap_nmi
path for the same reason.

Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-24 12:07:16 -05:00
Khalid Aziz
82924e542f sparc64: Add ADI capability to cpu capabilities
Add ADI (Application Data Integrity) capability to cpu capabilities list.
ADI capability allows virtual addresses to be encoded with a tag in
bits 63-60. This tag serves as an access control key for the regions
of virtual address with ADI enabled and a key set on them. Hypervisor
encodes this capability as "adp" in "hwcap-list" property in machine
description.

Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-24 12:05:06 -05:00
Peter Ujfalusi
f0ad43539a ARM: DTS: da850: Enable DMA for SPI1
Add the needed bindings so the SPI driver can use DMA with SPI1.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:32:14 +05:30
Peter Ujfalusi
3c497582e1 ARM: DTS: da850: Add node for mmc1
da850 has two MMC controller, MMCSD1 is served by eDMA1

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:32:14 +05:30
Peter Ujfalusi
684892a2f1 ARM: DTS: da850: Enable DMA use for MMC0
Add the needed bindings for MMC0 in order to be able to utilize the DMA
instead of PIO mode.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:32:14 +05:30
Peter Ujfalusi
b47a856069 ARM: DTS: da850: Enable eDMA1
The eDMA1 in da850 has only one TPTC and for example MMC1 is HW events are
handled by it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:32:14 +05:30
Peter Ujfalusi
7a7faedde6 ARM: DTS: da850: Use the new DT bindings for the eDMA3
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Using the new binding will allow us to reserve PaRAM slots to be used by
the DSP which was not possible before and prevented the da850 boards to be
moved to DT only.

Note that the DMA memcpy is disabled, it can be enabled by reserving
channels for memcpy by adding the following property to the edma node:
ti,edma-memcpy-channels = <20 21>; /* Reserving channel 20 and 21 for memcpy */

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:32:14 +05:30
Peter Ujfalusi
dfaebb509b ARM: DTS: da850: fix edma0 reg space
The size of the eDMA0 CC register space is 0x8000 and not 0x10000.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2015-12-24 16:20:38 +05:30
Hongtao Jia
3045e409e4 powerpc/mpc85xx: Add TMU device tree support for T1023/T1024
Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.

Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-23 22:21:11 -06:00
Hongtao Jia
be489a3936 powerpc/mpc85xx: Add TMU device tree support for T1040/T1042
Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.

Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-23 22:21:11 -06:00
Dave Airlie
20f8e032e6 Backmerge drm-fixes merge into Linus's tree into drm-next.
This merges '5b726e06d6' into drm-next

Just to resolve some merges to make Daniel's life easier.

Signed-off-by: DAve Airlie <airlied@redhat.com>
2015-12-24 08:08:47 +10:00
Raghav Dogra
479f6a7fc6 powerpc/fsl_lbc: removal of dead code
The condition check is not used.

Signed-off-by: Raghav Dogra <raghav@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-23 15:02:00 -06:00
Mike Kravetz
9bcfd78ac0 sparc: Hook up userfaultfd system call
After hooking up system call, userfaultfd selftest was successful for
both 32 and 64 bit version of test.

Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-23 15:41:13 -05:00
Li Bin
e9b349f089 metag: ftrace: Fix the comments for ftrace_modify_code
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449367378-29430-3-git-send-email-huawei.libin@huawei.com

Cc: linux-metag@vger.kernel.org
Acked-by: James Hogan <james.hogan@imgtec.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-12-23 14:27:25 -05:00
Li Bin
5243238ad5 sh: ftrace: Fix the comments for ftrace_modify_code()
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449367378-29430-5-git-send-email-huawei.libin@huawei.com

Cc: linux-sh@vger.kernel.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-12-23 14:27:24 -05:00
Li Bin
cbbe12c43d ia64: ftrace: Fix the comments for ftrace_modify_code()
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449214067-12177-2-git-send-email-huawei.libin@huawei.com

Cc: linux-ia64@vger.kernel.org
Acked-by: Tony Luck <tony.luck@intel.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-12-23 14:27:23 -05:00
Al Viro
c62432b40b [mips] switch pvc_proc_cleanup() to remove_proc_subtree()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-12-23 10:41:38 -05:00
Al Viro
b25472f9b9 new helpers: no_seek_end_llseek{,_size}()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-12-23 10:41:31 -05:00
Thomas Gleixner
b92c453d52 Revert "x86/kvm: On KVM re-enable (e.g. after suspend), update clocks"
This reverts commit 677a73a9aa. This patch was not meant to be merged and
has issues. Revert it.

Requested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-12-23 12:35:21 +01:00
Takashi Iwai
f80e39e022 ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
 drivers being added but comparatively quiet on the core side with only
 one big change going in and that a fairly straightforward refactoring.
 
  - Conversion of the array of DAI links to a list by Mengdong Lin,
    supporting dynamically adding and removing DAI links.
  - Some more fixes for the topology code, though it is still not final
    and ready for enabling in production.  We really need to get to the
    point where that can be done.
  - A pile of changes for Intel SkyLake drivers which hopefully deliver
    some useful initial functionality for systems with this chipset,
    though there is more work still to come.
  - New drivers for a number of Imagination Technologies IPs.
  - Lots of new features and cleanups for the Renesas drivers.
  - ANC support for WM5110.
  - New driver for Atmel class D speaker drivers.
  - New drivers for Cirrus CS47L24 and WM1831.
  - New driver for Dialog DA7128.
  - New drivers for Realtek RT5659 and RT56156.
  - New driver for Rockchip RK3036.
  - New driver for TI PC3168A
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
 HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
 9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
 oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
 6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
 PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
 =d18k
 -----END PGP SIGNATURE-----

Merge tag 'asoc-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v4.5

This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.

 - Conversion of the array of DAI links to a list by Mengdong Lin,
   supporting dynamically adding and removing DAI links.
 - Some more fixes for the topology code, though it is still not final
   and ready for enabling in production.  We really need to get to the
   point where that can be done.
 - A pile of changes for Intel SkyLake drivers which hopefully deliver
   some useful initial functionality for systems with this chipset,
   though there is more work still to come.
 - New drivers for a number of Imagination Technologies IPs.
 - Lots of new features and cleanups for the Renesas drivers.
 - ANC support for WM5110.
 - New driver for Atmel class D speaker drivers.
 - New drivers for Cirrus CS47L24 and WM1831.
 - New driver for Dialog DA7128.
 - New drivers for Realtek RT5659 and RT56156.
 - New driver for Rockchip RK3036.
 - New driver for TI PC3168A
2015-12-23 08:33:52 +01:00
Takashi Iwai
59c8231089 Merge branch 'for-linus' into for-next
Conflicts:
	drivers/gpu/drm/i915/intel_pm.c
2015-12-23 08:33:34 +01:00
Tony Lindgren
dbb7e70a69 ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
Fix warning for arch/arm/mach-omap2/prm_common.c:666:35: warning:
‘dm814_pllss_data’ defined but not used [-Wunused-variable]".

This can happen if CONFIG_SOC_TI81XX is not selected.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-12-22 17:01:02 -08:00
Mark Brown
14418aa7d4 Merge remote-tracking branches 'asoc/topic/samsung', 'asoc/topic/sh', 'asoc/topic/ssm2518' and 'asoc/topic/sti' into asoc-next 2015-12-23 00:23:51 +00:00
Mark Brown
b9546d09b1 Merge remote-tracking branches 'asoc/topic/fsl-spdif', 'asoc/topic/img' and 'asoc/topic/intel' into asoc-next 2015-12-23 00:23:43 +00:00
Zhao Qiang
b0417a2870 powerpc/p1010rdb: Update dts for pcie interrupt-map
p1010rdb uses the irq[4:5] for inta and intb to pcie,
it is active-high, so set it.

Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-22 18:23:22 -06:00
Scott Wood
2749539b4b powerpc/e6500: add locking to hugetlb
e6500 has threads but does not have TLB write conditional.  Thus,
the hugetlb code needs to take the same lock that the normal TLB miss
handlers take, to ensure that the tlbsx and tlbwe are atomic.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-22 18:23:22 -06:00
li pengbo
9d68e7accf powerpc/85xx: Enable TWR_P102x in mpc85xx_basic_defconfig
Enable TWR_P102x option by default in mpc85xx_basic_defconfig to support
p1025twr board.

Signed-off-by: Pengbo Li <Pengbo.Li@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-22 18:23:21 -06:00
Daniel Walker
433c858a61 powerpc/85xx: mpc85xx ADS: remove pci exclude
This code was reworked in commit,

905e75c46d

This change removed the fsl_add_bridge() which originally was above
the addition of the pci_exclude_device function. I think the assumption was that
the pci_exclude_device would prevent changes to the bridge PCI config after
it's been added. It seems it wasn't fully tested on MPC85xx ADS because
if you move the fsl_add_bridge() the pci_exclude_device is set in the machine
description then you can never update the PCI Config since the exclude
prevents it. This disrupts things like DMA.

This issue was extensively debugged by David Beazley.

Cc: xe-kernel@external.cisco.com
Cc: dbeazley@cisco.com
Cc: dwalker@fifo99.com
Signed-off-by: Daniel Walker <danielwa@cisco.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-22 18:23:21 -06:00
Igal Liberman
4e9de5e970 powerpc/mpc85xx: Update B4 FMan MURAM size
FMan V3H has 2 different MURAM sizes:
    In B4860/4420 the MURAM size is 512KB.
    In T4240 and T2080 the MURAM size is 384KB.

The MURAM size in FMan V3H device tree is 384KB.
This patch updates the MURAM size for B4 to 512KB.

Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-22 18:23:11 -06:00
Tony Lindgren
f53850b5dc ARM: OMAP2+: Add support for dm814x and dra62x usb
The usb phys are different on dm814x compared to dm816x so we need to
use the clkdcoldo output for usb.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-12-22 16:23:08 -08:00