Instantiate all serial devices in r8a7793 device tree
and set them as disabled by default.
Based on similar work for the r8a7791 by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable timestamps for kernel log output to improve debugging.
You can always use "dmesg -t" to strip the timestamps.
Don't specify CONFIG_LOG_BUF_SHIFT=16 while we're at it. There's a
reason the default in Kconfig is higher ;-)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Add serial port config to chosen/stdout-path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have never had dm814x booting properly with mainline kernel using
the legacy platform data based booting. Current minimal support is
device tree only.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise pinctrl won't work. Because of silicon errata for some dm814x
versions, let's also keep bit 18 out of the function-mask and rely on
the bootloader configuration for bit 18 as suggested by
Matthijs van Duin <matthijsvanduin@gmail.com>.
Devices with that need to use bit 18 can override the function-mask in
the board specific dts file if really needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The control module is at offset 0x14000 with size 0x20000, not 0x16000.
This causes the pinctrl driver to not work.
Let's also fix the comments related to the TRM "L4LS Instance Summary"
table as that's what's causing the bad entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a mux after the oscillator similar to am335x. I did not
notice this on hp t410 as it boots even with no clocks configured.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although we have hp t410 booting, I noticed that dm814x-evm does not boot
after I got one. This is because we don't have the clocks yet configured
properly. Let's start configuring proper clocks starting with the system
timers and clocks that work with existing mux and divider clock drivers.
Note that the oscillator speed register is different from am335x, dm814x
has only one bit that shows the BTMODE[6] at CONTROL_STATUS[21].
Also note that this only gets the system timers working with the defined
clocks. The PLL clocks are still missing and and the devices may or may
not work depending on what the bootloader has enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dm814x we have some clocks at DPLLS and some at PRCM. Let's add a new
omap_prcm_init_data entry for the DPLLS so we can initalize timer clocks
early.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only using 32 memslots for KVM on powerpc is way too low, you can
nowadays hit this limit quite fast by adding a couple of PCI devices
and/or pluggable memory DIMMs to the guest.
x86 already increased the KVM_USER_MEM_SLOTS to 509, to satisfy 256
pluggable DIMM slots, 3 private slots and 253 slots for other things
like PCI devices (i.e. resulting in 256 + 3 + 253 = 512 slots in
total). We should do something similar for powerpc, and since we do
not use private slots here, we can set the value to 512 directly.
While we're at it, also remove the KVM_MEM_SLOTS_NUM definition
from the powerpc-specific header since this gets defined in the
generic kvm_host.h header anyway.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently it is possible for userspace (e.g. QEMU) to set a value
for the MSR for a guest VCPU which has both of the TS bits set,
which is an illegal combination. The result of this is that when
we execute a hrfid (hypervisor return from interrupt doubleword)
instruction to enter the guest, the CPU will take a TM Bad Thing
type of program interrupt (vector 0x700).
Now, if PR KVM is configured in the kernel along with HV KVM, we
actually handle this without crashing the host or giving hypervisor
privilege to the guest; instead what happens is that we deliver a
program interrupt to the guest, with SRR0 reflecting the address
of the hrfid instruction and SRR1 containing the MSR value at that
point. If PR KVM is not configured in the kernel, then we try to
run the host's program interrupt handler with the MMU set to the
guest context, which almost certainly causes a host crash.
This closes the hole by making kvmppc_set_msr_hv() check for the
illegal combination and force the TS field to a safe value (00,
meaning non-transactional).
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Paul Mackerras <paulus@samba.org>
This refactors the EFI init and runtime code that will be shared
between arm64 and ARM so that it can be built for both archs.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This splits off the early EFI init and runtime code that
- discovers the EFI params and the memory map from the FDT, and installs
the memblocks and config tables.
- prepares and installs the EFI page tables so that UEFI Runtime Services
can be invoked at the virtual address installed by the stub.
This will allow it to be reused for 32-bit ARM.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Change the EFI memory reservation logic to use memblock_mark_nomap()
rather than memblock_reserve() to mark UEFI reserved regions as
occupied. In addition to reserving them against allocations done by
memblock, this will also prevent them from being covered by the linear
mapping.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Take the new memblock attribute MEMBLOCK_NOMAP into account when
deciding whether a certain region is or should be covered by the
kernel direct mapping.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Running with CONFIG_DEBUG_SPINLOCK=y can trigger a BUG with the new IRQ
stack code:
BUG: spinlock lockup suspected on CPU#1
This is due to the IRQ_STACK_TO_TASK_STACK macro incorrectly retrieving
the task stack pointer stashed at the top of the IRQ stack.
Sayeth James:
| Yup, this is what is happening. Its an off-by-one due to broken
| thinking about how the stack works. My broken thinking was:
|
| > top ------------
| > | dummy_lr | <- irq_stack_ptr
| > ------------
| > | x29 |
| > ------------
| > | x19 | <- irq_stack_ptr - 0x10
| > ------------
| > | xzr |
| > ------------
|
| But the stack-pointer is decreased before use. So it actually looks
| like this:
|
| > ------------
| > | | <- irq_stack_ptr
| > top ------------
| > | dummy_lr |
| > ------------
| > | x29 | <- irq_stack_ptr - 0x10
| > ------------
| > | x19 |
| > ------------
| > | xzr | <- irq_stack_ptr - 0x20
| > ------------
|
| The value being used as the original stack is x29, which in all the
| tests is sp but without the current frames data, hence there are no
| missing frames in the output.
|
| Jungseok Lee picked it up with a 32bit user space because aarch32
| can't use x29, so it remains 0 forever. The fix he posted is correct.
This patch fixes the macro and adds some of this wisdom to a comment,
so that the layout of the IRQ stack is well understood.
Cc: James Morse <james.morse@arm.com>
Reported-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The properties specified in the wled node could harm connected hardware,
so move the properties to Honami and disable the platform node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add the generic compatible strings for the PMIC gpio and MPP
modules found on qcom based PMICs.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add an alias for the PMICs found on qcom based SoCs so that the
newly updated dtbTool can find the PMIC compatible string and add
the pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The ifc6540 is an sbc (single board computer) board, so update
the compatible field accordingly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
These clocks are fixed rate board sources that should be in DT.
Add them.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This introduces initial support for the Sony Xperia Z smartphone, including
support for UART, MMC, USB gadget and physical buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Consolidate all labeling of regulators into the core 8064 dtsi file to
make them available from all other dts files.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add devicetree data to add support for hw_rng support
to the apq8064 dts.
Tested on the Nexus7 (2013).
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add and enable the sdhci2 slot, the pinctrl configuration and card
detect.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce the eMMC sdhci node and its pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce a gpio-keys node defining the physical keys of the Honami and
the associated pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Make sure the blsp1_uart2 pins are in the correct state for the uart.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The vcpu_book3s variable is assigned but never used. So remove it.
Found using cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the old DABR register, the BT (Breakpoint Translation) bit
is bit number 61. In the new DAWRX register, the WT (Watchpoint
Translation) bit is bit number 59. So to move the DABR-BT bit
into the position of the DAWRX-WT bit, it has to be shifted by
two, not only by one. This fixes hardware watchpoints in gdb of
older guests that only use the H_SET_DABR/X interface instead
of the new H_SET_MODE interface.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As we saw with the TM Bad Thing type of program interrupt occurring
on the hrfid that enters the guest, it is not completely impossible
to have a trap occurring in the guest entry/exit code, despite the
fact that the code has been written to avoid taking any traps.
This adds a check in the kvmppc_handle_exit_hv() function to detect
the case when a trap has occurred in the hypervisor-mode code, and
instead of treating it just like a trap in guest code, we now print
a message and return to userspace with a KVM_EXIT_INTERNAL_ERROR
exit reason.
Of the various interrupts that get handled in the assembly code in
the guest exit path and that can return directly to the guest, the
only one that can occur when MSR.HV=1 and MSR.EE=0 is machine check
(other than system call, which we can avoid just by not doing a sc
instruction). Therefore this adds code to the machine check path to
ensure that if the MCE occurred in hypervisor mode, we exit to the
host rather than trying to continue the guest.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 527d10ef3a.
The reverted commit breaks cxlflash devices following an EEH reset (and
possibly other cxl devices, however this has not been tested).
The reverted commit changed the behaviour of eeh_reset_device() so that PHB
PEs are not unfrozen following the completion of the reset. This should not
be problematic, as no device resources should have been associated with the
PHB PE.
However, when attempting to load the cxlflash driver after a reset, the
driver attempts to read Vital Product Data through a call to
pci_read_vpd() (which is called on the physical cxl device, not on the
virtual AFU device). pci_read_vpd() in turn attempts to read from the cxl
device's config space. This fails, as the PE it's trying to read from is
still frozen. In turn, the driver gets an -ENODEV and fails to initialise.
It appears this issue only affects some parts of the VPD area, as "lspci
-vvv", which only reads a subset of the VPD bytes, is not broken by the
original patch.
At this stage, we don't fully understand why we're trying to read a frozen
PE, and we don't know how this affects other cxl devices. It is possible
that there is an underlying bug in the cxl driver or the powerpc CAPI
support code, or alternatively a bug in the PCI resource allocation/mapping
code that is incorrectly mapping resources to PE#0.
As such, this fix is incomplete, however it is necessary to prevent a
serious regression in CAPI support.
In the meantime, revert the commit, especially as it was intended to be a
non-functional change.
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This file was originally cloned off of the MPC8641D-HPCN reference
platform, which actually had a PHY IRQ line connected. However this
board does not. The bogus entry was largely inert and went undetected
until commit 321beec504 ("net: phy: Use
interrupts when available in NOLINK state") was added to the tree.
With the above commit, the board fails to NFS boot since it sits waiting
for a PHY IRQ event that of course never arrives. Removing the bogus
entries from the DTS file fixes the issue.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull uml fixes from Richard Weinberger:
"This contains various bug fixes, most of them are fall out from the
merge window"
* 'for-linus-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: fix returns without va_end
um: Fix fpstate handling
arch: um: fix error when linking vmlinux.
um: Fix get_signal() usage
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>