Commit graph

127,691 commits

Author SHA1 Message Date
Ilya Ledvich
15be8179e4 ARM: dts: cm-t335: add initial support
Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM)
The module is built around the Texas Instruments Sitara AM3352/4
system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board
NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit
Ethernet, CAN bus.

Current patch adds support:
UART0 and GPIO LED

Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
[uri.mashiach@compulab.co.il: the default RAM amount reduced to
128MB to support also the minimal module configuration]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 14:03:47 -08:00
Adam Ford
b6f0f6c40b ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo
The schematic expects VAUX1 to be 3.0V attached to the debug port.
The schematic expects VAUX4 to be 1.8V.
VAUX4 powers VDDS_CSI2 on processor.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 14:03:47 -08:00
Adam Ford
7cd6ca770d ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit
When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 14:03:47 -08:00
Dave Airlie
80d69009ef Merge tag 'drm-intel-next-2015-11-20-merged' of git://anongit.freedesktop.org/drm-intel into drm-next
drm-intel-next-2015-11-20-rebased:
4 weeks because of my vacation, so a bit more:
- final bits of the typesafe register mmio functions (Ville)
- power domain fix for hdmi detection (Imre)
- tons of fixes and improvements to the psr code (Rodrigo)
- refactoring of the dp detection code (Ander)
- complete rework of the dmc loader and dc5/dc6 handling (Imre, Patrik and
  others)
- dp compliance improvements from Shubhangi Shrivastava
- stop_machine hack from Chris to fix corruptions when updating GTT ptes on bsw
- lots of fifo underrun fixes from Ville
- big pile of fbc fixes and improvements from Paulo
- fix fbdev failures paths (Tvrtko and Lukas Wunner)
- dp link training refactoring (Ander)
- interruptible prepare_plane for atomic (Maarten)
- basic kabylake support (Deepak&Rodrigo)
- don't leak ringspace on resets (Chris)
drm-intel-next-2015-10-23:
- 2nd attempt at atomic watermarks from Matt, but just prep for now
- fixes all over

* tag 'drm-intel-next-2015-11-20-merged' of git://anongit.freedesktop.org/drm-intel: (209 commits)
  drm/i915: Update DRIVER_DATE to 20151120
  drm/i915: take a power domain reference while checking the HDMI live status
  drm/i915: take a power domain ref only when needed during HDMI detect
  drm/i915: Tear down fbdev if initialization fails
  async: export current_is_async()
  Revert "drm/i915: Initialize HWS page address after GPU reset"
  drm/i915: Fix oops caused by fbdev initialization failure
  drm/i915: Fix i915_ggtt_view_equal to handle rotation correctly
  drm/i915: Stuff rotation params into view union
  drm/i915: Drop return value from intel_fill_fb_ggtt_view
  drm/i915 : Fix to remove unnecsessary checks in postclose function.
  drm/i915: add MISSING_CASE to a few port/aux power domain helpers
  drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
  drm/i915: Remove platform specific *_dp_detect() functions
  drm/i915: Don't do edp panel detection in g4x_dp_detect()
  drm/i915: Send TP1 TP2/3 even when panel claims no NO_TRAIN_ON_EXIT.
  drm/i915: PSR: Don't Skip aux handshake on DP_PSR_NO_TRAIN_ON_EXIT.
  drm/i915: Reduce PSR re-activation time for VLV/CHV.
  drm/i915: Delay first PSR activation.
  drm/i915: Type safe register read/write
  ...
2015-12-01 08:01:53 +10:00
Franklin S Cooper Jr
c9fbaa4997 ARM: omap4: hwmod: Remove elm address space from hwmod data
ELM address information is provided by device tree. No longer need
to include this information within hwmod.

This patch has only been boot tested.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 13:18:37 -08:00
Suman Anna
ed5a4c6248 ARM: OMAP2+: timer: Remove secure timer for DRA7xx HS devices
Timer 12 on DRA7 SoCs is reserved for secure usage on high-secure (HS)
devices. The timer cannot be used by the kernel on HS devices, but is
available on regular general purpose (GP) devices. This is similar to the
behavior on OMAP3 devices, so extend the logic used in commit ad24bde8f1
("ARM: OMAP3: Dynamically disable secure timer nodes for secure devices")
to remove the secure timer on DRA7xx SoCs at run-time based on the SoC
device type.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 13:18:23 -08:00
Suman Anna
ea05d2eaf6 ARM: OMAP: dmtimer: check for fixed timers during config
The omap_dm_timer_set_source() function provides a means for client
users to configure the mux parent for a GPTimer's functional clock.
However, not all timers are configurable (Eg: Timer12 on DRA7 is fed
by an internal 32k oscillator clock, and does not have configurable
parent clocks). So, check for such cases and proceed with out throwing
an error.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 13:18:23 -08:00
Tero Kristo
07ff73a932 clk: ti: omap5+: dpll: implement errata i810
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.

As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.

This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-11-30 11:34:17 -08:00
Adam Ford
9ff502f58a ARM: dts: Enable UART2 pinctrl on LogicPD Torpedo + Wireless module
Setup UART2 for communication at 3MBps with flow control.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
[tony@atomide.com: dropped the kim changes, that binding has been removed]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 11:18:44 -08:00
Adam Ford
2d11961f3e ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively
The development kit schematic expects VAUX1 to be 3.0V.  Most users use the development kit as a reference.
The development kit schematic expects VAUX4 to be 1.8V.  VAUX4 powers VDDS_CSI2 on processor.  If the voltage is too high it could damage the processor.
If it's too low, it won't work.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 11:17:39 -08:00
Adam Ford
6b3d42c6fc ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit
When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 11:17:24 -08:00
Adam Ford
f81902e44a ARM: dts: Add audio support for LogicPD Torpedo DM3730 devkit
Use the TWL4030 Codec with mcbsp2 on Torpedo.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 11:17:08 -08:00
Franklin S Cooper Jr
201c7e3386 ARM: dts: am437x/am33xx/omap/dm816x: Add gpmc dma channel
Add dma channel information to the gpmc. Although not enabled by
default this will allow prefetch-dma to be used.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 11:03:35 -08:00
Suman Anna
1ad0ea0c65 ARM: OMAP4: hwmod data: Remove legacy IOMMU attr and addrs
OMAP4 has been DT-boot only for some time, and the legacy-mode
device creation logic for IOMMU devices has also been cleaned up,
so the dev_attr and address data is no longer required. So, remove
these attribute data and hwmod addr space for the IPU & DSP IOMMU
devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:35:07 -08:00
Suman Anna
621062f49b ARM: OMAP3: hwmod data: Remove legacy IOMMU data
The legacy-mode device creation logic for IOMMU devices has
been cleaned up, so the device attribute data, irq information
and address data are no longer required. Remove all of these
data for the ISP & IVA IOMMU devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to apply for the include]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:35:07 -08:00
Suman Anna
dd20b0d5c7 ARM: OMAP2+: Remove legacy device instantiation of IOMMUs
The legacy-style IOMMU device creation is maintained currently only
for OMAP3 SoC, as all other SoCs are DT-boot only, and also to ensure
functionality of the OMAP3 ISP driver, the only in-kernel client user
on OMAP3 that supported both modes.

Commit 78c66fbcec ("[media] v4l: omap3isp: Drop platform data support")
removed the legacy device support from the OMAP3 ISP driver, so the
legacy device instantiation of OMAP IOMMU devices is no longer
needed, and is cleaned up.

Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to remove also the Makefile entry]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:35:07 -08:00
Neil Armstrong
1539569bc9 ARM: OMAP2+: Add hwmod spinbox support for dm816x
Add dm81xx hwmod data entries for dm816x spinbox support.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:35:07 -08:00
Neil Armstrong
8c0cabd797 ARM: OMAP: add DT support for ti,dm816-timer
Adds ti,dm816-timer to the dmtimer OF match table.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:35:07 -08:00
Neil Armstrong
f1b2e7c29a ARM: dts: add dm816x missing spi DT dma handles
Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:21:17 -08:00
Neil Armstrong
d3e41a9fc0 ARM: dts: add dm816x missing #mbox-cells
Add missing #mbox-cells for dm816x mbox DT node.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:20:31 -08:00
Neil Armstrong
24f098220c ARM: dts: Add omap4-hwspinlock support in dm816x
Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:19:08 -08:00
Neil Armstrong
727535fd20 ARM: dts: remove dm816x invalid DT l3_main hwmod
Remove invalid l3_main hwmod entry from dm816x DT ocp node.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:19:08 -08:00
Neil Armstrong
8ca31dbf67 ARM: dts: add dm816x pwm property to timers
Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their
PWM output fonctionnality via the dmtimer driver.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:19:08 -08:00
Neil Armstrong
31a7448f4f ARM: OMAP: dmtimer: Add clock source from DT
Add a function which sets the timer source from the clocks
binding on dm_timer_prepare call.

In case the clocks property is not valid, it falls back to
the set_source() with 32_KHZ clock as default.

Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 10:00:05 -08:00
Dan Williams
bc0d0d093b libnvdimm, e820: skip module loading when no type-12
If there are no persistent memory ranges present then don't bother
creating the platform device.  Otherwise, it loads the full libnvdimm
sub-system only to discover no resources present.

Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2015-11-30 09:10:33 -08:00
Andrew F. Davis
df10eadfce ARM: dts: am335x-boneblack: Use pinctrl constants and AM33XX_IOPAD macro
Using constants for pinctrl allows better readability and removes
redundancy with comments. AM33XX_IOPAD allows us to use part of the
pinctrl physical address as in the TRM instead of an offset.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:48:52 -08:00
Javier Martinez Canillas
03c84de82e ARM: dts: omap5-uevm.dts: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:32 -08:00
Javier Martinez Canillas
92245d420e ARM: dts: omap5-cm-t54: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:32 -08:00
Javier Martinez Canillas
2fcf367a6c ARM: dts: omap5-board-common: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:31 -08:00
Javier Martinez Canillas
56ed5665eb ARM: dts: twl6030: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:31 -08:00
Javier Martinez Canillas
ed04b3747c ARM: dts: omap4-sdp-es23plus: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:31 -08:00
Javier Martinez Canillas
b6bf441ea4 ARM: dts: omap4-sdp: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:30 -08:00
Javier Martinez Canillas
67832f5277 ARM: dts: omap4-panda-es: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:30 -08:00
Javier Martinez Canillas
0e3ae3281d ARM: dts: omap4-panda-common: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:30 -08:00
Javier Martinez Canillas
37990123cd ARM: dts: omap4-panda-a4: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:29 -08:00
Javier Martinez Canillas
ececfa31e5 ARM: dts: twl4030: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:29 -08:00
Javier Martinez Canillas
ff523e3167 ARM: dts: omap3-zoom3: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:28 -08:00
Javier Martinez Canillas
53ccdd4b99 ARM: dts: omap3-n9: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:28 -08:00
Javier Martinez Canillas
675e457c45 ARM: dts: omap3-n900: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:28 -08:00
Javier Martinez Canillas
97f4817cce ARM: dts: omap3-ldp: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:27 -08:00
Javier Martinez Canillas
8acf1b30c8 ARM: dts: omap3-evm-37xx: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:27 -08:00
Javier Martinez Canillas
0ba47e4306 ARM: dts: omap3-beagle-xm: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:27 -08:00
Javier Martinez Canillas
161312d6e2 ARM: dts: omap3-beagle: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:26 -08:00
Javier Martinez Canillas
9255ea8472 ARM: dts: dra72-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:26 -08:00
Javier Martinez Canillas
c78be3d82e ARM: dts: dra7-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:26 -08:00
Javier Martinez Canillas
f70dfa6648 ARM: dts: am57xx-beagle-x15: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:25 -08:00
Javier Martinez Canillas
43ade6a33c ARM: dts: am43x-epos-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:25 -08:00
Javier Martinez Canillas
e98ceb23e4 ARM: dts: am437x-sk-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:25 -08:00
Javier Martinez Canillas
8e7d3dd924 ARM: dts: am437x-idk-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:24 -08:00
Javier Martinez Canillas
596bad7dc4 ARM: dts: am437x-gp-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-11-30 08:43:24 -08:00