Commit graph

127,691 commits

Author SHA1 Message Date
Simon Horman
6c04d2f7f1 arm64: defconfig: Enable SDHI and GPIO_REGULATOR
This allows use of the SDHI SD/SDIO controller present on R-Car Gen3 SoCs
and already enabled in the DT of the r8a7795/salvator-x (H3).

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2016-09-01 16:32:46 +02:00
Bjorn Helgaas
6af7e4f772 PCI: Mark Haswell Power Control Unit as having non-compliant BARs
The Haswell Power Control Unit has a non-PCI register (CONFIG_TDP_NOMINAL)
where BAR 0 is supposed to be.  This is erratum HSE43 in the spec update
referenced below:

  The PCIe* Base Specification indicates that Configuration Space Headers
  have a base address register at offset 0x10.  Due to this erratum, the
  Power Control Unit's CONFIG_TDP_NOMINAL CSR (Bus 1; Device 30; Function
  3; Offset 0x10) is located where a base register is expected.

Mark the PCU as having non-compliant BARs so we don't try to probe any of
them.  There are no other BARs on this device.

Rename the quirk so it's not Broadwell-specific.

Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v3-spec-update.html
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v3-datasheet-vol-2.html (section 5.4, Device 30 Function 3)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=153881
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
2016-09-01 08:52:29 -05:00
Will Deacon
e937dd5782 arm64: debug: convert OS lock CPU hotplug notifier to new infrastructure
The arm64 debug monitor initialisation code uses a CPU hotplug notifier
to clear the OS lock when CPUs come online.

This patch converts the code to the new hotplug mechanism.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-01 13:45:58 +01:00
Will Deacon
d7a83d127a arm64: hw_breakpoint: convert CPU hotplug notifier to new infrastructure
The arm64 hw_breakpoint implementation uses a CPU hotplug notifier to
reset the {break,watch}point registers when CPUs come online.

This patch converts the code to the new hotplug mechanism, whilst moving
the invocation earlier to remove the need to disable IRQs explicitly in
the driver (which could cause havok if we trip a watchpoint in an IRQ
handler whilst restoring the debug register state).

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-01 13:45:51 +01:00
Marek Szyprowski
47aabaf5a8 ARM: dts: exynos: Add all required FIMC-IS clocks to exynos4x12
FIMC-IS blocks must control 3 more clocks ("gicisp", "mcuctl_isp" and
"pwm_isp") to make the hardware fully operational.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2016-09-01 13:03:38 +02:00
zijun_hu
a842789837 arm64: remove duplicate macro __KERNEL__ check
remove duplicate macro __KERNEL__ check

Signed-off-by: zijun_hu <zijun_hu@htc.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-01 11:54:19 +01:00
York Sun
eeb3d68b6c EDAC, layerscape: Add Layerscape EDAC support
Add DDR EDAC driver for ARM-based compatible controllers. Both
big-endian and little-endian are supported, as specified in device tree.

Signed-off-by: York Sun <york.sun@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1471990465-27443-1-git-send-email-york.sun@nxp.com
Signed-off-by: Borislav Petkov <bp@suse.de>
2016-09-01 10:28:03 +02:00
Andy Shevchenko
3976b0380b x86/platform/intel-mid: Enable SD card detection on Merrifield
Intel Merrifield platform provides SD card interface. The interface allows user
to plug SD card to extend storage capacity.

Append the essential data to enable SD card detection on it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160831135713.79066-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-09-01 08:22:42 +02:00
Andy Shevchenko
dd8d6ec672 x86/platform/intel-mid: Enable WiFi on Intel Edison
Intel Edison board provides built-in WiFi dongle based on Broadcom BCM43340.

Append the essential data to enable WiFi on Intel Edison.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160831135713.79066-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-09-01 08:22:42 +02:00
Nishanth Menon
11b897a2f7 ARM: dts: keystone-k2g: Add Message Manager node
Introduce the message manager node for the A15 queues on which Linux
runs. The Message Manager is primarily used for communication with
Power Management controller on K2G.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:32:16 -04:00
Andrew F. Davis
e0f0b54c02 ARM: dts: keystone-k2g: Add DSP GPIO controller node
Add the DSP GPIO controller node on K2G SoC.
This is used to send interrupts to the only DSP processor
subsystem present on the SoC. The IP is identical to that
of the equivalent nodes on existing K2 SoCs.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:29:59 -04:00
Andrew F. Davis
0884b1b338 ARM: dts: keystone-k2g: Add keystone IRQ controller node
Add the Keystone IRQ controller IP node on K2G SoC. This allows the
ARM CorePac core to receive interrupts from remote processor devices
(eg: DSP) on the SoC.

The IP is identical in functionality to that of the equivalent
nodes on existing K2 SoCs. The only difference is the ARM INTC
interrupt id/event number.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:29:59 -04:00
Andrew F. Davis
08fa198ded ARM: dts: keystone-k2g: Add device state controller node
Add the device state controller node as a syscon node to the
K2G SoC. This module provides similar device control functionality
as that on the existing K2 SoCs.

One example usage would be the boot address programming of the
DSP processor sub-system.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:29:59 -04:00
Grygorii Strashko
644978440c ARM: dts: keystone: specify usb mode explicitly
The USB OTG mode is not supported by Kestone 2 devices, as result, the
USB devices enumeration and detection will not work properly when
kernel is built with CONFIG_USB_DWC3_DUAL_ROLE=y (default for multi
platform build):
 - it's required to load gadget drivers manually to make host mode
work and this confuses current Keystone 2 users
 - device mode is not working, because port can't detect and switch to
peripheral/host mode dynamically.

Hence, specify usb mode explicitly in DT: usb0 = "host" for all KS2
devices and usb1 = "peripheral" for K2E.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:29:59 -04:00
Roger Quadros
81b1f69e01 ARM: keystone: defconfig: Fix USB configuration
Simply enabling CONFIG_KEYSTONE_USB_PHY doesn't work anymore
as it depends on CONFIG_NOP_USB_XCEIV. We need to enable
that as well.

This fixes USB on Keystone boards from v4.8-rc1 onwards.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2016-08-31 16:10:50 -04:00
Will Deacon
3a402a7095 arm64: debug: avoid resetting stepping state machine when TIF_SINGLESTEP
When TIF_SINGLESTEP is set for a task, the single-step state machine is
enabled and we must take care not to reset it to the active-not-pending
state if it is already in the active-pending state.

Unfortunately, that's exactly what user_enable_single_step does, by
unconditionally setting the SS bit in the SPSR for the current task.
This causes failures in the GDB testsuite, where GDB ends up missing
expected step traps if the instruction being stepped generates another
trap, e.g. PTRACE_EVENT_FORK from an SVC instruction.

This patch fixes the problem by preserving the current state of the
stepping state machine when TIF_SINGLESTEP is set on the current thread.

Cc: <stable@vger.kernel.org>
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 17:49:19 +01:00
Milo Kim
a37b7a5a86 ARM: dts: sun8i: Add PWM controller node in H3
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-08-31 18:16:59 +02:00
Javier Martinez Canillas
5c4d9f0d49 ARM: dts: dra7: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:28 -07:00
Javier Martinez Canillas
387117c127 ARM: dts: dra62x: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:27 -07:00
Javier Martinez Canillas
f193a5ab3c ARM: dts: dm8168: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:27 -07:00
Javier Martinez Canillas
c5ee1b486f ARM: dts: dm8148: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:26 -07:00
Javier Martinez Canillas
0b086802cb ARM: dts: am572x: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:26 -07:00
Javier Martinez Canillas
9194cf4daa ARM: dts: am4372: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:25 -07:00
Javier Martinez Canillas
a60b9f45cc ARM: dts: am3517: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:25 -07:00
Javier Martinez Canillas
278cb79cc1 ARM: dts: am335x: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:24 -07:00
Javier Martinez Canillas
bfa130bbac ARM: dts: omap5: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:24 -07:00
Javier Martinez Canillas
742ae1f945 ARM: dts: omap4: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:23 -07:00
Javier Martinez Canillas
81777ff9dd ARM: dts: omap3: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:23 -07:00
Javier Martinez Canillas
101ace8d13 ARM: dts: omap2: Add missing unit name to memory nodes
This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:22 -07:00
Javier Martinez Canillas
75813028bb ARM: dts: am4372: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it shouldn't have
functional changes.

Since no am4372 based board had a memory node defined, a dummy node
is added so the compiled DTB memory node is the same than before.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:22 -07:00
Javier Martinez Canillas
55871eb6e2 ARM: dts: dra7: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:21 -07:00
Javier Martinez Canillas
06bfb9c199 ARM: dts: dm816x: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:21 -07:00
Javier Martinez Canillas
76155b378c ARM: dts: dm814x: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:20 -07:00
Javier Martinez Canillas
f8bf01611c ARM: dts: am33xx: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:20 -07:00
Javier Martinez Canillas
76a8548ea9 ARM: dts: omap5: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:19 -07:00
Javier Martinez Canillas
da6269e7e3 ARM: dts: omap4: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:19 -07:00
Javier Martinez Canillas
008a2ebcd6 ARM: dts: omap3: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:18 -07:00
Javier Martinez Canillas
d1f3156fc8 ARM: dts: omap2: Remove skeleton.dtsi usage
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:18 -07:00
Javier Martinez Canillas
766a1fe78f ARM: omap3: Add missing memory node in overo and torpedo boards
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

But these boards don't have a memory node defined, so removing the
skeleton.dtsi inclusion from omap3.dtsi will cause a change in the
compiled DTB. Add a dummy memory node so the compiled DTB doesn't
change if the skeleton.dtsi is removed from omap3.dtsi.

Eventually the correct starting addresses and sizes should be used
but I didn't find that information.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:18 -07:00
Javier Martinez Canillas
35852c68b2 ARM: am335x: Add missing memory node in sl50 board
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e1 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

But the sl50 board doesn't have a, so removing the  skeleton.dtsi
inclusion from am33xx.dtsi will cause a change in the compiled DTB.

The board has 512 MiB of RAM and its starting address is 0x80000000,
so add a proper memory device node in the DTS.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:40:17 -07:00
Grygorii Strashko
c097338ebd ARM: dts: dra7: cpsw: fix clocks tree
Current clocks tree definition for CPSW/CPTS doesn't
correspond TRM for dra7/am57 SoCs.

CPTS: has to be sourced from gmac_rft_clk_mux clock
CPSW: DPLL_GMAC -> CLKOUT_M2 -> GMAC_250M_CLK -> 1/2 ->
      -> GMAC_MAIN_CLK (125 MHZ)

Hence, correct clock tree for GMAC_MAIN_CLK and use proper
clock for CPTS. This also require updating of CPTS clock
multiplier.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:37:40 -07:00
J.D. Schroeder
dbb9c19632 ARM: dts: dra7: Fix clock data for gmac_gmii_ref_clk_div
This commit fixes the clock data inside the DRA7xx clocks device tree
structure for the gmac_gmii_ref_clk_div clock. This clock is actually
the GMAC_MAIN_CLK and has nothing to do with the register at address
0x4a0093d0. If CLKSEL_REF bit 24 inside of CM_GMAC_GMAC_CLKCTRL, is
set to 1 in order to use the GMAC_RMII_CLK instead of the
GMAC_RMII_HS_CLK, the kernel generates a clock divider warning:
    WARNING: CPU: 0 PID: 0 at drivers/clk/clk-divider.c:129 clk_divider_recalc_rate+0xa8/0xe0()
    gmac_gmii_ref_clk_div: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set

By properly configuring the gmac_gmii_ref_clk_div (GMAC_MAIN_CLK) to
have the parent of dpll_gmac_m2_ck always divided by 2 the warning is
resolved and the clock tree is fixed up.

Additionally, a new clock called rmii_50mhz_clk_mux is defined that
does utilize CM_GMAC_GMAC_CLKCTRL[24] CLKSEL_REF to configure the
source clock for the RMII_50MHZ_CLK.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Reviewed-by: Trenton Andres <trenton.andres@garmin.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-08-31 07:36:50 -07:00
Ard Biesheuvel
675b0563d6 arm64: cpufeature: expose arm64_ftr_reg struct for CTR_EL0
Expose the arm64_ftr_reg struct covering CTR_EL0 outside of cpufeature.o
so that other code can refer to it directly (i.e., without performing the
binary search)

Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 13:48:15 +01:00
Ard Biesheuvel
6f2b7eeff9 arm64: cpufeature: constify arm64_ftr_regs array
Constify the arm64_ftr_regs array, by moving the mutable arm64_ftr_reg
fields out of the array itself. This also streamlines the bsearch, since
the entire array can be covered by fewer cachelines. Moving the payload
out of the array also allows us to have special explicitly defined
struct instance in case other code needs to refer to it directly.

Note that this replaces the runtime sorting of the array with a runtime
BUG() check whether the array is sorted correctly in the code.

Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 13:48:15 +01:00
Ard Biesheuvel
5e49d73c1d arm64: cpufeature: constify arm64_ftr_bits structures
The arm64_ftr_bits structures are never modified, so make them read-only.

Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 13:48:15 +01:00
Kefeng Wang
6a6a4f1580 arm64: cleanup unused UDBG_* define
The UDBG_UNDEFINED/SYSCALL/BADABORT/SEGV are only used to show
verbose user fault messages in arm, not arm64, drop them.

Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 13:45:46 +01:00
PrasannaKumar Muralidharan
d6a38c0ba7 miscdevice: Use module_misc_device() macro
This patch removes module_init()/module_exit() from driver code by using
module_misc_device() macro. All modules in this patch has a print
statement which is removed when module_misc_device() macro is used.
If undesirable this patch can be dropped entirely, this is the only
purpose of making this as a separate patch.

Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-31 14:12:35 +02:00
PrasannaKumar Muralidharan
ca75d601b5 miscdevice: Add helper macro for misc device boilerplate
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.

This patch also converts drivers to use new macro.

Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.

Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-31 14:12:35 +02:00
Kim Phillips
b4a4485ed4 arm64: don't select PERF_USE_VMALLOC by default
Any arm64 based parts that have cache aliasing issues can set it
manually.  Apparently dragged in from ARM(32) defaults in commit
8c2c3df "arm64: Build infrastructure".

Signed-off-by: Kim Phillips <kim.phillips@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 12:32:46 +01:00
Michal Marek
cfa88c7946 arm64: Set UTS_MACHINE in the Makefile
The make rpm target depends on proper UTS_MACHINE definition.  Also, use
the variable in arch/arm64/kernel/setup.c, so that it's not accidentally
removed in the future.

Reported-and-tested-by: Fabian Vogt <fvogt@suse.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-08-31 12:31:38 +01:00