Q8 form factor A13 tablets have a 7" LCD panel. Unfortunately we
don't know the exact model of the panel. Just pick a panel with
display timings close to what we know.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Q8 tablets use the audio codec to provide audio output via a
headphone jack or a small mono speaker. A GPIO output is used to
control speaker amp.
The tablets may or may not have an internal microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A13 Q8 tablets, the PMIC's USB power supply (VBUS) is connected
to the external OTG port. This can be used to provide power and OTG VBUS
sensing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The output pin of LDO is also a GPIO pin, and the on/off settings of the
regulator are actually pinmux settings.
Disable it by default so it doesn't conflict with GPIO usage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the display engine is shared between the R8 and the A13. Move the
common parts to the Á13 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The RGB bus can be used in several configurations, one of which being the
RGB666.
Add a pinctrl group for that case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If the module has no clkctrl register defined, module_wait_ready should
not try to access this. This can potentially cause an illegal register
access, and result in bad idle reporting also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The previous implementation was racy in many locations, where the current
status of the clockdomain was read out, some operations were executed,
and the previous status info was used afterwards to decide next state
for the clockdomain. Instead, fix the implementation of the allow_idle /
deny_idle APIs to properly have usecounting support. This allows clean
handling internally within the clockdomain core, and simplifies the
usage also within hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the introduction of hwmod module clocks, the name of the hwmod
main clk may not be available before hwmod setup, as hwmod setup
may lookup the main clock dynamically based on the hwmod name.
Thus, change the order of hwmod setup and main clock handling for
the timer code, to make sure the main clock is going to be
available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the transition to hwmod module clocks, all hwmods will have
their main clocks named <hwmod_name>_mod_ck. Use this info to
fetch main_clk, and use it if found.
Also, if a main_clk is found based on the hwmod name, disable
the direct PRCM modulemode access from hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to introducing the new driver - ACT8945A MFD drive,
change the pmic device node to align with the ACT8945A
regulator and charger drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add power led node and rename status led node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add missing pinctrl information to ethernet node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ACT8945A is the PMIC present on the sama5d2 Xplained.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
After linking there are several symbols for the same address that the
__switch_to symbol points to. E.g.:
000000000089b9c0 T __kprobes_text_start
000000000089b9c0 T __lock_text_end
000000000089b9c0 T __lock_text_start
000000000089b9c0 T __sched_text_end
000000000089b9c0 T __switch_to
When disassembling with "objdump -d" this results in a missing
__switch_to function. It would be named __kprobes_text_start
instead. To unconfuse objdump add a nop in front of the kprobes text
section. That way __switch_to appears again.
Obviously this solution is sort of a hack, since it also depends on
link order if this works or not. However it is the best I can come up
with for now.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Expose the maximum thread id with /proc/cpuinfo.
With the new line the output looks like this:
vendor_id : IBM/S390
bogomips per cpu: 20325.00
max thread id : 1
With this new interface it is possible to always tell the correct
number of cpu threads potentially being used by the kernel.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This avoids the need to add most of the clock aliases under
drivers/clk/ti/clk-xyz.c files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I found one more make randconfig build error with the recent
SMP kexec changes. We need the mpuss now always available early.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang
with kexec")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have both KERN_TO_HYP and kern_hyp_va, which do the exact same
thing. Let's standardize on the latter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This is more of a safety measure than anything else: If we end-up
with an idmap page that intersect with the range picked for the
the HYP VA space, abort the KVM setup, as it is unsafe to go
further.
I cannot imagine it happening on 64bit (we have a mechanism to
work around it), but could potentially occur on a 32bit system with
the kernel loaded high enough in memory so that in conflicts with
the kernel VA.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We can now remove a number of dead #defines, thanks to the trampoline
code being gone.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
So far, KVM was getting in the way of kexec on 32bit (and the arm64
kexec hackers couldn't be bothered to fix it on 32bit...).
With simpler page tables, tearing KVM down becomes very easy, so
let's just do it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Just like for arm64, we can now make the HYP setup a lot simpler,
and we can now initialise it in one go (instead of the two
phases we currently have).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
There is no way to free the boot PGD, because it doesn't exist
anymore as a standalone entity.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Since we now only have one set of page tables, the concept of
boot_pgd is useless and can be removed. We still keep it as
an element of the "extended idmap" thing.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that we only have the "merged page tables" case to deal with,
there is a bunch of things we can simplify in the HYP code (both
at init and teardown time).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We're in a position where we can now always have "merged" page
tables, where both the runtime mapping and the idmap coexist.
This results in some code being removed, but there is more to come.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Add the code that enables the switch to the lower HYP VA range.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Declare the __hyp_text_start/end symbols in asm/virt.h so that
they can be reused without having to declare them locally.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we move towards a selectable HYP VA range, it is obvious that
we don't want to test a variable to find out if we need to use
the bottom VA range, the top VA range, or use the address as is
(for VHE).
Instead, we can expand our current helper to generate the right
mask or nop with code patching. We default to using the top VA
space, with alternatives to switch to the bottom one or to nop
out the instructions.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Define the two possible HYP VA regions in terms of VA_BITS,
and keep HYP_PAGE_OFFSET_MASK as a temporary compatibility
definition.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we need to indicate to the rest of the kernel which region of
the HYP VA space is safe to use, add a capability that will
indicate that KVM should use the [VA_BITS-2:0] range.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
HYP_PAGE_OFFSET is not massively useful. And the way we use it
in KERN_HYP_VA is inconsistent with the equivalent operation in
EL2, where we use a mask instead.
Let's replace the uses of HYP_PAGE_OFFSET with HYP_PAGE_OFFSET_MASK,
and get rid of the pointless macro.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
hyp_kern_va is now completely unused, so let's remove it entirely.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
__hyp_panic_string is passed via the HYP panic code to the panic
function, and is being "upgraded" to a kernel address, as it is
referenced by the HYP code (in a PC-relative way).
This is a bit silly, and we'd be better off obtaining the kernel
address and not mess with it at all. This patch implements this
with a tiny bit of asm glue, by forcing the string pointer to be
read from the literal pool.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Since dealing with VA ranges tends to hurt my brain badly, let's
start with a bit of documentation that will hopefully help
understanding what comes next...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
I don't think any single piece of the KVM/ARM code ever generated
as much hatred as the GIC emulation.
It was written by someone who had zero experience in modeling
hardware (me), was riddled with design flaws, should have been
scrapped and rewritten from scratch long before having a remote
chance of reaching mainline, and yet we supported it for a good
three years. No need to mention the names of those who suffered,
the git log is singing their praises.
Thankfully, we now have a much more maintainable implementation,
and we can safely put the grumpy old GIC to rest.
Fellow hackers, please raise your glass in memory of the GIC:
The GIC is dead, long live the GIC!
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch updates the event constraints for non-PEBS mode for
Intel Broadwell and Skylake processors. When HT is off, each
CPU gets 8 generic counters. However, not all events can be
programmed on any of the 8 counters. This patch adds the
constraints for the MEM_* events which can only be measured on the
bottom 4 counters. The constraints are also valid when HT is off
because, then, there are only 4 generic counters and they are the
bottom counters.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Link: http://lkml.kernel.org/r/1467411742-13245-1-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds basic chip support for MT6755 SoC.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>