* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] boot cputime accounting
[S390] add read_persistent_clock
[S390] cpu hotplug and accounting values
[S390] fix idle time accounting
[S390] smp: fix cpu_possible_map initialization
[S390] dasd: fix idaw boundary checking for track based ccw
[S390] dasd: Use the new async framework for autoonlining.
[S390] qdio: remove dead timeout handler
[S390] appldata: Use new mod_virt_timer_periodic() function.
[S390] extend virtual timer interface by mod_virt_timer_periodic
[S390] stp synchronization retry timer
[S390] call nmi_enter/nmi_exit on machine checks
[S390] wire up preadv/pwritev system calls
[S390] s390: move machine flags to lowcore
Impact: fix crash with many devices
I found this crash:
[ 552.616646] general protection fault: 0403 [#1] SMP
[ 552.620013] last sysfs file:
/sys/devices/pci0000:00/0000:00:02.0/usb1/1-1/1-1:1.0/host13/target13:0:0/13:0:0:0/block/sr0/size
[ 552.620013] CPU 0
[ 552.620013] Modules linked in:
[ 552.620013] Pid: 0, comm: swapper Not tainted 2.6.30-rc1-tip-01931-g8fcafd8-dirty #28 Sun Fire X4440
[ 552.620013] RIP: 0010:[<ffffffff8023bada>] [<ffffffff8023bada>] default_idle+0x7d/0xda
[ 552.620013] RSP: 0018:ffffffff81345e68 EFLAGS: 00010246
[ 552.620013] RAX: 0000000000000000 RBX: ffffffff8133d870 RCX: ffffc20000000000
[ 552.620013] RDX: 00000000001d0620 RSI: ffffffff8023bad8 RDI: ffffffff802a3169
[ 552.620013] RBP: ffffffff81345e98 R08: 0000000000000000 R09: ffffffff812244a0
[ 552.620013] R10: ffffffff81345dc8 R11: 7ebe1b6fa0bcac50 R12: 4ec4ec4ec4ec4ec5
[ 552.620013] R13: ffffffff813a54d0 R14: ffffffff813a7a40 R15: 0000000000000000
[ 552.620013] FS: 00000000006d1880(0000) GS:ffffc20000000000(0000) knlGS:0000000000000000
[ 552.620013] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[ 552.620013] CR2: 00007fec9d936a50 CR3: 000000007d1a9000 CR4: 00000000000006e0
[ 552.620013] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 552.620013] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 552.620013] Process swapper (pid: 0, threadinfo ffffffff81344000,task ffffffff812244a0)
[ 552.620013] Stack:
[ 552.620013] 0000000000000000 ffffc20000000000 00000000001d0620 7ebe1b6fa0bcac50
[ 552.620013] ffffffff8133d870 4ec4ec4ec4ec4ec5 ffffffff81345ec8 ffffffff8023bd84
[ 552.620013] 4ec4ec4ec4ec4ec5 ffffffff813a54d0 7ebe1b6fa0bcac50 ffffffff8133d870
[ 552.620013] Call Trace:
[ 552.620013] [<ffffffff8023bd84>] c1e_idle+0x109/0x124
[ 552.620013] [<ffffffff8023314b>] cpu_idle+0xb8/0x101
[ 552.620013] [<ffffffff80c16d6a>] rest_init+0x7e/0x94
[ 552.620013] [<ffffffff81357efc>] start_kernel+0x3dc/0x3fd
[ 552.620013] [<ffffffff813572a9>] x86_64_start_reservations+0xb9/0xd4
[ 552.620013] [<ffffffff813573b2>] x86_64_start_kernel+0xee/0x109
[ 552.620013] Code: 48 8b 04 25 f8 b4 00 00 83 a0 3c e0 ff ff fb 0f ae f0 65 48 8b 04 25 f8 b4 00 00 f6 80 38 e0 ff ff 08 75 09 e8 71 76 06 00 fb f4 <eb> 06 e8 68 76 06 00 fb 65 48 8b 04 25 f8 b4 00 00 83 88 3c e0
[ 552.620013] RIP [<ffffffff8023bada>] default_idle+0x7d/0xda
[ 552.620013] RSP <ffffffff81345e68>
[ 552.828646] ---[ end trace 4cbfc5c01382af7f ]---
Joerg Roedel said
"The 0403 error code means that there was an external interrupt with vector
0x80. Yinghai, my theory is that the kernel on this machine has no 32bit
emulation compiled in, right? In this case the selector points to a zero entry
which may cause the #gpf right after the hlt.
But I have no idea where the external int 0x80 comes from"
it turns out that we could use 0x80 for external device on 64-bit
when 32-bit emulation is disabled.
But we forgot to set the gate for it.
try to set gate for it by checking used_vectors.
Also move apic_intr_init() early to avoid setting
that gate two times.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <49E62DFD.6010904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: pseries/dtl.c should include asm/firmware.h
powerpc: Fix data-corrupting bug in __futex_atomic_op
powerpc/pseries: Set error_state to pci_channel_io_normal in eeh_report_reset()
powerpc: Allow 256kB pages with SHMEM
powerpc: Document new FSL I2C bindings and cleanup
powerpc/mm: Fix compile warning
powerpc/85xx: TQM8548: update defconfig
powerpc/85xx: TQM8548: use proper phy-handles for enet2 and enet3
powerpc/85xx: TQM85xx: correct address of LM75 I2C device nodes
powerpc: Add support for early tlbilx opcode
powerpc: Fix tlbilx opcode
It turns out that 'smp_call_function_many()' doesn't work at all like
'smp_call_function_single()', and my change to Andrew's patch to use it
rather than a loop over all CPU's acpi-cpufreq doesn't work.
My bad.
'smp_call_function_many()' has two "features" (aka "documented bugs"):
(a) it needs to be called with preemption disabled, because it uses
smp_processor_id() without guarding the CPU lookup with 'get_cpu()'
and 'put_cpu()' like the 'single' variant does.
(b) even if the current CPU is part of the CPU mask, it won't do the
call on that CPU.
Still, we're better off trying to use 'smp_call_function_many()' than
looping over CPU's, since it at least in theory allows us to use a
broadcast IPI and do it all in parallel. So let's just work around the
silly semantic bugs in that function.
Reported-and-tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SD/MMC to the s3c2410_defconfig, building in the core
and adding the rest of the drivers as modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the machine configuration of s3c2410_defconfig to
add support for newer machines, and update the s3c24xx
specific options.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the list of modules being built for the network
core of the s3c2410_defconfig. This update adds such
items as TCP congestion, netfilter for IPv4 and IPv6.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Going forward gpio_request() will be a requirement for GPIO API users so
call it for the LCD power GPIOs. With present code the kernel functions
but generaets loud WARN_ON()s when using the unrequested GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
IOMMU_LEAK, GART's own feature, dumps the used IOMMU entries when
IOMMU entries is full, which might be useful to find a bad driver that
eats IOMMU entries.
DMA_API_DEBUG provides the similar feature, debug_dma_dump_mappings,
and it's better than GART's IOMMU_LEAK feature. GART's IOMMU_LEAK
feature doesn't say who uses IOMMU entries so it's hard to find a bad
driver.
This patch reimplements the GART's IOMMU_LEAK feature by using
DMA_API_DEBUG.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1239669799-23579-2-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Converting node_to_k8_nb_misc() from a macro to an inline function
makes compiler see the 'node' parameter in the !CONFIG_K8_NB too,
which eliminates these compiler warnings:
arch/x86/kernel/cpu/intel_cacheinfo.c: In function ‘show_cache_disable’:
arch/x86/kernel/cpu/intel_cacheinfo.c:712: warning: unused variable ‘node’
arch/x86/kernel/cpu/intel_cacheinfo.c: In function ‘store_cache_disable’:
arch/x86/kernel/cpu/intel_cacheinfo.c:739: warning: unused variable ‘node’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
LKML-Reference: <1239730477.2966.26.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove some pointless conditionals before kfree().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix trivial build warning due to incompatible pointer type.
ep93xx_timer_interrupt() has the wrong return type causing a
warning during the build.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unmapping N pages (e.g. shared memory) the amount of TLB flushes
done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it should be N at
maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8 pages, so there is a
noticeable performance penalty when unmapping a large VMA and the system
is spending its time in flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh Dickins,
and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger mappings
even more.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A randconfig build on powerpc failed with:
dtl.c: In function 'dtl_init':
dtl.c:238: error: implicit declaration of function 'firmware_has_feature'
dtl.c:238: error: 'FW_FEATURE_SPLPAR' undeclared (first use in this function)
- We need firmware.h for these definitions.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Richard Henderson pointed out that the powerpc __futex_atomic_op has a
bug: it will write the wrong value if the stwcx. fails and it has to
retry the lwarx/stwcx. loop, since 'oparg' will have been overwritten
by the result from the first time around the loop. This happens
because it uses the same register for 'oparg' (an input) as it uses
for the result.
This fixes it by using separate registers for 'oparg' and 'ret'.
Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>
While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.
Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.
The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure. Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.
The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.
Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.
Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.
PAPR defines the following 3 states:
0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
(Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
(Slot Frozen)
An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.
The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that shmem's divisions by zero and SHMEM_MAX_BYTES are fixed,
let powerpc 256kB pages coexist with CONFIG_SHMEM again.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MioA701 board's GPIO95 is the AC97 line. The other GPIO113
is not connected to the sound chip, but to the GSM chip as a
wakeup line.
It happens that when the pxa2xx_ac97 driver reconfigures the
gpio as an "out gpio" for AC97 reset (bug workaround), it
hangs the GSM chip.
As AC97 platform data now enables to specify the AC97 reset
line, use it.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Currently there are two possible platform datas for the PXA AC97 driver:
one supported by the generic AC97 driver only which provides callbacks
to allow board-specific configuration at stream startup and teardown,
and another for pxa2xx-ac97-lib which allows configuration of the reset
GPIO for PXA2xx CPUs.
Obviously this won't actually work when using the generic AC97 driver
since the drivers will attempt to parse the platform data in both
formats. Fix this by merging the two structures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Interrupts must be disabled when taking the IPI lock.
Caught by lockdep.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert part of af5c820a31 ("x86: cpumask:
use work_on_cpu in arch/x86/kernel/microcode_core.c")
That change is causing only one Intel CPU's microcode to be updated e.g.
microcode: CPU3 updated from revision 0x9 to 0x17, date = 2005-04-22
where before it announced that also for CPU0 and CPU1 and CPU2.
We cannot use work_on_cpu() in the CONFIG_MICROCODE_OLD_INTERFACE code,
because Intel's request_microcode_user() involves a copy_from_user() from
/sbin/microcode_ctl, which therefore needs to be on that CPU at the time.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Add in PCI bus for DMA API debugging.
sh: Pre-allocate a reasonable number of DMA debug entries.
sh: sh7786: modify usb setup timeout judgment bug.
MAINTAINERS: Update sh architecture file patterns.
sh: ap325: use edge control for ov772x camera
sh: Plug in support for ARCH=sh64 using sh SRCARCH.
sh: urquell: Fix up address mapping in board comments.
sh: Add support for DMA API debugging.
sh: Provide cpumask_of_pcibus() to fix NUMA build.
sh: urquell: Add board comment
sh: wire up sys_preadv/sys_pwritev() syscalls.
sh: sh7785lcr: fix PCI address map for 32-bit mode
sh: intc: Added resume from hibernation support to the intc
This patch enables each partition's BAU distribution bit map
to be partition-relative.
The distribution bitmap had been constructed assuming 0 as the base
node number. That construct would not have allowed a total system of
greater than 256 nodes.
It also corrects an error that occurred when the first blade's nasid
was not zero. That nasid was stored as the base node.
The base node number gets added by hardware to the node numbers implied
in the distribution bitmap, resulting in invalid target nasids.
Tested on the UV hardware simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1Ltl0C-0004Ob-37@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In commit 51dcdfec6a ("parport: Use the
PCI IRQ if offered") parport_pc_probe_port() gained an irqflags arg.
This isn't being supplied on powerpc. This patch make powerpc fallback
to the old behaviour, that is using "0" for irqflags.
Fixes build failure:
In file included from drivers/parport/parport_pc.c:68:
arch/powerpc/include/asm/parport.h: In function 'parport_pc_find_nonpci_ports':
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
make[3]: *** [drivers/parport/parport_pc.o] Error 1
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit a7bb3909b3 ("spi: pxa2xx_spi:
introduce chipselect GPIO to simplify the common cases") the .gpio_cs
field in pxa2xx_spi_chip has to be set explicitly.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Start the cpu time accounting very early to catch the cpu time spent
for the initial kernel setup. To make the output of /proc/uptime
match the sum of all cpu accounting values of the boot cpu reset
xtime and wall_to_monotonic to sane values based on the TOD clock.
The values set by timekeeping_init are off by up to a second.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a read_persistent_clock function that does not just return 0.
Since timekeeping_init calls the function before time_init has been
called move reset_tod_clock to early.c to make sure that the TOD
clock is running when read_persistent_clock is invoked.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reset the cpu timer to the maximum value and correctly initialize the
cpu accounting values in the lowcore when the cpu is started.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The steal time is calculated by subtracting the time the virtual cpu
has been running on a physical cpu from the wall clock time. To make
that work all wall time needs to be added to the steal time field first
before the virtual cpu time is subtracted.
The time between the last clock update and the load of the enabled wait
psw needs to be added to the steal_time field as well to make the sum
over all cpu accounting numbers match the wall clock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu_possible_map by default is initialized with all ones in s390.
If the kernel paramert possible_cpus=<x> is passed the cpu_possible_map
is supposed to have x bits set.
However the current code just sets the x bits without clearing the NR_CPUS
bits that were already set. So we end up with an unchanged map that has
all bits set.
To fix this just clear the map before setting any new bits.
This broke with def6cfb70b
"[S390] cpumask: Use accessors code."
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
mod_virt_timer() was used to modify/add cpu timers for cpus that were
set online. This resulted in a one-shot timer for every cpu that was
newly added or previously set offline, instead of an interval timer,
which broke the appldata vtime interval setup.
To fix this, the new mod_virt_timer_periodic() function is used, which
adds interval timers instead of one-shot timers.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case mod_virt_timer is used to add a non pending timer the timer
is always added as a one-shot timer. If mod_virt_timer is used for
periodic timers they may therfore be degraded to one-shot timers.
Add mod_virt_timer_periodic to the interface to allow safe re-programming
of the interval value.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a timer that retries the clock synchronization via the server time
protocol if there is a usable clock but the synchronization failed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
nmi_enter/nmi_exit includes the lockdep calls and various
other calls which were missing so far.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CONFIG_IOMMU_DEBUG has depends on CONFIG_GART_IOMMU:
config IOMMU_DEBUG
bool "Enable IOMMU debugging"
depends on GART_IOMMU && DEBUG_KERNEL
depends on X86_64
So it's not useful to have CONFIG_IOMMU_DEBUG in Calgary IOMMU code,
which does the extra checking of the bitmap space management.
And Calgary uses the iommu helper for the bitmap space management now
so it would be better to have the extra checking feature in the iommu
helper rather than Calgary code (if necessary).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: alexisb@us.ibm.com
LKML-Reference: <20090414120827G.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
%p prints out 0x000000000000000 as (null)
so use %lx instead.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49E43282.1090607@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: unification of declarations, cleanup
Unification of declarations:
moved init_memory_mapping, initmem_init and free_initmem from
page_XX_types.h to page_types.h
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1239693869.3033.31.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>