This patch adds backtracing capability to oprofile profiling in kernel
and user mode on AVR32. This is done by going through the frames on the
stack and adding oprofile traces for all return addresses. The code
being profiled has to be compiled with frame pointers to make this work.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for a low(er)-power suspend-to-RAM.
In addition to the SDRAM being put into self-refresh mode, the Master
Clock is set to the Slow-clock rate (32Khz) and PLLA & PLLB are
disabled.
Certain peripherals are therefore also disabled, and thus cannot be
used as wakeup sources.
This patch has been included in the AT91 patches in various forms
since 2.6.19 and a number of people have worked or commented on it,
most notably:
Savin Zlobec (for the original AT91RM9200 support)
Anti Sullin (for the SAM9260 version)
David Brownell, etc.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the various GPIO-connected buttons to be used as wakeup sources.
Also enable the internal GPIO pullup.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support or the GPIO-connected buttons on the Atmel AT91SAM9260-EK board.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds initialization of the Touchscreen controller for the
AT91SAM9RL processor.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the PWM controller and leds-atmel-pwm.c driver to drive a LED on
the Atmel AT91SAM9263-EK board.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_devices and configuration of the PWM controller found on
Atmel AT91CAP9, SAM9263 and SAM9RL processors.
SAM9263 support by Sedji Gaouaou.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the various AT91 board files, replace hard-coded size values (eg,
0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h
Also replace MTD partition offsets with MTDPART_OFS_NXTBLK.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use unsigned loads to avoid possible misscalculation of IP checksums. This
bug was instruced in f761106cd728bcf65b7fe161b10221ee00cf7132 (lmo) /
ed99e2bc1d (kernel.org).
[Original fix by Atsushi. Improved instruction scheduling and fix for
unaligned unsigned load by me -- Ralf]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I have no SPARC compiler handy to verify, but it looks like this
is another file that doesn't need <linux/miscdevices.h> ...
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Meelis Roos.
The OF device layer builds properties by matching bus types and
applying 'range' properties as appropriate, up to the root.
The match for "PCI" busses is looking at the 'device_type' property,
and this does work %99 of the time.
But on an E3500 system with a PCI QFE card, the DEC 21153 bridge
sitting above the QFE network interface devices has a 'name' of "pci",
but it completely lacks a 'device_type' property. So we don't match
it as a PCI bus, and subsequently we end up with no resource values at
all for the devices sitting under that DEC bridge.
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:
- The page fault handler / TLB miss
- IPC calls
- Kernel thread creation
The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.
The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.
Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the powerpc commit f6a616800e
'[POWERPC] Fix kernel stack allocation alignment'.
SH has traditionally forced the thread order to be relative to the page
size, so there were never any situations where the same bug was
triggered by slub. Regardless, the usage of > 8kB stacks for the larger
page sizes is overkill, so we switch to using slab allocations there,
as per the powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This combination triggers a divide by zero in kernel/fork.c when
calculating the initial max_threads value:
max_threads = mempages / (8 * THREAD_SIZE / PAGE_SIZE);
Simply disable 4K stacks on 64kB PAGE_SIZE to work around this,
as it's not a terribly useful combination to begin with.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since the first argument is always NULL, the only side effect
is to disable the PROFILE_IRQ, so just do that directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the only use of the clear_profile_irq() btfixup entry,
which just eats up lots of dead space on other platform types.
A subsequent commit will delete the other implementations and
the btfixup entry as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4611a77 ("[IA64] fix compile failure with non modular builds")
introduced struct fdesc into asm/elf.h, which duplicates KVM's definition.
Remove the latter to avoid the build error.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
Fix compile failure with non modular builds
powerpc: Holly board needs dtbImage target
powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
[ARM] omap: back out 'internal_clock' support
[ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()
