- Use the normal cross gcc instead of using an elf specific cris toolchain.
This removes the dependency of this second toolchain.
- Use the normal cross objcopy instead of overriding it to use elf-toolchain.
This allows compiling using "CROSS_COMPILE=$CRIS_GCC/cris-axis-linux-gnu-"
instead of just "CROSS_COMPILE=$CRIS_GCC/cris-axis-linux-gnu/bin/"
- Remove redundant rules for compiling, the implicit rules are sufficient.
- Convert the arch/cris/arch-v10/boot/compressed/head.S to format
accepted by the cris-axis-linux-gnu-gcc (registers must be prefixed
with '$', remove explicit underscore on exported symbols)
- Remove a number of unused (and duplicated) prototypes from
arch/cris/arch-v10/boot/compressed/misc.c.
- Correct memcpy and memset return values (actually return them!)
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add dummy ops for serial debug port.
Add setting of c_ispeed/c_ospeed as suggested by Alan Cox.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Apparently, DOS and possibly other legacy operating systems issued a
null command to the keyboard controller after toggling A20,
specifically "pulse output pins" with no output pins specified. This
was presumably done for synchronization reasons. This has made it
into at least the UHCI spec, and it has been found to cause
compatibility problems when "legacy USB" is enabled (which it almost
always is) to not have this byte sent.
It is *NOT* clear if any of these compatibility problems has any
effect on Linux. However, for maximum compatibility, issue this null
command after togging A20 through the KBC.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Russell King did the following back in 2003:
<-- snip -->
[PCI] pci-9: Kill per-architecture pcibios_update_resource()
Kill pcibios_update_resource(), replacing it with pci_update_resource().
pci_update_resource() uses pcibios_resource_to_bus() to convert a
resource to a device BAR - the transformation should be exactly the
same as the transformation used for the PCI bridges.
pci_update_resource "knows" about 64-bit BARs, but doesn't attempt to
set the high 32-bits to anything non-zero - currently no architecture
attempts to do something different. If anyone cares, please fix; I'm
going to reflect current behaviour for the time being.
Ivan pointed out the following architectures need to examine their
pcibios_update_resource() implementation - they should make sure that
this new implementation does the right thing. #warning's have been
added where appropriate.
ia64
mips
mips64
This cset also includes a fix for the problem reported by AKPM where
64-bit arch compilers complain about the resource mask being placed
in a u32.
<-- snip -->
This patch removes the unused pcibios_update_resource() functions the
kernel gained since, from FRV, m68k, mips & sh architectures.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
From the code:
"B stepping K8s sometimes report an truncated RIP for IRET exceptions
returning to compat mode. Check for these here too."
The code then proceeds to truncate the upper 32 bits of %rbp. This means
that when do_page_fault() is finally called, its prologue,
do_page_fault:
push %rbp
movl %rsp, %rbp
will put the truncated base pointer on the stack. This means that the
stack tracer will not be able to follow the base-pointer changes and
will see all subsequent stack frames as unreliable.
This patch changes the code to use a different register (%rcx) for the
checking and leaves %rbp untouched.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Basic I2C initialization for the NGW100 board:
- Provide empty i2c device table. Daughtercards may add devices,
and the ATtiny24 could do stuff too.
- Set up EXTINT(3) so the ATtiny24 can interrupt the AP7000.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.
The function for adding the PSIF platform device is also added to the
board header file.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
__raw_readsb() should always use byte accesses, never halfword accesses,
to I/O memory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A signal handler should be able to change the signal stack used for the
next signal by altering the ucontext_t passed as a parameter to the
handler. This does not currently work on avr32 since it doesn't update
the in-kernel signal context from the ucontext_t upon signal handler
return.
Fix it by adding a call to do_sigaltstack() from sys_rt_sigreturn(),
bringing it in line with most other architectures.
Signed-off-by: Martin Koegler <mkoegler@auto.tuwien.ac.at>
[haavard.skinnemoen@atmel.com: changed patch description]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On our custom board we have other oscillator rates than on atngw100 and
atstk100x.
Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.
This patch moves them into board specific code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fixes one of two ext4 build problems:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
fix:
arch/x86/kernel/process.c: In function 'cpu_idle_wait':
arch/x86/kernel/process.c:64: error: too many arguments to function 'smp_call_function'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix typo causing:
arch/x86/kernel/built-in.o: In function `__unmap_single':
amd_iommu.c:(.text+0x17771): undefined reference to `iommu_area_free'
arch/x86/kernel/built-in.o: In function `__map_single':
amd_iommu.c:(.text+0x1797a): undefined reference to `iommu_area_alloc'
amd_iommu.c:(.text+0x179a2): undefined reference to `iommu_area_alloc'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/amd_iommu.c: In function ‘amd_iommu_init_dma_ops':
arch/x86/kernel/amd_iommu.c:940: error: lvalue required as left operand of assignment
arch/x86/kernel/amd_iommu.c:941: error: lvalue required as left operand of assignment
due to !CONFIG_GART_IOMMU.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/amd_iommu_init.c:247: warning: 'struct acpi_table_header' declared inside parameter list
arch/x86/kernel/amd_iommu_init.c:247: warning: its scope is only this definition or declaration, which is probably not what you want
arch/x86/kernel/amd_iommu_init.c: In function 'find_last_devid_acpi':
arch/x86/kernel/amd_iommu_init.c:257: error: dereferencing pointer to incomplete type
arch/x86/kernel/amd_iommu_init.c:265: error: dereferencing pointer to incomplete type
the AMD IOMMU code depends on ACPI facilities.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
